I want to install OS X 10.3 from an external drive

hi there
I had restored my OS X 10.3 on an external hardrive with fire wire from my girlfriend iBook .now i want to put the OS X 10.3 on my ibook because it had an older OS(9.2) so i conect the hard drive to my ibook and i went to the start dissk menu and i chosed to start from the hard disk so it restated and then appers to me the apple logo and thats it.....nothing more,i left it for more then half houre but nothing happend so is there anything that iam missing?....by the way i restoerd the OS X 10.3 through the disk ultiltiy aplecation
my iBook is a dual usb

tom:
This is a bit involved, so let me see if I have it right.
You have Panther installed on an external FW HDD from your girlfriend's iBook.
You want to install (copy/clone) Panther from the external FW HDD to your iBook, and are having problems.
Are there original Panther install disks somewhere? On which computer is it installed?
Unless you have a multi-user pack the software was installed under a single user license agreement which says, in part:This License allows you to install and use one copy of the Apple Software on a single computer at a time. This License does not allow the Apple Software to exist on more than one computer at a time...In other words, as long as the OS is running on one computer, it is illegal to install it on another.
Good luck.
cornelius
Message was edited by: cornelius

Similar Messages

Install Leopard and Snow Leopard from an external drive?

Hey guys,
I have a 120GB ext drive and was curious as to if its possible to install Leopard and Snow Leopard from it if I have the DMG's. I guess my main question is how would I setup formatting in Disk Utility?
Thanks!

Set up two 10GB partitions and a third partition for the rest of the drive on the external drive, use Disk Utility to "Restore" the mounted installer DVD to a 10GB partition on the drive.
Plug the drive into a Mac and hold the option key down during boot. Select the installer you wish to use.

[Guide] Install and run Windows 7/8 from an external drive without using bootcamp (works for late 2012 iMacs with 3TB drive)

