I contrloling an RTX equiped stage in a non-queue mode, but I think lab view is adding on a queue about 3 high

The problem is that im using Image recognition to control the movement, and i am sending a command to move to a point based of the image, but before this is fed to the stage, another image recognition is performed and this is going to the stage as well, so everytime im overshooting about 3X the distance, because before the stage is moved. I am using a non-queue mode with this stage, which should discard any in action command, for the next, but i dont think this matters because i think labview is late to send them to the stage, and it finishes the moves before it gets them from labview. Besides for playing with delays (ive tried but, i really want a smooth program, and this isn't happening with delay adjustment) how might i keep this queue from building up in labview?

Russell,
I'm not sure I completely understand your question. From what I can gather you are doing some image processing on some event and based upon the results of that processing you are sending a command to your motor to do some type of move. The problem is that your motion commands are not executing in the the manner you would like (ie timing problems). Is ths a correct assessment of the problem?
A few other questions:
1. Are you using the National Instruments drivers for Vision and Motion?
2.What are the software versions you are using?
3. What type of image processing are you doing?
4. What type of move are you having your motor perform?
5. What specific VIs are you using to send the commands to the motor?
6. What is the "non-queue mode" you are referring to?
6. What are your timing constraints?
Thanks,
S. Arves S.
National Instruments
Applications Engineer

Similar Messages

HT1414 I have iphone 4; tried to sync it said I need to update software so I clicked ok - it then said I need to restore and did above got to stage 3, clicked restore and update, but it comes up with an error saying iphone cannot be found Please help!!!

I have iphone 4; tried to sync it said I need to update software so I clicked ok - it then said I need to restore and did above got to stage 3, clicked restore and update, but it comes up with an error saying iphone cannot be found Please help!!!

Dear Jody..jone5
Good for you that can't update your iphone because I did it and my iphone dosen't work for example I can't download any app like Wecaht or Twitter..
Goodluck
Atousa

ESP 301 Controller (Newport stages) via Lab view

Does any one have experience with ESP 301 Controller(Newport Stages) control via labview ?
I am trying to find if there are any known issues and things I should be aware of before we start the project.
Thanks

I have only worked with the ESP300 in the past and that was quite a painful experience. It's GPIB interface works rather unreliably unless tickled always in a very specific way. Even then there are still occurrences where the motion axises suddenly seems to behave in an unexpected way, with settings that were absolutely fine before. I would hope that they improved the firmware of the ESP301 significantly but I can't vouch for that.
Rolf Kalbermatter
CIT Engineering Netherlands
a division of Test & Measurement Solutions

Disatisfied notebook owner with an aftersales support

Is Toshiba making its customers victims of its success? Generally reliable products resulting in a poor aftersales support?
I have been using laptops for business and pleasure for several years without fault and as the satisfied owner of Toshiba TVs and other electronic equipment decided to buy one of their laptops.
I paid in full for a new L series and after 6 months of normal use it stopped charging. Felt like the pin in the machine the charger plugs into was loose.
I contacted the supplier and they accepted it would need repairing and after apologising for my inconvenience, were happy to carry it out but pointed out it would probably be repaired quicker if I contacted Toshiba and asked them to carry out the repairs.
So I did. And it just goes down hill from there. First mistake was mine, not registering the warranty. So I tried to do that. But I'd bought on line and as my six month old machine was apparently manufactured 11months and 28 days ago, I had to provide evidence of purchase. Offering to email a copy of my bank statement showing the purchase date, price and supplier was not satisfactory.
This meant contacting the supplier in London during office hours, the same as I work, and therefore not easy to do. They emailed me a copy of this and I then spent two nights trying to forward this to Toshiba for verification.
This I eventually did and the next day during another lunch hour, rang to arrange collection. I was put though to a repair tech who said yes, we can repair this but his manager told him it would not be a warranty repair, regardless of the fact it was only six months old. I rang off, not happy.
Next day, I rang back, spoke to some one else and was able to arrange for collection, having been told that if, in their view, it was my fault it was not working I'd have to pay for repairs and the return fee of almost 80. These threats, and thats how i view them, were given regardless of my statement that it was used normally like all the other ones I'd used for years and was less than 6months old.
The following Monday, it was not collected as agreed. It was collected on Tuesday and not packed by the collection company as I was told, I did it as the driver did not know how the box worked. Neither did I but I did it. And, as instructed, I did not include the charger unit.
It was returned, unannounced, at the beginning of the third week, over four since it stopped working. By way of explanation, a two line note was found behind the address label saying the DC In lead changed, battery tested.
Happy just to have it back, I took it home, plugged it in and it doesn't work. Looks like the charger is faulty as well as the pin. I am so not looking forward to tring to get this bit sorted.
Sorry this is so long winded but this is my experience of Toshiba's after sales service. I can't help but wonder if I am the only dissapointed, disallusioned and angry customer out there and am curious to hear of the treatment others have experienced.

