I am having USB problems with my 2009 MacBook running OSX 10.6.8. They will open an 8GB flash drive, but neither of my 500GB WD HDDs.

After successful use of two WD 500 GB external drives something has happened and the drives show up, but I cannot access any files. One drive holds all of my pictures in iPhoto, but as soon as I attempt to run iPhoto the program stops responding and will no longer open through the HDD. My other external holds all of my business documents, and while the folders show up in Finder, none of the files show up when I open the folders. This problem began when I plugged my iPhoto drive in at the same times as an iTouch to dump some pictures. Halfway through the dump the HDD disappeared and has not worked since. Both of my drives work on a friend's Mac, so he recommended that I buy a USB hub to plug everything into as he suggested that my USB ports are not supplying the needed power to run the HDDs. I bought a D-Link DUB-H7, but the same problem persists. I have reset the PRAM, but nothing changed. Any advice will be extremely appreciated.

By the way, my iPhoto is version 8.1.

Similar Messages

I am having a problem with my 2009 Macbook Pro

Hello Everyone,
I am having a problem with my 2009 Macbook Pro . A few weeks ago I plugged it into the charger after running it down to reserve battery power. It appeared to be charging, but then all of a sudden my clock and calender reset to year 2000 and then my computer blacked out and went dead. I tried to boot it up but nothing happened (literally nothing). I have tried 3 different chargers on it, but all I get is a faint green light and even after hours it still won't boot up. I have tried replacing the battery, but still nothing happens.
Any Ideas? I am pretty desperate to get my computer back up and running before school finals.

You may have to see if an authorized Apple service specialist can check over
the charging system (magsafe dc-in board, power adapter, and MacBook/Pro)
and test or run a diagnostic on it, to be sure there is no damage or failed parts.
When you attached the adapter to charge the computer, after it said it was going
to reserve power, did you shut down open applications and stop using the MB/Pro?
That would've been the thing to do, since the margin of run-time near the bottom
of the power cycle can be wrong by the gauge estimate, it can just quit.
While I have not researched your year/model/series in detail, I do know some
models of Apple portable computers have a small battery or capacitor on the
logic board, separate from the main power battery; it may need replacement.
A service provider w/ Apple training & parts would be a likely resource to fix it.
Good luck & happy computing!

I can't move photos from iPhoto to my secondary hard drive or to a burn folder. I have never had a problem with this before. This is something new.   They will not drop into either folder. Nothing happens.

I can't move photos from iPhoto to my secondary hard drive or to a burn folder. I have never had a problem with this before. This is something new.   They will not drop into either folder. Nothing happens.
I checked my secondary harddrive and there is plenty of memory.
I emptied my burn folder but the photos still will not drop into it.
I created a new burn folder, no luck with this either.
230 photos is the maximum size of the events I am trying to move from iPhoto to save elsewhere.
I have shut down and restarted my computer.   No change. The photos still will not drop out of iPhoto.
My Mac Computer Storage shows that I have 62.2GB free out of 249.2GB (movies, photos and contacts taking up the most space)
My Lacie External Harddrive (2TB capacity) shows that I have 1.79TB available. It shows that 207,729,520,640 bytes (207.73 GB on disk) are used.
I have never had this problem before. It is usually very easy to move my photos from iPhoto.
I am not a computer expert (I work in surgery so don't have a need for lots of computer knowledge) so please explain in simple terms.
Thank you so much for any help you can provide.
I really appreciate it.

YES Terence! Thank you. Exporting allowed me to move my photos from iPhoto into the Burn Folder on my desktop.   But that doesn't explain why I'm having to go that route now.   Have I done something (accidentally changed some setting) on my computer that will not allow me to just click and drag anymore?   I really liked the convenience of the click and drag option.
I don't have the time tonight to export and burn a lot of CD/DVDs. I'll try that tomorrow and make sure my photos are moving properly. I also need to export photos to my external hard drive to make sure that route is working.
Wouldn't you know that my Apple Care Plan runs out this Wednesday?! I need to make sure everything is working properly before that expires.
Thank you so much for your help.   I really, really appreciate it.

Have problems with Mail on MacBook running OS X Mavericks. It suddenly became stuck: won't quit and won't display any messages. Please help.

