Im Having a Problem with my wireless router

Hey all,
im having a problem my wireless router keeps dropin my net only way i can get back online is unplug the power cord on back of the router then plug it back in i try unplugin my cable modem and plug that back in before i unplug the power cord from my router i try seein if it was a cable modem problem but it wasnt so..its all in the router itself havin a problem.
Router: WRT54GS
i got two computers and xbox wired hook up to the router and laptop is wireless.
im thinkin my router already goin bad and i got it this year too.
i try goin to the live help on linksys site and they seem to be a computer person that was helpin me then some1 real so..i was hopin u all can help me more on my problem.

1) Try to keep the router in higher possition.
2) Try to use the device in the same room or open area.
3) You may try changing the wireless channel, default channel is 11, try to configure channel 6.
4) Upgrade the firmware.

Similar Messages

Pls help me.i have a problem with WRT54G wireless router.

Dear all, Now i got face some problem with WRT54G wireless router.The problem is after i connect to the internet...the wireless will automatic drop..is that any ppl here got face this and got any solution to solve it...?thanks for sharing..

hi...logon to router's setup page and try changing channel to 11, go to advanced wireless settings, try changing transmission rate to 54Mbps, beacon interval to 50, fragmentation and RTS threshold to 2304, also try upgrading latest firmwar on the router...check whether it maks any difference or not and let me know.

TS3048 I am having a problem with my wireless keyboard on my iMac

I am having a problem with my wireless keyboard on my iMac. Sometimes the keys seem to have a life of their own and I get a string of the same letter or symbol even though I only pressed the key once. Does anyone know how to rectify this?

Hello:
Try resetting the PRAM and SMC.
If that does not help, the KB is probably failing.
Barry

Problems with my Wireless Router since Mac Switch

Ever since my wife and I bought our MacBooks (we have one each) I have been having issues with my Linksys Wireless G Router.
http://www.amazon.com/Linksys-WRT54GS-Wireless-G-Broadband-SpeedBooster/dp/B0001 D3K8A
That is the one I have.
I use WEP encrypted, DCHP auto allocate on IP addresses and both machines are always within 20 feet of the router. However we get dropped connections to the router very often, almost daily, and it usually happens within a few minutes of booting a machine. The only way to restore the connection is to power down the router and restart it. This always works.
I've already tried the following. Changed the router channel from 5 to 7, in case there is interference. Changed the WEP password (it's 128-bit hex) and even tried limiting the DCHP allocations to two machines and adding Mac Addressing.
It could just be a hardware fault, but the previous machines (a PC laptop and an iBook G3) never had this issue. I did a router restart possibly once every 2 or 3 months. Now it's daily. Any advice?

Believe it or not I got the cheapest wireless router in the shop! A Belkin Wireless G router. It was easy to set up, supports all the standards, has great range and hasn't missed a beat since I installed it and it cost $35. All 3 home machines (2 MacBooks and a Windows desktop) all link via it flawlessly.
I nearly went for the base station from Apple, but at $200 it was hard to justify.
Looking around at some forums, the Linksys seems to have issues. I had the version 5. I also updated it to the most recent firmware about 10 days before I had this problem. My MacBook and my Wife's MacBook both disconnected from it the same day. By connecting manually (assigning a manual IP address and giving that address directly to the router) worked until you restarted, but would only work for one machine at a time.
When I saw the 2 MacBook Pro's in the cafe having EXACTLY the same issue, I was convinced it was the router. It had the same firmware version number mine did (ver 1.01)

WRE54G wireless extender problem with WRT600N wireless router

My Vista laptops work fine with the WRT600N router but not with the WRE54G extender. On the other hand my XP laptop works fine with the wireless extender so I know that both router and extender are working. Linksys tech support told me that the WRE54G is not compatible with the WRT600N, which is simply not true. With my XP laptop the signal goes from poor (5-10 Mbps) without the extender to excellent (54 Mbps) with the extender. Also, the lower blue light on the extender blinks indicating data transmission. I can access the setup page of the extender only with the XP laptop and wired desktop computers but not the Vista laptops. I suspect there is a Vista network setting that is the problem. I've turned off the firewall but to no avail. I've also switched between mixed mode and G-only, which made no difference. Anybody have any suggestions?

