I hhave a problem with my Sony Smartwatch MN2

I have problem with my Smartwatch. When I turn the watch on Is the clock in blue contrast,the menu is in blue contrast ,the whole watch has a blue contrast .Like on the photo. The sign Sony when i turn it on is also in blue contrast. Could please somebody help me. What is wrong with my watch?

I recommend that you try to update the software in your SmartWatch with the program Update Service:
http://www.sonymobile.com/global-en/tools/update-service/
If the problem still persists I suggest that you have your watch examined by a service center. Please contact your local support for more information:
http://www.sonymobile.com/global-en/support/contact-us/
What are your thoughts about this forum? Let us know by doing this short survey.

Similar Messages

New problem with my Sony xperia t2 ultra dual

I have recently discovered this new problem with my Sony xperia t2 ultra dual.it displays" sorry but xperia home is not wotking". And if iclick on OK it displays the same message again.
Can anyone help me solve this problem?
Please reply quickly what to do?

Repair the phone with PCC PC Companion (PCC) Bridge (for Mac) Alternatives on How to backup Xperias http://talk.sonymobile.com/thread/36355

VHS to DV tapes...problem with new Sony camcorders

I had a nice Sony miniDV camcorder, the DCR HC 30. Worked great to record almost all of my VHS tapes to DV, which I am using to created my iMovies. The camcorder worked fine in this mode. It then had a problem with regular recording, capturing the audio, but not video. Known problem to Sony, who repaired the camcorder at no cost. It worked great again, but the last time I went to record from my VHS tape, it worked for an hour, and then the touch-screen menu failed to respond to touch. (Another story).
I also have a newer Sony camcorder, the DCR HC 26. Connected it to the VCR to record from the VHS tape. I then discovered that this camcorder will allow recording FROM the camcorder TO the VCR with the AV connector, but if I want to record FROM the VCR, it will only work using the DV connector into an iLink port (Firewire).
I went to the 'Sony Style' store (yes,Palo Alto has everything!) and the guy first insisted it could be done with the new HC 38 and 48, but after he actually read the manuals, it was the same as the HC26: must have a Firewire port on the VCR. How dumb is that? How many of us have all these old VHS tapes, probably old VCRs too, and none of the old ones will have FireWire ports!
I have always recommended copying VHS footage to DV tapes, and now I am not going to be able to do that unless I get a converter. Seems a bit expensive for just the few VHS tapes that I forgot to convert previously.
I tried to see if the HC 30 can be repaired again....Sony wants $211 just to check it out. I can buy a new camcorder for $320 so it doesn't seem worth it unless I can connect the touch-screen failure with the problem with video recording that was supposedly corrected.
May have to get a converter.....last resort is another old camcorder Sony TRV something. It is on its last legs, but maybe it could work for a few hours more!
Wanted to let it be known that direct recording from an old VCR to new Sony miniDV cannot be done.

Hi tilman - yes - bottom line is not to discard an old vidcam with analogue-in when buying its 'higher-speced(?!) replacement - although that doesn't help Beverly with her problem.
There must be large numbers of second-hand cams with that function being sold as people rush to buy DVD vidcams etc, so it will be worth looking out for a good cheap one.
It seems that soon the only mini-DV cams will be higher-end models, some of which, being larger, have much reduced portability. Ah! Progress!

Problems with restarting Sony Experia Z2

I have had the Sony Experia Z2 for a couple months now. It's a good phone and all but it's a bit glitchy and can get very laggy for a few seconds. But other then that, it's a great mobile.
The one problem I have all the time is when I take pictures or have pictures in my gallery then delete them, I restart the phone and they all come back to my gallery?

You can perform a repair using PC companion:
http://www.sonymobile.com/gb/tools/pc-companion/
But you won't be able to backup apps with their data. I have heard helium app might work but not sure.
All we have to decide is what to do with the time that is given to us - J.R.R. Tolkien

I am having problems with the Sony XDCAM EX codec

I have been following this thread and updating the Adobe Application Manager had seemed to resolve my issue of Adobe asking me to register. Yesterday evening Adobe pushed out an update to some CS6 applications and I downloaded and installed them. This morning i find myself locked out of my projects in Sony XDCAM EX codec and says my trial has expired. I managed to re-activate by following instructions in #15. I am uncertain whether my problem was never really resolved or the update has caused this.
Plex

Premiere Pro...doesn't allow you to use the Sony XDCAM EX codec in trial mode.
It actually has since version 5.5.
Sometimes in CS6, the codec activation get's messed up and you have to redo it.
FAQ: Why are some codecs and sequence presets missing from my installation of Premiere Pro?

