I cannot get phone signal when abroad

I have an iPhone 4S and cannot get a signal when out of my home country. Is there a solution for this by changing the phone settings?

Did you enable international use with your carrier before you left? If you did, check Settings>General>Network and make sure that Roaming is turned on.

Similar Messages

  • HT1414 cannot get phone signal

    Cannot get phone sinal?

    Make sure you put a valid sim card into the phone firstly and if you have, take it out and put it in again.
    Other than that you need to contact your carrier regarding phone signals - a signal is the province of the carrier and nobody else.
    Contact your carrier.

  • 5130 cannot get phone connection, using as modem

    Recently purchased 5130 to use as modem for my laptop.  Am using sim card from primary phone to access internet (primary phone has internet service), and connection with USB cable.  Downloaded PC suite, have Vista OS.  Have set specs to phone and internet provider (AT&T) but cannot get connection.  Error display says cannot get phone connection.  Phone works in phone mode, although cannot see contacts.
    ( I have a new bluetooth USB adaptor, but do not want to open package if I can get cable to work.  No point in opening blue tooth yet as cannot even get phone connection.)
    Any advice? 

    Hello, dthurnherr.
    Thank you for visiting Apple Support Communities.
    Here are a couple troubleshooting articles that I would recommend going through when experiencing this issue.
    FaceTime for Mac: Troubleshooting FaceTime
    http://support.apple.com/kb/ts4185
    Unable to make or receive FaceTime calls after April 16, 2014
    http://support.apple.com/kb/TS5419
    Cheers,
    Jason H.

  • Macbook will not get wifi signal when docked into hedge dock station

    My Macbook will not get a wifi signal, whenever docked into the Hedge Dock Station. It will however, get the signal when out of the station. It worked for months before.

    Wi-Fi is not Bluetooth. If you are using the phone as a Wi-Fi hotspot, then you connect to it using Wi-Fi, not Bluetooth. There's no Bluetooth pairing involved.
    Turn on the Wi-Fi hotspot feature on your phone.
    On the Mac, open System Preferences and click on the Network icon.
    Select "Airport" in the left pane and then click the "Turn AirPort On" button.
    Select the name of your phone in the drop-down next to "Network Name".
    Provide the password you setup for the network on your phone.
    It's nice to have the ability to turn the Wi-Fi on and off in the menu bar rather than have to open System Preferences each time. You can click the checkbox next to "Show AirPort status in menu bar" in the Network pane to do just that.

  • I made a movie with iMovie and cannot get the audio when I burn into dvd. I would like to transfer video to a dvd to be played in any computer and TV

    I made a movie with iMovie and cannot get the audio when I burn into dvd. I would like to transfer video to a dvd to be played in any computer and TV

    Go to the Map mode in your iDVD project and make sure the blue bin at the left is empty.  That's where you drag slideshows to if you want the DVD to open immediately to that slideshow and bypass the menu. 
    Click to view full size
    If there is an item in there drag it out.
    OT

  • Just got a used airport base station. Set it up and getting wif signal. when I try to hook up on a computer it asks for a security key. where can I locate key?

    just got a used airport base station. Set it up and getting wif signal. when I try to hook up on a computer it asks for a security key. where can I locate key?

    If you mean the hexidecimal equivalent of the alphanumeric password, then you can find this via the AirPort Utility, as follows:
    AirPort Utility > Select the AirPort > Manual Setup
    On the AirPort Utility's menubar select Base Station > Equivalent Network Password

  • Cannot get any sound when playing .avi files

    Hi All
    I am running QT version 6.5.3 on Mac OS X 10.2.8 and cannot get any sound when playing .avi files but the picture is perfect.
    I have installed the following: M-Peg 2 playback component, AVI Components and AC3 component.
    Does anyone know if I am missing anything or how I can fix this?
    Many thanks
    Garry

    Download and install Perian from http://perian.org/
    You should read this support page http://perian.org/#support in case you need to delete older codecs. In Macintosh HD/Library/Quicktime/ delete any files relating to DivX (Perian already has them). However it should be noted that Perian is not an internet plugin and will not play DivX files imbedded on a website. For that you will need the DivX Player browser plugin available from http://www.divx.com/divx/mac/

  • Cannot get email verification when trying to set up iCloud settings on my iPad.

