画質.音質が一番DVD用のmpegエンコード方法

windows 2000、でpremiere 6.5を使ってます。
adobe mpeg encoderで、DVD用にムービーをMPEG2に変換しています。
現在ビデオのビットレートを８MBPS（固定ビットレート）、オーディオのタイプをPCM,マルチプレクスタイプをDVD（ビットレート固定、10.8mbps、最大ファイルサイズ・オフ）に しています。この状態で書き出すと、映像はきれいなのですが、音に「プチプチ」といったノイズがのってしまいます。
画質、音質ともに一番良い状態で、なおかつ一般的なDVDプレイヤーの再生に耐えられる設定はどのようにすればよいのでしょうか？
どなたか御教授ください。宜しくお願い致します。

＞この状態で書き出すと、映像はきれいなのですが、音に「プチプチ」といったノイズがのってしまいます。
他のビットレートではノイズは乗らないのですか？もし乗るのなら設定のせいではなく、ハードウエアの問題です。これはソフトの設定では直りません。
＞画質、音質ともに一番良い状態で、なおかつ一般的なDVDプレイヤーの再生に耐えられる設定はどのようにすればよいのでしょうか？
使用するDVD-Rメディアが4.7GBですと、DVD-VIDEO形式では全部使えませんので、再生時間によってトータルのビットレートを決めれば良いと思います。120分で4.5Mbps ・100分で5Mbps・80分で80分で6Mbps・60分で9Mbpsくらいです。
またソースの画像によって使用するビットレートを高くしても無意味な事があります。アナログVIDEOですとS-VHSで6Mbpsくらいです。
なお、Adobe MPEG ENCORDERのエンコード性能はそれほど高くありません。6.5でしたらCCE BASICの様なPremiereのプラグインに使える高性能エンコーダを使った方がよりよい結果が出ると思います。マシンパワーが十分なら実再生時間の2/3くらいでエンコードが可能です 。
史

Similar Messages

  • Is there a difference between Audigy 2 hardware decoding and DVD/MPEG-2 software decodi

    I have a capture card and run my PC as a part time HTPC. The audio and video is analog captured and MPEG-2 encoded by the card.
    I have the Nvidia DVD/MPEG-2 decoder set to SPDIF(reciever) so it sends the audio stream directly to the Audigy 2.
    When playing any of these recorded shows, the only way I get any surround sound on my 5. speakers is to have CMSS () turned on, and it's ok (but not as good as true DVD quality 5.).
    What I am wondering, would there be any difference if I upgraded the Nvidia codec to the platinum version, which does software 5. decoding? Would it do a better job of decoding any Dolby Surround material?

    http://www.bulletsandbones.com/GB/GBFAQ.html#neverfail

  • Color Correction + DVD/MPEG Compression Produced Noise

    I recently color corrected a 3-hour rock concert using FCP and a broadcast monitor. When played from the timeline the concert looks great however after outputting, MPEG compression and authoring a DVD there's video noise over the image. Almost snow like but different. I'd post a screengrab but I can't seem to take one in DVD Player. Any advice?