pfl wrote:
I have a secure wireless network (WPA). Perhaps my 4-5 year old XP laptop is the only laptop on the planet that works with the WRE54G-WRT600N combination. But I can assure all the doubters that this laptop categorically works flawlessly when I would otherwise be out of range without an extender. Good luck to spalaw. Please let me know if you are get your WRT160n to work with the WRE54G, especially you're able to connect with a Vista laptop.
Hi
I am Afraid and wont be surprised if ya all people are nt able to use a N series Router with a G series Range Expander !
the Reasons is simple - N series is not BackWard Compatible as u check out the sources around. (Back Ward Compatible means compatible with the previous versions for its wireless Band , e:g - G band and B band.)
as far as my experience is concerned regarding the Range Expanders , me and my bud wasted a whole Week Configuring a WRT350N and WRE54G v3 , and it worked somehow on the seventh day for an hour and Lost the connection again! Dayumm !
and we tried setting up with the same expander with WRT54GS v7.2 , it worked like a charm.
Conclusion : " WRE54G is a g series 2.4 Ghz expander which will work fine with all g series router though may not work with N Serious routers."
and if you really wish to Use something which can actually Extend the range for ur N routers signals , Better go for WAP4400N !!!!!!
And if someone still wish to run around , wanna try some tweaks (which i dont preferr )!
for WRT600N , just enable 2.4ghz band . as Range expander doesnt support 5 Mhz.
Use Only standard Channels . e.g : 1,9,3,11 .(No Wide and stuff.)
Try using WEP encryption first . (cause thats how we made WRT350N worked for a while. sighs)
At last , Wish u Luck.
Pe@c3
"What u Give , is wht u better start expecting to take back".. - http://Forsakenbliss.wordpress.com

Problems with linksys wireless router please help!

Me and my 2 flat mates share a wireless network, and for some reasons if cannot connect to it. I have vista home premium and a belkin dongle. We used a Linksys router to begin with, not sure which model, but we recently had to buy a new one because that did not belong to us. I can see the network so the dongle picks up the signal but every time I connect and put in the network key I either get Not close enough to the net work point (the router is about 5 meters away) The network key is incorrect (I created the password and it works on the other two people lap tops) The network has timed out. Sometimes I can connect to the network for a moment then it kicks me off. The connection wizard shows the network at full signal. I’m not sure what the problem is, I have done a full restore on my computer and the dongle was installed onto my computer via the disc it came with. I do have another dongle that is a Linksys one; however it does the same thing. Not sure what the problem is here, can anyone help before I have to go out and buy long network cable and have wires all over my flat i have a heap of work that needs doing this week so any ideas would be really helpfull

I would first try and bring your computer (if possible) closer to the connection point. That way it will have full time to connect. Also sometimes some materials in the walls mess with connections due to the type of material. Sometimes if your IP address is not quite right you will connect but then get booted offline. Sometimes if you don’t broadcast your ssid you cannot connect. (one of my Visa Networks does this ssid broadcast must be on).
Are you using WPA or WEP because Sometimes WEP is not as stable with some wireless modems/ so changing to WPA might solve your problem
With Knowledge… Impossible means nothing.
Credentials
Computer experience: 11 years
Cisco networks experience: 8 years
Network administrator: 6 years
N.E.T. networks experience: 6 years
Linksys networks experience: 6 years
Recent additions: A+ | Networks+ | Linux+ | Security+