Hello
At first sorry to hear you have this negative experience but in such situation you must be a little bit realistic. It is well known that notebook manufacturers or any other manufacturer by different products recommend product registration and it should be done pretty quickly and not 6 months later. Last month I bought pretty expensive vacuum cleaner with 5 years warranty and I have registered immediately. Now if something goes wrong I can be sure it will be repaired for free.
Anyway, it is nice to hear you made one big mistake.
I use two Toshiba notebooks and I have registered both of them after first start immediately when this option was offered even before operating system started for the first time.
Unfortunately I cannot help you with your case but just want to write about mine experiences.
After just one month of usage motherboard on my Satellite A300 died. I just wanted to connect external HDD but some electric shock destroyed whole power supply electronic and my external HDD was dead too.
I have contacted Toshiba service in my country and next day I was in the shop. I didn't want to be arrogant or make some kind of pressure and just kindly asked if this can be fixed as soon as possible.
You will not believe me 7 days later I got my notebook back with new motherboard.
I was so happy so I paid coffee for two technicians who have managed all this.
One more time sorry to hear you had bad luck with all this but I think it is not to give general statements about service worldwide. Maybe the guys in my country are more motivated to do good job. ;)

Macbook pro a/c adapter not charging

The Apple a/c adapter that charges the Macbook Pro (daughter's computer) does not charge the computer nor does the green light on the cord light up. Was going to test someone's else Macbook Pro adapter to see if the issue is with the original adapter and not the internal battery. Assume the adapter just needs to be replaced. Not for sure if there was some type of electrical surge or problem that caused the adapter to go bad.

Hi
Had the problem of "battery not charging" on Macbook Pro 2006
Charger connecter lit up green
It was very new non apple battery from OWC
Looked at the System Profile only 16 cycles on the battery
AC charger was shown as "connected"
Battery showed up so not a problem with poor connection or not properly inserted (I had tried taking the battery in and out several times) but the profiler said "Charging: No"
Charger worked on another Macbook so that wasnt the problem
I tried the SMC reset where you sleep, shutdown, take out the battery, press power supply for 5 secs, reconnect AC, reinsert battery etc - No luck
Then I read the SMC also controls the sleep wake cycle and lid closure.
I cant exactly remember what I did because I was so ****** off by this stage and starting to lose concentration but I think I closed the lid and let the computer go to sleep and then opened it again to rewake.
After doing this 3 times the bloody thing now shows the battery is charging
A bit random I know but saved me having mental breakdown
I would love to know if this helps anyone else!

Possible iFreeze(TM) workaround

Hi there
I know there are already lots of threads on this - but I think it's worthwhile adding one for possible workarounds.
I had the freee issue from day one on - but fortunately not as bad as others - more of a random nature. After reading lots and lots of discussions I found the following workaround I can live with for the moment:
As soon as I notice the dreaded graphic glitches I restart the computer, zapping the PRAM 5 times (Hold down alt-cmd-p-r until you hear th sixth chime). After that the computer works flawlessly for days, sometimes weeks.
Last friday I made the update to Leopard - instant freeze. I did reset, zap - everything ok. I installed 1.3 update - instant freeze again reset, zap - and working like a charm since then.
I have no idea if this works for you too - but it's worth a try.
This is my theory on why this might work: Some people claiming to be close to ATI state its the initialization process of the graphics card that goes wrong. Maybe on some iMacs the chance of failure is much higher than on others. Zapping the PRAM at the init stage might change the timing of the whole process to give it a higher chance of succeding. (Of course, everything pure speculation on my side)
But whatever it is - *Apple, fix this ASAP or tell us at least what's wrong!*
Cheers
iWolf

