HT1178 wifi to set up time capsule

if i don't have the cable can i set up time capsule using wifi?

You will need to connect an Ethernet cable to the WAN "O" port on the Time Capsule to establish a wired connection to your modem or router.
Once this is done, the Time Capsule can be set up using wireless from a computer, iPad or iPhone.

Similar Messages

HT1178 I have set up Time Capsule to use with Time Machine. When I open Time Machine it 'cannot find' the Time Capsule and I have the Select the Disk each time. In the Next Backup tab it always says "When disk is connected" even though the disk is alrea

I have set up Time Capsule to use with Time Machine but when I open Time Machine it 'cannot find' the Time Capsule and I have to 'Select the Disk' each time. In the Next Backup tab it always says "When disk is connected" even though the disk is already connected.

Your pro doesn't matter.. I presume it is happily working.
Your imac setup has got messed up because you changed from a local (my book being USB type I presume) to network drive. Did you do a clean install of Lion?
Did you use the backup from the Pro on the imac? Otherwise I don't see how the Pro shows up in use previous disk. Where is Pondini when you need him??
You cannot download Time Machine as an App and replace the current version. It is built into the OS.. the only way to do it is a clean install. Unfortunately that might be the only way around the issue.
There is a number of issues that Pondini has covered in the setup issues of troubleshooting.
This is the most relevant I think. http://pondini.org/TM/B6.html
But look at the whole section B setup problems.
http://pondini.org/TM/Troubleshooting.html
If it was me, I would store all the info you need.. not using TM but using a straight copy of files.
Then clean install Lion. I doubt any of these issues would exist if you had not installed Lion over existing setup or used a different backup.
See if you can get Pondini to respond.. !!

How to set up time capsule with BT home hub 4.0 & Openreach

Idiots guide needed.
My TimeCapsule (year old model) had been running well from my BT Openreach box (without using the Home Hub 4.0) but recently had issues with connection dropping - BT said they've sorted out their end and can't see any remaining issues and can't offer me any more support if I'm not using the Home Hub 4.0
I reset the TC to run straight from the Openreach Box still have issues with wi-fi dropping in and out (both on ethernet and wi-fi).
Can I:....
1) set up Time Capsule running from BT Home Hub 4.0 which itself runs from BT Openreach white box (thus continuing to get support from BT)
or should i go back to
2) Time Capsule running straight from BT Openreach Box
Can some one post an idiots guide to either option?
Other stuff that may be important.
Macbook air running Yosemite (mid 2011 model)
Apple TV
Airportexpress
Time Capsule
2 x iphone 4s
Kids PC
Ethernet and wifi for above - I generally run everything hard wired via ethernet.

The easiest and sure way is to use bridge on the TC as the method of connection. The TC then becomes a device in your network and gets its IP from the main router that I presume BT supply.
Method is,
1. Plug the TC WAN port into the BT supplied modem by ethernet.
2. Plug the computer you are using for the setup into the TC by ethernet.
3. Run the airport utility .. go to internet tab on the top menu..
In the bottom option, Connection Sharing choose off (bridged mode)
4. Go to the wireless page and setup wireless connection as you like it.. using whichever band you want. And make sure security is set to the highest setting, wpa2 personal. Put in a decent wireless passkey.
5. Press the update and fix whatever else the TC will show as needing fixing.. usually security stuff.
6. You can then disconnect the ethernet and connect by wireless if you want. Any port on the TC will now be a LAN port, including WAN.
This is assuming BT supply a wireless router with built in vdsl/other type of modem. If so you normally will not be able to bridge the modem, unless BT are using pppoe authentication which they haven't in the past.
If you really need to use the TC as a router then you will need to work out an alternative method. You can double NAT by placing the TC in the DMZ of the BT router if that is an option. It is not without issues in general.

Cannot print or scan with USB printer over wifi from airport express / time capsule wifi