Have problems with Mail on MacBook running OS X Mavericks. It suddenly became stuck: won't quit and won't display any messages. Please help.

Select Force Quit from under the Apple menu and select Mail (it may say that it isn't responding).
Clinton

I am having a problem with email, when I delete messages from my Ipad, they come back into trash whether they are on my PC or not. The only way I can delete them is to to my providers site and delete everything there.

I am having a problem with email. I can receive and send, but when I delete, the deleted messages return into either Trash or Bin or both whether or not I have deleted them from my PC.
The only way I can get rid of them permanently, is to go into my area of my providers site(Sky) and empty all of the boxes there. I imagine it's a setting, please advise.

For IMAP mail only.
Settings>Mail, Contacts, Calendars>tap on mail account>Archieve Messages>OFF

Samsung hard drive problems with mid 2009 Macbook Pro

Arghh, this is driving me mad.
I'd like to know if anyone has installed a Samsung HM641JI SATA II hard drive into a mid 2009 Macbook Pro (mine is a 2.8Ghz) and, if so, how they managed it. The drive is 640GB. These are the steps I've taken:
1. Swap out the stock drive for the Samsung
2. Boot from a USB drive which contains a mirror of my system
3. When the system identified the new disk, I formatted it with 2 partitions (GUID table, HFS journaled)
4. Reboot
5. System is very slow. Boots from USB but can't use keyboard to login
6. Switch off and try again
7. Remove Samsung drive
8. Reboot from USB (works perfectly)
9. Downgrade firmware to 1.6
10. Replace samsung drive and try again
11. System boots from USB
12. Verify that drive is running at 1.5Ghz
13. Disk utility and system profiler both crash
14. Disk unmounts by itself and other random weirdness
15. Remove Samsung drive
I've read endless reports about the firmware in this model of Macbook Pro and its issues with SATA II but struggling to find anything current and specific. Two questions:
a. Is there anythign I can do to get this drive to play nicely?
b. What drive should I get if the answer to a is no?
As a bit of background.. my system began playing up last week with lots of spinning beach balls resulting in forced switch offs. Booting from a mirror on a USB drive works perfectly so I concluded that the drive was on its way out. A drive test utility confirmed this. I'm now wondering if it really was the drive or the cable or the logic board.
Any advice appreciated.
Cheers
//A

I'm coming around to the idea that this might be a problem with the SATA cable rather than the drive.
I currently have the stock drive (Hitachi) back in the macbook. It mounted for a while and was then ejected when I tried writing data to it. System profiler reports that "There was an error while scanning for Serial-ATA devices."
I was able to mount the same drive in a USB enclosure this afternoon without any problems. Right now, I seem to be having issues with both the Samsung drive and the Hitachi drive - I wasn't suspicious of thr latter because I thought it was failing.
I found one or two accounts of other people having similar problems that were resolved with a new sata cable.
How does a cable fail? Could this be my problem?
Cheers
//A

Having a problem with noises and mouse jumping, tried to reinstall and computer will not allow me to select the correct install icon. Sends me to xcode install

my kids computer began acting up this spring...so I shut it down.
Would not stay turned off, various noises almost continually, jumping highlights, etc.
Decided to reinstall os x snow leopard. insert disc and icon appears. then 3 icons with x in a column.
automatically highlights middle icon and will not allow me to select one above. Says install xcode.
not what i want to do.
any help?

What model iMac do you have?
What version of Mac OS is it running? If you don't know, try to give approximations on when it was set up and whether it was ever updated so we can take our best guess.
How are you trying to boot from the install disc? Your description of 3 icons with x in a column' leads me to believe that you aren't booting from the install disc, but rather you are inserting the disc after booting from the OS that is installed on the hard drive. If that is what is happening you'll see something like this, although it will vary depending on the actual version of the Install Disc that you have and how you've chosen to view the files (icon, list, column, etc).
What happens if you restart the system with the Install Disc inserted, then quickly hold down the 'c' key so that the system attempts to boot from the Install Disc. Do you still experience the same issue?