    Cannot get email verification when trying to set up iCloud settings on my iPad

    I ignored my laptop for a couple of days and last night noticed that it had been updated by the cloud.
    I had added a test contact to my iPhone and it has appeared on outlook on my laptop.

  • HT1423 I cannot get a click when pushing in new module.  It clicks when I pull it out.  What am I doing wrong?

    I cannot get a click when putting in the memory.  It clicks when I pull it out.  Am I doing something wrong?

    Is it for sure the proper Memory?
    Does it look all the way in, even/level with existing RAM?

  • Get phone number when open tcp socket

    I can get phone number and other info of phone when mobile connect to server by http on GPRS, but can I get phone number when connect by tcp socket?

    When you open a tcp connection by socket from mobile phone to IP server, you use ip end to end connectivty. In fact, when you use GPRS support on your mobile phone this one have a public IP address used to establish an IP connection to an other IP device.
    If you want to get the phone number, two solutions :
    1/ you transmit the phone number like a datastream on you socket. But it's a static solution, because you must enter the mobile number as a input (through a textfield form or somethink like that)
    2/You take the phone number in the memory of your mobile phone (Agenda). But it's so compicated because that's depend of type of mobile. The memory design is dedicated mobile by mobile.

  • Network Error []: Cannot Get Host Name when running business rules

    Guru's
    We are getting the following error intermittently when we are running business rules (Planning Application >>Tools>>Business Rules) or running SmartView refreshes:
    Network error []: Cannot Get Host Name
    The following is then logged in the Essbase Application logs:
    Local/Application/Database/admin@Native Directory/Error(1042022)
    Network error []: Cannot Get Host Name.
    A quick look at the Essbase Error Messages Doc says it is a network error and we have to consult the network documentation. Unfortunately this is not very descriptive so we logged an SR with Oracle but we don't seem to be getting a resolution.
    The environment is 11.1.2.0 and the architecture is as follows:
    Server 1 - MS Server 2008 x64:
    Planning, Calc Manager, Foundation Services, Framework Web Services, EAS, APS, Web Analysis, FR Web Services
    Server 2 - MS Server 2008 x64:
    Essbase Server
    Server 3 - MS Server 2008 x64:
    Framework Services, FR Print Services
    We have tried doing the following:
    1. Put in the server host names into the hosts file on the Hyperion Servers
    2.  Applied the following TCP/IP settings on all the Hyperion Servers and one of the user machines as a test:
          - Added a new DWORD Value named TcpTimedWaitDelay and set it to 30.
         - Added a new DWORD Value named MaxUserPort and set it to 65534.
         - Added a new DWORD Value named MaxFreeTcbs and set it to 6250
    3. Confirmed that there are no packet drops by monitoring the server NICs so no packet loss could be the cause of this issue
    4. The Essbase Config file has the following settings:
    NETDELAY 2000
    NETRETRYCOUNT 2500
    Has anyone come across this issue and if you managed to resolve it, how did you go about it.
    Thanx

    Hi Rahul
    The issue is happening to a number of calcs so it it not one calc specifically. I will ask the functional consultants to enhance the logging in the business rules so that we can see if the issue happens on a specific member\block etc and yes we do use Xrefs
    We can run this as a calc in EAS without any issues and it's intermittent because this business rule runs 95% of the time in Planning Application >> Tools >>Business Rules without any issues.
    Thanks

  • HT4061 i updated iphone 4 with the software update ios7. i cannot get phone to restore i am stuck with a black screen or a screen with the apple ico that disapears and then the icon of itunes and the usb icon.  Itunes is not picking up my phone to even re

    cannot restore phone since update.  I tried to upload to itunes but itunes isnt picking it up. Phone is frozen with Itunes icon and the usb cord.  I tried some suggestions posted but it is still not restoring does anyone know how this can be fixed???
    Thanks

