I can connect to 3G, but cannot send messages or call with my iphone 4.
I can connect to 3G, but cannot send messages or call with my iphone 4.
SMS and calls are carrier features. Check with your carrier
Similar Messages
-
I cannot send mail from Firefox. Can receive E-mail but cannot send it. This worked OK until today. I have had firefox for many years. Just reinstalled Mozilla and still cannot send E-mail from firefox.
I use comcast.net for E-mail,using Mozilla to get there.If your Office email account's SMTP authenticated?
Any error message provided and if so, what?
Are you also accessing an email account and SMTP server provided by SBCGlobal.net with either email client and if so, are you able to send messages with this account and SMTP server when connected to the internet via SBCGlobal.net at home?
And let me get this straight - both email clients work fine without any problems sending messages with your Office email account and SMTP server when connected to the internet at a friend's house that uses another ISP besides SBCGlobal.net but this is an Apple problem?
If an Apple problem, then you'd have problems sending messages with this account and SMTP server regardless whose network and ISP you are connected to.
Regardless what this more than likely under-trained or just unaware person at SBCGlobal.net told you, all ISPs have restrictions on using an SMTP server that is outside of their network or that isn't provided by the ISP used for connecting to the internet.
Some ISPs allow the use of an authenticated server only that is outside of their network but some block its use regardless.
Within the last year or so, SBCGlobal.net made a drastic change in regards to such restrictions and conveniently neglected to inform their customers beforehand. Those using an SMTP server that was outside of SBCGlobal.net's network regardless if the SMTP server was authenticated were required to "opt out" of Port 25 blocking with SBCGlobal.net in order to use an SMTP server that was outside of their network which was working fine before this change was made.
Have you opted out of Port 25 blocking with SBCGlobal.net? -
TS2755 since updating to ios7 I can receive e-mails, but cannot send e-mails from my phone
since updating to ios7 I can receive e-mails but cannot send e-mails from my phone
Hi there ritawilk,
You may find the troubleshooting steps in the article below helpful.
iOS: Troubleshooting Mail
http://support.apple.com/kb/ts3899
-Griff W. -
Installed Facetime on MacOSX10.6.8 but cannot send or receive calls?
Installed Facetime on MacOSX10.6.8 but cannot send or receive calls?
Hello, Tinapepina.
Thank you for the question. This article will help you troubleshoot the issue you are experiencing with FaceTime on your iMac.
FaceTime for Mac: Troubleshooting FaceTime
http://support.apple.com/kb/ts4185
Cheers,
Jason H. -
Can get incoming mail but cannot send mail
Can get incoming mail but not send mail
iOS: Unable to send or receive email
http://support.apple.com/kb/TS3899
Can’t Send Emails on iPad – Troubleshooting Steps
http://ipadhelp.com/ipad-help/ipad-cant-send-emails-troubleshooting-steps/
Setting up and troubleshooting Mail
http://www.apple.com/support/ipad/assistant/mail/
Server does not allow relaying email error, fix
http://appletoolbox.com/2012/01/server-does-not-allow-relaying-email-error-fix/
Why Does My iPad Say "Cannot Connect to Server"?
http://www.ehow.co.uk/info_8693415_ipad-say-cannot-connect-server.html
iOS: 'Mailbox Locked', account is in use on another device, or prompt to re-enter POP3 password
http://support.apple.com/kb/ts2621
iPad Mail
http://www.apple.com/support/ipad/mail/
Configuration problems with IMAP e-mail on iOS with a non-standard SSL port.
http://colinrobbins.me/2013/02/09/configuration-problems-with-imap-e-mail-on-ios -with-a-non-standard-ssl-port/
Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
Or this - Delete the account in Mail and then set it up again. Settings->Mail, Contacts, Calendars -> Accounts Tap on the Account, then on the red button that says Remove Account.
Cheers, Tom -
QUESTION : when I log into hotmail on my new ipad, I only see inbox where I retrieve my messages but cannot see the word ''New'' which would
allow me to send emails the way it would be on a desk pc. So I can retrieve my messages but cannot send ???
Thank you in advance for help.The icon in the upper right of the screen (assuming you are using the Mail app) that looks like a square with a pen is the new message button. Tap that to create a new mail message.
-
have Imac with 10.6.8. osx....can receive emails but cannot send & have .mac email . was working fine last week
Please carefully read and follow the trouble shooting steps in Apple's article:
http://support.apple.com/kb/TS1307 -
Can receive text msgs but cannot send!?!?
A few days ago I began to be unable to send text msgs. Using iPhone 3G, it appears that the 'send' button is dithered 'greyed' out. I tap it but nothing happens. I can email, and obviously type text online (as here) but cannot 'send' text. I deleted MSG history, cleared cache, cleared recent calls, cleared email history to no avail. I can receive text just dandy but cannot send. Can anyone shed some light here or do I go see the 'geniuses' at the store and get a new phone. ( it seems every time I have a phone problem like this, they can't fix it they just give me another phone) Would really like to not have to go to the store. Thanks in advance for anyones help!