This is a copy of a post from my blog, you can also Read it on my blog...
Introduction
After I received my new iMac with a 3 TB Fusion Drive, I was disappointed when I realized that Bootcamp was not running on this model and prevented me from installing Windows on it. I wanted to take advantage of the powerful iMac hardware to play games but I couldn't.
There are a few ways of working around this limitation, but I found most of them quite complex and most of the time they required formatting the internal hard drive or repartitioning it and go for a brand new installation of Mac OS X. I was not comfortable with that.
But there is another way, and that is to install Windows on an external hard drive, using either USB or Thunderbolt. Personally I used a Lacie Rugged 1 TB drive that has both USB3 and Thunderbolt connectors. Both work very well.
This guide may interest you if:
You have an internal hard drive of more than 2TB and you can't run bootcamp at all (like late 2012 iMacs with a 3TB drive)
You have limited space or you don't want to dedicate disk space on your internal hard disk drive to a Windows installation
What this guide will make you do:
It will make you erase all your data from your external USB3/Thunderbolt hard drive
It will make you install Windows on your external USB3/Thunderbolt hard drive
It will make you install bootcamp drivers
What this will not make you do:
It will not make you modify anything on your internal Mac hard drive
It will not make you use or install the bootcamp assistant
It will not activate the Preference Pane for the default boot drive. You have to boot by pressing the ALT key to manually select your boot drive each tome you want to boot Windows.
What you'll need
An external hard drive with a USB3 and/or Thunderbolt connector. This drive will be formatted so ensure you saved your files before going further. You can use either an SSD drive or a classic hard drive.
A Windows 7 or 8 install DVD or ISO (check whether to install 32 or 64 bits versions based on your Bootcamp drivers) and the corresponding Windows serial number.
One of the following:
Mac OS X with a Windows 7 or 8 Virtual Machine (use VMWare Fusion or Parallels Desktop for example. Note: VMWare Fusion seems to have some issues with Thunderbolt and USB3. Plug your drive to a USB2 enclosure or hub to work around this -it worked for me-, or use another VM software) → Read the important note below
A PC running Windows 7 or 8 → Read the important note below
Windows AIK (free) running on your Virtual Machine or on your PC, or just the imagex.exe file (the rest of the Windows AIK package is not needed)
Download imagex.exe
Download Windows AIK (this download and installation is not required if you have already downloaded imagex.exe)
Bootcamp drivers for your Mac. You can get these either by running bootcamp from your Mac (Applications > Utilities > Bootcamp) or, if like me you have a 3TB drive and can't run bootcamp at all, use the direct download links here.
A USB stick to store your bootcamp drivers
IMPORTANT: If your Mac has a 64 bits processor, your Windows Virtual Machine on OSX, your Windows installation on your PC and your Windows DVD/ISO must also be in 64 bits!
Step by Step guide
Step 1: Get the install.wim file
If you have a Windows ISO file:
Mount the ISO
If you're on OS X: double click on the ISO file
If you're on on Windows 7: Use a software like Virtual Clone Drive (free)
If you're on Windows 8: double click on the ISO file
Open the mounted drive, then go to the "sources" folder and locate the "install.wim" file. Save this file to C:\wim\ on your Windows installation or virtual machine.
If you have a Windows DVD: open the "sources" folder on the DVD and locate the "install.wim" file. Save this file to C:\wim\ on your Windows installation or virtual machine.
IMPORTANT: If instead of a "install.wim" file, you have "install.esd", you can not continue this step by step guide. And an ESD file can not be converted into a WIM file. So you must get a version of the Windows installation DVD/ISO that has an install.wim file.
Step 2: Clean, partition and format your external hard drive
On your Windows installation or virtual machine, plug in your external hard drive (can be plugged using USB2, USB3 or Thunderbolt at this stage)
Open the command prompt in administrator mode (cmd.exe). To run it in administrator mode, right click on cmd.exe > Run as admin.
Type the following and hit enter to open the disk partitioner utility:
diskpartType the following and hit enter to list your drives:
list disk
This will display a list of disks mounted on your computer or virtual machine. Make sure your drive is listed here before you continue.Identify the disk ID of your external hard drive. Replace # by your real external disk ID in the command below:
select disk #Clean all partitions by typing the following (warning: this will erase all data from your external drive!):
clean
Create the boot parition by typing the following followed by the enter key:
create partition primary size=350
This will create a 350MB partition on your external driveFormat the partition in FAT32 by typing the following:
format fs=fat32 quick
Set this partition to active by typing:
active
Assign a letter to mount this partition. We will use letter B in our example. If B is already used on your PC, replace B by any other available letter:
assign letter=b
Windows will detect a new drive and probably display a pop-up. Ignore that.Create the Windows installation partition using all the remaining space available on the external drive by typing the following:
create partition primary
Format the new partition in NTFS:
format fs=ntfs quick
Assign a letter to mount this partition. We will use letter O in our example. If O is already used on your PC, replace O by any other available letter:
assign letter=o
Windows will detect a new drive and probably display a pop-up. Ignore that.Exit the disk partitioner utility by typing:
exit
Step 3: Deploy the Windows installation image
Still using the command prompt in admin mode (you didn't close it, did you? ), locate the imagex.exe file mentioned in the "What you'll need" section and access its folder. In our example, we have put this file in C:\imagex\imagex.exe
Type the following and hit enter (remember to replace o: with the letter you have chosen in the previous step):
imagex.exe /apply C:\wim\install.wim 1 o:
This will take some time. The Windows installation image is being deployed to your external driveOnce done, type the following to create the boot section (remember to replace o: and b: with the letters you've chosen in the previous step):
o:\windows\system32\bcdboot o:\windows /f ALL /s b:
If you get an error message saying that you can't run this program on your PC, then most probably you are running on a 32 bits installation of windows and you're trying to deploy a 64 bits install. This means you did not read the important notes in the beginning of this guide
If you get an error message on the options that can be used with the BCDBOOT command, then it's because you're installing Windows 7, and the /f option is not supported. If that is the case, remove /f ALL from the command and retry.
Step 4: Boot from your external drive and install Windows
Plug in your external drive:
If you've done all the previous steps from a Windows PC, unplug your external drive from your PC and plug it to your Mac, either on a USB3 or a Thunderbolt port.
If you've done all the previous steps from your Mac using a Virtual Machine, ensure the external drive is plugged in to a USB3 or Thunderbolt port. Using USB2 should also work but you'll get very poor performance so I don't recommend doing that.
Reboot your Mac and once the bootup sound is over, immediately press the ALT (option) key and release it only when the boot drives selection screen appears. If you did not get the boot drives selection screen, reboot and try again. The timing to press the ALT (option) key is quite short. It must not be too early or too late.
On the boot selection screen, choose "Windows" using the arrow keys on your keyboard, then press enter.
The Windows installation starts. Follow the on-screen instructions as normal. The installation program will restart your computer one or 2 times. Don't forget to press ALT (option) right after the bootup sound, and boot on Windows again each time to continue the installation.
Step 5: Install bootcamp drivers
Once the Windows installation is complete, plug in the USB stick where you stored the bootcamp drivers (see "what you'll need" section), open it and right click on "setup.exe" and select "Run as admin". Follow the on-screen instructions.If you have an error saying that you can't run this program on this PC, obviously you have installed a 32 bits version of Windows and the bootcamp drivers for your Mac are made for a 64 bits version. You have to restart the whole guide and make sure to get a 64 bits version of Windows this time!
Once the bootcamp drivers are all installed, reboot and press ALT (option) after the bootup sound to boot on Windows again. And Voilà, you have Windows installed on your USB3/Thunderbolt drive running on your Mac.
Now each time you want to boot on Windows, press and hold the ALT (option) key after the startup sound and select "Windows", then press Enter.