I have a problem with my wireless router wrt54g. 360 help

So, let me explain my setup.
wireless router wrt54g has 1 wire connecing a home computer to the internet
Laptop is wireless
I tried connecting my 360 to my laptop (with a wire) and having a shared internet connection so that i could connect to the internet.
YET! when i connect my 360 to my laptop, it dissconnects MY LAPTOP from the internet. Weird phenomenon i know.
ALSO
whats nat? When i connect with a ethernet cable, it says this when i try to join a game

this video was able to help me out
http://www.youtube.com/watch?v=6NIyo2kJEG4

My Atv2 is very slow movies and shows take forever to load it plays for a few minutes then pauses again. I thought if was a problem with my wireless router but I replaced it with a new airport extreme and the problem persists. Air play is just as slow.

My Atv2 is very slow with both AirPlay and rented and purchased content I spoke to apple rep and tried the things he suggested but the problem persists. Now it requires more lead time then the lenght of material being viewed. I haves broadband internet connection and airport extreme router so I don't think this should be a problem. Lately every time the unit goes to the screen saver an error message come up saying there was an error while loading content please try again later and you have to all over again. It is extremely frustrating. Any suggestions? What speed of transfer should I expect using AirPlay ?

I'm having the same issue. Ay fixes? Bought ATV today, music streams but videos don't and mirroring doesn't work either. Start mirror and severe lag then just drops. Been trying for couple hours. About ready to return it.

Problem with my wireless router?

So, I recently installed the Linksys WRT54G2. It was easy, so I grabbed my iPhone and checked if the Wi-Fi was been detected. Yes, the network name Linksys appeared and it was working already. I didn't want to leave my network open for all my neighbors to have access, so I created a name and a password. After that, it seemed ok still. Again I grabbed my phone and saw the network with the name I created along with the little lock to the side. So it was definitely locked now, I clicked on it to use it and asked me for my password. I entered my password, but it wasn't working, it says "unable to join network" on my phone. I know is the right password and my phone has nothing to do with it, because the network is been detected but I just can't access it as if it was the wrong password. I tries creating new name and passwords and resetting the router but the same thing happens. It seems that it only works if I leave the network unlocked. I don't wanna do that. Cause then everyone is going t

For your wireless security be sure to use WPA2 Personal with passphrase.
On the iPhone forget the wireless connection used previously. Then reconnect and it should ask you for the new passphrase. When entering the passphrase into the iPhone check off show password so you can see if you have any typos in the passphrase
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

VPN problems with ActionTec wireless router

I'm trying to set up VPN from my Win7 laptop to my Win7 desktop to use while travelling.
I have an ActionTec GT704WGB and cannot VPN from my laptop on the Internet in to my desktop on this router. Using the Microsoft VPN test tools pptpsrv and pptpclnt I can successfully send VPN test messages (Port 1723 and GRE Protocol 47) between the two machines on my subnet, bypassing the ActionTec, so I know that Windows and Norton Internet Security are not the problem. But when I put the laptop on the Internet through another provider I cannot get any messages through the ActionTec. The ActionTec is configured (Security / VPN) to support VPN with Port 1723 forwarding and GRE * * * ). I am suspecting perhaps the ActionTec does not support inbound VPN but cannot find anything in the user manual or ActionTec support that clarifies one way or the other. I'm sure I used to be able to outbound VPN to my former employer's network.
It seems there is something about this router, or perhaps there is something in the Verizon network that does not support inbound VPN. Does anyone know?

The actiontech does support incoming and outgoing VPN connections. What changes possibly needed with your VPN setup or different port forwarding needed would need to be advised by the VPN tech support group.
Anthony_VZ
**If someones post has helped you, please acknowledge their assistance by clicking the red thumbs up button to give them Kudos. If you are the original poster and any response gave you your answer, please mark the post that had the answer as the solution**
Notice: Content posted by Verizon employees is meant to be informational and does not supersede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or plan

I'm having problems with a wireless Logitech mouse

Since upgrading to ML i'm having problems with a wireless Logitech mouse that worked well prior to the update. I'm using the current Logitech Control Center software. No other mouse software is on my Mac Mini. If I use a Guest Aacount the problems ( wheel and back button ) are not present. Any suggestions?

