If i purchase a new airport base station can I use my old airport extreme 802.11n (3rd Gen) as both an extender of my wife for multiple iphones and as a router?

I operate an old airport extreme base station 802.11n (3rd gen).
There are 4 iphone5's and 1 iphone4 on my network along with 2 laptops running 10.6.8 and 10.7 respectively as well as two desktops with the same configurations as the laptops.
I get a sense that the iphones may/will be useless the new airport.
Can I use the old base station (operating as an extender/bridge/router) so that older equipment will operate in the short term until they are upgraded?
Thank you.

I get a sense that the iphones may/will be useless the new airport
They will work fine with a new AirPort base station. You can use an iPhone or iPad to set up and configure the new base station. If you want to use a Mac to set up and configure the new AirPort, it will need to have at least Lion 10.7.5 installed. Mountain Lion 10.8 or Mavericks 10.9 could be used as well.
Can I use the old base station (operating as an extender/bridge/router) so that older equipment will operate in the short term until they are upgraded?
You can use the older AirPort base station to extend the wireless network. No updates will be needed to your iPhones or Macs.

Similar Messages

I have an 2tb time capsule 802.11n Wi-Fi base station can I use this as an external hard drive and use a new airport extreme 802.11ac Wi-Fi for my wifi?

I have an 2tb time capsule 802.11n Wi-Fi base station can I use this as an external hard drive and use a new airport extreme 802.11ac Wi-Fi for my wifi?

You can use the 2 TB Time Capsule as a network drive. That means that it must connect to one of the Ethernet LAN <--> ports on the new AirPort Extreme, or connect to the network using wireless.

Can I use an old Airport Extreme as an extender with a new Airport Express

Hi All, I have Verizon Fios and the data line runs into my bedroom. I purchased a new Airport Express today to replace the Airport Extreme (from 2006). Can I use the old Airport Extreme as an extender (I'd like to set it up in the basement as I get poor connectivity there). I tried using the Airport Utility - Other WiFi Devices to find the Airport Extreme, but it's not registering. Is what I'm attempting possible? If so, how do I set it up?

Can I use the old Airport Extreme as an extender
Is this the "round" or "dome" shaped AirPort Extreme?
If yes, then it is not possible to have the AirPort Extreme wirelessly "extend" the signal from the AirPort Express.
However, the older AirPort Extreme can probably be set up to provide more wireless signal coverage if it will connect back to the LAN <--> port on the AirPort Express using a permanent, wired Ethernet cable connection.
In this case, the setup of the older AirPort Extreme will require that you have an older version of AirPort Utility installed on your computer. If it is a Mac, then the Mac must be running Leopard (10.5.x), Snow Leopard (10.6.x), or a PC with AirPort Utility could be used to set up and configure the older Extreme.
f you have the "square" or "flat" version of the AirPort Extreme, then everything becomes much easier. Post back if you do.

How many AirPort Express stations can be supported by an AirPort Extreme wirelessly?

I got one AirPort Extreme in my home and would like to extend the wireless network by purchasing additional AirPort Express. Wanna know how many AirPort Express stations can be supported by an AirPort Extreme wirelessly?
Thanks.
Tony

Bob -- question for you which I can't answer as I don't have an airport extreme. The newer Extremes can create both G and N networks and can create the N network in the 5 mhz band. Can you increase the number of Express units you can connect wirelessly if you split the load between the 2.4 mhz G and 5 mhz N networks created by the Extreme. (recognizing that the 5 mhz band has less range than the 2.4 mhz band)
Not an issue for me as I only have three connected wirelessly, but I've always wondered about this. Of my three AX units one connects to a G network created by a Linksys WRT54GS and two connect to the N network created by the AX.
So instead of 3-4 AX units could it become 6-8?
Carlos

AirPort Extreme 802.11n (2nd Gen) no Guest Network capability?