Hi everybody,
I have recently set up time capsule connected to the router from the telephone company but created a new wifi network for the time machine to better work. Now I have bought an airport express to be able to use my USB printer over the WIFI network. I have to laptops, the printing works fine over the mac book air but not over the macbook pro. On top of that I cannot scan with either of the devices.
I have scanned most of the information out there but this issue seems not to be addressed properly anywhere. Advices given do always repeat itself but no solution worked for me.
Now I have plugged the usb from the printer directly back into mac book pro and the problem seems to persist here too. The message I receive everywhere is this one:
The software for the printer was installed incorrectly.
Would you like it to be repaired?
When I hit the Repair button a notice says 'repairing permissions' but nothing really happens. In the end nothing has been printed.
Resetting the printing systems has not really changed anything either. The problems persist.
This is the screen I get when the printer is directly plugged in through USB:
Result: printer recognised and installed, I cannot print (The software for the printer was installed incorrectly), but I can scan (probably because of the hint ('multifunction')
When I try to install the printer through the network connection (wifi network over time capsule and airport express) I get this image:
Result: printer recognised over bonjour but without multifunction (in other words without scanning), I cannot scan nor print (The software for the printer was installed incorrectly)
As I already mentioned any solution I found online would not work. Now the qustions are:
1) why can't I print? The drivers seem to be there but somehow broken, and I don't know how to repair it
2) why can't I scan over wifi? It sould possible that any function that can be performed over cable should also be able to performable over air, right?
I would very much appreciate any kind of help.
Thank you in advance,
Cris

What's up doc?
HP has not provided "network" drivers to allow advanced features when the the All-in-One is connected to the USB port on the Time Capsule.
Therefore, only the printing function is supported when the All-in-One is connected to the Time Capsule's USB port.
If you need advanced features like fax, copy, scan, maintenance etc., you will need to connect over the WiFI network, or connect the All-in-One directly to your computer.

No Internet access after setting up time capsule

I am setting an airport time capsule. After setting up new network, I no longer have Internet access and can not set up the time capsule. I have tried to cycle the power on my model but no luck. Any ideas?

Disconnect all connections from the Time Capsule except the AC power cord.
With the Time Capsule powered on for a few minutes, hold in the reset button on the back of the device for 10-12 seconds and release
Allow a full minute for the Time Capsule to restart to a slow, blinking amber light
Connect an Ethernet cable from one of the LAN <--> ports on the Actiontec modem/router to the WAN "O" port on the Time Capsule
Open up AirPort Utility
Click on Other WiFi Devices
Click on Time Capsule
The utility will display a window that looks similar to the illustration below, excep that there will be a picture of the Time Capsule instead of an AirPort Express
Network Name......Enter a name that you want to call the wireless network
Base Station Name....Enter a name that you want to call the Time Capsule
Password......Enter a password that will be used for both the wireless and device name
Verify the password
Click Next
When you see the the message of Setup Complete, click Done
Now you can select the new network that you created and enter the password to connect
Try to keep the Actionec modem/router and Time Capsule at least 6-8 feet (or 2 meters) apart from each other to help minimimize the chances of wireless interference between them.

I can`t set my Time Capsule

Hi people, my doubt can seem quiet simple, but I'm unable to set my Time Capsule. I'll tell you.
I a new mac user, I've got a MacBookPro, and I just bought a Time Capsule (2Tb), but I don't know to set it for first time. I've followed the next steps:
1 - I've connect the TC to my router WI-FI by ethernet cable.
2 - I've plug in my TC.
3 - I've started my MacBookPro.
4 - I've started "Airport Utility" from folder "Utilities" (in "Applications").
5 - But then start the problem, 'cause Airport Utility doesn't find any base station or gadget, just say me that internet is OK, but the software can be hours searching with the next message: "Not found any Airport base station set. Airport utility will continue searching". So, after hours, I don't get any answer.
S.O.S. friends.
Thanks in advanced and sorry for my english.

But now, I've got a new question:
Does TC just work linked to the main router?
Is not possible that TC works by wi-fi, without cables?
Thanks.
Ok,, the TC is primarily designed to use ethernet WAN.. if you try and use wifi to connect it is not as good or reliable. You gain nothing.. but it depends on what you mean..
If the wifi from the existing router is good.. just turn off wifi in the TC.. plugged into the main router by ethernet you are now accessing it as fast as you would directly.. If you want faster connection, plug ethernet directly into TC lan port.
If you join by wireless to the existing router.. the ethernet ports go off.. there is no wifi from the TC to the rest of the network..it is just a client. And you will double hop the wireless which means half the speed.
Test it yourself.. that is the best way to learn. Hold down the option key and select wireless mode.. join will then be available.. although you may have to use 5.6 airport utility to do it.
The exception to this is if the main router is another apple model.. then the TC can use extend wireless.. but I am guessing that you have a wireless modem router not an airport extreme etc.