    Hello reneywacky,
    Thanks for using Apple Support Communities.
    For more information on this, take a look at:
    iOS: Unable to update or restore
    http://support.apple.com/kb/HT1808
    Connect your USB cable to your computer but not to the iPhone, iPad, or iPod touch until step 3.
    Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.If you cannot turn off the device using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the device turns off, release the Sleep/Wake and Home buttons.
    While pressing and holding the Home button down, connect the USB cable to the iPhone, iPad, or iPod touch. The device should turn on.
    Continue holding the Home button until you see the Connect to iTunes screen. When this screen appears, you can release the Home button:
    Note: If the image of a battery appears, let the device charge for at least ten minutes to ensure that the battery has some charge, and then start with step 2 again. If you don't see the Connect to iTunes screen, try these steps 1 through 4 again.
    iTunes should automatically open and display the following message:
    "iTunes has detected an iPhone in recovery mode. You must restore this iPhone before it can be used with iTunes."Note: If iTunes not open after two minutes, please open iTunes yourself.
    Use iTunes to restore the device.
    Best of luck,
    Mario

  • Getting phone signal into Logic via M-Audio

    To record phone calls on my land line, I got a Radio Shack Recording Control (43-228A), plugged it up, and set it to "Record." I plugged the 3.5mm plug into an adapter for 1/4 inch plug, which went into Input 1 on my M-Audio Fast Track Pro, from which point everything else is set as usual going into my Mac's FW. I made sure I had Input 1 selected, went to record as I spoke on a test call, and -- nothing but a hummmmmm. Just to be sure, I switched from line to mic input, and that didn't affect the hum.
    Does anyone know of what details I may have overlooked here to get the phone signal into Logic? FWIW, I also tried with the chintzy little $8 suction-cup on the handset, since it also has a 3.5mm plug. Not even any hum.
    I checked the usual suspects of "DUH" carelessness within Logic itself: making sure I matched the input to the M-Audio (tried both 1 and 2 anyhow), level up high, etc.
    Also, would anyone recommend other procedures for telephone recording? I'd rather stick with land lines instead of Skype or iChat, since not everyone I'll be calling to interview will have those. Suggestions?
    Thanks,
    c

    are the xp80 audio outputs wired into UL audio inputs?

  • TS3682 After updating cannot get phone to turn on. On screen it's has a pic to plug in to iTunes

    After updating iPhone via iTunes I cannot get the phone to turn on. Black screen with pic telling me to connect to iTunes

    Something went wrong with your update; you are in Recovery Mode.
    Follow step 1 to 6 closely to recover your iPad.
    http://support.apple.com/kb/HT1808
    Note: You may have to repeat the above a few times