I have an "AirPort Extreme 802.11n (2nd Gen)" according to a serial number lookup here.
I am not sure if this is the same as MB053LL/A which is mentioned is this archived thread. (Couldn't find a way to lookup the part number + couldn't find the tech specs at apple.com.)
I was wondering if this base station has the capability to setup a guest network in addition to the primary network.
According to the above mentioned Apple Discussions thread, the base station needs to have simultaneous dual band operation capability to make this possible. (Since I couldn't find the tech specs, I'm not sure what this base station has.)
I would assume from this Knowledge Base Article that the 2nd generation AirPort Extreme is one generation too old:
http://support.apple.com/kb/HT3477
Am I correct?
(It's set to "Share a public IP address" under Connection Sharing.)

Hi, flips01. You are correct. Simultaneous dual-band was introduced with the 3rd generation.

Airport Extreme 802.11N (5th Gen) frequent crash

I had bought an Airport Extreme 802.11N (5th Gen) that died a few months after purchasing it. I had the unit replaced via Applecare in May 2013.
The new unit's firs recorded crash was in August 2013. After that, it crashed sporadically, these instances were not recorded. In May 2014 it crashed twice in one day. Every time of a crash, I've had to effect a hard reset to factory presets and upload a saved configuration. This last time I reconfigured from scratch and saved the new config. Now it crashes regularly, every month since September. I have no idea what to make of it.
Considering that I had one of the original Silver units running for years (and upgraded with a more capable Orinoco card—if you know what I'm talking about, you know that's old!). I expected to get reliable service from this more advanced unit. So far, It's a bit of a dud.
Any ideas? Any diagnostic tools I can use to see what's happening? Does this run of Airport Extremes have "issues"? Should I bother getting one of the new tallboy unit?
Thanks.

I have found the Gen5 AE to be very reliable.
I would have blamed a dud unit.. except that you have had two of them.. So I would be tracing where the problem is apart from the AE.
What modem do you run? How is the AE setup in the network?
The older utility is of far more use than the one in Yosemite. So do you have available an older OSX version or even windows.. you can see the logs from the unit.. just like you could in the original B and G versions.
(and upgraded with a more capable Orinoco card—if you know what I'm talking about, you know that's old!
Know exactly what you are talking about.. Orinoco were most desired for their use with wifi scanners.
How is your power?? Apple stuff does seem to use stuff that is highly susceptible to spiking. I keep my network stuff on UPS. (or battery direct feed).
I also do not like 7.6.4 firmware.. I know others here might find it ok but I can clearly demonstrate worse performance with it. Direct A-B testing.
Take the firmware back to 7.6.1 and factory reset and see if you get any improvement.
To actually need to restore firmware settings is not normal.. so something major is wrong and in unusual way.. I think power is one key part of it.

How can I use my old AirPort Express?

How can I use my old AirPort Express (the one that plugs right into the wall without a power cable) to stream music to a stereo when I am using the new Airport Express? The AirPort Utility 6.1 will not recognize the old AirPort Express.

Apple does not make it easy for you to use an older device when they want you to buy newer devices.
See this link for tips on how to install a version of AirPort Utility on Mountain Lion that will allow you to configure your older Express:
http://www.macworld.com/article/1167965/mountain_lion_and_the_ancient_airport_ba se_station.html
This is not supported by Apple, so it is your decision on whether you want to move forward with this. It works fine for me, but I cannot guarantee that it will work for you, nor offer support if you have difficulty.

My Airport Base Station does not appear in the Airport Admin Utility

I cannot see my airport extreme base station in the Airport Admin Utility nor in Airport Setup Assistant via Airport. It worked yesterday but when I was trying to set up a network something must have changed but I don't know what it is. (The setup didn't work so I am only using one base station right now.) The only way I can configure/reconfigure the base station is by physically connecting via an ethernet cable. Then no problem. I have two computers and neither can access the base station with Airport Admin Utility via Airport. I have installed the latest Airport Update but nothing has changed. What happened?