I am setting up time capsule and have issues with DNS

Can't get internet connected and says DNS server not identified

Technicolor TG789vn is a gateway, which is a modem and router in one package. Please verify by checking the Technicolor information on this model below:
http:///en/solutions-services/connected-home/modems-gateways/xdsl-modems-gateway s/tg789vn-bonded
Assuming that things are working correctly, AirPort Utility should be able to set up the Time Capsule correctly with this type of device.
Shut down your Mac and then restart the device.
Power off the Technicolor gateway, wait a minute, then power it back up and let it run a few minutes.
Power up the Time Capsule for a few minutes, then hold in the reset button on the back of the Time Capsule for 8-10 seconds and release. Allow a full minute for the Time Capsule to restart to a slow, blinking amber light status.
Connect an Ethernet cable....that you have tested to make sure that it is working....from one of the LAN <--> ports on the Technicolor gateway to the WAN "O" port on the Time Capsule
On your Mac....open Macintosh HD > Applications > Utilities > AIrPort Utility
Click on Other WiFi Devices
Click on Time Capsule
The setup utility will open up with a configuration window mentioning that the Time Capsule will be set up to create a network
For Network Name......Enter a simple, short name that you want to call your wireless network.
For Base Station.......Enter a simple, short name that you want to call the Time Capsule. Mine is TC, for example
For Password.........Enter a password that will be used for the wireless network and base station
For Verify Password.....Enter the same password to confirm
Click Next
The utility will set up everything for you. When you see the message of Setup Complete, click Done and you should have a green light on the Time Capsule.
Select the wireless network that you created and enter the password to connect. You should be all set.

How do i set my time capsule up to function as an external hard drive

How do i set my time capsule up to function as an external hard drive? Is this even possible? I had a friend tell me it woudl be a good set up to get a time capsule with my Macbook Air to use as a gigantic external hard drive but then was unbale to wlak me through the setup after I bought the equipment. Any suggestions?

It depends on what you already have equipment wise..
Just bridge the TC..
I cannot walk you through it either if you use v6 airport utility.. due to my refusing to run Lion until it gets network issues sorted.
Download and run the real utility http://support.apple.com/kb/DL1482
Go to manual setup..
Internet tab
Connection sharing.. select off bridge mode in the drop down box.
You can then if you like turn off wireless under airport wireless.. The TC is now a plain network client with hard disk.
Personally I would keep the wireless on but sort the channels manually if you already have a wireless AP or router.

Having trouble setting up Time capsule...

I just bought a new iMac last night. I also picked up Time Capsule and Apple TV. I'm having a problem setting up Time Capsule correctly. I'll go through what I did step by step and hopefully someone can help me as I've never tried to set up a wireless network before.
I'm connected to the internet via Comcast. I have the outside cable coming into the modem and the ethernet cable from the modem i have plugged into TC's WAN port (the one with the gear logo).
I start by opening Airport Utility ( I upgraded to the most recent version using the install disc that came with TC) and it recognizes TC in the left side of the window. It says it found TC with default settings and gives a name for it and an Airport ID. I click continue.
The next window prompts me to name the TC and assign a password. I do so and click continue.
The next window gives me some options about setting up a new or existing wireless network. It says it found some existing networks which I assume are my neighbors. I select "I don't have a wireless network and want to create one". I click continue.
The next window prompts me to give a name and security level to the new network. I provide a name and select WPA/WPA2 Personal and enter and verify a password. I click continue.
The next window asks whether I'd like TC to be in Bridge mode or Share a single IP address using DHCP and NAT.
If I click Share a single IP, a popup tells me "This will cause my TC to continue to blink amber and do I want to ignore this and continue?". So I figure this can't be a good thing and I click on Bridge mode not really knowing what it means.
The next window asks me to enter the TCP/IP info from my ISP. It also says to choose "Using DHCP" if I receive an IP address automatically. So in the box where it says "Configure IPv4", I select "Using DHCP" and there is an IP address and Subnet mask with numbers after each. Below that is Router Address, with fields for DNS Server, Domain Name and DHCP Client ID. These fields are blank. I click continue.
The next window says TC will use these settings:
TC name - Jim's Time Capsule
Wireless Mode - Create a wireless network
Network Name - Jim's Network
Wireless Security - WPA/WPA2 Personal
Connect Using - Ethernet
Configure IPv4 - Using DHCP
IP Address - (Provided Automatically)
If settings are correct, click Update to finish setting up your TC or click Go Back to change settings. I click Update and a box tells me that the device and its network service will be temporarily unavailable and do I want to continue? I click continue.
The next window tells me that the settings for TC have been updated successfully and its being configured. I then get a window reporting a problem.It says-
"Problem 1 of 1: Internet Connection
Your Apple wireless device does not have a valid IP address. Make sure your Apple wireless device is connected to your broadband modem or local network, verify your settings and try again. If you still can't connect, call your ISP."
There are two boxes with options. The first is "Connect Using" and "ethernet" is selected with "PPoE" being the other option. The second box says "Configure IPv4" and "Using DHCP" is selected, and "Manually" is the other option.
Obviously, I'm doing something wrong, but I don't have a clue. I'm getting online fine when I plug the ethernet cable into the back of the iMac. I've reset the modem by hitting the reset button. The light turns green on the TC but I can't connect to the internet. Any ideas? Feel free to call me a big dummy
Jim