    That's exactly right Jonathan, you need to add the 2:3 pulldown, and I can tell you all why. (I read the post from Max Average, but I'm not commenting that separately)
    The DVD specification simply does not support video marked as 23.98 fps (which is how Apple wants to call it) or even 23.976 fps (which is what MPEG-2 calls it). This means that for NTSC DVDs you can only use MPEG-2 video files which are marked as 29.97 fps. This is true whether your encoder (like Compressor) is letting you be aware of it or not. There is no "native 23.98 frame rate" on a DVD and the right way of making the decoder believe it is 29.97 instead, is to use 2:3 pulldown. Any other method would just be wasting bandwidth/bitrate or picture quality, depending on which way you want to look at it.
    The 2:3 pulldown process, as specified by MPEG-2, is a way for the encoder of describing to the decoder which of its already decoded fields it should be repeating (displaying once more) and when. These field repetitions are designed to increase the interlaced displayed frame rate from 23.976 to 29.97. This "new" frame rate must be explicitely written into the .m2v stream, to be accepted by a DVD authoring tool, e.g., DVD SP.
    I am sure many of you may wonder why it is called "pulldown" when in fact the frame rate seems to be going "up" from 24 to 30, as I did myself back in the nineties;-)
    The way to wrap ones head around that, is to think about what whould happen if you just mapped 24 FPS film frames onto the NTSC TV standard which has to display frames at nearly 30 fps on a TV. Of course the movie would run 25% FASTER on a TV than it did at the cinema/picture theatre. In that perspective, the solution had to be to SLOW DOWN (pulldown) the presentation speed on a TV. The engineers of that time (this was long before color TV was even invented)
    were faced with a need for film (Hollywood movies) to be translated for TV broadcasts). Of course they could not change the 30 fps used for TV broadcasts (29.97 fps came much later when colors were added;-), so they had to come up with a scheme which made each film frame seem to last 25% longer on the TV screen, than it would have otherwise. "Pulling down" the display frequency from, the physical 30 fps to match the experienced 24 fps was accomplished by letting every other frame be displayed for 50% longer on the TV. On average that is of course 25% longer (slower) which was the goal.
    I may be monitoring this thread for further comments.
    BTW, BitVice 1.7 runs surprisingly well under Rosetta.
    Roger Andersson / Innobits AB, Makers of BitVice MPEG-2 Encoder for Mac
    http://www.innobits.com/
    As per Apple Discussions Terms of Service:
    "I may receive some form of compensation, financial or otherwise, from my recommendation or link."

  • DVD - MPEG 4 sound issue

    On my Powerbook G4 running OSX Panther, I just encoded a peice of video taken from a DVD -r I burned using my Panasonic DVD recording deck. Handbreak did the job, but I have noticed that during playback on my iPod there is a split second break in sound approximately every 30 secs. I'm not a genious when it comes to sound, but I know a little and think it may be to do with the sample rate on the DVD being different to the re-encoded sample rate of Handbreak thus becoming out of sync and cross phasing at 30 second intervals. The DVD plays fine, its just the encoded H.264 file that doesn't. Video remains fine. Any feed back would be great.
    Thanks

    Choose the AAC audio codec from the list of options. There is no audio codec called "MPEG-4". AAC is the MPEG-4 "standard" for audio.
    MPEG-4 was adopted as an industry standard in 1998 (I believe). It was made available for QuickTime use in 2002 with the introduction of version 6.
    Prior to AAC many files used MPEG-1 layer 3 (.mp3) for audio only files and QDesign Music 2 or the older IMA 4:1 (at lower frequencies) for .mov files.
    I continue to use QDesign Music 2 because it makes very small file sized audio tracks. Up to 5 times smaller than a similar .mp3 file.

  • Problem: Importing from DVD to imovie. The DVD mpeg 4 file will not import

    I recently purchased ImTOO DVD Ripper Ultimate. I've successfully managed to rip some files to my desktop. But I'm now having an issue importing 1 particular mpeg 4 file to imovie for editing. I open imovie and locate the mpeg 4 file. Imovie window pops up: Optimizing Video - Processing Event. Nothing happens. Any advice?

    First advice: let it run. it may take a while.
    Second advice: Check for extra tracks like tween tracks, closed captioning tracks, chapter tracks. iMovie will not import files that have these. It is best to remove these using QuickTime Pro before editing.