Problem with mid-2009 MacBook Pro 13" hard drives

In May of this year I upgraded my stock hard drive to a 500GB Hitachi from the stock 160. About 5 days ago the computer froze and hung gor several minutes. Mouse still moved but no response from the OS. Forced a restart after several minutes. The computer rebooted, but showed no hard drive. Install DVD (Snow Leopard) doesn't detect hard drive, neither does disk utility. I put the old hard drive back in, everything is fine. The OS finds updates available, updates to 10.6.4. Tonight, the same precise thing happens on the old drive. No disk showing in the installer or disk utility.
Any suggestions?

Run the Apple Hardware Test you'll find on one of the DVDs that came with your computer. Swap the drives again and repeat the test, so you'll have results from each drive. Note the exact text of the error message each time, then make a Genius Bar appointment at your nearest Apple Store, or take the machine to an authorized service provider for diagnosis, being sure to take along copies of the error messages.

My Canoscan 9000f doesn't work with either my MacBook running OSX 10.4 Tiger, or my PC on Windows 7.

The "on" button lights up, but nothing happens when the other buttons are pressed. No preview scan happens on PC, and No sign of life whatsoever on Mac. Any suggestions? Thanks!

Thanks for that. I did indeed manage to do a calendar backup from my 6230i and then restore it to my 6300 and YES it did work.
So how come that a calendar that obviously works on the 6230i phone can be restored to the 6300 phone, and the 6230i can do a sync to outlook. Yes I did that as well. I managed to sync the 6230i to a clean calendar in outlook, Modify it the calendar in Outlook and then sync it back to the 6230i. I then had to back it up in order to restore it to the 6300.
Are you seriously saying that it is the format of the calendar when the 6230i does it so well. It seems obvious to me that it must be either the sync firmware of the 6300 or the PC connect software not taking account of any 6300 firmware differences.
As a test I added an appointment to a completely blank calendar on my 6300 and tried syncing that with the same errors. When syncing you can for a split second see something trying to be synced but too fast to read. It would be more helpful if there was a proper log of actually why and where the problem occurred. So if Nokia (or anyone)has some debug software please can I try it?
Whilst I have, after nearly a week of trying and search the internet, found a solution to my immediate problem (copying the calendar), it appears there isn't a solution to integrate the phone to Outlook - unless somebody know different.

Is anyone else having a problem with a "no service" issue on the iPhone 5?

There are times my phone will go to "No Service" when the signal is low. I just got the iPhone 5. I did not have this problem with my 4. It doesn't say "searching..." it just automatically says "No Service" for a few seconds and then back to having bars. It comes and goes. I had my phone replaced at the Genius Bar and still have this problem. Is anyone else also having this problem? I hope it's just a software issue they will solve with an iOS update.

I have this problem all the time. when i get back home from a overseas trip (about 3-4 times a month) I have to turn airplane mode of and on a few times to get rid of the "No Service" message.

New problem with display on Macbook Pro retina (Samsung panel)

Hello All,
I am a very new people on your forum but a few weeks ago i bought a new macbook pro retina with samsung panel.
I haven't ghosting effect on my macbook but i have a new and really bad problem.
I try to found a some information on Russians forums but nobody can help me with it.
I can see an artifacts in the form of flashing pixels on all display.
It occurs in 20-30 minutes after the start of work.
Today i try to test it on game Dirt 2 and i can see defects after 2 minutes after start. So i think it can be reason with Geforce 650 but when i back to desktop and use HD 4000 i still see a problem.
This is best seen on a black screen with high backlight.
When i try to connect TV via HDMI i can't see any problem in my TV.
So i really don't know what could be the reason.
I attached the video with issue to video hosting
http://vimple.ru/579f880e8b7045e09f8fc5bc097c5e2b
Also i have a many software problem like Crashing safari and iTunes. It can be a few times per day.
I really disappointed with my new Macbook.
I haven't any problem with old 2009 Macbook pro with Snow Leopard but Mountain Lion is not working well.

Option 1
Back Up and try rebuild the library: hold down the command and option (or alt) keys while launching iPhoto. Use the resulting dialogue to rebuild. Choose to Rebuild iPhoto Library Database from automatic backup.
If that fails:
Option 2
Download iPhoto Library Manager and use its rebuild function. This will create a new library based on data in the albumdata.xml file. Not everything will be brought over - no slideshows, books or calendars, for instance - but it should get all your albums and keywords back.
Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one. .
Regards
TD

I am having a problem with very slow start up after expanding RAM on my 2009 Mac Pro.