Hi i'm trying to follow your guide, I installed windows 8 on bootcamp to do it planning to remove it after the operation is done, but i get stuck at part 3: every command i give to imagex i get a pop-up ftom windws asking how do I want to open this kind of file install.wim and imagex does nothing, what do i have to do to stop those pop-ups?

Easy way to install bootable OSX (or Win XP) on external drive in iMac?

HD in wife's 17" white iMac Core 2 went belly up. She exclusively uses Windows XP on the machine via Bootcamp.
Any want to do an install on 250G Western Digital USB HD so that she can run from that and just ignore the screwed up drive inside the iMac? If OSX than I'd want to install Bootcamp and Win XP on the external, too.
Or, if feasable, just install XP on the external HD and boot from there & again ignore the broken drive inside the iMac?
Thanks.

You should have no issues booting from a Mac OS X install DVD and installing Mac OS X on an external HDD, USB or FireWire. The issue is going to be getting Windows on that drive. Boot Camp will only install a Windows partition on a Mac's internal drive, but not an ext drive.
However, if anyone has figured out how to do this it would be the folks in the Boot Camp forums. The Forums are at the bottom of the main Apple Discussions page under Windows Compatible Technology. Here is a link;
Boot Camp: Installation and Storage
Dah•veed

I have backed up my disk using Time Machine. Now I want to delete the backed-up files from my hard drive. But when I do and reconnect the external hard drive, the files are also deleted on that. What do I do?

I have backed up my disk using Time Machine. I then deleted the back-up files from my MacBook hard drive.
I then reconnected my external hard drive and find the files I deleted from my hard drive are also deleted from
my external hard drive. Can someone tell my what what happened? I'm confused.

Hello,
Time Machine is not a good way to do that, when it eventually needs more room it deletes old Backups to make room.
If you really want to keep Files but remove them from the Internal Drive, then I'd get another external drive to copy or clone them to that is not used for TM.

HT201250 how do I disable time machine? I want to use my external drive as additional storage. But it mirrors everything I edit. If I remove a document, it removes it from the external drive as well.

how do I disable time machine? I want to use my external drive as additional storage. But it mirrors everything I edit. If I remove a document, it removes it from the external drive as well.
I purchased a 1 TB WD passport drive, formatted for Mac. I set it up originally (mistakenly) to backup time machine. I went back and set it to "do not backup" It still backs up evey document I edit. If I add a document when the drive is disconnected, it automatically adds it to the external drive the next time connect to the passport drive. If I remove a document the same thing happens.
I need additional storage to free up space on my laptop hard drive. This is not working the way I want it to. Help!