  • HD source encoding into SD DVD MPEG-2 format desaturates film

    I am encoding a 720P HD source from FCP, the source is the Prores (HQ) format. I encode to MPEG-2 in Compressor. When I view the Standard def DVD the colors are really desaturated. There is no way to increase saturation in Compressor from what I can see. Any suggestions?
    Message was edited by: Miklos

    This is almost certainly a gamma issue. This isn't specific to your HD source.
    Very commonly this is an issue with monitor calibration and Final Cut Pro's "special" handling of gamma. Here is a really, really brief summary of what's going on.
    So you have all of this video that was recorded with a Gamma of 2.2. Final Cut Pro opens this video, silently converts it to Gamma 1.8 for display purposes, and shows it to you. Why? Because Macintosh has had a default display Gamma of 1.8 since the Reagan administration or so. The original data doesn't change, but Final Cut magically adjusts the video it actually displays to Gamma 1.8, so it looks about right on your default-setting, default-brightness, default-everything Mac monitor.
    But wait! You've got a monitor that is calibrated at a Gamma setting other than 1.8. You've either calibrated it yourself, or you've loaded a color profile (in System Preferences->Display) that isn't a Gamma 1.8 profile. Final Cut Pro is spitting out Gamma 1.8 video, but you're not seeing it. You're seeing something completely different.
    But this is a Mac! We've got ColorSync! This shouldn't happen! Bzzt. Final Cut bypasses ColorSync when making this decision. See this url:
    http://docs.info.apple.com/article.html?artnum=93794-fr
    Note this very, very, very important quote:
    Tip: While it is possible to recalibrate Apple displays via the Display Calibrator Assistant in Displays preferences, users should leave the gamma of their monitors to the 1.8 Standard Gamma setting when working in Final Cut Pro. ColorSync settings are not used by either Shake or Final Cut Pro for automatic color calibration or compensation of any kind.
    I have an entire rant about this that we will save for another time.
    So you're looking at what is for all intents and purposes, the "wrong" color. you go on and color correct your footage, or otherwise alter it, all the while making it look good on your monitor. Unfortunately, all of the changes you're making are being done so that the video you are SEEING looks good, but you're not seeing the ACTUAL video, you're seeing an "incorrectly" gamma-adjusted video. The minute that video leaves the Final Cut world on your system, and is displayed on a monitor with a "correct" Gamma of 2.2, you're going to see the "correct" video, which is going to look either too light or too dark, depending on your current display profile when you modified the video.
    But you have no way of knowing this. So you use Compressor to make an MPEG-2 file, and Compressor dutifully takes the actual video data (the data that you're not seeing) and makes the MPEG file. You burn the DVD.
    You put the DVD into your DVD player, and everything is either washed out or too dark.
    So how do you resolve the issue?
    1. You must have a trusted video path out to trusted scopes out to a trusted, calibrated display device. Most obviously, this means SDI or HD-SDI out to a calibrated monitor. There are plenty of other options, but this is the standard.
    2. Trust the broadcast monitor, trust the scopes, and completely forget what you see in Final Cut Pro. It doesn't exist. It's imaginary. If Final Cut shows you a totally black image but you can see rainbows in the broadcast monitor, you're going to get rainbows when you go out to DVD.
    3. If you can't afford or don't have access to a monitor intended for grading, and you just need to do -something-, use a Spyder3 or other device to calibrate your computer's monitor with a target Gamma of 1.8. Your color space is still not going to match Rec 709 or 601 or so on, but you'll be in a ballpark that you can probably get away with for web video, personal/family stuff, etc. Never, ever do this for anything going out to broadcast television or any actual critical evaluation situation, but this will suffice for producing simple web content.
    If you're making DVDs that are actually going to be on the market or outside of your friends and family, you -really- need to have a calibrated monitor that is capable of displaying the native color space of the output you desire.
    On a more technical level, there is also a standing concern that there is a color space/matrix issue occuring when ProRes is decoded during the act of Compressor reading in the video data from Quicktime. We've seen evidence of this here, but we're still investigating.
    In any event, it's late, and that's the very, very short and condensed version of my "What's broken about Gamma handling in Final Cut Studio" rant.
    -Matt

  • Which tool can convert DVD(MPEG-2) video stream to MPEG-4?