You might try the Logitech support site. There are communities on there:
http://www.logitech.com/en-us/support/keyboard-mice-combos
Here is a link to drivers:
Logitech Drivers
You might check your home folder/Library to see if you can find a Logitec .plist.
You need to look in your user Library/Preferences for the .plist. Hold down the option key while using the Finder "Go To Folder" command. Enter ~/Library. Delete the .plist(s) for the mouse.
If you prefer to make your user library permanently visible, use the Terminal command found below.
http://osxdaily.com/2011/07/04/show-library-directory-in-mac-os-x-lion/
You might want to bookmark the command. I had to use it again after I installed 10.8.2. I have also been informed that if you drag the user library to Finder it will remain visible.

WRT350N - How to tell if it's V1 or V2? Having major problems with it

I have a WRT350N that I purchased about a year or so ago and I'm trying to figure out if it's V1 or V2. Seems like tons of people are having problems with this series. I was having problems with the wireless connection going dead constantly (5+ times a day). Since I work from home this was obviously not acceptable. I upgraded the firmware after talking with Linksys tech support. After that, the problem got much worse. Now the wireless connection goes down as well the router loses it's internet connection. I finally removed it from my home network and put my old reliable D-Link 614 back in place. It's been working fine and actually has way better range. Before I throw this WRT350 in the trash I would like to see if mine is V1/V2 and if there is anything I can do with it.
Thanks!
Matt

To find out the router's version number look at the bottom of the router, it should say Model Number : WRT350N, right next to the model number if it says V2 then it is version 2 else it is V1...I assume it should be V1...
If you have intermittent connection, you should download and upgrade your router's firmware from here
Follow these steps to upgrade the firmware on the device : -
Open an Internet Explorer browser page on a computer hard wired to the router...
In the address bar type - 192.168.1.1...Leave the Username blank & in Password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Now reset your router :
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
For Wireless Settings, please do the following : -
Click on the Wireless tab,
- Wireless Network mode should be mixed...
- Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
- Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WEP, Encryption should be 64 bit.Leave the passphrase blank, don't type in anything...
Under WEP Key 1 type in any 10 numbers please(numbers only and no letters eg: your 10 digit phone number) and click on save settings...
Please make a note of WEP Key 1 as this is the Security Key for the Wireless Network...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
Now see if you can locate your Wireless Network and attempt to connect...

Having many problem with wifi....after installing lion......

Having many problem with wifi....after installing lion......it connect with wifi but not with Internet and at the same time iPad 2, iPhone 4 works smooth......help......I have MacBook air without thunderbolt and mac mini

I had the same problem last night. Boot into OSX and reboot the router - fine. Boot into Windows and wrong. Here were my fixes:
Firstly, I kept all the settings on my router solid. Just leave them as they are. Boot into OSX and check the Network settings and make a note of your IP address and the router's IP address.
Second, boot into Windows, then open up your wireless connection settings and navigate through to the properties where you can set the IP address.
Third: Set the IP address to your routers IP address changing the last set of digits to a value between 5 and 255 (I have 8 devices so I set the last two digits to 10.) This will keep the IP static.
Tab through the Mask settings to default those.
Then set the default gateway to your router's IP address.
Check that the Network Adapter's setting has IPv6 disabled (uncheck the box)
Finally: Set the primary DNS server to 8.8.8.8 then the secondary to 8.8.4.4 and then reboot the router.
That's what got my connection running.