Do not backup your startup volume to another partition on the same drive. If the drive fails you have nothing. Always backup to another drive or volume on another drive.
The I/O error usually means there's a problem with the drive. Clone ASAP, then repartition and reformat the main drive. Then restore the clone. Here's the basic process:
You will have to backup your OS X partition to an external drive, boot from the external drive, use Disk Utility to repartition and reformat your hard drive back to a single volume, then restore your backup to the internal hard drive.
Get an empty external hard drive and clone your internal drive to the external one.
Boot from the external hard drive.
Erase the internal hard drive.
Restore the external clone to the internal hard drive.
Clone the internal drive to the external drive
Open Disk Utility from the Utilities folder.
Select the destination volume from the left side list.
Click on the Restore tab in the DU main window.
Check the box labeled Erase destination.
Select the destination volume from the left side list and drag it to the Destination entry field.
Select the source volume from the left side list and drag it to the Source entry field.
Double-check you got it right, then click on the Restore button.
Destination means the external backup drive. Source means the internal startup drive.
Restart the computer and after the chime press and hold down the OPTION key until the boot manager appears. Select the icon for the external drive and click on the downward pointing arrow button.
After startup do the following:
Erase internal hard drive
Open Disk Utility in your Utilities folder.
After DU loads select your internal hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID then click on the OK button. Click on the Partition button and wait until the process has completed. Do not quit Disk Utility.
Restore the clone to the internal hard drive
Select the destination volume from the left side list.
Click on the Restore tab in the DU main window.
Check the box labeled Erase destination.
Select the destination volume from the left side list and drag it to the Destination entry field.
Select the source volume from the left side list and drag it to the Source entry field.
Double-check you got it right, then click on the Restore button.
Destination means the internal hard drive. Source means the external startup drive.
Note that the Source and Destination drives are swapped for this last procedure.

Running SL from an external drive on Lion-installed iMac

I recently installed Lion on my iMac with the intention of having Snow Leopard bootable from an external drive when I need to run all my PPC apps etc. Having formatted an external drive, I put in the Mac OSX SL DVD into the Mac to install it on to the external drive, but before I could do this, a message appears:
" You can't use this version of the application Install Mac OS X with this version of Mac OS X.
You have install (sic) Mac OSX 23.1"
Can anyone interpret this message for me please?
Thanks

The SL DVD. If you actually tried it, you'd have found that the blank drive doesn't appear because it doesn't yet contain Mac OS X.
(59758)

HT1338 If I have OS 7.5 installed on an external drive, can I start up from the external drive in that OS when my macbook pro is 10.7?

If I have OS 10.6 installed on an external drive, can I start up from the external drive if I have 10.7 installed on my macbook pro?

Provided that the MBP supports booting from that version of 10.6, and the install was from a retail disk (not a different Mac model), then yes. If it's a newer Pro that came with Lion, it may not boot to 10.6.
Matt

Currently my internal drive is full due to Aperture. I want to work with Aperture from a external drive verses my internal drive. In addition, I want to back-up my work to another external drive. Is this easily done? Does this make sense? Pros / Cons...

Currently my internal drive is out of space due to my Aperture files. I want to place Aperture on a external drive to work from verses in intnal drive. In addition, I want to back-up all my work to another external for safe keeping. Once I move aperture to the external, I want to delete it off my internal drive. Does this make sense to do? Pros / Cons....