    And how about sound? Any free format comparable to Xdiv?

    yeh - xvid is an open-source fork of divx, and the quality is meant to better than divx4 at least, although I can't tell the difference.
    mencoder is an excellent tool for doing almost anything with video - and the docs are great too...
    http://www.mplayerhq.hu/DOCS/HTML-singl … -dvd-mpeg4

  • Choppy dvd/mpegs RS482M4 motherboard

    Newbie here, first puter I have built in about 5 years. Boy have things changed LOL. Using the RS482M4 motherboard, AMD3000 CPU and 1 gig Corsair memory Enermax'disco' case w/ 350w power supply.(for now) windowsXPsp2 OS.
    Only have two real issues.
    1. front headphone jack cant get to work (not a real big deal), this is for my 11yr old who doesnt use them anyway
    2. video is choppy, and if I drag an open window quickly across the screen it kind of leaves a 'trail' (and yes I am sober when I am doing this)
    I assigned 256m of the memory to the video in the bios, made it very marginally better. Is there a driver I should install from the disc or ????
    I have used this board for troubleshooting help (search function rocks  ) and figured i would stop lurkin and say hi....
    sam

    Depends on how you want to use it?  If you are planning on outputting to StandardTV via TV out & using it only for video/media playback & basic business apps, go with Nvidia -they have superior TVout quality, according to those in the know. The 6600 vanilla 128mb ram (non-GT model) is pretty good as they supply an HDTV component/composite adaptor for futureproofing & designed for use with Nvidia's Purevideo codecs (if you want to get that extensive). I have the MSI NX660LE in my HTPC. Not sure if there is an issue with using it in conjunction with my X1 projector. Am in the process of trying to sort it out. If you're in the States I'd go with the vanilla model for the cost.
    If you are planning on a multi-useage including some gaming, I'd go with a 256mb GT model. A great source of info is www.htpcnews.com it has it's own sub-section on video cards.

  • Cleaner 6 Mpegs seems to crash DVD Studio Pro 4

    I have slow motion clips that DVD Studio Pro can't seem to encode properly, I get lots of strobbing when played back on a regular monitor. I began an experiment with Cleaner which involved rendering a small QT movie with every DVD mpeg 2 setting, with the exception of 16x9 and Pal. I then import these into a new project and the second I lay one of these files onto a track I get the never ending spinning beach ball. Anyone know why this would happen?
    Tried on laptop running Panther and G5 running Tiger.

    Hi Byron,
    Welcome to the forum.
    I take you have experimented with the filters in compressor!
    My suggestion would be to do the slow mo work in something like FCP and get the uncompressed quicktime file the way you like it. Then encode using Compressor.
    Cleaners mpegs have always been of poor quality (visually that is). I am surprisedd that its output is not MP@ML though.

