I cannot print to my photosmart 7510 when connected to work with VPN

When I try to print to my printer while connected to VPN, I get an error that the software could not communicate with my printer. The IT department where I work has configured the VPN so that traffic to my local LAN is allowed (does not go through the tunnel). I had no problem printing to my old printer when connected with VPN (old printer was a photosmart 2510 connected via wireless network).
These symptoms lead me to believe that the printer software is attempting to connect to the internet when I send a print job to my local printer. Why is it doing that? What settings do I need to change to make it stop so that I can print while connected with VPN?

But I don't understand why the internet connection that my printer has comes into play when I'm sending a print job from my PC to my printer over my local network. I am not using the web services at all for that particular function.
At least I shouldn't be - I don't know what the HP print software installed on my PC is doing under the hood. The software shouldn't have to access the internet to send a print job locally. Nor should my printer have to access the internet in order to receive the print job from my PC.
What exactly is the printer or the print software accessing the internet for when I send a print job from my PC to my printer over my local network?

Similar Messages

Ipod touch for Christmas, but cannot get started: after installing itunes, when connecting to my laptop I get no instruactions, just the error message "This iPod cannot be used because the Aplle Mobile Device service is not started". Any suggestions???

ipod touch for Christmas, but cannot get started: after installing itunes, when connecting to my laptop I get no instruactions, just the error message "This iPod cannot be used because the Aplle Mobile Device service is not started". Any suggestions???

Jennifer...
Follow the instructions here > iPod touch: How to restart the Apple Mobile Device Service (AMDS) on Windows

TS3999 when will iCloud work with outlook 2013?

when will iCloud work with outlook 2013?

I have been running Outlook 2013 for a couple of weeks now using W8 64bit.
It works with iCloud and is a little flakey, what I've found.
1. 4 X Junk Folders.
2. Some emails cannot be moved into saved folder, saying message has changed, but opening in outlook safe
mode allows move.
3. Sent Items (this computer only) and Sent Messages, so you have to move emails from Sent Items to Sent
Messages if you want them to sync across devices.
4. Icloud control panel say's there is a problem and not syncing but it is no problem.
I can live with the bugs, but I wish the last icloud update would have corrected the issues.

Bugged audio playback? When I start working with more than 1 audio track.

Hi!
I have been using premiere elements 12 for editing FullHD videos.
Brand new for me just bought it like 2 weeks ago.
Now during the last couple weeks I have had this MAJOR proglem with editing the audio.
This problem is headache and turns my simple editing into almost impossibilites.
I have had this problem with all my projects. _ALL_
Usually the problem seems to appear when I want to start working with several audio tracks.
At somepoint my projects just get ruined, I simply cannot hear the audio tracks.
The audio starts to disapear randomly from all the audio tracks.
It is not only playback problem. When I exported the video, the audio was partly missing, same as the project.
I have tried to look help on forums and search all what I could find, but havent been able to solve this.
Small fix has slightly helped:
I export audio to single track and bring it back to project. This works but I still usually have more editing to do.
I simply cannot understand why the playback disapears, I fear it is a bug.
I found lot of earlier version problems on people with similar type of problems, but no help for this version of program.
To solve the matter I have changed my audio setting in PE12.
Tried Premiere Elements WDM Sound and ASIO4ALL V2, but same problem on both.
I have looked up that my audio playback device and PE12 matches, and are not muted, and volumes maxed.
I have deleted my C:\ appdata\roaming\adobe premiere elements & premiere elements 12 folder preferences.. not helping..
I press the update pretty much everyday hoping for new version.. But yes, program keeps telling me its the latest.
I usually only work with 3 audio track maxinum. And I am doing really the most basic stuff here..
I have set all my audios to foreground and it has given me best results, but it does not seem to take the problem away as at somepoint randomly my audio playback is missing again, randomly across the playback.
Please anyone? I am feeling hopeless here.
Info on my computer:
Operating system: Win7
Processor: AMD Phenom(tm) x4 955 processor 3.20 GHz
memory (RAM): 4GB
system: 64bit
<moved from downloading, installing, setting up forum by mod- kglad>
Message was edited by: kglad

