I have an ipod 5g and when i turn it on it stays on the apple screen and i have put it into recovery mode and restored it twice but i cant get it to work
i need my ipod but i have been up for hours looking up what to do and trying to fix it but i dont know waht to do it just gets stuck on the apple screen. PLEASE HELP!!!!
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar
Similar Messages
-
Please help!
Nobody here can help you. Discussing jailbreaking is a violation of the forum terms of service. Go to the website that told you how to jailbreak and get the information you need there.
-
iPad stops responding, showing the Apple logo only,i tried to place into recovery mode and attempted to restore again but after downloading the software, it brings error in downloading s/w message.can anyone help please.Thanks
http://support.apple.com/kb/TS3694#error14
These errors are typically resolved by performing one or more of the steps listed below:
Perform USB isolation troubleshooting, including trying a different USB port directly on the computer. See the advanced steps below for USB troubleshooting.
Put a USB 2.0 hub between the device and the computer.
Try a different USB 30-pin dock-connector cable.
Eliminate third-party security software conflicts.
There may be third-party software installed that modifies your default packet size in Windows by inserting one or more TcpWindowSize entries into your registry. Your default packet size being set incorrectly can cause this error. Contact the manufacturer of the software that installed the packet-size modification for assistance. Or, follow this article by Microsoft: How to reset Internet Protocol (TCP/IP) to reset the packet size back to the default for Windows.
Connect your computer directly to your Internet source, bypassing any routers, hubs, or switches. You may need to restart your computer and modem to get online.
Try to restore from another known-good computer and network. -
my computer refuses my new iphone 5 and has put it into recovery mode and itunes has crashed on my computer. Can i get it out of recovery mode without a computer
No, you can't.
-
i dont know how i typed in my pass code wrong and now my iPhone is disabled. It will not let me restore it because i do not have the newset version of iOS 7. Please helppp
I thought you could still restore using iTunes on your computer. iTunes would download iOS 7.0.4 (current version) then restore from there. Of course, this assumes you are using a reasonably current version of iTunes.
Anyway, if I'm wrong and you cannot restore, try recovery mode descrbied here. Note you may have to try to get into recovery mode more than once.
http://support.apple.com/kb/HT1808 -
my iphone 5 died and when i went to plug it in to charge the apple sign came up and it wont go away it has been stuck for 2 hours. i cant turn it off because my lockbutton is broke. what do i do?
Make an appointment at an Apple Store to have your device examined by a technician. Or contact Apple Support. Get your lock button fixed then you can restore your phone.
-
My iPhone 4s randomly went into recovery mode and iTunes can't get it to restore.
Last night my iPhone randomly went into recovery mode on me. Just before I went to sleep a bunch of static lines appeared across the screen. The screen went dark and a few seconds later the Apple logo appeared. A few seconds later is disappeared. A few seconds later it came back. So on and so forth. I thought I had turned it off and was going to deal with it in the morning, but when I woke up the iPhone still just had the Apple logo going on and off again.
I've tried everything today. All the different button hold methods out there. I've tried to sync it to iTunes but the same **** keeps happening over and over again.
A message pops up saying "iTunes has detected an iPhone in recovery mode. You must restore this iPhone before it can be used with iTunes." So I press OK. Then I press the "Restore iPhone..." button on iTunes. It asks me if I'm sure I want to "restore it to the factory settings" and I click "Restore and Update". It then says that its "extracting software", "preparing the iphone to restore", "waiting for the iphone", then "verifying iphone restore with Apple". As this is going on the "connect to iTunes" sign is shown on the screen of the iPhone. When the "waiting for the iPhone" part starts, my screen goes black, then the apple logo pops up. The "verifying iphone restore with apple" comes on the iTunes and the status bar appears underneath the Apple logo on my phone's screen. It sits there for a couple of seconds with no progress and then the screen goes black. Then iTunes has the same **** message saying "The iPhone 'iPhone' could not be resotred. An unknown error occured (9)."
I've gone through this process countless times in the past few hours and have done everything that apple support has told me. The windows system is fully updated. So is the iTunes. I've restarted the computer. I have no idea whats wrong and its making my blood boil.