Problems with Verizon Wireless BlackBerry Tour BlackBerry OS 4.7.1.61 update:

Problems with Verizon Wireless BlackBerry Tour BlackBerry OS 4.7.1.61 update - I was anxious to download the update to see if it addressed the sticky trackball problems and the low volume issue when using a blue tooth device. However, in the process of updating my BB Tour yesterday, the install stopped on the 8th out 12 updates. After a couple of 'retrys', the BB error message on the desktop came up which instructed me to: i) disconnect the device, ii) restart the computer. iii) restart the loading process and, iV) restore my data by loading the loader back-up file using Restore. Unfortunately my Tour was left without any software and the Desktop manager couldn't recognize it. The error message on the Tour was 503. Called Verizon Wireless tech and bottom line, the only fix is a new Tour, which they're sending me. Anyone else having issues with the update? Also, does it address the trackball and blue tooth issues?

I had issues with the trackball and had to have my Tour replaced. I was told this model does not have a removable trackball so the entire phone has to be replaced. My current one is working OK but does stick a bit. Seems to get worse over time. My wife's tour is newer and so far she is not experiencing the problem. Have not experienced a problem with the Blue Tooth volume.
I have another issue with this upgrade that I am wondering if anyone else has seen. My wife has the Tour as well. She was prompted to do the upgrade and went through it. It appeared to work except it blew out her Contact Alerts. When we put them back in we can no longer get the sound to play when she receives an SMS message in her holster. Vibration works but doesn't do any good when it is in her purse. Phones calls, calendar alerts, alarms all work in holster. As soon as we delete the contact alert the default SMS alert will play in the holster. If she takes her phone out of the holster the Contact alert will play. My phone is still running 4.7.1.40 and this function works fine. I am thinking about trying to put her's back to my version if possible but not sure the best way to go about this

