HT3964 My MacBook pro starts to come on with apple sign and turning wheel but does not go past that
Please help urgently
Sojiwoye wrote:
Thank you. I used the command and R buttons and tried reinstalling Os with disk supplied because Internet speed very slow to reinstall from Internet here. With CD inside it is showing the apple logo and then three beep sounds in succession and not going further
That is becaause the disc you are using is for an older version of OS X, more then likely Snow Leopard, and will not install because you are now running a newer version of OS X, Lion.
Your only option is to download Lion frim the internet to re-install it or buy the Lion install USB thumb drive from Apple.
Similar Messages
-
My macbook pro 2011 shows grey screen with apple logo and want start
i was just using my macbook pro and it freezed for a while not responding and i turned it off by pressing the power button. afterwards, i turn it on and it shows a grey screen with apple logo but want start pls somebody help me because am having "my life" on the machine
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.a. Boot into Recovery by holding down the key combination command-R at the startup chime, or from a local Time Machine backup volume (option key at startup.) Release the keys when you see a gray screen with a spinning dial. When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire or Thunderbolt cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode.* The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
*Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Post for further instructions.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Boot into Recovery again. When the OS X Utilities screen appears, follow the prompts to reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
Step 8
A dead logic-board battery in a Mac Pro can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested. -
My MacBook Pro will receive emails, yet the text is missing in all of them. Any ideas?
Try rebuilding the mailbox. This can take awhile if you have a lot of mail.
Rebuild mailbox -
Any help!!!
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 7
Repeat Step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 8
This step applies only to older Macs (not current models) that have a logic-board ("PRAM") battery. Both desktop and portable Macs used to have such a battery. The logic-board battery is separate from the main battery of a portable. A dead logic-board battery can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested. If you can't get to an Apple Store, go to another authorized service provider. -
Macbook Pro starts up, has a small loading bar, and then shuts off.
Macbook Pro starts up, has a small loading bar, and then shuts off after a few seconds, but the Windows bootcamp partition works fine.
The repair disc option (using install disc) failed, and the computer cannot locate the original Mac side partition. Only Bootcamp appears under options to "restore from backup" or reinstall. The repair disc options says it should be repaired but doesn't seem to know how.
Macbook Pro.
Snow leaopard
Bootcamped with Windows.
Any ideas?Hold c or option key and boot off the 10.6 installer disk, run DU Repair from there.
run through this list of fixes 1-8
Step by Step to fix your Mac
If it doens't work, you can recover files if you don't have any current OS X file backups, then grab what you can out of Bootcamp
Use Data Rescue installed on the extenral boot drive ($100) to read the bits of the internal (non-filevaulted) drive to retrieve OS X data files if you can't get them off manually via drag and drop methods.
Create a data recovery, undelete boot drive
If you want to clone Windows, use WinClone and another drive. However it's likely compromised, unless it something you did in Windows, like trying to create a new parttition perhaps?
Then perform a Zero Erase and install of 10.6 as shown here (on the entire drive, not only the parittions), this will give a new GUID partition table, EFI and map off bad sectors, totally fresh everything.
How to erase and install Snow Leopard 10.6
You cna use Carbon Copy Cloner to clone the new extenral setup to the new scrubbed internal drive. Recreate Bootcamp and WinClone back or fresh install Windows into Bootcamp like before. OR opt to use virtual machine software which is safer.
Windows in BootCamp or Virtual Machine?
Windows 7 can write to the boot drives GUID partition map (unlike XP), this is likely why it's borked now. -
My MacBook Pro pwers up but does not get past the the Apple logo.
I have a MacBook Pro with Mountain Lion. It powers up but does not get past the Apple logo. The hardware test did not reveal any problems. It will also not get any further when I try to start up in Safe Mode. The last thing I was trying to do was connect to it from my desktop which I have done before. Any ideas.
I was able to get into the Repair utility and resolved some Permissions problems. It verified the disk and found no problems. However, it did not resolve the issue. I was also not able to get into Safe Mode.
-
Prints fine with other browsers and programs. Works with my wife's MacBook Pro.
Took it to Apple Genius, they told me it was my memory (incompatible)
Believe the first one. No one RAM test will reliably indicate RAM is bad. Once indicated, it has to be replaced.
You have to get RAM made for the mid 2012 13" MacBook Pro. Just because it says it 4GB of 1600MHz DDR3 memory does not mean it is compatible with your Mac. You have to buy RAM for Macs with lifetime warranty, that is not ValueRAM, and says the model and its time frame within the year that it was released, and its model number when buying RAM. Both http://www.macsales.com/ (OWC) and http://www.crucial.com/ sell RAM in that means of attributing what kind of RAM it is.