  • CS4: DVD encoding problem(s) Mpeg2 and avi

    Hi,
    I have been trying to burn my video files to DVD. After a month of failures and 50+ wasted DVDs thrown in the garbage -- plus countless hours trying to learn the basics, reading the FAQs, trouble-shooting, and losing my patience awaiting technical replies from Adobe (which I now suspect will go unanswered) -- I am out of solutions and waving a white flag.
    Problem:
    I have two video files. Both were created in Premiere Pro CS4 and exported via the Adobe Media Encoder as MPEG2-DVD high quality files (for NTSC) .
    The first Mpeg2 file is 800 MB (41 mins); the other is 988 MB (50 mins).
    I have placed the two files into a single timeline, with 21 chapter stops.
    The only other file in the entire project is a PSD file for the Menu. It has two buttons, which link respectively to chapter stops 1 and 10.
    My results are failure-upon-failure...
    Primary question:
    When I go to "Build" the DVD, it says the Encoded Size is 4.7 GB ~ same size as the DVD. This displays in the "Disc Info".
    Similarly, when I open my "Timeline" properties for that single timeline, it says the duration is 1 hour 31 minutes - 4.7 GB.
    Why is the disc a full 4.7 GB when the two video files (combined) are under 2 GB?
    Supplementary questions:
    My "Flowchart" and "Property" links display the Menu, with the two button links in my Menu PSD connecting to the respective chapter stops.
    There are no problems when I click "Check Project," and the project works perfectly in "Preview" mode.
    But, when I attempt to test the burned DVD into different DVD players, the Menu doesn't appear and the play defaults to random chapters, then freezes. I can access the menu, but only after the play has started and/or frozen, and I have to do that by clicking the "Menu" button on my DVD remotes. And again, when I hit play on either of the buttons on the main menu, the video files will freeze, which means burning & testing each disc sometimes takes an hour per.
    Does anybody have a solution?
    I have read and watched several tutorials, to no avail. I have tried burning the Project using large Mpeg files as well as medium Mpeg files, both encoded with 1-Pass VBR, 2-pass VBR, CBR. I have tried widescreen and normal.
    I have also tried using AVI files. The two AVI files are respectively 41 mins @ 1536 kbps 720x480 8.68GB; and 50 mins @ 1536 kbps 720x480 10.6GB.
    Together, those two AVI files are 19+ GB, which would require 5 DVDs.
    What am I doing wrong? What should I be using to burn DVDs - Mpeg-2 or Avis?
    When I export from Premiere Pro/Adobe Media Encoder, whould I be exporting as Mpeg2 files or Mpeg2-DVD?
    Is it possible that Encore automatically expand and/or compress files, so that the 19GB avi is compressed to 4.7 GB DVD; and the 1.8 GB Mpeg2 "expands" to 4.7 GB?
    Any help would be greatly appreciated, as this project has caused me numerous delays and ruined deadlines and soured me even more on Adobe's video editing product and their truly-awful customer support.
    Thank you

    As far as the use of premiere pro CS4 with Encore Cs4, do not bother to pre transcode your material.  Let Encore do this for you.  Leave your files in the original format which I assume was AVI.  Instead import your Premiere Pro sequence directly from the project (or export it from Premiere Pro it to encore).   As you quessed Encore will try and expand/compress your files for the DVD you are making.
    Encore by default trys to transcode for the best quality that will fit onto the media you specify which is why it is setting the output to 4.7 rather than the file size of the video.
    You were not specific enough about the nature of the failed copies.  One thing to do is to always try testing your project from your first menu to see that it behaves correctly.  If you don't want your DVD to start playing automatically make sure you set it to open the Top Menu.  Then try a test either to your hard drive (if you can), or to a RW DVD.
    Message was edited by: tnsprin

  • URGENT HELP, How do you burn a DVD from Final Cut Pro

    This is my first video and I have to have it done by Wednesday, but I dont know how to take the movie from final cut and import to DVD Studio Pro. If anyone can help please let me know as soon as you can. Thanks Zack

    Hi Zack
    There are several ways to do it. To keep it simple just export a self contained movie out of FCP then import this into DVDSP. It will do all the encoding in the background for you. The prefered way is to export out of your timeline to Compressor and use one of the DVD-mpeg-2 presets. The preset you use depends on the the length of your project, the quality of the video, etc. Once you get to understand mpegging a bit more you can create your own settings to suit yourself. If you have to be done by tomorrow just keep it simple and get it done - then you can play another day : )
    Good luck
    B

  • MPEG-2 quality played on a monitor

    Hi,
    I have burnt a DVD using Encore 1.0. When the files are exported from Encore into a folder on the harddrive all the files including the VOB and IFO files all look fine and as they should do.
    However when I burn exactly the same project onto an actual DVD the VOP file looks as it should but the IFO files look washed out, with the blacks being too light. This is the case when played on a computer monitor.
    Unfortunately I'm not able to test it on a TV screen but I have heard that the quality for DVD MPEG-2s does not look correct when played on a computer.
    Does anyone know if this is true and if it is the norm. If this is the case does anyone know of any way around this so that it can play properly on a monitor?
    Any ideas would be appreciated.
    Thanks

    The monitor isn't calibrated. What I meant by the VOB and IFO files is that when I play the video from the VOB file it looks as it should however if I play the video from the IFO file it looks washed out.
    If it is a problem with the IRE levels shouldn't it look incorrect on all the files and look incorrect when the original MPEG-2 is rendered and not just from the IFO playback.
    Also, before I outputted the MPEG-2 from after effects I set the levels to 16-235. Does that mean that the IFO files make it play from 16-235? Is there not a way to make it look correct for playback on both TV screen and monitor?
    Thanks

  • IDvd - Onestep dvd from movie, not working?