Zapping PRAM multiple times accomplishes nothing. Zapping it once is all that should be required. If that doesn't fix it, zapping it twice isn't going to improve the situation. There isn't any information that is kept in PRAM after the first zap.
The freeze problem is a driver issue with the Radeon card (or in some cases, just a bad card). This is not the only freezing problem related to Radeon cards - if you search around on the web and these forums for "ASIC hang" or "mac display freeze", you'll find this is a fairly common problem in any Apple computer that uses graphics cards from ATI. While the problem currently being reported by some Alu-iMac users is a very serious and widespread issue, it is by no means isolated to the 2600 HD card. I've even read a few reports of XServes (the one computer you would think Apple would want to be as absolutely problem-free as possible) freezing up exactly like the latest iMacs - and guess what? The system log file shows an "ASIC Hang Log," and the card in the XServe is made by... drum roll please... ATI. Cards from ATI just basically **. While nVidia isn't perfect, there are far, far fewer problems reported from those cards.
The disappointing thing is that the only way to get a choice in video cards in a desktop system from Apple is to buy a Mac Pro. Even on those computers, I've read numerous reports about all manner of problems with graphics (freezing, artifacts, etc. - sound familiar?) when Leopard is installed on a Mac Pro that has a ATI card. Fortunately, the Mac Pro can be configured with a nVidia card, and of course even if you have a problem later on down the line, you always have the option of just popping the bad card out and popping a new one in.
Since the performance of the iMac has been boosted so as to be a serious contender for a tower desktop replacement for anyone but a horsepower-hungry professional user, the philosophy behind the iMac design needs a serious re-think by Apple. There needs to be some options available to the buyer - like, for example, an option in which graphics card to use. I want those kind of options, but I certainly don't need the kind of horsepower in a Mac Pro to justify purchasing one just to get some configurability with my computer. Apple desperately needs to add another computer line to its offerings: call it, maybe, just the Mac. The iMac and Mac Mini are for web surfers, light gamers, and all-around home users, the Mac is a more configurable but still attractive tower system that is based on the same motherboard/processor setup as the iMac, but has the configurability (PCI slots, removable hard drive, space for an extra internal drive, a removable optical drive) a hobbyist or more serious gamer wants and needs, and the Mac Pro is for the true horsepower-hungry professional (or for the gamer who has more money than brains!).

Thinkpad T510 Random Bluescreens

Hi all,
I've got a Thinkpad T510 (4313-CTO) that I am having trouble with. It is only about a month old.
What happens is, when I boot into Windows (including Safe Mode) I get a BSOD at varying stages of the bootup, sometimes I can use the machine for 3 or 4 minutes, and sometimes it just BSOD's at the Windows Loading screen.
The fact that it happens at various stages, in normal and safe modes, makes me think that it is a hardware issue. I'm not sure if this series (or any) of Lenovo's machines used the Sandy Bridge lot, but it is possible that it could be the problem.
It doesn't bluescreen in Acronis TrueImage that I loaded from the bootable CD.
[IMG]http://i55.tinypic.com/167mf0p.jpg[/IMG]
(Direct Link: http://tinypic.com/r/167mf0p/7)
Any help that anyone can provide is appreciated.

ShaunSforza, welcome to the forum,
you don't mention which version of Windows you have installed, or if it's a factory or manually installed version of that system. Maybe you could add this information.
Thanks
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

AppleCare Keeps Your Hard Drive?

My wife has a MacBook which stopped working. She has Apple Care. Took it in to the local Apple Store, a week later it's ready to pick up.
They said the hard drive died and they replaced it. She asked to have the old drive back, just in case, as there are photos etc... that weren't backed up and has hope they may be recoverable.
They absolutely refused to give her back the dead drive, the explanation being that Apple makes them send replaced hardware in as part of the Apple Care agreement "or they wouldn't make any money off Apple Care and couldn't afford to offer it anymore."
It's after hours here so I can't talk to an Apple Customer Service Rep.
It seems like madness that it should be my concern if Apple can profit from their warranty service.
Anyone else had this happen to them? They told my wife she should have made recovery attempts before bringing it in, but perhaps they could have told us that when we dropped it off? Keep in mind we didn't even know what was wrong with it at the time...
It just seems to me that the laptop and everything in it was ours at time of purchase, they have no right to hold onto it just because they were forced to honor a warranty claim.