Overscan/Underscan problems with my Sony CRT TV

Hi there,
I want to use my Mac Mini as a mediastation and so I want to connect it to my TV for watching movies or to control my FrontRow.
I bougt me an DVI-Video-Adapter (the PAL-version because I'm in germany and its a PAL-TV).
But when I connct it there is a real thick border of black and unused space around my visible screen. Thats not so nice, because I dont want to waste space and it looks strange. When I activate "Overscan" in the "options" the picture ist zommed in an the whole TV-screen is used.... But it is zoomed more than needed and so the outer part oft the sceen isn't visible. I cant see the optionsbar on the top of the screen... Thats not so funny.
Can anyone help me or give me a tip how I can make the picture fit my screen?
BTW: I have an Sony KV-32CS71 32" Widescreen TV.
Thanks for your comments!

Hi, I've tested this SwitchResX... I have different results, but no working setup
I found out that I can create a 16:9-image using my MBP (native by OS X), nut my Mini gives me only 4:3-resolutions. I tried to copy the 16:9-settings (shown in SwitchResX) to the Mini (also using SwitchResX) but the eand was a extremely flickering or black screen.
BTW: When I typed in the settings copied from the MBP I got other frequencies in the Mini. I don't know why, but using exact the same settings was not possible for me.
Is the Intel-GMA inside the Mini that worse that it can't serve a TV-Set with such primitive resolutions?
As you can imagine it was also not possible to ret rid of those black frame.
I am beginning to dislike this GMA-Chip....

Right own a Sony KDLtelevision and sound system I have now installed iTunes match on my iPad and computer will I have a problem with the Sony television

I Have just installed I tune match on my computer and iPad but I have aSone KDL television and sound system have I got problem using iTunes match .

Hi,
Can you give us a bit more details?
Jim

Problem with "Best Quality" DVDs

I put together a few DVDs using iDVD 6. One was a little under an hour and encoded fine with the default "Best Performance." This one plays in all the DVD players in my house, no problem. Two others were a little over an hour and iDVD 6 said there was too much information and to switch to "Best Quality." I did so and created the DVDs. They play fine on my PowerBook and iMac, but do not play in any other DVD players (which are pretty new). They appear not to be recognized ("No Disc Inserted" or it keeps spinning).
Short of cutting out some content to make things fit with "Best Performance" (not really an option), does anyone know how to get around this problem?
TIA
PowerBook G4 Mac OS X (10.4.4)

Verbatim printable DVD-R
That's what I use and have very few problems with other people's players. Zero problems with my Sony players. Give it a try.
As far as burning speeds, the following includes info on how to do that by creating a disk image.
Suggest you create a disc image and then burn the DVD. File/Save As Disc Image...
http://docs.info.apple.com/article.html?artnum=164927
This will isolate any encoding/burning issues you may encounter. Once the disc image is created, double-click the .img and burn the virtual disc that should appear on your desktop, using Toast to burn the DVD. Disk Utility to burn the .img file. Usually, you can select a burning speed in Disk Utility.
There are variations to this process based on which OS X you are using...
Open Disk Utility (in Utilities folder in Applications folder), click on the virtual disc (maybe the .img) in the left-hand window. Click the Burn icon. A new window should drop down and your SuperDrive tray will open after clicking the Burn icon. Insert a recordable DVD. (Verbatim DVD-R preferred by me.) Click the Close button. Wait. Select a burn speed. Then click the Burn button.
-->If the virtual disk selection won't allow you to click the Burn icon, use the .img file instead. This may have changed in 10.3.9 and did change in Tiger.
Also, you can use DVD Player to play the virtual disk to check your iDVD project before burning to DVD. Launch DVD Player. File/Open VIDEO_TS (Open DVD Media... in Player 4.6). Find the VIDEO_TS folder and open that. (The audio folder is for DVD-Audio disks.)
http://docs.info.apple.com/article.html?artnum=93006