Thank you, Jim Somoygi. I had a similar multi-hour odyssey with a AE and a Comcast cable modem.
This solved the seemingly endless blinking amber light:
1. unplug power from the modem and AE (or time capsule). Go get a beverage of your choice (wait a couple of minutes).
2. My modem has a battery backup (Comcast phone service). So, I pressed a tiny reset button on the back of the Comcast modem (it's made by Arris). With the battery backup, I'm not sure I would have been able to reset the modem simply by unplugging.
3. Make sure there is an ethernet cable connecting the cable modem and the AE or TC
4. Plug the modem back in, wait for the lights to come on. I also had to press a "standby" button on the front of the modem to get all the lights to come on.
5. Plug in the AE (or TC)
6. Green light on the AE (it's not easy being green)
7. Choose the appropriate Airport network & surf away.
I will say that the problem seems to be with the modem, rather than the AE. Once I reset the modem, I could configure the AE with ease. Once the AE is configured, it is absolutely rock stable. Before I fiddled with the network & brought this on myself, I enjoyed shockingly stable networking with the AE -- much better than with previous attempts with Netgear or Buffalo products (although I do like the ease with which Buffalo products can be configured together, using their proprietary handshaking protocol "AOSS").

HOW TO SET UP time capsule with time machine?

I have not been successful in setting up time capsule with the time machine,can someone give me steps to follow?

What part are you having problems with? You need to make sure File Sharing is enabled on the Time Capsule (which is done in AirPort Utility). Then you just connect to the Time Capsule either wirelessly or via ethernet cable and when you go to Time Machine setup your computer should recognize your Time Capsule as a valid storage for Time Machine backups.

How to set up time capsule with BT Infinity

how to set up time capsule with BT Infinity

The easiest and sure way is to use bridge on the TC as the method of connection. The TC then becomes a device in your network and gets its IP from the main router that I presume BT supply.
Method is,
1. Plug the TC WAN port into the BT supplied modem by ethernet.
2. Plug the computer you are using for the setup into the TC by ethernet.
3. Run the airport utility .. go to internet tab on the top menu..
In the bottom option, Connection Sharing choose off (bridged mode)
4. Go to the wireless page and setup wireless connection as you like it.. using whichever band you want. And make sure security is set to the highest setting, wpa2 personal. Put in a decent wireless passkey.
5. Press the update and fix whatever else the TC will show as needing fixing.. usually security stuff.
6. You can then disconnect the ethernet and connect by wireless if you want. Any port on the TC will now be a LAN port, including WAN.
This is assuming BT supply a wireless router with built in vdsl/other type of modem. If so you normally will not be able to bridge the modem, unless BT are using pppoe authentication which they haven't in the past.
If you really need to use the TC as a router then you will need to work out an alternative method. You can double NAT by placing the TC in the DMZ of the BT router if that is an option. It is not without issues in general.

How can I set my time capsule to back-up only once a day?

How can I set my time capsule to only back-up once a day. It appears to be backing up several times a day. Not sure there is a set schedule for the back-ups and they take a great deal of time; over an hour each.

tdenny2 wrote:
Not sure there is a set schedule for the back-ups and they take a great deal of time; over an hour each.
Then something is wrong. Changing the schedule will only deal with the symptom (and give up one of the better features of Time Machine's usually quick and unobtrusive hourly backups).
See if the size of the backups makes sense, considering what you've changed since the previous one. If it seems much too large, that may be the problem. See #D4 in Time Machine - Troubleshooting for some common culprits and ways to see just what's going on.
If the sizes seem reasonable, see #D2 in the same link for things that can cause extra-slow backups.