  • Cannot get to debugger when Debug As - Junit Test in OEPE

    In Oracle Enterprise Pack for Eclipse, I created a JUnit (3 or 4) test case. When I attempted to Debug As -> Junit Test, I would get NullPointerException and cannot get to the debugger at all. However, there is no such problem in Ganymede (not OEPE). Is this a known problem for OEPE?
    The stack trace is:
    junit.framework.AssertionFailedError: Exception in constructor: testMapCustomer (org.apache.commons.logging.LogConfigurationException: org.apache.commons.logging.LogConfigurationException: java.lang.NullPointerException (Caused by java.lang.NullPointerException) (Caused by org.apache.commons.logging.LogConfigurationException: java.lang.NullPointerException (Caused by java.lang.NullPointerException))
         at org.apache.commons.logging.impl.LogFactoryImpl.newInstance(LogFactoryImpl.java:543)
         at org.apache.commons.logging.impl.LogFactoryImpl.getInstance(LogFactoryImpl.java:235)
         at org.apache.commons.logging.impl.LogFactoryImpl.getInstance(LogFactoryImpl.java:209)
         at org.apache.commons.logging.LogFactory.getLog(LogFactory.java:351)
         at org.springframework.test.ConditionalTestCase.<init>(ConditionalTestCase.java:50)
         at org.springframework.test.AbstractSpringContextTests.<init>(AbstractSpringContextTests.java:73)
         at org.springframework.test.AbstractSingleSpringContextTests.<init>(AbstractSingleSpringContextTests.java:80)
         at org.springframework.test.AbstractDependencyInjectionSpringContextTests.<init>(AbstractDependencyInjectionSpringContextTests.java:98)
         at com.cibc.wmfxr.pricing.processor.test.Junit38SybaseDaoTest.<init>(Junit38SybaseDaoTest.java:6)
         at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
         at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39)
         at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27)
         at java.lang.reflect.Constructor.newInstance(Constructor.java:513)
         at junit.framework.TestSuite.createTest(TestSuite.java:54)
         at junit.framework.TestSuite.addTestMethod(TestSuite.java:280)
         at junit.framework.TestSuite.<init>(TestSuite.java:140)
         at org.eclipse.jdt.internal.junit.runner.junit3.JUnit3TestLoader.getTest(JUnit3TestLoader.java:102)
         at org.eclipse.jdt.internal.junit.runner.junit3.JUnit3TestLoader.loadTests(JUnit3TestLoader.java:59)
         at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:445)
         at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:673)
         at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.run(RemoteTestRunner.java:386)
         at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.main(RemoteTestRunner.java:196)
    Caused by: org.apache.commons.logging.LogConfigurationException: java.lang.NullPointerException (Caused by java.lang.NullPointerException)
         at org.apache.commons.logging.impl.LogFactoryImpl.getLogConstructor(LogFactoryImpl.java:397)
         at org.apache.commons.logging.impl.LogFactoryImpl.newInstance(LogFactoryImpl.java:529)
         ... 21 more
    Caused by: java.lang.NullPointerException
         at org.apache.commons.logging.impl.LogFactoryImpl.getLogConstructor(LogFactoryImpl.java:374)
         at org.apache.commons.logging.impl.LogFactoryImpl.newInstance(LogFactoryImpl.java:529)
         at org.apache.commons.logging.impl.LogFactoryImpl.getInstance(LogFactoryImpl.java:235)
         at org.apache.commons.logging.impl.LogFactoryImpl.getInstance(LogFactoryImpl.java:209)
         at org.apache.commons.logging.LogFactory.getLog(LogFactory.java:351)
         at org.springframework.test.ConditionalTestCase.<init>(ConditionalTestCase.java:50)
         at org.springframework.test.AbstractSpringContextTests.<init>(AbstractSpringContextTests.java:74)
         at org.springframework.test.AbstractSingleSpringContextTests.<init>(AbstractSingleSpringContextTests.java:80)
         at org.springframework.test.AbstractDependencyInjectionSpringContextTests.<init>(AbstractDependencyInjectionSpringContextTests.java:98)
         at com.cibc.wmfxr.pricing.processor.test.Junit38SybaseDaoTest.<init>(Junit38SybaseDaoTest.java:6)
         at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
         at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39)
         at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27)
         at java.lang.reflect.Constructor.newInstance(Constructor.java:513)
         at junit.framework.TestSuite.createTest(TestSuite.java:54)
         at junit.framework.TestSuite.addTestMethod(TestSuite.java:280)
         at junit.framework.TestSuite.<init>(TestSuite.java:140)
         at org.eclipse.jdt.internal.junit.runner.junit3.JUnit3TestLoader.getTest(JUnit3TestLoader.java:102)
         at org.eclipse.jdt.internal.junit.runner.junit3.JUnit3TestLoader.loadTests(JUnit3TestLoader.java:59)
         at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:445)
         at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:674)
         ... 2 more
         at junit.framework.Assert.fail(Assert.java:47)
         at junit.framework.TestSuite$1.runTest(TestSuite.java:90)
         at junit.framework.TestCase.runBare(TestCase.java:130)
         at junit.framework.TestResult$1.protect(TestResult.java:106)
         at junit.framework.TestResult.runProtected(TestResult.java:124)
         at junit.framework.TestResult.run(TestResult.java:109)
         at junit.framework.TestCase.run(TestCase.java:120)
         at junit.framework.TestSuite.runTest(TestSuite.java:230)
         at junit.framework.TestSuite.run(TestSuite.java:225)
         at org.eclipse.jdt.internal.junit.runner.junit3.JUnit3TestReference.run(JUnit3TestReference.java:130)
         at org.eclipse.jdt.internal.junit.runner.TestExecution.run(TestExecution.java:38)
         at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:460)
         at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:673)
         at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.run(RemoteTestRunner.java:386)
         at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.main(RemoteTestRunner.java:196)