It is common for people to move their Aperture, iPhoto, iTunes etc. files to an external drive when those files become too large to conveniently keep on the internal drive.
The best approach is probably to keep the applications (iPhoto, Aperture etc.) where they are now, but move the files (photos, music, videos etc.) to the external drive.
You should set up a process to regularly backup all the files from both the internal drive as well as the external drive you'll be using. Here are two approaches:
(1) Use Time Machine. You can configure Time Machine so that it backs up both the internal drive as well as the external drive, all to a third separate backup drive. This is done via the Options button in the Time Machine preference pane.
(2) You can use a "cloning" program, such as SuperDuper, Carbon Copy Cloner, to make complete copies of files on your internal drive and that external drive. One way to do this is to use a very large disk for the backups, and to partition it into two backup drives, making one dedicated to the internal, the other dedicated to the external.
Two separate types of backups are recommended. I use both (1) and (2) above, and I disconnect and shut down the clone type backups when not being used. That way a power failure or surge that might destroy the original disk(s) plus the Time Machine backup(s) would still not damage the backups made under (2).
Don't delete your original Aperture files until you have verified that they are working properly from the external drive AND you have made a backup of them.

I think the DVD player reader on my Mac is going bad. Is there a way to copy the files off of an Apple Install DVD onto an external drive and then do theinstall from the external drive?

I think the DVD player reader on my Mac is going bad. Until I get it fixed Is there a way to copy the files off of an Apple Install DVD onto an external drive and then do theinstall from the external drive? It's ILife 11 if that makes a difference. Finder won't let me see the files to copy. I know - dumb question.
Thanks.
Bob

Adding an SSD is not a simple endeavour like adding additional memory or adding another hard drive to a Mac Pro. That's probably why the option is only offered as an option at the time of purchase. Even if your Apple store was willing to install the necessary parts you will probably be paying for 1-2 hours of labor plus the cost of purchasing the necessary service parts (SSD, bracket, cables, etc) which I suspect will make the upgrade cost much higher than what it costs to add the SSD option when purchasing a new system.
I use my system for business and need it to work reliably. Even though I'm fairly handy with tools I would not be willing to risk damaging my system and voiding my warranty by opening my system and removing the logic board and several other parts in order to squeeze in an SSD option and attach the appropriate cables and brackets. I'm also not prepared to deal with the hassles of explaining why my system has unauthorized parts installed in the event I experience issues and need to make use of my Apple warranty. My time is valuable, so I would probably investigate external storage options, or if I needed the speed of an SSD, I would consider selling my existing system and then purchase a new system configured with an SSD.
If you haven't already done so I suggest doing a search on 'iMac SSD installation' to see what's involved. It might help you understand why the SSD option is not offered post purchase.

Want to run iTunes from an external drive, how?

I want to run iTunes from my external drive, I have already made back ups of my library and media files but I can't figure out how to save iTunes to the external drive? When you download itunes it just automatically downloads to the computer. Can you even do this? If not, how can I use the saved info on my external drive (library and media files) with my itunes on the computer. The problem we are trying to solve is a lack of space on our computer and we want to free as much space as possible. Thanks!

I want to run iTunes from my external drive, I have already made back ups of my library and media files but I can't figure out how to save iTunes to the external drive?
Drag the iTunes library to the external drive, launch iTunes with the Shift key held down, and point it there.
(56927)

My one computer's gone for repairs, all my iTunes info is on an external drive. I just bought a new machine, I want to use iTunes on it with my original external drive. How can I do this?

Hi, I have an important question which I need to ask you folks.
For the past four years, I have been using iTunes on my laptop, the only computer I have had to use iTunes. All of my movies, songs, etc are saved to an external hard drive which connects through its USB port.
That laptop is not currently working, and for the past couple of months has been upstate at a friend's house, as he is attempting to fix it.
I just got a new portable tablet capable of running iTunes today. I have not set it up yet has I have been busy at work; but I want to have the tablet have iTunes on it as well under my existing iTunes account, but I am not sure exactly how to go about it. This will be my second computer machine that iTunes will be installed under, and I want to be able to plug into it the external hard drive, The exact same hard drive I have been using on my old computer with all my iTunes information on it.
How do I do it?