A couple of notes about the phone:
It's over a year old. It's never had water damage. It was nearing the max capacity of its internal storage. This has never happened before. I keep it in an Otter Box. I had very little problems with the phone. Lately a couple of apps like snapchat and the barstool sports app were taking a little longer to open up or would randomly close out and sometimes my camera would take a while to get going. But this problem is just ridiculous and completely rendered the phone useless.Hello Sean,
It sounds like you are constantly needing to restore your phone because it keeps going into recovery mode. Usually putting a device into recovery mode and restoring it can help isolate an issue to your iPhone hardware if an issue persists afterwards. I would try manually putting it into recovery mode and restoring it 1 more time:
If you can't update or restore your iOS device
http://support.apple.com/kb/HT1808
If that does not resolve it the symptoms indicate to me that it is a hardware issue causing this to happen and would seek service for it:
iPhone Repair - Other Repairs
https://www.apple.com/support/iphone/repair/other/
Thank you for using Apple Support Communities.
All the best,
Sterling -
iPad has blank screen. Screen froze and went blank. Have not been able to get any response. Forced in to recovery mode, but restore fails with a 1600 unknown error. Has anyone had any success in reviving an ipad in this state?
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
Update and restore alert messages on iPhone, iPad, and iPod touch
http://www.buybuyla.com/tech/view/012953a0d412000e.shtml
iOS: Resolving update and restore alert messages
http://support.apple.com/kb/TS1275
iPad: Unable to update or restore
http://support.apple.com/kb/ht4097
Cheers, Tom
These errors typically occur when security software interferes with the restore and update process. Follow Troubleshooting security software issues to resolve this issue. In rare cases, these errors may be a hardware issue. If the errors persist on another computer, the device may need service.
Error 1604
This error is often related to USB timing. Try changing USB ports, using a different dock connector to USB cable, and other available USB troubleshooting steps (troubleshooting USB connections. If you are using a dock, bypass it and connect directly to the white Apple USB dock connector cable. If the issue persists on a known-good computer, the device may need service.
If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode, put it into Recovery Mode.
Restore and wait for the error.
When prompted, click OK.
Close and reopen iTunes while the device remains connected.
The device should now be recognized in Recovery Mode again.
Try to restore again.
If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection.
Error 1600, 1601, 1602
Follow the steps listed above for Error 1604. This error may also be resolved by disabling, deactivating, or uninstalling third-party security, antivirus, and firewall software. See steps in this article for details on troubleshooting security software.
Message was edited by: Texas Mac Man -
My iPhone 4s randomly went into recovery mode and I can't restore it with iTunes...what do I do?
Last night my iPhone randomly went into recovery mode on me. Just before I went to sleep a bunch of static lines appeared across the screen. The screen went dark and a few seconds later the Apple logo appeared. A few seconds later is disappeared. A few seconds later it came back. So on and so forth. I thought I had turned it off and was going to deal with it in the morning, but when I woke up the iPhone still just had the Apple logo going on and off again.
I've tried everything today. All the different button hold methods out there. I've tried to sync it to iTunes but the same **** keeps happening over and over again.
A message pops up saying "iTunes has detected an iPhone in recovery mode. You must restore this iPhone before it can be used with iTunes." So I press OK. Then I press the "Restore iPhone..." button on iTunes. It asks me if I'm sure I want to "restore it to the factory settings" and I click "Restore and Update". It then says that its "extracting software", "preparing the iphone to restore", "waiting for the iphone", then "verifying iphone restore with Apple". As this is going on the "connect to iTunes" sign is shown on the screen of the iPhone. When the "waiting for the iPhone" part starts, my screen goes black, then the apple logo pops up. The "verifying iphone restore with apple" comes on the iTunes and the status bar appears underneath the Apple logo on my phone's screen. It sits there for a couple of seconds with no progress and then the screen goes black. Then iTunes has the same **** message saying "The iPhone 'iPhone' could not be resotred. An unknown error occured (9)."
I've gone through this process countless times in the past few hours and have done everything that apple support has told me. The windows system is fully updated. So is the iTunes. I've restarted the computer. I have no idea whats wrong and its making my blood boil.