My macbook pro is connected to internet via my time capsule but my iPad and iPhone won't. it shows wifi connection to the time capsule but when i go on to the internet on the iPad or iPhone, it comes up with network error. can anyone help?

my macbook pro is connected to internet via my time capsule but my iPad and iPhone won't. it shows wifi connection to the time capsule but when i go on to the internet on the iPad or iPhone, it comes up with network error. can anyone help?

This can be caused by a number of issues.
Was everything working and then suddenly stopped??
Or is this a new clean setup and has never worked.
Do you have a cable modem which is not a router and the TC setup in bridge? That will cause it. The TC must be in router mode, ie dhcp and nat.
Check the IP the MBP gets including dns and gateway..
Then check the ipad/iphone.. post what IP dns and gateway (router in applespeak) they get.

Setting up Time Capsule for backup only on existing wireless network

I have a wireless network already set up with a NetGear wireless router. Cable plugs into router, router connected via ethernet cable to my Power Mac G5 desktop, plus 2 PC laptops in the house also connect wirelessly to the home network via this router.
I want to set up Time Capsule as an external hard drive to back up all three computers -- I don't necessarily need to use it as a wireless router although i'm not opposed to that if it's easier to do it that way.
When i try to set it up using AirPort utility, i get the amber flashing light. Airport utility is able to discover the device, and then always asks if it's OK to switch networks. I've tried both "switch" and "don't switch"; either way when i try to set it up, AirPort utility stalls out on "Reading Time Capsule Configuration"; eventually giving me the error msg: "Base Station Error: AirPort Utility was unable to find your Apple wireless device."
All i want to do is mount it as an external hard drive so i can use Time Machine for backup, and be able to use it to also back up the PC laptops wirelessly. I need help in the following three areas:
1. How should I be physically connecting my devices if i want to do this? Which cables go in which ports? There is only one ethernet port on the back of my G5. The G5 can connect to the router either wirelessly OR via ethernet cable. I've tried G5-->Time Capsule-->Router, G5-->Router-->Time Capsule, Router-->G5 PLUS Router-->Time Capsule, and I've tried every variation on the regular ethernet and WAN ports. What's the right way to do this.
2. If i'm not setting up the TC as a Wireless Router, is AirPort utility even the right tool for setting it up? it seems to be confused by the two wireless networks and won't let me get past that point. Am I supposed to click "Switch" when it asks me to switch networks? Is there a way to just mount it as an external drive and bypass the AirPort utility setup entirely?
3. Once i get it set up so it's visible as an external drive and usable for Time Machine backup, how do i then make it available to the other PCs on the network so they can back up to it also?
Thanks for your help.

sarah,
You already have an existing wireless network.
You do not need to plug the Time Capsule into anything except power.
Set the Time Capsule to "Join an existing wireless network"...
That is all you need to do.
Then all the computers should see the Time Capsule.
If you can't see "Join an existing wireless network" in the choices, hold down on the option key and then click on the choices.
Give that a try.

Set up time capsule as wireless access point

I am trying to set up my old apple time capsule as a wireless access point for my girlfriend. She is at college and the university does not permit routers, so I am trying to set the time capsule up so that is just takes the hardwired internet and allows wireless access to the internet so she can use her iPad and MacBook Air on the wireless instead of having to use a gigabit adapter to use the ethernet. The time capsule has the newest firmware and she is running mavericks which has the newest airport utility software. However I am not sure what settings to use to make this work. I am fairly intelligent when it comes to computers however I am not very skilled in networking. If anyone can help I would greatly appreciate it.
Thank you in advance!

How old is the Time Capsule? Running what firmware?
You have a problem.. If you cannot use the TC in router mode, then you are going to have to use it in bridge.. and it then depends on if the Uni system will hand out mulitple IP addresses. .which I doubt. In the end you might be stuck.. and it is not possible really with any system..
Bridge normally requires that the TC take an IP address and then clients connecting to the TC wireless will also get IP addresses.. but if the uni system only hands out one address then the TC has already captured it and there are no more available.. but try that method first.. as it is the easiest.
If it fails there is a more complicated method.. where we can give the TC a separate static IP in a different IP range and the wireless will still be bridged.. so the MBA or the ipad can use the wireless.. but only one can ever be online at a time.
The only way around this is to use the TC as a router contra the rules in the uni.. although I would suggest the uni only cares if you break their system. Most people don't.. but I am unsure what happens if you do.
Ask their IT people how to use a wireless only device like ipad, when they only provide ethernet. You might find there already is a wireless internet system as well.

HT1178 wifi to set up time capsule

Similar Messages

Maybe you are looking for