You should be able to use the second Airport Extreme
Base Station as a wireless print server. What I
suggest you do is:
1. run the Airport Admin Utility and clean up
settings on your existing Base Station:
- under the Airport tab, make sure you have not
selected to "create a closed network"
- under the Access Control tab, clear out all
settings
- under the WDS tab, clear out all settings
- under the Network tab, make sure the box is checked
to "Distribute IP addresses" and "Share a single IP
address using DHCP and NAT".
- update settings to the Base Station if you changed
anything.
2. do a hard reset of your second base station per:
http://docs.info.apple.com/article.html?artnum=107451
3. for now, put both base stations and the Mac in the
same room. Run the Airport Setup Assistant, and use
its guidance to configure the second base station as
a new base station that "extends" the wireless
network of your main base station.
That should do it.
Thanks very much. The printer works great from both computers via my second airport base station. And I can see both my base stations in the Airport Admin Utility.

Using Airport Extreme 802.11n (5th Gen) router attached to local cable modem (time warner) I am trying to cover about 11,000 sf wirelessy but only get coverage in 75%-how can I increase my distance?

Thank you for pointing me to these articles. Please keep in mind that I am a total novice...this may be a dumb question: If you setup using the "preferred method" of a roaming network, how does having two wi-fi base stations connected to each other via ethernet extend the range to allow wireless access at a greater distance from the room you have this in?
Also, if you do the extended or the roaming network, are both units required to be "airport"? I have the Airport Express but I also have a Cisco Dual-Band Wireless-N Router - could I use this with the Aiport Extreme or do I need to purchase another Airport Extreme?

If you setup using the "preferred method" of a roaming network, how does having two wi-fi base stations connected to each other via ethernet extend the range to allow wireless access at a greater distance from the room you have this in?
When two or more wireless base stations are configured in a roaming network, they are all interconnected by Ethernet. Each base station will retain a unique base station name, but will use the same Network Name (also called SSID), wireless security type, & password. As far as wireless network clients are concerned, this type of network will appear as a single wireless network. You can literally walk (roam) with a laptop between routers and still be connected to the "same" wireless network.
In my case, I have a main Internet router that provides an Ethernet network (backbone) throughout my 2-story home. On each floor I have placed an AirPort base station that connects back to this main router. Both AirPorts are configured for a roaming network. This configuration allow me to be in any room on either floor and still get wireless Internet access.
Also, if you do the extended or the roaming network, are both units required to be "airport"? I have the Airport Express but I also have a Cisco Dual-Band Wireless-N Router - could I use this with the Aiport Extreme or do I need to purchase another Airport Extreme?
For an "extended" network, both units will need to be AirPorts. For a "roaming" network, they can be units provided by different manufacturers. Again, in my example, the "main" router is a Cisco RVS4000.

Can I use an old Airport Express to extend the range of a new Airport Express?

Hi all. I have an old Airport Express 802.11g (First Gen?) that is starting to fade. Still works, but not what it used to be. So I am going to buy a new Airport Express. I'm not interested in the Airport Extreme.
Question: If I use the new Airport Express as my main wireless router, can I plug my old Airport Express into another room as an extender? In other words, with the old Express and the new Express talk to each other or will a new Express only allow extension with another new Express?
Thanks!

Sorry, but the old AirPort Express 802.11 b/g does not have a setting to "Extend a wireless network", so it cannot be used as a extender with the newer AirPort Express if you plan to connect wirelessly.
If you plan to connect the older Express using a permanent wired Ethernet cable connection, then it could be configured to provide additional wireless signal coverage in that manner.

Can I use my old AirPort Extreme to extend my network?