Kappy wrote:
The hard drives are not returned when they are replaced. The dead drives will be returned to their manufacturer where they will be refurbished if possible. However, if the bad drive is accessible you can ask the Apple store that replaced the drive to transfer your data to the new drive. They should be able to do that for you. I've even heard that they may be willing to recover data from a corrupted drive if data are recoverable. I don't know if they do this free of charge, however.
I can't think of any hard drive manufacturer that would actually want to refurbish a returned hard drive when it would be far cheaper to just make a new one on an assembly line than take apart an old one to repair it. What they might want a dead hard drive for is failure analysis.
However - after Seagate's little dustup with the Apple OEM Firmware 7.01 drives, Seagate has instituted an OEM hard drive warranty program. They used to just make OEM hard drives the sole responsibility (without warranty) of the computer seller. Now they'll take back failed OEM drives during the warranty term for an exact replacement or credit towards new drive purposes.
http://www.seagate.com/www/en-us/support/warranty&_returns_assistance/oem_warrantystatements/
But if the old drive is completely inaccessible then your data are lost. The only chance you might have had would be to send the drive to a data recovery service. Such service is generally very expensive. However, you would have had to handle that on your own. Once you have Apple replace the drive they will keep the old drive and return it to the manufacturer.
I noted that this would not be unique to Apple. Their warranty and AppleCare terms recommend backing up all data before sending any equipment for repair.
You will need to talk with the store manager to see what they can do to help you. You can qalso call AppleCare and talk with a service representative. And, yes, they have every right to keep the old drive. Perhaps you should have told them you had data you needed to recover before you left the computer for the service. The door swings both ways, you know. But I think if you talk with the store manager about the situation they may be able to work something out to help you, especially if you ask nicely.
I'm guessing that by now they have no idea where that drive would be. It's probably in a pile awaiting return to the drive manufacturer.

Broadband speed dropped from 2 meg to less than di...

Hi everyone this is my first post, I am looking for some help / advice with an ongoing speed issue I have just joined BT broadband, my equipment setup is a D-Link 320 modem set in bridge mode to a cisco/Linksys E4200 router as they suit my need I only use the internet for surfing maybe the odd song / app from itunes plus online gaming through XBox live, when I first set everything up on 1/7/2011 I was getting a healthy 2,5 meg the max that my line is capable of getting, I did a another BT speed test on 3/7/2011 results below as you can see things have gone very wrong and I am getting less than dial up speed very frustrating.
Download speedachieved during the test was - 420 Kbps
For your connection, the acceptable range of speeds is 50-500 Kbps.
Additional Information:
Your DSL Connection Rate :608 Kbps(DOWN-STREAM), 448 Kbps(UP-STREAM)
IP Profile for your line is - 500 Kbps
9/7/2011 I did another speed test today at 13:00 hour results below
Download speedachieved during the test was - 410 Kbps
For your connection, the acceptable range of speeds is 50-500 Kbps.
Additional Information:
Your DSL Connection Rate :608 Kbps(DOWN-STREAM), 448 Kbps(UP-STREAM)
IP Profile for your line is - 500 Kbps
It has been 9 days now my equipment has been left on 24/7 but as you can see nothing has changed I know about the 10 day training period for things to settle down etc but surely I should have seen some improved by now i.e. my ip profile increasing a little
As I pulled 2,5 meg when I first set everything up does that mean my line is ok and should of stabilised by now or has my line been capped for some unknown reason
any help or advice is appreciated
many thanks
Solved!
Go to Solution.

hi yea Iv just a quiet line test and everything seems fine no noise.
I forgot to explain my equipment is connected upstairs using an ADSL approved extension cable that I bought from the BT shop as well as an I,plate, but I had the same issue with my last provider and I connected direct to the BT socket downstairs and I have been having the same issue this is why I changed to BT. Hear are the router states from last provider these were taken on 17/6/2011
ADSLValues
DescriptionThomson Livebox 2 Mini uk v7.1-h323
ManufacturerThomson
SerialNumber0812GH0WD3678CP
HardwareVersionT-E.1.0
SoftwareVersion6.3.9.6
DestinationAddressPVC: 0/38
ModulationTypeADSL_G.dmt
ATMEncapsulationVCMUX
ModemFirmwareVersionbcm96358_ADSL_PHY_A2pBT009c1.d17d
StatusUp
LinkStatusUp
LinkType PPPoA
DataPathInterleave
UpstreamAttenuation275
DownstreamAttenuation500
UpstreamNoiseMargin190
DownstreamNoiseMargin79
UpstreamMaxRate1040000
DownstreamMaxRate736
UpstreamCurrRate448
DownstreamCurrRate608
UpstreamPower121
DownstreamPower148
UpTime902134
Stats.Total.Values
LinkRetrain3
FECErrors187816
ATUCFECErrors0
HECErrors61
ATUCHECErrors0
CRCErrors163
ATUCCRCErrors0

Compatibility problem between HBS-730 and iOS6 (6.0.1) ?