A couple of notes about the phone:
It's over a year old. It's never had water damage. It was nearing the max capacity of its internal storage. This has never happened before. I keep it in an Otter Box. I had very little problems with the phone. Lately a couple of apps like snapchat and the barstool sports app were taking a little longer to open up or would randomly close out and sometimes my camera would take a while to get going. But this problem is just ridiculous and completely rendered the phone useless.Hello Sean,
It sounds like you are constantly needing to restore your phone because it keeps going into recovery mode. Usually putting a device into recovery mode and restoring it can help isolate an issue to your iPhone hardware if an issue persists afterwards. I would try manually putting it into recovery mode and restoring it 1 more time:
If you can't update or restore your iOS device
http://support.apple.com/kb/HT1808
If that does not resolve it the symptoms indicate to me that it is a hardware issue causing this to happen and would seek service for it:
iPhone Repair - Other Repairs
https://www.apple.com/support/iphone/repair/other/
Thank you for using Apple Support Communities.
All the best,
Sterling -
I have an iphone 3G which has been disabled after a child tried to get into it. Itunes will not connect until I have put the passcode in but the device will only enable emergency calls and does not allow a passcode to be put in. I have put it into recovery mode and itunes can't see it. There is currently no SIM card in it and it's not connectng to the wifi so I can't wipe it from the cloud. Any ideas how I can get into it?
iPhones require a SIM for activation.
Put the device in DFU mode (google it) and restore via iTunes. -
My ipod touch 4 put itself into recovery mode
My ipod touch 4 put itself into recovery mode and when i plugged it in it asked me restore it, i clicked restore and it extracted the software then crashed, leaving it with no software. i then gave it to my nearest apple store and the guy said it cant be fixed telling me it was a hardware problem. Any suggestions as to what it could be and if it can be fixed? I really appreciate it
What crashed?
iTunes? The whole computer?
What do you mean by crashed? -
I used to have Emoji on my iPod when I first bought it. I had to restore my iPod because it went into recovery mode and it deleted everything. How do I get Emoji back? Do I have to buy it off iTunes?
You can redownload iTunes purchases at no additional cost by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store -
i was in the process of jailbreaking and updating my ipod and when i was updating it,it went into recovery mode and now i cant get it out of recovery mode so what can i do??
Go elsewhere:
Jailbreaking voids the Apple warranty and also means that you will not get any support from Apple, including from this Apple forum. Jailbreaking can't be discussed in this Apple forum.
Unauthorized modification of iOS has been a major source of instability, disruption of services, and other issues -
Ipod touch wont load past apple screen. I have tried resetting by holding home button and on/off but after it resets it still only loads to the apple screen. When I plug the device in It stays on the apple screen and itunes does not recognize it? I fear it may be stuck in some sort of reset loop which is stopping itunes from recognizing it. How do I go about the process of sending it in to apple if I cannot find a fix? Thank you in advance, it is greatly appreciated!!
- See if placing the iPod in Recovery mode will allow a restore.
- If not successful and you can't turn the iPod fully off (that is required to place in recovery mode), then let the battery fully drain. After charging for at least an hour try the reset, restore again
- Then time for an appointment at the Genius Bar of an Apples store. -
Well my ipod 4th gen was updated it shut off and now when i try to turn it on it stays on the apple logo for abit then gets stuck on a white screen od blue or mixed colores i really need help fixing this plzz help
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar
Maybe you are looking for
-
i cannot seem to find where the original file for tracks that have been imported from a cd are kept because they are not in the itunes folder, however the song is somewhere as it does show up on spotlight search and plays when i click it. where would
-
How to validate a Particular Directory or file path in Presentation server.
Hi SAP gurus, I am having a requirement where I want to download a file into the Presentation server. The file path to download will be provided in a parameter. What I want to do is to throw a message to the user if He/She provides a wrong Directory
-
How can i refelect the Number of deliverable in Primavera
Hi all I am preparing an engineering Schedule. in which suppose any activty such Detail drawing of Compressor will contain 20 A1 size drawing. How can i refelect this in schedule. ACTIVITY Duration Resource No Of deliverable Start Finish Detail ... 6
-
I abandonned Aperture with rev1 and now that iphoto claims to open Aperture libraries went to see my long lost library on a whim and apple says I must upgrade to version 3 of Aperture to convert the library so iPhot can open it. I don't want to. the
-
Design View to use CSS included in header
In all views except the "Design" view, when you look at a page anything that's included in a CSS file imported from the assets/ folder will show HTML styled with the CSS. However, in the Design view it doesn't use that linked CSS file. Any hand-coded