I recently replaced my year-old AirPort Extreme with a Time Capsule. The TC setup was the easiest ever, and it actually asked if it was replacing the AirPort and used the old settings, network name, et al. Had it up and running in five minutes and all computers and devices attached to it without any changes necessary.
So now that I've got this AirPort, I'm wondering if I can use it like an Express and put it into the farthest reaches of my house to extend my network and attach it to my new Apple TV. I also have an old AirPort Express which isn't the 'n' model. What to do?

So now that I've got this AirPort, I'm wondering if I can use it like an Express and put it into the farthest reaches of my house to extend my network and attach it to my new Apple TV.
Yes, you could use the 802.11n AirPort Extreme Base Station (AEBSn) to extend the wireless range of the new TC. Whether or not, it will be successful, will depend on both at distance you are trying to cover and what form of Wi-Fi obstructions (walls, ceilings, floors, etc.) there are between the two routers.

Can i use my old airport with my PC?

I have a really old airport base station. its probably the first airport that ever came out. It still works great in my home, but now I would like to put a password on my home network, and I want to know if I can administer my device from a PC. I don't have a mac anymore. Thanks.

All those ports or on a fried logic board, so they would be of no use anyway.
Depending on how adept you are mechanically, you could gut the box and
figure a way of mounting a pair of 2.5" drives. and then connect the drives
to a pair of USB-to-SATA cables to them.

How many airport base station can you have at one time?

I currently have a abse and a abs dual ethernet. My set up is the cable is connected to the abse sending out g. The abs is daisy chain and sending out b. My c2d machine is communicating with the abse using g and my old G4 is communicating with the abs using b. I am doing this because I do not want the abse to communicate at b. When I go out to get the new n abse will I be able to add on to this or will I be or am I already wasting time and money. I just do not want any abs to downgrade to b. Any ideas or suggestions will be great.

If you add the new AirPort Extreme Base Station (AEBS) to your current configuration, you can set it up so that you have three separate (b/g/n) wireless networks. Each would have it's own Network Name (SSID) and set to only operate at their own specific 802.11 standard. To work the Base Station connected to the Internet source would be set up as a router, and the others in "bridge" mode.
Now, if you attempt to connect a non-n wireless client to the "n" network, it will degrade the performance a bit, but not down to either "g" or "b" level. This would be true of the "g" network as well.

How can i use my old airport express with my new imac and wireless hp print

i just bought my first imac (intel) and a wireless hp printer. i now realize that a wireless connection between my imac and my printer needs a router.
i have an airport express base station, which is a few years old. I can't find my documentation, so i don't know its specifications.
how can i find out the specs of the airport express i have and whether i can use it now? it says that it is model a1084 100-240v~ 0.2a 50-60 hz.
does that tell any knowledgeable people out there about the specs? can i search the apple website by serial number and find the specs?
thank all of you potential responders ahead of time.

Hi green jean
Try this > http://www.apple.com/airportextreme/features/printing.html
but also see > http://docs.info.apple.com/article.html?artnum=305293
Dennis

My Macbook (13" White) that I have had for three years recently had its screen die, and so I purchased a new macbook pro, since I cannot use the screen, how do I go about getting my information off of it such as my iTunes, iPhoto and other documents?

The screen would fade into these weird pastel stripes, and if I pinched the sides a bit it would return to normal, but a few weeks ago it stopped returning to normal. I would like to get my iTunes and iPhoto contents and my documents of various sorts off of it and onto my new macbook pro. A friend of mine removed the hard drive and got the information like it was an external hard drive. Can I do this? I don't know if I can use my migration assistant application because the screen of my macbook won't let me see anything to even log into my username on the computer... Help?

Firewire disk mode.
Plug in a foirewire cable, most likely need a 6pin (400) to 9 pin(800).
on the older machine, boot it up, and hold down the t key
HDD should show up on the new computer.
If you havent booted up the new machine, you could run migration assistant whith the above steps to pull the data off.

If i purchase a new airport base station can I use my old airport extreme 802.11n (3rd Gen) as both an extender of my wife for multiple iphones and as a router?

Similar Messages

Maybe you are looking for