    I am trying to make a onestep dvd from movie - from an avi file... but every time I make one (I followed all the directions perfectly). It looks like it is burning and takes about 4  hrs. but nothing happens. it just says I have inserted a blank dvd. Why does this keep happening?

    Hi
    from an avi file
    .avi is not the food for iDVD - it usually can not handle it at all.
    .avi - is no codec but a container - so one must use another program to figure out what codec that's in there.
    Then convert it to sometrhing iDVD can use.
    My UN-Structured/sorted notes up till Yet ! (May be MANY Faulth ! be careful)
    AVCHD
    • need of Intel Mac and iMovie’08 or 09 or 11
    • can be converted to AIC via Voltaic
    Containers.
    .mov.
    .avi. 
    You can use MPEG-Streamclip to convert some of the AVI files so that QuickTime can play them
    and then to streamingDV for iMovie.
    True file formats (?).
    .asf (from QuickTimeKirk)
    Your product is based on Windows OS and the .asf files are designed for Windows Media Player.
    Microsoft discontinued Mac support for Windows Media Player in 2003.
    iv50 - old codec on window platform.
    • Open on a PC-Window with Microsoft Movie Maker.
    • Put into TimeLine
    • Save on ”this Computer” as .wmv
    move over to Mac and open with QuickTime Pro and save as StreamingDV
    (if Flip4Mac is payed then no Waterstamp and time limit)
    or
    Open in FinalCut Pro as is = No  Waterstamp or time limit.
    Flip4Mac  -- //flip4mac.com
    is third party software that "plays" most WMP formats via QuickTime Player. They also sell upgrades that allow conversion from WMP to QuickTime formats.
    These upgrades are supported in iMovie version 6 but not for version 7 or 8 (iLife '08 and '09).
    So. What to do?
    Purchase one of the Flip4Mac upgrades.
    Copy the files from the SD card to your Mac and convert to QuickTime formats (DV Stream would work best).
    Import the new .dv file into iMovie (any version).
    .dv
    streaming DV    imports directly it is the same as from miniDV (tape) Camera
    .wmv
    iMovie is by concept meant to work with miniDV camcorders . . any other 'imports' need a conversion or are not supported... a quick solution would be purchasing a plug-in from www.flip4mac.com, 49$, which allows the conversion of .wmv (a PC format) into something useful for iM (dv-stream) ...
    or, ask the emailer to send it in some other codec .. mpg4 for example .. which will be converted by iM 'out-of-the-box' ...  and, to work with iM, the video should fulfill a few standards .. 720x480 pixel resolution, 30 frames per second ... otherwise, you will experience a dramatic loss of quality ..
    .mp4
    container not to be mistaken for .mpeg4 which is a codec - and it’s most often could contain a H.264 encoded material (PS3 and AppleTV)
    .m4v
    found in iMovie project folders - imported into iDVD without any problems
    .mov
    found in iMovie project folders - imported into iDVD without any problems
    .ram     real-movie by Real-player download
    Both Real Networks (.RM, .RA, and .RAM video files) and  Microsoft (.ASF, .WMA, and .WMV video files) makes it VERY difficult to  import footage encoded with these formats. Especially on a Mac.
    .mpg
    .mpeg
    .vob
    .vro
    .m2v
    .m2a
    .m2s
    .mts
    .m2ts
    .swf  files are Flash files. You need Perian
    .flv  Awkward timing in your choice of software as QuickTime 7.4 has dropped support (we hope it is temporary) for Flash Video formats (.swf or .flv file extensions).
    MPEG-1.          VideoCD
    MPEG-2.             DVD
    MPEG-4.         cell-phones to satellite TV - scalable
    //danslagle.dvmix.com/mac/iMovie/qt_plugins/3002.shtml
    Mpeg Streamclip. Supported formats.
    • MPEG, VOB, PS, M2P, MOD, VRO, DAT, MOV, DV, AVI, MP4, TS, M2T, MMV, REC, VID, AUD, AVR, VDR, PVR, TP0, M2V, M1V, MPV, AIFF, M1A, MP2, MPA, AC3...
    MPEG Streamclip converts from mpeg-1 to whatever you like (within reason).
    MPEG-2 Playback File Types.
    .mpg, .mpeg, .vob(2), .vro, .m2v, .m2a, .m2s
    QuickTime MPEG-2 Playback Component
    Recording types.
    DV                        standard miniDV (tape)
    DV Widescreen    16 X 9 on standard miniDV (tape)
    HDV 1080i            Full HD quality
    HDV 720p
    MPEG-4
    iSight
    From Mac to PC - convert to .avi or .wmv
    • Transport problem and 2?Gb limit on DOS/UNIX formatted hard disks - You need a
    hard disk formatted on a PC in NTFS format
    FAT 16 has a 2 or 4Gb file size limit
    FAT 32 should be able to handle larger ones
    • Rather copy back to miniDV tape (Camera) and use this
    QuickTimeKirk. You don't format the drive using a Mac.
    Use the PC to format using NTFS and avoid FAT 16 or FAT 32.
    //en.wikipedia.org/wiki/Windows_Movie_Maker
    Yep. They want DV-AVI as the format. Same thing but in an AVI container.
    Export from iMovie to AVI (Expert Settings) and click the "Options" button to set DV as the codec.
    Yours Bengt W