I ran an internet-based free diagnostic tool and it showed that my hard drive did have bad parts (corrupted? possible to fix or not?) and it was acting irregularly...
What tool? Some are known to damage software components of drives. Especially any that address system cache. -
My macbook pro doesn't bootbeyond the grey screen with apple icon and spinning wheel.
My macbook pro doesn't boot beyond the grey screen with apple icon and spinning wheel. I used the "Option" button to access the Disk Utility function and run Repair Disk and Repair Disk Permissions. Should I restart my computer?
The following support article is somewhat outdated. Where it refers to booting from an installation disc, you should boot from your recovery partition (if running 10.7 or later) by holding down the key combination command-R at the chime.
Mac OS X: Gray screen appears during startup -
Macbook Pro (2011) froze while working, forced shut down, now won't turn on. Grey screen with apple logo and spinning wheel for hours. Help?
Unfortunately do not know the operating system since I never updated anything and I can't get in to it.
Thanks for your assistance.If you want to preserve the data on the boot drive, and it's not already backed up, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data, you can skip this step.
There are several ways to back up a Mac that is not fully functional. You need an external hard drive to hold the backup data.
1. Boot from the Recovery partition or from a local Time Machine backup volume (option key at startup.) Launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
2. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
3. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data. -
My MacBook Pro recognizes which of my three printers is plugged in (USB), but can it automatically use that printer or do I have to select that printer from the list each time I switch between printers?
My MacBook Pro recognizes which of my three printers is plugged in (USB), but can it automatically use that printer or do I have to select that printer from the list each time I switch between printers?
-
MacBook will not start. I have restarted with original CD. I have used Utilities and "no problem" with hard drive. I have reset PRAM. I have tried safe boot. Nothing is work. Gray screen with Apple logo and rotating wheel. Thanks for any suggestions!
Snow Leopard is a Mac OS X version. You say that it's the version you have in your Mac (10.6.8). Do a back up of your files, format the hard drive (using Disk Utility) and reinstall again
-
I have a MacBook Pro. When I go to system preferences, the external speakers option does not appear on the input tab and, of course, the external speakers do not work. Help?
When you plug headphones in, or external speakers, where it states "internal speakers", it will rename that "headphones", say. Unless you are running an external sound card.
-
When turning on my mac book pro it displays a screen with apple logo and begins loading a loading bar, after this continues to show loading circle however has been like this all day still no different. Tried turning it on and off however still same!
... then run Disk Utility, Repair Disk.
Also:
Resolve startup issues and perform disk maintenance with Disk ...
Mac troubleshooting FAQ: start-up woes
How To Fix Common Mac Startup Problems
Mac Stalls on Gray Screen at Startup - Troubleshooting Mac Startup ... -
I cannot start my mac book. Apple logo and spinning wheel on gray screen. Tried pressing shift key on start up nothing happen. Tried shift+command+V screen is still stuck
Reinstall OS X without erasing the drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.
=======================================
Reinstall - Mavericks, Lion/Mountain Lion
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported then click on the Repair Permissions button. When the process is completed, then quit DU and return to the main menu. Select Restart from the Apple menu.
Reinstall Mountain Lion or Mavericks
OS X Mavericks- Reinstall OS X
OS X Mountain Lion- Reinstall OS X
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is
three times faster than wireless. -
Hi my serial number on bottom of my mac is W8******66E when l try to turn the computer on it is just going to grey screen with apple logo and spinning wheel i have tried starting in safe mode and a few other suggested solutions and they have not worked?
<Edited by Host>What other solutions have you tried?
This may help you:
https://discussions.apple.com/docs/DOC-3353
Ciao.
Maybe you are looking for
-
Help plz
-
Adding an attachment to a BPEL process instance
Hi Is it possible to add an attachment (say a word/pdf doc) to an instance, where the document is obtained from a webservice (say as a binary content in web service)? Thanks SAtinder
-
Hi All, My requirement is I have a XML file, its data should be stored in Database. Below is the sample XML file. <?xml version="1.0"?> <PaymentInfoMessageResponse> <PaymentInfoResponse> <TransactionType>940</TransactionType> <SequenceNum>04</Sequenc
-
Pos1, side up, side down doesn´t work
when activating Extras --> settings --> advanced --> allow marking of text the buttons pos1 page up / down are not activated. == This happened == Every time Firefox opened == Extras --> settings --> advanced --> allow marking of text
-
Dear All Expert, I have a requirement is :To fetch the data from CO Tables (COBK, COEP), and on basis of that display the FI and MM data (from BSEG and MSEG),eliminating the reversed documents. Now my problem is how to eliminate MM reversal document