First of all, thank you for replying my message!
I will go and try to answer best I can.
Source media properties:
Progressive frame rate, I record this from a game.
Recording program: dxtory
codec: Lagarith Lossless codec
Format: avi
Frame width: 1920
Frame height: 1080
Data rate: 1990656kbps
total bit rate 1992192kbps
Frame rate 30/frames/seccond
Audio of video properties:
Codec: PCM
Format: 16bit, stereo
Bit rate: 1536kbps
Channels: 2(stereo)
Audio sample rate 48 kHz
In addition to that I use wav files for music and narrate
Music files sizes 20-50mb
bit rate: ~1411kbps
In total sizes of audio involved is usually something like 300mb
What are you or the program setting as the project preset in the new project dialog. See Edit Menu/Project Settings/General and its Editing Mode, Timebase, and Frame Size readings.
I opened new project and this is what i got:
Editing mode: HD 1080i
Timebase: 25,00 frames/second
Frame size: 1920 x1080
Audio is 48000 Hz
(I dont know how to change these, btw. Program don't seem to let me change editing mode.
I also looked up my most recent project and found these settings:
Editing Mode: DSLR
Timebase: 30,00 frames/second
Frame size: 1920 x1080
..and same audio settings
Do the problems persist if you start a new project? Do you find the audio problems develop when the Timeline content is fairly well developed or can the problems occur when there a minimal amount of content of those tracks? Let us look at the size and duration of this project.
Yes, I have had this problem with all my projects. Sometimes it goes away tho, just enough for me to work bit more. My work progress usually starts by clipping the video material, like 1h material to 8minutes in clips. After that I want to work with audio tracks, and here problems start! When I start working with more than 1 track, so the problem is at later stage. To fix the problem a small fix I have used, I export audio like music and effects tracks together to 1 wav and bring it back. After that, I start working with narrate track. To describe the problem with audio:
Audio Randomly starts to disapear when I playback, and can also be gone if I export the video out.
My source videos total size are usually within 80Gb max limit and audio edit material 300mb total.
In my last project my biggest source video was 47GB and leingth of 1h 4m, in addition to that I had 3 smaller videos, sizes of 1GB, 1,54GB and 300MB.
Is there any evidence that you are accidentially moving the audio track rubberband to alter the audio volume. That rubberband is the orange line that runs horizontally through the middle of the audio clip when you are looking at the wave form display style of that audio track. The rubberband represents audio volume.
No, audio volumes might have been adjusted in my tracks but they are present. The problem is usually like ~2-5seconds, a random audio track can be heard (like music or narrate) or just no sounds at all. This makes it very difficult to work with the audio. Also I gotta say that this problem starts by simply having the 2-3 audio tracks.. In my recent project the only adjustment I used to edit the audio was fade in/out.
I don't have any other audio problems with any other programs.
I am more than happy to provide more information if needed. I hope this information helps.
In addition I can say that when I close Adobe Premiere Elements 12, it crashes. No idea why.
I have also looked up my firewall settings, anything involved adobe and premiere..
In addition some effects like HD text templates make "Adobe Media Core CS6" crash. I tend to just not use em, or if I need em, I add em at end of the edits.
I hope this helps, I would really like to solve this problem.
Thank you alot for taking the time to answer! I welcome anyone to help mee too! Please giev links to similar problems too. Thank you everybody!

Does "erase when connecting" really work?

A few weeks ago, my MacBookPro got stolen :-((
Of course, I had registered it with 'Find My iPhone', and, immediately after it got stolen , I requested in 'Find my iPhone' an erase as soon as it would connect to the internet.
However, so far, iCloud reports that it has not yet connected to the internet.
So I was wondering, whether that feature actually works, or whether it is possible to circumvent the erase.
Is it possible to change the serial number of a Macbook ?
Or is it possible to connect it to the internet such that Apple cannot erase it?
Best regards,
Gabriel.

Hi GabrielZ,
Very sorry to hear you had your macbook pro stolen !
All I can say is that I heard the "erase when connected" Does Work !
Good luck with everything

When trying to work with Agilent 34401A multimeter (serial RS-232 connection), HP34401A Getting Started.vi gives always the message: "Error 1073807369 occurred at Old VISA Open ".