Smartwatch Mn2

Hello, i have two problems with my Xperia device. I use Android 4.4.4 (14.4.A.0.108)
I have a problem with Sony Smartwatch MN2 and connecting them to my phone.
My previous phone was different brand than Sony, and my Smartwatch worked very well with it.
Now, i set up my Smartwatch with my new Sony Xperia Z1 compact. But i have a problem. I connect them with my phone, but when i run app on smartwatch like missed calls, or messages, it loads normaly, but when i try to run weather, or smart camera, or any app like this, it takes veeery long time to load so my smartwatch turn off display or if i still touch it with my fingers, it loads after 20-30 seconds.
I know this is not normal, i still use stamina mode and other baterry saving features from Sony, but i also tried to turn them all off, restart phone, but smartwatch dont still work as they should. I use also sony phone, and there is a big problem with it. Can you advise me something?

Contact your local Xperia care
http://www.sonymobile.com/global-en/support/contact-us/
"I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

Smartwatch 2 problem with button

I have for a few weeks the SW 2. It works good but..
I have to press so hard on the (only) button for starting the 'android-like" interface.
Sometimes I have to press 5 times for 1 succesfull hit.
You have to press 2 times to reach the menu...
It goes better when i have the watch in my hand and i can press with my thumb.
But with the watch around my wrist it is not easy.
Are there any persons with the same problem ?
My forefinger already hurts.
Isn't it posseble to go to the menu with double-click somthing like that ?

I see it was reported on here also http://talk.sonymobile.com/t5/Wireless-accessories/Sony-SmartWatch-2-screen-detaching-after-2-days/m...
For a successful technology, reality must take precedence over public relations, for Nature cannot be fooled. Richard P. Feynman

Problems with HDV footage from sony HDR - HC9

I have a new sony HDR-HC9 cam corder. I want to shoot in hi def (HDV) format for best quality, but I produce standard def DVDs as a finished product. I was hoping to use the built in iLink conversion from HDV to DV when downloading to the computer into iMovie. I have had many problems with this.
Usually, when I set it up to do the downconversion, I see a blue screen in iMovie, although iMovie will ff and rew the camera, no images come across. I experimented with setting the camera in DV record mode at the same time as I had the iLink down conversion set, and this appeared to work. I started downloading an hour tape, and when I came back 65minutes later (after it should have been done), saw the message that iMovie had quit. Reopened the project, and saw an hour worth of footage in the trash, but it was too crazy to reorder the clips from the trash back to the clips pane.
I resigned to import in hdv (1080i) format and not mess with hardware downconversion. This worked fine. I then added some chapter markers and shared the project with iDVD. I saved the project as an image file and then mounted it to check it for errors. The video was OK, but towards the end of the project, the sound was out of sync by a few seconds with the video.
I deleted encoded assets from the iDVD project, then reburned (save as image file). Same defect.
I then started a new iMovie project in standard DV widescreen, and dragged all of the clips from the HDV (1080i) project into the time line. It took over an hour for my mac mini to run the conversion, but the movie in iMovie appeared OK. I redid the iDVD project, and saved as image file. It appears to have worked correctly (although I have not looked at it on my widescreen TV yet to assess image quality.
Questions:
1) Has anyone had any luck getting HDR-HC9 iLink HDV-DV hardware conversion to work with iMovie, consistently?
2) Can anyone comment on image quality issues with converting HDV to DV footage using iMovie software.
3) Has anyone seen audio sync problems with iDVD from HDV original footage.
Thanks

Hi - you may get a more exact answer in the BlackMagic Macintosh forum, since there aren't a lot of BlackMagic queries on the Apple Discussions forums:
http://forum.blackmagicdesign.com/viewforum.php?f=11

Problems with Sony NX3 AND Sony Z5 avi files

Very, very strange problem. I will try to give as much detail as possible so bear with me.
I currently edit with two different computers. One uses Premier 3 the other uses Premiere 6. I shoot with several different cameras, but for purposes of this discussion I will talk only about the Sony Z5 and the Sony NX3. I capture my footage on a CF card (Z5) or SD card (NX3)
All HD footage shoot with the Z5 and/or the NX 3 works fine on either system. However any SD footage that is over a certain length will not import into premiere 6 (if it's from the Z5) or the length of the footage will only be 2:37 (on footage from the NX3). However the SD footage from either camera will play perfectly on the system with Premiere 3.
Any ideas on what my problem with premiere 6 is?