    Thanks. I tried it with the downloaded junit-4.6.jar and got the following stack trace. Now I wonder I should try it with the Junit bundle in the SpringSource Enterprise Bundle Repository since OEPE integrates the Spring OSGi Bundle. If this is the right idea, could you let me know how to install the Junit bundle in OEPE? Do I just add it to bundles.info? There are already a few lines for org.junit in bundles.info. What should I do with them? Thanks a lot.
    java.lang.ExceptionInInitializerError
         at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
         at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39)
         at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27)
         at java.lang.reflect.Constructor.newInstance(Constructor.java:513)
         at org.junit.internal.builders.AnnotatedBuilder.buildRunner(AnnotatedBuilder.java:31)
         at org.junit.internal.builders.AnnotatedBuilder.runnerForClass(AnnotatedBuilder.java:24)
         at org.junit.runners.model.RunnerBuilder.safeRunnerForClass(RunnerBuilder.java:57)
         at org.junit.internal.builders.AllDefaultPossibilitiesBuilder.runnerForClass(AllDefaultPossibilitiesBuilder.java:29)
         at org.junit.runners.model.RunnerBuilder.safeRunnerForClass(RunnerBuilder.java:57)
         at org.junit.internal.requests.ClassRequest.getRunner(ClassRequest.java:24)
         at org.eclipse.jdt.internal.junit4.runner.JUnit4TestReference.<init>(JUnit4TestReference.java:28)
         at org.eclipse.jdt.internal.junit4.runner.JUnit4TestClassReference.<init>(JUnit4TestClassReference.java:24)
         at org.eclipse.jdt.internal.junit4.runner.JUnit4TestLoader.createTest(JUnit4TestLoader.java:40)
         at org.eclipse.jdt.internal.junit4.runner.JUnit4TestLoader.loadTests(JUnit4TestLoader.java:30)
         at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:445)
         at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:673)
         at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.run(RemoteTestRunner.java:386)
         at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.main(RemoteTestRunner.java:196)
    Caused by: org.apache.commons.logging.LogConfigurationException: org.apache.commons.logging.LogConfigurationException: java.lang.NullPointerException (Caused by java.lang.NullPointerException) (Caused by org.apache.commons.logging.LogConfigurationException: java.lang.NullPointerException (Caused by java.lang.NullPointerException))
         at org.apache.commons.logging.impl.LogFactoryImpl.newInstance(LogFactoryImpl.java:543)
         at org.apache.commons.logging.impl.LogFactoryImpl.getInstance(LogFactoryImpl.java:235)
         at org.apache.commons.logging.impl.LogFactoryImpl.getInstance(LogFactoryImpl.java:209)
         at org.apache.commons.logging.LogFactory.getLog(LogFactory.java:351)
         at org.springframework.test.context.junit4.SpringJUnit4ClassRunner.<clinit>(SpringJUnit4ClassRunner.java:63)
         ... 18 more
    Caused by: org.apache.commons.logging.LogConfigurationException: java.lang.NullPointerException (Caused by java.lang.NullPointerException)
         at org.apache.commons.logging.impl.LogFactoryImpl.getLogConstructor(LogFactoryImpl.java:397)
         at org.apache.commons.logging.impl.LogFactoryImpl.newInstance(LogFactoryImpl.java:529)
         ... 22 more
    Caused by: java.lang.NullPointerException
         at org.apache.commons.logging.impl.LogFactoryImpl.getLogConstructor(LogFactoryImpl.java:374)
         ... 23 more

Maybe you are looking for

  • Deactivate creation of new next inspection date on re-GR

    Our user created GR (MIGO) against a PO and subsequently a new batch with a next inspection date was created based on inspection interval set to 730 days. The user agin after a few days did GR against the same PO and the next inspection date was agai

  • System to consider only regular vendors in rating

    Dear Gurus, During vendor rating at present system is considering all vendors who were not supplied for entire quarter(say).ie, system now showing the vendors who supplied one time, un supplied vendors. but the requirement is system has to consider o

  • WAD - Link to open PDF file

    Hello, I created an application in WAD - some tables, some buttons etc. I need to add a link (or button, not the matter), where user can click to open attached PDF file. PDF can be stored anywhere (i.e. in "Documents" in RSA1 or as a regular file on

  • Want to see English app store reviews again

    In the past you could (only) see English reviews in the iOS app store even if you were in the national (in my case Danish app store). Now it is ONLY possible to se Danish reviews, which are very few (with a population of 6 Mio people). Is it not poss

  • So iCal won't sync as I've had to change my gmail password.  Anyone figured out how to fix this?

    So iCal won't sync now as I've had to change my gmail password.  Anyone figured out how to fix this?