I am having a problem with very slow start up after expanding RAM on my 2009 Mac Pro (8 Core 2.93GHz). When I run the Mac Pro with 2 x 2Gb RAM it takes 4 seconds before the gray screen, chime and spinning wheel appear.However when I expand the RAM to 20GB the grey screen and chimes appear after a long 20+ second black screen.
The RAM modules are paored 2 x 4GB Crucial CT51272BA1339.M18FMR and 6 x 2GB SAMSUNG M391B5673FH0-CH9, all DDR3 ECC.
Reading articles on the internet, I thought it may be damaged RAM modules, but I have completed memtest and all are okay. I have tried changing the pairs around and if I use any paired 2 modules the Mac Pro starts normally, only when I try running more than 2 modules the delayed start up happens. (black screen 20 Seconds)
I also have tried PRAM and SMU resets after changing the RAM setups, and the issues always occurs when I have more than 2 modules. As you can see I have 6 SAMSUNG modules and even with identical modules the issue happens, when increasing the RAM to more than 2 modules.
The Mac Pro runs fine after the start up screen and can see all the modules, but has anyone else come across this issue, or have any ideas as to why my Mac Pro is taking 20 seconds to start up with 20 GB RAM?

Hi there. Thanks for your comments.
I have tried all the different combinations of RAM setup, and as stated in my initial topic, the Mac Pro boot up time only slows when I have more that 2 modules. Where I place these does not seem to make a difference.
I have taken the Mac Pro to an Apple Reseller technician yesterday and they where not able to find any RAM errors. Apparently the boot up time is within Apple's acceptable parameters for this set up.
Could anyone that is running a Mac Pro 2009 with more that 4 modules of RAM, please let me know if the boot up time is normal. ( the time it takes from pressing the power button to seeing the gray screen around 16 - 20 seconds)
Or is anyone else having the same issues?
thanks for your responce

My ipod touch will not switch on and is no longer recognised by itunes. Before this i tried to restore it as I was having some problems with it switching off and on by itself randomly.

My ipod touch will not switch on and is no longer recognized by itunes. Before this i tried to restore it as I was having some problems with it switching off and on by itself randomly.
I tried to restore it and I got error code 2009, so I closed it tried again got error code 1659, now it wont do anything and it's not recognized by my pc /itunes please help x

For the restore error messages try:
iTunes: Specific update-and-restore error messages and advanced troubleshooting

Having connection problems with Mail after installing 10.9.4

I upgraded to 10.9.4 a few days ago, and ever since, I've been having connection problems with Mail. First, it stops downloading new mail automatically and second, it won't send any of my messages. When I try to send, I get a message that it is unable to connect.
Quitting Mail and restarting it seems to clear the problem, but then it happens again, maybe an hour or two later.