I caputured footage from my ZU1 yesterday that encountered time code breaks. They should not have been there. My only thought is that the breaks occured when I shut the camera down and started recording later.
Maybe... I assumed it was user error... I was wondering if perhaps a setting in the camera was causing the breaks when the camera powers down.

Problems with getting my Ipod Touch to work on my Sony Bravia or any TV

I am having problems with getting videos or movies to play on my Sony Bravia HDTV or any TV. I have a first generation Ipod Touch and I have the Apple AV Composite Cables and all I get is sound for both TV's that I tried. I read one post where some guy had a faulty Ipod that wouldn't work. Does anyone know how of something hidden or special that needs to be done or how did they fix the problem if they had the same one? Thank, ejcarlson

Check connection, if you have a case on your Ipod the connection may not be good enough.

Capturing Problem with Sony TRV330

Capturing problem with Sony digital8 trv330.
I recently purchased the above camcorder from eBay for capturing old 8mm/Hi8 tapes for editing purpose. The camcorder set to A/V -> DV OUT connected with Firewire to my Power G4 and the Easy Setup was DV-NTSC. The playback on the capture window looks OK except there were no timecode in the Timecode Duration Field and the Current Timecode Field (both shown 00:00:00:00) during playback but there was timedoce in the camcorder viewfinder. When I click the Capture Now button, the capturing window show up with message “waiting for timecode ….”. I have to click “esc” to stop the capturing operation. I trash the Preferences and Ran the Disk Utility without success. I also tried the Easy Setup with DV-NTSC DV Converter as well as DV-NTSC 32Khz, nothing work.
My set up is: Mac Power G4 version 10.5.5/ F.C.E. 4.0.1/ QT7.5.5/ Startup 160 GB-89 GB available/ Scratch 350GB-277GB available. Folks, I need help. Thanks everybody.

Hi, I have a similar problem. I am trying to digitize my 8mm tapes (via firewire) using final cut express (4.0.1). Using easy setup I use DV-NTSC DV Converter and do capture now. I transfer the entire tape but notice the audio is out of synch with the video. This problem gets worse throughout the transfer process. When I use the esc to complete the transfer I get the error " The audio sample rate of one or more of your captured media files does not match the sample rate on your source tape....." So after searching around it is recommended I change the audio sample rate to 32 kHz option. However, when I do this using easy setup and picking DV-NTSC 32kHz I cannot use capture now because I have no timecode and so the window comes up with the message "waiting for timecode". Since there is no timecode this option does not work. Any suggestions? Thanks, Dan

When downloading from a Sony minidisc video camera, the picture is downloading but without sound. Previously, it had downloaded successfully both sound and picture. I have subsequently upgraded to Lion X (10.7.4). Is there some problem with the driver?

When downloading from a Sony minidisc video camera, the picture is downloading but without sound. Previously, it had downloaded successfully both sound and picture. I have subsequently upgraded to Lion X (10.7.4). Is there some problem with the upgrade which is affecting the transfer? Is there a way of resolving this?

When you have kernel panics, the pertinent information is in the panic report.
These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
In the Console window, select
DIAGNOSTIC AND USAGE INFORMATION ▹ System Diagnostic Reports
(not Diagnostic and Usage Messages) from the log list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar.
There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points down. You'll see a list of reports. A panic report has a name that begins with "Kernel" and ends in ".panic". Select the most recent one. The contents of the report will appear on the right. Use copy and paste to post the entire contents—the text, not a screenshot.
If you don't see any reports listed, but you know there was a panic, you may have chosen Diagnostic and Usage Messages from the log list. Choose DIAGNOSTIC AND USAGE INFORMATION instead.
In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
Please don’t post other kinds of diagnostic report.
I know the report is long, maybe several hundred lines. Please post all of it anyway.

I hhave a problem with my Sony Smartwatch MN2

Similar Messages

Maybe you are looking for