I pod touch makes a shutter sound and goes to the power off slider screen for no reason tried restoring several times and wonder if it is an internal error this ipod has no camera
my ipod touch makes a shutter sound ( no camera on this ipod ) and then goes to the power off slider screen. It will do this several times and then screen goes blank have restored several times with no change is it terminal or can it be repaired this was purchased as a refurb
If you press and hold the home button and click on the sleep button once, the iPod will make a screenshot of your home screen and add it to the photos on your device.
If you don't press the home button or the sleep button during to do this, one of your buttons might be stuck.
Try to reset the iPod by holding the sleep and home button for about 10sec, until the Apple logo comes back again, ignore the "slide to turn off" message when you press and hold the buttons.
If this does not work, wet it up as new device:
How to back up your data and set up as a new device
Similar Messages
-
My ipod keeps flashing on and off by itself and goes to the power off slide screen. How can I fix this problem?
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
On my Ipod touch the screen will not work. I can't slide it to unlock and when i hold down both buttons the red slide comes up and i can't slide that either or press the cancel button. I've powered it down several times and i've turned it back on and it still will not work. What do i do? Please help!!!
On my Ipod touch the screen will not work. I can't slide it to unlock
Try here > iPod touch: Troubleshooting touchscreen response -
help...my ipod keeps returning to the power off screen and keeps flickering?
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
I always make sure to take good care of my ipod, I have no warrnety, It has not been 3 years yer, never spilled anyhting on it nor did i drop/crack it. It happened randomly. Why would this happen...I have restored it tow times and yet happens, it flashes black and constanyl taking me to power off botton..
I'm really frustrated and can't afford another one..It was ios 4 something when i bought, bought it in 2010 marchTry:
- iOS: Not responding or does not turn on
- If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order. -
version 6.1.6(10B500); model#MC547LL/A; 60GB (40 used/20 avail)
IpodT auto redirects to the power off (slide) option while in use. Then while not using it, it will not power off to conserve the battery. I have to enable the assistive touch to save battery life. Software states up to date with iOS 6.1.6. PLEASE HELP!Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar -
Hi, im having problems with my iphone it would always be showing up "No Service" even when I get my simcard out, when i turn airplane mode it would switch to " Searching" and then go back to "No Service", i have tried restoring several times, but nothing has changed. I must say that my iphone was working perfectly until the last months my battery began to die all from a sudden, so my phone got turn off really frequently, so then i ordered a battery and changed it myself so when phone was on.. it had this problem.. im desperate here
No I haven´t take it to Apple Store, i think I will actually. My iphone was jailbroken and ulocked with gevey sim, but when this failures began i decided to restore it, and I did preserve the baseband, but when I took it into one of these "Places" they told me it would be a good idea to do a clean restore and see if this fixed the problem so I upgraded my baseband, and right now my iphone is freshly restore, no jailbreak no nothing.
Btw yes something like a year ago my screen was replaces by others not by apple, but I didnt had any issues after this.. until today (a little more than a year later). -
HT1430 I held the sleep/wake button for a full minute, and only the Power Off slide appeared.
I cannot access the power off slide because there is a pop-up message saying "Cannot connect to iTunes store" to which I cannot select the OK button. How else can I power off the iPad2?
Try a reset: Simultaneously hold down the Home and the On button until the iPad shuts down. If the Off slider appears, ignore it. This should take about ten seconds, give or take. Once the shut down completes, use the On button to restart.
-
I applied the update today to an Iphone 5 and it totally trashed the phone. Total restore WOULD NOT bring it back- it is a nice paper weight- Error 6. Any body got a clue? Have tried restore several times- yes- disconnected all usb devices THX
Did you try all 7 trouble shooting steps outlined Apple Support Page you linked from?
-
Respected sir,
i have ipad-2 -16gb wifi. i recently upgraded to latest software 4.3.5 by using i tunes. after updating my ipad wifi icon is bleached and showing no wifi tried resetting several times and also tried rebooting it and i restored the software several times but still the problem remains please help me out.
waiting for your response.
i am using windows 7 operating system.
with regards
vinayakaVinayaka-
After all you've tried, Dah*veed is probably right about needing warranty assistance.
But first check to be sure Settings-Airplane Mode is set to OFF, and Settings-WiFi-WiFi is set to ON.
Try unplugging your WiFi router for a few seconds. Then reset the iPad's network. Go to Settings-General-Reset-Reset Network Settings. You will need to reconnect to your WiFi.