If the iTunes database files are on that drive, launch iTunes with the Shift key(Windows) or Option key(Mac OS X) held down, select Choose Library, and navigate to it. The computer may need to be authorized to play protected content, and if the library contains rented movies, those won't play.
If not, import the content to an iTunes library.
(100371)

Can I install Tiger as a boot disk on external drive

I upgraded to Leopard 2 months ago and everything works well except a program called Avid Express Pro. Avid suggests I go back to Tiger, but I like many of the features in Leopard. I'm using a Macbook pro with an intel processor. Is it possible to install Tiger on an external drive and boot from that drive when I want to use Avid, then restart on the internal drive for normal operation? I've tried installing Tiger on an external drive I have, but the installer won't let me select the external. Any help would be appreciated.

Your Intel MacBookPro can install Tiger or Leopard to any external drive that has been formatted with a GUID partition. It can be USB or Firewire. I'm using a miniStack v3 500gb FW800 drive for my MBP. When it arrived from OWC it was APM and Leopard or Tiger would refuse to Install to it. Disk Utility fixed this by repartioning the drive and choosing the GUID option and HFS+.
The GUID partition scheme is probably the problem. Most external drives come formated for DOS (Fat32) or the APM (Apple Partition Map). The Intel macs require GUID for Installing and Updating, but work fine with the APM drives for files.
You Intel Mac can boot from an APM drive, but not install to it. You can use SuperDuper to clone a bootable copy of your OS from your internal GUID drive to an external APM drive and the machine will boot from it, it just can't be updated.
Use Disk Utility to check the Partition Map Scheme on your external drives before you try to use one to install to.

Install / Use Organizer from an External Drive

Am I able to install and use the Elements Organizer on an external hard drive? I don't want to keep all my images on my laptop HD.
Am I able to put the images on the ext. HDD and then 'point' Organizer at them ~ OR ~ am I able to simply put the Elements Organizer
Application on the ext. HDD and load images into it and then be able to access it from my laptop?
I'm not able to locate a Discussion Group specifically for Elements Organizer. (?)

Hi,
You've posted on the right forum
You should install PSE on the laptop hard disk and may have all your images on the external hard disk or local hard disk. Now in Organizer, you may import media from local/external hard disk. Organizer only keeps only references (image path, to be precise) only and hence your images may reside on external hard disk.
Thanks
Andaleeb

Thunderbird re-install cannot find mail accounts from previous C:\ drive

QUESTION; Where do I go from here?
NARRATIVE:
My C:\ drive (!Tb) started to balk when after I had a little more than 800Gb stored on it. My tech told me the machine case would hold two internal HDs. We bought an additional 1Tb HD and he installed Windows basics, all drivers, and my regular backup utility so we could make an immediate mirror image of the drive on an external HD.
Both internals carry Windows 7 64-bit, and by editing Boot Config, I can boot from either -- with no errors or red flags.
I downloaded TB 31.0, installed it to the new drive; then copied out App Data and Application Data including all TB files from the old HD (2 Windows User accounts) to discreet folders on an external drive. From there, I copied them to the appropriate folders for the two Users on the new HD. Thunderbird will not access them, even though I have used every workaround and trick I have learned with TB over a dozen years. I've worked on this many days, checked several similar items on the forum, and don't see a solution. (And my tech has never wanted to learn anything about Tbird; nor has he needed to in times past.
I have just uninstalled Thunderbird 31.0 and deleted the content under TB folders in App Data (2) and Application Data (2) on the new C:\ drive. I first confirmed that all previous data is available on the old HD and that the copy on the external drive is complete and accurate -- and without any Windows security locks. Local Settings folders on both old-drive/Users were locked and could never access them, but some TB-related files were in there in times past.
What should I do? 1) Install an older version of Thunderbird and hope that I can marry the old files in? or, 2) What can you suggest?
Many thanks in advance. edj.

I resolved the problem with a 3rd drawer solution (not the best). I put all previous TB Profiles (with all mail folders) aside; then set up new TB accounts accessing Gmail and Yahoo mail.
Once I have drained the servers of all the accumulated mail, I will go through the old folders (under the old Profiles) and carefully, one at a time, move the folders I need to keep into the Local Folders account. That method appeared in another related post; practical, easy enough, and it got me off dead-center.

I want to install OS X 10.3 from an external drive

Similar Messages

Maybe you are looking for