I would try a few basic things before scheduling an appointment with the Genius Bar.
1) Sync your iPhone with your computer. I have noticed that sometimes my phone will have a hiccup and when I sync it, whatever was wrong automatically rights itself.
2) Reset your iPhone holding down the "home" button and the Sleep/Power button on the top right side of the phone at the same time. It takes about 5-15 seconds and you want to make sure you hold down both buttons until you see the apple logo, ignore the slider.
3) Plug your iPhone into the computer and perform a phone restore. There are 2 options for this:
a- If you know when this problem started with your SMS messaging you can restore from a backup that was done on a previous sync. Chose a date prior to this issue starting and restore your phone to how it was on that date.
b- If you don't know when this issue began or restoring it to an earlier date does not fix the problem you can restore it to how it was when it came out of the box.
I hope that one of these things is able to solve your problem with SMS messaging. If none of these fixes the problem you should schedule an appointment with the Genius Bar and get this resolved with them. If you visit the Genius Bar make sure to sync your iPhone just prior to your appointment so if they need to replace the iPhone you don't lose any calendar entries, recently added contacts, pictures, etc.
Good luck!
~CaliGirl~ -
I added a contact but cannot send message to that person
Good morning, My daughter added my son (he has a new i-pod) to her contacts but cannot send him an instant message. She is able to send messages to her friends etc.
Also I have noticed she cannot get any of her hotmail emails to her ipod either.When you send a Message you have to have the Subject line filled in, If not the Send button is inactive.
You said " my son can message my daughter but she can't message him back."
Do you mean she can't reply successfully to the his Message?
http://support.apple.com/kb/ht1694
iOS: Setting up an Outlook.com, Hotmail, Live, or MSN email account -
i put a new vodaphone sim into an iphone and all is great except i cannot send or receive photos with my texts
Have you tried contacting Vodafone to make sure MMS messaging is enabled on your account?
-
837 - can receive e-mail but cannot send.
Hi guys,
I've just installed a 837 at restaurant. The client checks his e-mail via outlook. He can receive e-mail but gets errors when trying to send. Any ideas. Everything else works great.
Thanks in advance.Hi Guys,
The guru in our office that configured this router
says that he cannot figure out why we cannot send e-mail via outlook. I put the old router and cable modem back in at the site and we could send and receive e-mail via outlook fine. ( PPOE setup )
Put the Cisco back in and no luck.
This is the config file. If anybody can point me in the right direction to make the change I will try it at the site. We are using port 4 (10.100.100.1)to connect to a linksys for public internet access. He is behind the 192.168.100.xxx subnet.
Hope this helps.
Thanks in advance.
ip virtual-reassembly
ip tcp adjust-mss 1452
hold-queue 100 out
interface Ethernet2
ip address 10.100.100.1 255.255.255.0
ip access-group 106 in
ip nat inside
ip virtual-reassembly
no cdp enable
hold-queue 100 out
interface ATM0
no ip address
atm vc-per-vp 256
no atm ilmi-keepalive
dsl operating-mode auto
pvc 0/35
pppoe-client dial-pool-number 1
interface FastEthernet1
duplex auto
speed auto
interface FastEthernet2
duplex auto
speed auto
interface FastEthernet3
duplex auto
speed auto
interface FastEthernet4
duplex auto
speed auto
interface Dialer1
description ip address negotiated
ip address negotiated
ip access-group 111 in
ip mtu 1492
ip nat outside
ip inspect myfw out
ip virtual-reassembly
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname [email protected]
ppp chap password xxx
ppp pap sent-username [email protected] password xxxx
ppp ipcp dns request
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1
ip http server
no ip http secure-server
ip nat inside source list 102 interface Dialer1 overload
ip nat inside source static tcp 192.168.100.250 5631 interface Dialer1 5631
ip nat inside source static udp 192.168.100.250 5632 interface Dialer1 5632
access-list 102 permit ip 192.168.100.0 0.0.0.255 any
access-list 102 permit ip 10.100.100.0 0.0.0.255 any
access-list 105 deny ip 192.168.100.0 0.0.0.255 10.100.100.0 0.0.0.255
access-list 105 permit ip any any
access-list 106 deny ip 10.100.100.0 0.0.0.255 192.168.100.0 0.0.0.255
access-list 106 permit ip any any
access-list 111 permit udp any any eq 5632
access-list 111 permit tcp any any eq 5631
access-list 111 permit tcp any any eq telnet
access-list 111 permit icmp any any administratively-prohibited
access-list 111 permit icmp any any echo
access-list 111 permit icmp any any echo-reply
access-list 111 permit icmp any any packet-too-big
access-list 111 permit icmp any any time-exceeded
access-list 111 permit icmp any any traceroute
access-list 111 permit icmp any any unreachable
access-list 111 permit udp any eq bootps any eq bootpc
access-list 111 permit udp any eq bootps any eq bootps
access-list 111 permit udp any eq domain any
access-list 111 permit esp any any
access-list 111 permit udp any any eq isakmp
access-list 111 permit udp any any eq 10000
access-list 111 permit tcp any any eq 1723
access-list 111 permit tcp any any eq 139
access-list 111 permit udp any any eq netbios-ns
access-list 111 permit udp any any eq netbios-dgm
access-list 111 permit gre any any
access-list 111 deny ip any any
dialer-list 1 protocol ip permit
control-plane
line con 0
exec-timeout 120 0
modem enable
stopbits 1
line aux 0
modem InOut
modem autoconfigure type usr_sportster
stopbits 1
speed 19200
flowcontrol hardware
line vty 0 4
exec-timeout 120 0
login local
length 0
scheduler max-task-time 5000
end -
Connects to router but cannot send or receive data
I have a WRT54G. I can find the network and connect to the router, but I cannot send or receive any data. I tried plugging directly into the router and I am still unable to send or receive any data. Both computers on the router has the same problem. I did a reset of the router back to default settings and still no luck. Any thoughts? Thanks in advance for the help.