Fred -
I've uninstalled and reinstalled iTunes several times and each time it says to re-install iTunes but it doesn't solve the problem. I've been trying to get this to work all day and I'm extremely frustrated. Someone please help me with this. I've done all the reserach on how to fix this and nothing has worked. I just get the same message over and over again.
When I go do download iTunes I get a screen that says, "The feature you are tyring to use is on a network resource that is unavailable." Then is says "Click OK to try again, or enter an alternate path to a folder containing the installation package iTunes64.msi in the box below". I click "OK" and it says that the path cannot be found. Don't know what do to here.
Sounds like at least two different things are happening to you at once here.
Steps for dealing with the "network resource" message, follow:
(1) Download the Windows Installer CleanUp utility installer file (msicuu2.exe) from the following Major Geeks page (use one of the links under the "DOWNLOAD LOCATIONS" thingy on the Major Geeks page):
http://majorgeeks.com/download.php?det=4459
(2) Doubleclick the msicuu2.exe file and follow the prompts to install the Windows Installer CleanUp utility. (If you're on a Windows Vista or Windows 7 system and you get a Code 800A0046 error message when doubleclicking the msicuu2.exe file, try instead right-clicking on the msicuu2.exe file and selecting "Run as administrator".)
(3) In your Start menu click All Programs and then click Windows Install Clean Up. The Windows Installer CleanUp utility window appears, listing software that is currently installed on your computer.
(4) In the list of programs that appears in CleanUp, select any iTunes entries and click "Remove", as per the following screenshot:
(5) Quit out of CleanUp, restart the PC and try another iTunes install. Does it go through properly this time? -
Unable to sync iphone4. iphone not recognized. wants me to restore factory settings. I've done that several times and problem persists.This has been an issue sunce buying the phone.
Hello @dazegoneby,
I understand that your HP Pavilion p6-2220t Desktop PC running Windows 7 used to connect to your home network without an issue, but recently it does not recognise the network. I am providing you with an HP Support document: Troubleshooting Your Wireless Network and Internet Connection (Windows 7), which has steps to help resolve issues such as this. Now I am not recommending that you do the step that asks you to reset up your router as you have other devices that are working fine so that would not be the issue.
If the above document does not resolve your issue could you please re-post with either a screen shot of your Device Manager showing what is listed in Network Adapters or re-post with which wireless card you have.
Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter -
My new IPAD 2.0 keeps freezing on the current application. When I hit the button on the IPAD it does not go back to the icon "desktop"....I have restarted several times and reset my settings and it is still happening. HELP.
You'll have more success getting an answer to your questions, if you post them in the appropriate discussion board....
https://discussions.apple.com/community/ipod/ipod_touch -
I have tried making a new playlist, and have synced it a gazillion times. This all happened when I bought a new computer and transferred my Ipod to it...with upgraded Itunes software. I have tried everything.
Thanks -- actually I worded the question wrong. I was trying to find my songs icon and kept reloading Itunes to try to find it. All I could get was the store. I finally figured out how to reset the desktop and I got my icon back. Thanks for your answer.
-
I would appreciate any suggestions to solve this problem
Also I've tried to reset it and it still keeps doing the same thing
Maybe you are looking for
-
The format: JFrame that contains 2 JPanels that I want to switch depending on user input. I've tried from with the JFrame code: JPanel jpanel1 = new JPanel(); The constructor in JPanel1 creates an instance of jPanel2 & jPanel3. jPanel1.jPanel2.setVis
-
I have connected Oracle 9i and DB2 v7 and query DB2 in SQL Plus is fine. However, it doesn't for the connection between OWB and DB2. Anyone can help? Thanks!
-
What are the main differences between 9 iAS and Oracle 8.1.7 ?
My question is focus on JServ/JVM/EJB Deployment. 1. They both provide Appach JServ to support JSP/Servlet application 2. They both provide JVM 8i to support EJB 1.1. 3. You can deploy JSP/Servlet application to JVM via mod_ose. 4. On the White paper
-
I have rendered out 330 frames as png files into a sequence that can loop. I brought the group of files into PPCS4 as a sequence and copy/pasted it 3 times on my timeline. I rendered it out a couple time last night and this morning as a WMV just fine
-
Guys Deployment of the New GL at half the exercise, have prerequisites? Tks Regards Moderator: Please, search before posting