I bought bluetooth headset named HBS-730.
But, I think iOS have some problem with the compatibility about Bluetooth as follows.
Sound streaming is delayed about 1 seconds. For instances, I got the game item in game play. After 1 seconds, The sound play. This is very unconfortable.
Also If I listen to the music and pause the play, I hear the noisy after 1 seconds.
I've search the similar issue in this community. and I found the follows.
https://discussions.apple.com/thread/4389635
Re: IOS 6 bluetooth issues - micro cuts on musichttps://discussions.apple.com/message/19670046#19670046
I think this is bluetooth 3.0 compatibility problem because backbeat headset is works well with iOS6.01
backbact is equiped with bluetooth 2.1
First of all, I wonder this issue is iOS's problem or headset's problem.
Please help me. I want to escape the this delaying problem.
I'm very unconfortable and I lost the trust about the Apple's product.
Thank you.

I bought bluetooth headset named HBS-730.
But, I think iOS have some problem with the compatibility about Bluetooth as follows.
Sound streaming is delayed about 1 seconds. For instances, I got the game item in game play. After 1 seconds, The sound play. This is very unconfortable.
Also If I listen to the music and pause the play, I hear the noisy after 1 seconds.
I've search the similar issue in this community. and I found the follows.
https://discussions.apple.com/thread/4389635
Re: IOS 6 bluetooth issues - micro cuts on musichttps://discussions.apple.com/message/19670046#19670046
I think this is bluetooth 3.0 compatibility problem because backbeat headset is works well with iOS6.01
backbact is equiped with bluetooth 2.1
First of all, I wonder this issue is iOS's problem or headset's problem.
Please help me. I want to escape the this delaying problem.
I'm very unconfortable and I lost the trust about the Apple's product.
Thank you.

Equipment master record updation in Asset master record

Dear Friends,
I have a query with regard to Equipment master record updation in asset master record. Here we have created equipment in Plant maintenance module and we have created asset in AS01 tcode. When we give the asset number to PM module guys, they can easily update the asset number in their equipment master by changing the equipment master record.
But when we enter the same in asset master record in 3rd tab allocations tab, initially it is accepting the equipment details like equipment number, category, object and tech description, but the same is not available after saving.
Please let me know whether I have to do any customization in asset settings inorder to get the equipment number populated in asset master record.
Thanks,
Dwarak.

Hi,
Thanks a lot for your reply.
I did both these customization, but still it is not working. Any other customization to be done? Please let me know.
And also in asset master record in allocations tab, do we need to select sync and workflow checkbox?
Thanks
Dwarak.

Follow up action 14 Inspection Type- Equipment status change

could anyone tell me which follow up action for 14 inspection type is to be bought into for changing Equipment Availablity status to Non Availability status when I reject calibration lot for that particular equipment.

hi
kindly check whether this FM will work for you QFOA_OBJECT_STATUS_SET
regards
thyagarajan

Equipment mailbox not showing partial days on calendar for certain user (in month view).

We have one user that is having a problem with viewing Equipment Mailboxes.
We are running Exchange 2010 version 14.02.0328.009. Client machine is running Outlook 2010 x86.
The mailbox is a check-out vehicle that he and one other person manage. When someone sends a request to the van, it books it for that time, then doesn't allow others to book it for that same time as expected. However, some users don't like to do their own
booking so they have him do it for them. Several times now he has went out on the calendar (actually 3 different vans, all respond the same way) and booked a van on a day that looked available to him, only to find out on that day that two different people
show up expecting that same van. One person booked it on their own, and he booked it again. It never gave a prompt to disallow him or tell him it was taken from the attendant. However, for the other guy that manages the mailboxes it looks just fine, for me,
for many other users I've compared with, it looks and responds as it should.
I have checked the settings on the equipment mailboxes as well as compared his Exchange account with the other person who is working as expected, they are identical. The thing that I've found is that if someone books a van for an 'all day' event, he sees
it just fine. If they set it up for a partial day, it never shows to him in month view.
Looking at the calendar permissions for the mailbox both of the people have equal rights. I tried setting this person to owner to see if it helped, to no avail. I also tried setting the "Show As:" to free, busy, tentative, out of office, all respond
the same way.
It seems to show up when he does a schedule view, but from a month view, nothing shows and it allows him to book the van. For everyone else that I've tested, it responds as expected.
I have deleted and recreated his profile on his local machine, and he even recently got a whole new desktop so it shouldn't be anything local (has been going on for many weeks), but I honestly have no idea why it's doing it. Any suggestions from the gurus
on here would be appreciated. Thanks!