Having multiple problems with script - NTFS Permissions and AD Groups

Hi, all! I'm having multiple problems with my first script I've written with Powershell. The script below does the following:
1. Prompts the user for a corporate division under which a shared folder will be created, and adjusts variables accordingly.
2. Prompts if the folder will be a global folder or an office/location-specific folder, and makes appropriate adjustments to variables.
3. If a global folder, prompts for the name. If an office/location-specific folder, prompts for each component of the street address, city and state and an optional modifier. I've prompted for this information in this way because the information
is used differently later on in the script.
4. Verifies the entered information and requests confirmation to proceed.
5. Creates the folder.
6. Creates an AD OU and/or security group(s).
7. Applies appropriate security groups to the new folder and removes undesired permissions.
Import-Module ActiveDirectory
$Division = ""
$DivAbbr = ""
$OU = ""
$OUDrive = "AD:\"
$FolderName = ""
$OUName = ""
$GroupName = ""
$OURoot = "ou=DFS Restructure Testing OU,ou=Pennsylvania Camp Hill 4410 Industrial Park Rd,ou=Locations,ou=Camp Hill,dc=jacobsonco,DC=com"
$FSRoot = "E:\"
$FolderPath = ""
$DefaultFolders = "Archive","Customer Service","Equipment","Inbounds","Management","Outbounds","Processes","Projects","Quality","Reports","Returns","Safety","Schedules","Time Keeping","Training"
[bool]$Location = 0
do {
$userInput = Read-Host "Enter CLS Division: (W)arehousing, (S)taffing, or (P)ackaging"
Switch ($userInput)
W {$Division = "Warehousing"; $DivAbbr = "WHSE"; $OU = "ou=Warehousing,"; break}
S {"Staffing is not yet implemented."; break}
P {"Packaging is not yet implemented."; break}
default {"Invalid choice. Please re-enter."; break}
while ($DivAbbr -eq "")
write-host ""
write-host ($Division + " was selected.")
$FolderPath = $Division + "\"
write-host ""
$choice = ""
do {
$choice = Read-Host "Will this be a (G)lobal folder or (L)ocation folder?"
Switch ($choice)
G {$Location = $false; break}
L {$Location = $true; $FolderPath = $FolderPath + "Locations\"; $OU = "ou=Locations," + $OU; break}
default {"Invalid choice. Please re-enter."; $choice = ""; break}
while ($choice -eq "")
write-host ""
write-host ("Location is set to: " + $Location)
write-host ""
if ($Location -eq $false) {
$FolderName = Read-Host "Please enter folder name:"
$GroupName = $DivAbbr + " " + $FolderName
} else {
$input = Read-Host "Please enter two-letter state abbreviation:"
$FolderName = $FolderName + $input + " "
$input = Read-Host "Please enter city:"
$FolderName = $FolderName + $input + " "
$input = Read-Host "Please enter street address number only:"
$FolderName = $FolderName + $input
$GroupName = $DivAbbr + " " + $FolderName
$FolderName = $FolderName + " "
$input = Read-Host "Please enter street name:"
$FolderName = $FolderName + $input
$input = Read-Host "Please enter any optional information to appear in folder name:"
if ($input -ne "") {
$FolderName = $FolderName + " " + $input
$OUName = $FolderName
write-host
write-host "Path for folder: "$FSRoot$FolderPath$FolderName
write-host "AD Path: "$OUDrive$OU$OURoot
write-host "New OU Name: "$OUName
write-host -NoNewLine "New Security Group names: "$GroupName
if ($Location -eq $true) { write-host " and "$GroupName" MGMT" }
write-host
$input = Read-Host "Please confirm creation of new site/folder: (Y/N) "
if ($input -ne "Y") { Exit }
write-host
write-host -NoNewLine "Folder exists: "; Test-Path ($FSRoot + $FolderPath + $FolderName)
if (Test-Path ($FSRoot + $FolderPath + $FolderName)) {
Write-Host "Folder already exists! Skipping folder creation..."
} else {
write-host "Folder does not exist. Creating..."
new-item -path ($FSRoot + $FolderPath) -name $FolderName -itemtype directory
Set-Location ($FSRoot + $FolderPath + $FolderName)
if ($Location -eq $true) {
$tempOUName = "ou=" + $OUName + ","
write-host
write-host $OUDrive$tempOUName$OU$OURoot
write-host
write-host -NoNewLine "OU exists: "; Test-Path ($OUDrive + $tempOUName + $OU + $OURoot)
if (Test-Path ($OUDrive + $tempOUName + $OU + $OURoot)) {
Write-Host "OU already exists! Skipping OU creation..."
} else {
write-host "OU does not exist. Creating..."
New-ADOrganizationalUnit -Name $OUName -Path ($OU + $OURoot) -ProtectedFromAccidentalDeletion $false
$GroupNameMGMT = $GroupName + " MGMT"
if (!(Test-Path ($OUDrive + "CN=" + $GroupName + "," + $tempOUName + $OU + $OURoot))) { write-host "Normal user group does not exist. Creating..."; New-ADGroup -Name $GroupName -GroupCategory Security -GroupScope Global -Path ("OU=" + $OUName + "," + $OU + $OURoot)}
if (!(Test-Path ($OUDrive + "CN=" + $GroupNameMGMT + "," + $tempOUName + $OU + $OURoot))) { write-host "Management user group does not exist. Creating..."; New-ADGroup -Name $GroupNameMGMT -GroupCategory Security -GroupScope Global -Path ("OU=" + $OUName + "," + $OU + $OURoot)}
$FolderACL = get-acl ($FSRoot + $FolderPath + $FolderName)
$FolderACL.SetAccessRuleProtection($True,$True)
# $FolderACL.Access | where {$_.IdentityReference -eq "BUILTIN\Users"} | %{$FolderACL.RemoveAccessRuleAll($_)}
$BIUsers = New-Object System.Security.Principal.NTAccount("BUILTIN\Users")
$BIUsersSID = $BIUsers.Translate([System.Security.Principal.SecurityIdentifier])