  • Mpeg 2 in premiere pro cc

    Hi, I Have a problem with premiere pro cc, in the list of exporting i don't have mpeg 2 , mpeg 2 dvd , mpeg 2 blue ray and when i'm importing mpeg in premiere pro, this don't see the sequence. what's happen? thanks

    Can you define 'glitch'?  Or better yet, show us?
    Do these glitches exist in the PP sequence, or only after export?
    How exactly are you viewing the exported videos?

  • Aaaaggghhh!!!! Stop cropping my DVD!!! Urgent help please!*

    Hi, would really really appreciate some help with this one.
    So, i shot my footage on an HD camera and have worked and edited the film in Final Cut Pro X (in 1280 x 720). It looks great, really happy with it!
    Now i need to put this onto DVD (just a normal DVD - not Blue Ray). I have Compressor 4.
    When i burn the DVD (MPEG-2) and play it on my mac, the video plays with the correct aspect ratio etc. When I then play the exact same DVD on other DVD players, it crops the image quite a bit. First of all, why is this? The Tv's I am playing it on are also HD but the DVD players are not. Secondly, what settings do I eed to use to create a DVD that will show the correct video aspects on normal DVD players.
    I have burned numerous DVDs with various settings, looking all over the net for advice as well. Using diffrent padding, aspect ratios etc and nothing seems to work. When i reduce the image size, the video quality also seems to get really poor.
    This video  will potentially be seen by thousands of people in my work organisation and they need the disk by Friday. This has to look good!
    Please help!
    Many thanks
    Matt

    If things work the way they are supposed to work in the chain from encoding to player to TV, the DVD should display full screen, 16X9 on an HD TV and letterboxed on an SD 4X3 set.
    For whatever reason, the chain seems to be broken with the equipment you are using. Only thing I can suggest is test the electronics gear and see what display adjustments can be made in cases where the image is not being displayed correctly.
    Or I suppose you could make two versions – a version for widescreen and a version for SD, That could be done in FCP by dropping the 16X9 version into a 4:3 project. You would wind up with letterboxed 4:3.
    Russ

Maybe you are looking for