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
Don't be put off merely by the seeming complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. All it does is to collect information about the state of the computer. That information goes nowhere unless you choose to share it. However, you should be cautious about running any kind of program (not just a shell script) at the behest of a stranger. If you have doubts, search this site for other discussions in which this procedure has been followed without any report of ill effects. If you can't satisfy yourself that the instructions are safe, don't follow them. Ask for other options.
Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
4. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
5. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
6. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts SerialATA 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports ' com.clark.\* \*dropbox \*GoogleDr\* \*k.AutoCAD\* \*k.Maya\* vidinst\* ' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 ` route -n get default|awk '/e:/{print $2}' ` 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB com.apple.AirPortBaseStationAgent 464843899 51 );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^$[0-9]+$ /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n-\t%s\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' /^ *$|CSConfigDot/d;s/^ */ /;s/[-0-9A-Fa-f]{22,}/UUID/g;s/(ochat)\.[^.]+(\..+)/\1\2/;/Shared/!s/\/Users\/[^/]+/~/g ' ' s/^ +//;5p;6p;8p;12p;' ' {sub(/^ +/,"")};NR==6;NR==13&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: [^EO]|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<200) print "com.apple.";} ' ' $3~/[0-9]:[0-9]{2}$/ { gsub(/:[0-9:a-f]{14}/,"");} { print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { print "'${p[41]}'";if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$|'${p[41]}'/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/root/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1100) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/ { next;} /(etc|Preferences|Launch[AD].+)\// { sub(".(/private)?","");n++;print;} END { print "'${p[41]}'.plist\t'${p[42]}'";if(n<500) print "Launch";} ' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| |\n","\\|\\|kMDItem'${p[35]}'=");sub("^...."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[43]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/ { next;} /%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]" "$1;b=b$1;} END { if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text$|POSIX sh.+ text ex)/) F=F" ("T")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' /^ +[NP].+ =/h;/^( +D.+[{]|[}])/{ g;s/.+= //p;};' 's/0/Off/p' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / / { print "'"${p[28]}"'";exit;};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/$L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9;} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ /V/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' ' /^find: /d;p;' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps sudo\ crontab sudo\ iotop top pkgutil 'PlistBuddy 2>&1 -c "Print' whoami cksum kextstat launchctl sudo\ launchctl crontab 'sudo defaults read' stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' defaults\ read scutil sudo\ dtrace sudo\ profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil sudo\ lsof test );c2=(com.apple.loginwindow\ LoginHook '" /L*/P*/loginw*' '" L*/P*/*loginit*' 'L*/Ca*/com.ap*.Saf*/E*/* -d 1 -name In*t -exec '"${c1[14]}"' :CFBundleDisplayName" {} \;|sort|uniq' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' :${p[35]}\" :Label\" '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message Req 'bad |Beac|caug|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|n Cause: -|NVDA$|pagin|proc: t|Roamed|rror|ssert|Thrott|tim(ed? ?|ing )o|WARN' -k Message Rne 'Goog|ksadm|SMC:' -o -k Sender fseventsd -k Message Req 'SL' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cgh] ! -name *ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true $ -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '-L {/{S*/,},}L*/Lau* -type f' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,E}* {/,}L*/{A*d,Ca*/*/Ex,Compon,Ex,In,iTu,Keyb,Mail/B,P*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,pam.d/*,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t /S*/L*/Lau*/*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' -i4TCP:0-1023 com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' );N1=${#c2[@]};for j in {0..9};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents launchd Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching SATA );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};';done;A7(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0(){ [[ "$v" ]]&&echo "$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "$s"<<<"$v"`&&C1 1 $1;};for i in 1 2;do for j in 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;A2 0 $((N1+1)) 2;C0;A1 0 $N1 1;C0;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;D13 0 $((N1+9)) 59 50;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 14 12 14;D22 6 36 13 15;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D22 11 17 17 20;for i in 0 1;do D22 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A2 19 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;A2 4 20 21;B7 6;B2 9;A4 14 7 52 9;B2 10;B6 9 10 4;C3 25;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;D13 24 24 32 31;D13 25 37 32 33;A2 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D13 21 0 32 19;D13 10 42 32 40;D22 29 35 46 39;};D13 14 1 48 42;D12 34 43 53 44;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 26 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D23 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 20 42 32 41;D13 14 2 48 43;D13 4 5 32 1;D13 4 3 60 5;D12 26 48 49 49;B3 4 22 57;A1 26 46 56;B7 22;B3 0 0 58;C3 47;D22 4 4 50 0;D23 22 9 37 7;A7;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
7. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
8. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
9. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
10. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report the results. No harm will be done.
11. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start Time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
12. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
Note: This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

I am having same problem with apple tv need 4.4 version and can not find solution this a brand new product out of box yesterday why would it not already have updated version. I am getting frustrated that I can not get this mirroring icon to work. I

I am having same problem with apple tv need 4.4 version and can not find solution this a brand new product out of box yesterday why would it not already have updated version. I am getting frustrated that I can not get this mirroring icon to work. I have tried all suggestions in this thread and nothing works. I also hooked up to laptop through iTunes with micro USB nothing!!!

The new appletv software came out 2 or 3 days ago, how would Apple get it on the device in the box in a store?
Why don't ou update the appletv software?

I am having USB problems with my 2009 MacBook running OSX 10.6.8. They will open an 8GB flash drive, but neither of my 500GB WD HDDs.

Similar Messages

Maybe you are looking for