write-host $BIUsersSID.Value
# out-string -inputObject $BIUsers
$Ar = New-Object System.Security.AccessControl.FileSystemAccessRule($BIUsersSID.Value,"ReadAndExecute,AppendData,CreateFiles,Synchronize","ContainerInherit, ObjectInherit", "None", "Allow")
$FolderACL.RemoveAccessRuleAll($Ar)
Set-ACL ($FSRoot + $FolderPath + $FolderName) $FolderACL
get-acl ($FSRoot + $FolderPath + $FolderName) | fl
$FolderACL = get-acl ($FSRoot + $FolderPath + $FolderName)
$ADGroupName = "JACOBSON\" + $GroupName
$objUser = New-Object System.Security.Principal.NTAccount($ADGroupName)
$objUser.Translate([System.Security.Principal.SecurityIdentifier]).Value
write-host $ADGroupName
write-host $objUser.Value
$Ar = New-Object System.Security.AccessControl.FileSystemAccessRule($ADGroupName,"ReadAndExecute","ContainerInherit, ObjectInherit", "None", "Allow")
Out-String -InputObject $ar
$FolderACL.AddAccessRule($Ar)
$ADGroupName = "JACOBSON\" + $GroupNameMGMT
$Ar = New-Object System.Security.AccessControl.FileSystemAccessRule($ADGroupName, "Modify", "ContainerInherit, ObjectInherit", "None", "Allow")
Out-String -InputObject $ar
$FolderACL.AddAccessRule($Ar)
Set-ACL ($FSRoot + $FolderPath + $FolderName) $FolderACL
} else {
$tempOUName = "cn=" + $GroupName + ","
write-host
write-host $OUDrive$tempOUName$OU$OURoot
write-host
write-host -NoNewLine "Group exists: "; Test-Path ($OUDrive + $tempOUName + $OU + $OURoot)
if (Test-Path ($OUDrive + $tempOUName + $OU + $OURoot)) {
Write-Host "Security group already exists! Skipping new security group creation..."
} else {
write-host "Security group does not exist. Creating..."
New-ADGroup -Name $GroupName -GroupCategory Security -GroupScope Global -Path ($OU + $OURoot)
$FolderACL = get-acl ($FSRoot + $FolderPath + $FolderName)
$ADGroupName = "JACOBSON\" + $GroupName
$FolderACL.SetAccessRuleProtection($True,$True)
$Ar = New-Object System.Security.AccessControl.FileSystemAccessRule($ADGroupName,"Modify","ContainerInherit, ObjectInherit", "None", "Allow")
$FolderACL.AddAccessRule($Ar)
$FolderACL.Access | where {$_.IdentityReference -eq "BUILTIN\Users"} | %{$FolderACL.RemoveAccessRuleAll($_)}
Set-ACL ($FSRoot + $FolderPath + $FolderName) $FolderACL
My problems right now are in the assignment/removal of security groups on the newly-created folder, and the problems are two-fold. Yes, I am running this script as an Administrator.
First, I am unable to remove the BUILTIN\Users group from the folder when this is an office/location-specific folder. I've tried to remove the group in several different ways, and none are having any effect. Oddly, if I type in the lines directly
into Powershell, they work as expected. I've tried the following methods:
$FolderACL = get-acl ($FSRoot + $FolderPath + $FolderName)
$FolderACL.SetAccessRuleProtection($True,$True)
$FolderACL.Access | where {$_.IdentityReference -eq "BUILTIN\Users"} | %{$FolderACL.RemoveAccessRuleAll($_)}
Set-ACL ($FSRoot + $FolderPath + $FolderName) $FolderACL
$FolderACL = get-acl ($FSRoot + $FolderPath + $FolderName)
$FolderACL.SetAccessRuleProtection($True,$True)
$BIUsers = New-Object System.Security.Principal.NTAccount("BUILTIN\Users")
$BIUsersSID = $BIUsers.Translate([System.Security.Principal.SecurityIdentifier])
$Ar = New-Object System.Security.AccessControl.FileSystemAccessRule($BIUsersSID.Value,"ReadAndExecute,AppendData,CreateFiles,Synchronize","ContainerInherit, ObjectInherit", "None", "Allow")
$FolderACL.RemoveAccessRuleAll($Ar)
Set-ACL ($FSRoot + $FolderPath + $FolderName) $FolderACL
In the first case, the script goes through and has no apparent effect because afterwards, I do a get-acl and the BUILTIN\Users group is still there, although when looking through the GUI, inheritance appears to have been broken from the parent folder.
In the second case, I get the following error message:
Exception calling "RemoveAccessRuleAll" with "1" argument(s): "Some or all identity references could not be translated."
At C:\Users\tesdallb\Documents\FileServerBuild.ps1:110 char:5
+ $FolderACL.RemoveAccessRuleAll($Ar)
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : NotSpecified: (:) [], MethodInvocationException
+ FullyQualifiedErrorId : IdentityNotMappedException
This seems strange that the local server is unable to translate the SID of a BUILTIN account. I've also tried explicitly putting in the BUILTIN\Users SID in place of the variable in the New-Object line, but that gives me the same error. I've
also tried the solutions given in this thread:
http://social.technet.microsoft.com/Forums/windowsserver/en-US/ad59dc58-1360-4652-ae09-2cd4273cbd4f/remove-acl-issue?forum=winserverpowershell and at this URL:
http://technet.microsoft.com/en-us/library/ff730951.aspx but these solutions also failed to have any effect.
My second problem is when I try to apply the newly-created security groups, I also will get the "Some or all identity references could not be translated." I thought I had found a workaround to the problem by adding the -PassThru option to
the New-ADGroup commands, because it would output the SID of the group after creation, however a few lines later, the server is unable to translate the account to apply the security groups to the folder.
My first Powershell script has been working well up to this point and now I seem to have hit a showstopper. Any help is appreciated.
Thanks!