Baud rate and parity are set correctly, RS-232 cable is also connected correctly. My QuickBasic program has no problems to read and write to the Multimeter. It is obviously a software problem: the same error is persistent if I disconnect RS-232 cable.
I downloaded NI-VISA 2.6 for Windows 95/98/NT/ME/2000/XP frorm digital.ni.com and installed it. But it did not help.
Thank you in advance
Best regards
Alexei Soloviev

Hi Steve
I have problems with the 34401A and serial communication. Do you remember
where the error was in the code ?
Thanks
Klaus
wrote in message
news:[email protected]..
> Alexei,
> This may or may not help, I was tasked to do something similar
> recently and found an error in their driver. The GPIB VISA worked
> fine, but when I tried it on serial it played up. There was an errant
> carriage return (or CR/LF I can't remember). GPIB liked one and Serial
> liked the other. It always amuses me that we never have problems with
> Quickbasic!.
> If you want me to dig deeper give me a shout.
>
> Steve Watts
>
> On Thu, 24 Jan 2002 06:16:55 -0800 (PST), "Alexei V. Soloviev"
> wrote:
>
> >When trying
to work with Agilent 34401A multimeter (serial RS-232
> >connection), HP34401A Getting Started.vi gives always the message:
> >"Error 1073807369 occurred at Old VISA Open ".
> >
> >Baud rate and parity are set correctly, RS-232 cable is also connected
> >correctly. My QuickBasic program has no problems to read and write to
> >the Multimeter. It is obviously a software problem: the same error is
> >persistent if I disconnect RS-232 cable.
> > I downloaded NI-VISA 2.6 for Windows 95/98/NT/ME/2000/XP frorm
> > digital.ni.com and installed it. But it did not help.
> >Thank you in advance
> >Best regards
> >Alexei Soloviev
>

Hello, I have a Mac computer with NVIDIA 750M dedicated graphics card and monitor EIZO but the problem was there when I was working with Windows and Acer monitor. When I open a file from Camera Raw in PS this is smaller than the screen so I double-click w

Hello, I have a Mac computer with NVIDIA 750M dedicated graphics card and monitor EIZO but the problem was there when I was working with Windows and Acer monitor. When I open a file from Camera Raw in PS this is smaller than the screen so I double-click with the tool "hand" to fit on the screen, but the picture loses sharpness and becomes blurry. If you magnify the image even only slightly with the tool "zoom" the picture comes back clear. In Camera Raw instead is always sharp. I solve the problem by turning off the graphics card in PS but often use plugin that need the graphics card otherwise the processing time is much longer. I ask for help.
Thanks.

Hello, I have a Mac computer with NVIDIA 750M dedicated graphics card and monitor EIZO but the problem was there when I was working with Windows and Acer monitor. When I open a file from Camera Raw in PS this is smaller than the screen so I double-click with the tool "hand" to fit on the screen, but the picture loses sharpness and becomes blurry. If you magnify the image even only slightly with the tool "zoom" the picture comes back clear. In Camera Raw instead is always sharp. I solve the problem by turning off the graphics card in PS but often use plugin that need the graphics card otherwise the processing time is much longer. I ask for help.
Thanks.

When I'm working with my Ipad it locks on its own and every several minutes I have to unlock it. Help please

When I'm working with my Ipad it locks on its own and every several minutes I have to unlock it. Help please

If your iPad was work provided there may be options that they locked out. For example, a privately owned device can be set to never auto lock (last I knew anyway) but it's not uncommon for work or school provided devices to not have the 'never' option.

Re: Not getting audio from TV when connecting MacBook Pro with all correct cables.

How do I get audio from the TV when connecting MacBook Pro with all the correct cables?

Hi Lynn,
If you're positive you have the correct cables, and positive they work, they must be plugged into an input on the TV made for that purpose, then that input must be selected on the TV's menu.

HT5105 How can you do picture in picture when you are working with a Multicam clip?

How can you do picture in picture when you are working with a Multicam clip?

Im doing a drumming music video and with the multi cam clip all the angles are nicely sync'd top the audio.
Problem is if i want to have 3 angles on top of the main shot, im gonna have to re-sync them all to get them to line up manually. If i could use the multi cam clip they will already be aligned
Thanks for trying to help appreciate, hoping someone has some multiclip knowledge and will be able to tell me if yay or nay.

Quick Time screen capture freezes when i'm working with Modo 3D. Any solution?