Hi,
Since the issue only happens when this specific user view the equipment mailbox's calendar in Outlook monthly view, please access this user's mailbox in OWA and view the equipment maibox's calendar and send test meeting requests to have a try.
If the issue also happens in OWA, please run the following cmdlet to check the equipment mailbox calendar configuration:
Get-CalendarProcessing equipmentmailbox | fl
Regards,
Winnie Liang
TechNet Community Support

Can No Longer Drag JPG files From Finder Directly Into .fla Stage?

For the past six months I have been following a manual process to convert JPG files (exported from InDesign) into SWF files for display advertising assets.
Using pre-built FLA files as templates (configured with clicktags):
Open FLA templates (3 separate files for 3 IAB ad sizes)
Drag JPG from Finder directly into stage of FLA file, aligned to
Publish to output folder for renaming
Today, for no apparent reason, I can no longer drag anything into the stage of any FLA file. Not just the pre-built templates. Nothing will drag & drop into an FLA stage.
What I have tried:
Restarted Mac
Reset Flash preferences
What I know I can still do:
Drag files from Finder into the Library, and drag into FLA stage from there
"File > Import to Stage..."
This works but because of my naming convention it prompts to import them all each time because Flash sees the sequence
This is not another step I am willing to contend with for my manual workflow
Me and my creative team need to process hundreds of assets like this each week, so I'm very anxious to discover why functionality that was working, suddenly stopped.
Running:
MacBookPro Retina OS X 10.8.5
Flash CS6 v. 12.0.2.529

just want to add my annoyance to the pile here. I can't see any logic behind removing the drag and drop function, especially when adding a new folder is now a multi-step process that is far from obvious. to start a new playlist with local folder content you now need to:enter settingsclick into advanced settings (basically all settings now seem to be "advanced"?)manually find and add the foldergo through the adventure of finding the files in your library.
-- because they may or may not be listed under "local files" - you won't know because Ctrl+F is also removed. so you have to remember/know what the album you added is called and search for that. if you have a mixed bag of file names from various albums, you're basically shafted; there's no way to find them all with a single search.then you can add them to playlisteta: but wait! there's more! if you have more than 15 files? you're **bleep** out of luck, because the search will only display the first 15 hits among your local files, and then show you spotify library tracks.I can't help but feel as though spotify is doing everything they can to stop us using spotify to listen to local files, as bugs that make it more or less impossible persist through multiple versions - and now features that seem to me to be basic functionality are being removed?mega minus points from someone who's been using spotify since 2008.

Synchronisation of assets and equipment

Hi All,
I'm busy trying to link our assets to our equipment. In SPRO, i am trying to add two more fields for synchronisation.
I went to SPRO> Financial Accounting> Asset Accounting> Master Data> Automatic Creation of equipment master records> Assign Master Data Fields of Assets and Equipment
I enter the two new fields, but when i save it, it gives me the error " Consistency check for TAAPM2 resulted in error"
I did this before and never got this error. I tried searching on this forum, but nothing for this error.
Any advice on what to do?
Kind Regards
Emanuel

Hi Emanual,
In u2018specify conditions for synchronize master datau2019
I entered Equipment category as M (Machines), Object type as 2113 (Vehicles)
In Edit Asset Master Records I selected u2018Direct Synchronization After savingu2019 for create equipment and change equipment.
In u2018Assign Data Fields of Assets and Equipmentsu2019 I did not do any changes
In u2018Develop Enhancement for field and class assignmentu2019 I did not do any changes.
Still it does not create any equipments when I'm creating assets.
Thank you,
Raneetha

I contrloling an RTX equiped stage in a non-queue mode, but I think lab view is adding on a queue about 3 high

Similar Messages

Maybe you are looking for