I was hoping to stay with strictly Powershell, but unless I can find a Powershell solution, I may resort to ICACLS.
As for the problems with my groups not being translatable right after creating them, I think I have solved this problem by using the -Server parameter on all my New-ADGroup commands and this example code seems to have gotten around the translation problem,
again utilizing the -Server parameter on the Get-ADGroup command:
get-acl ($FSRoot + $FolderPath + $FolderName) | fl
$FolderACL = get-acl ($FSRoot + $FolderPath + $FolderName)
# Add the new normal users group to the folder with Read and Execute permissions
$GroupSID = Get-ADGroup -Identity $GroupName -Server chadc01.jacobsonco.com | Select-Object -ExpandProperty SID
$SIDIdentity = New-Object System.Security.Principal.SecurityIdentifier($GroupSID)
$Ar = New-Object System.Security.AccessControl.FileSystemAccessRule($SIDIdentity,"ReadAndExecute","ContainerInherit, ObjectInherit", "None", "Allow")
$FolderACL.AddAccessRule($Ar)
# Add the management users group to the folder with Modify permissions
$GroupMGMTSID = Get-ADGroup -Identity $GroupNameMGMT -Server chadc01.jacobsonco.com | Select-Object -ExpandProperty SID
$SIDIdentity = New-Object System.Security.Principal.SecurityIdentifier($GroupMGMTSID)
$Ar = New-Object System.Security.AccessControl.FileSystemAccessRule($SIDIdentity, "Modify", "ContainerInherit, ObjectInherit", "None", "Allow")
$FolderACL.AddAccessRule($Ar)
Set-ACL ($FSRoot + $FolderPath + $FolderName) $FolderACL
Going this route seems to ensure that the Domain Controller I'm creating my groups on is the same one that I'm querying for the group's SID to use in the FileSystemAccessRule. It's been working fairly consistently.
Still having issues with the translation of the BUILTIN\Users group, though.

Im Having a Problem with my wireless router

Similar Messages

Maybe you are looking for