Hi guys, When I'm working with Luxology Modo, Quick Time screen capture freezes every time on Mac OS X Mavericks. When I'm doing some operation in Modo, like slice geometry per exemple, QuickTime crashes. I must force quit quicktime and when I relauch the application, the screen capture opens but screen capture ends at the time when I cliked on the Modo slice operation. It's frustrating because I can't do nothing with screen capture. I tried other screen capture applications but the problem persists! When I was using Snow Leopard Quick Time works very well!! Do you have some resolution for this problem? Regards, César.

I'm using OS X Mavericks as well, and it seems like the same thing happens when I try to type in MonoDevelop, part of the Unity package. Unity works fine, it only seems as though I can't screen record typing in MonoDevelop. It looks like it's still recording, it just has the rainbow wheel of death after I try to finish out the Quicktime. I left it up for several days and ignored it, but it still didn't finish. I finally had to force quit it and reopen it and when I did it opened up the temporary file of the video I was recording, but it stopped whenever I started to type into the MonoDevelop interface. The first time it let me save the video to the desktop. The second time, the time which I left it open for days, it would not let me save it, on command-S or on exit. I don't know exactly what's wrong, but I believe that you know as much as I do. Please post a reply if you need any more information or have a fix.

Olympus xz-1 camera when connected to ipad2 with supplied ubs cable into apple usb to 30pin adapter it prompts the ipad to display a message like " this device draws too much power to charge" and then i can go no further!

olympus xz-1 camera when connected to ipad2 with supplied usb cable into apple usb to 30pin adapter it prompts the ipad to display a message like " this device draws too much power to charge" and then i can go no further! if i take the card from the camera and put it into the card to 30pin adapter and plug that into the ipad no problems. if i connect the camera with supplied usb cable to desktop imac , no problems. if i connect my olympus slr to the ipad using its usb cable into the apple usb to 30pin , no problem . very frustrating , i don't want to always have to take the card out of the camera to down load photos to the ipad2,IDEAS?

I'd ask that on the iPad forum.
https://discussions.apple.com/community/ipad

I have a G4 with OSX 10.2 and my printer died. New printers only seem to work with 10.4.11 and newer - can I upgrade my G4 enough to use a new printer?

I have a G4 with OSX 10.2 and my printer died. New printers only seem to work with 10.4.11 and newer - can I upgrade my G4 enough to use a new printer?

Aha!
Well in outer Mongolia ASAP means something totally different and involves weaving tent fabric from camel hair so that has taken me a bit of time.... However if you have the patience of a saint and the compassion of Mother Theresas' more helpful sister then....
So it would appear I have the following supersonics:
OSX 10.2.1
60 Gb HD
G4 dual processor 1GHz
Now the critical issue here is that I get the computer up to speed enough to be compatible with a modern photo printer - which I think needs to be 10.4.11 or even 10.5
Any assistance would be most gratefully and humbly recieved.

My mac get very hot when I'm working with it is it normal??

my mac get very hot when I'm working with it is it normal??

When posting in Apple Communties/Forums/Message Boards.......It would help us to know which MBP model you have, which OS & version you're using, how much RAM, etc. You can have this info displayed on the bottom of every post by completing your system profile and filling in the information asked for.
***This will help in providing you with the proper and/or correct solutions.***
============
Please detail ALL you have done so far in the way of troubleshooting? Need this info to avoid the been there done that scenarios.

HP Photosmart 7510 - loose connectivity when using Ethernet cable

Need help!
I have an HP Photosmart 7510 all-in-one printer connected to my home network via wireless.
I have 1 Windows7 laptop which successfully connects to the printer via the home Ethernet network (laptop connected via cat5) - so the overall system appears to be working fine on Windows.
I also have 1 MacMini running OS X 10.7.5 which can ONLY print/scan if the Ethernet connection is UNPLUGGED from the MacMini (thus forcing me to use my very poor and unreliable wireless signal).
As soon as I plug in the Ethernet cable to the MacMini I loose all connectivity to the printer. I have confirmed the Ethernet cable is good - as it works fine with my Windows7 laptop.
Has anyone figured out why I cannot use the physical Ethernet connection to communicate with the HP Photosmart?
Thanks!

Just making sure, you're running the Ethernet cable from the printer to the router, then running another cable from the router to the Mac, correct?
Have you added the printer's queue to the Mac once the Ethernet cable is connected, or does it not show up in Print and Scan?
I am a printer tech for HP.

I cannot print to my photosmart 7510 when connected to work with VPN

Similar Messages

Maybe you are looking for