Solved!
Go to Solution.First thing which you can try is, when you Modem and Router is connected to each other, Unplug the Power from Router and Modem , wait for 30 seconds then plug the Power to the Modem and once all the lights are solid then plug the power to the Linksys Router, now check if you are able to go Online. If still not then ....
Who is your ISP. So i think you need to Re-configure all the settings on your router back again.
If your Internet Service Providor is Cable follow this link
If your Internet Service Providor is DSL follow this link -
Federated user can log into mailbox, but cannot send email
Hello. Of several dozen federated users with mailboxes in Exchange Online, I have one user who suddenly cannot send mail from his own mailbox, always receiving a, "you do not have the required permission to send from this mailbox." He used to be
able to send, and I've reviewed and compared his mailbox properties and mailbox permissions with other federated users, and I can find nothing to explain these errors. The "NT Authority\Self" identity is listed in the Send-As permission, just as
it is on every other user's mailbox. I even tried explicitly adding the user's account to the Send-As permissions, which made no difference, so I removed it again.
As I said, the user can successfully log into his mailbox and can read his mail, but all attempts to send anything out fail with the same error. Any ideas?
Thanks,
MikeTurns out the problem was caused by two things:
1) the user has a K2 (kiosk) license
2) in Settings, the user checked the box to "always show the From field"
Apparently, despite the fact that this user had access to no mailboxes other than his own, when you turn on the From field, Exchange apparently does some sort of check for Send on Behalf of rights whenever the user hits Send, even on his own mailbox, and
the Kiosk license excludes the ability to Send on Behalf Of any mailbox.
The bottom line is that, unchecking the "always show From field" checkbox resolved the issue and allowed the user to again send mail.
I'm a bit annoyed by this. If the Kiosk licenses limits a feature like this, then it should remove or deactivate the GUI element, to prevent it from causing this sort of error from occurring. -
Cannot send pictures through imessage with new iphone 5s?
Since I upgraded from the Iphone4s to the Iphone5s I have not been able to send pictures through imessage? Anyone experiencing the same problem or know how i can fix this? I looked under messages in settings and made sure everything was turned on.
ThanksI had this issue and resolved it with a hard reset. Holding sleep button and home button at same time until phone reboots.
-
Can receive IMAP mail but cannot send
I have set up my webmail as per the instructions given me, but I can only receive mail, I can't send from AppleMail. Any ideas about what I'm doing wrong?
Welcome to Apple Discussions, lilwonton77.
Unfortunately, you don't provide enough information. What's your webmail? Have you made sure to set up the correct server-port? Maybe you have to check that smtp uses SSL... Just to name a few. For example, if you're using GMail, make sure to use the settings described by Google [here|http://mail.google.com/support/bin/answer.py?answer=78799&topic=12814].
To set up an outgoing server go to Apple Mail's Preferences > Accounts, select your account, click on the tab "Account Information" and select "Customize Server List" from the drop-down menu in the section SMTP-Server.
Hope that gets you started.
floba
(MN435)
Maybe you are looking for
-
Oracle9i Application Server Release 2 version
Hi i have Oracle9i Application Server Release 2 on IBM-AIX I found this: http://www.oracle.com/technology/documentation/ias.html How i can check what is my exact version?
-
How to find a word in select text?
if offer is in select text, i want display some message. How can i find select text contains offer using JS?. selObj.options[selIndex].text == "%offer%"
-
When I had to do an update for GarageBand on my ipad2. I had not enough memory to instal the update. So I deleted the app and tried to install my app again but it says installing when it's not. So I can't purchase GarageBand ever again. PLEASE HELP!
-
Bette way to referenced tree model nodes from UI to perform actions on them
A singleton facade is built. Its init() method loads several "tree model configs", each of them referenced by a name. This singleton creates a Project instance for a given "tree model config" calling the facade method -> createProject(String pjrName,
-
User management in Sun Application server PE 9
I need to be able to manage (create, edit, delete) users in my AS for a specific app. Is there an API I can use to access the user information in the AS? Can I create new users, edit and delete them? If this is not possible: Does anyone know how to m