IMac will not display

My iMac will not display anything on the built in monitor. I have hooked up an external display to the thunderbolt port and it works fine on the external. I have tried to detect displays and it still cannot find it. I have tried a SMC Reset and PRAM Reset and also reseated the ram.
The specs are:
2.8Ghz core i5
4 gb of ram
Thanks

Wireless Diagnostics - About
Also try turning off Bluetooth

Similar Messages

My iMac will not display my wireless networks, any suggestions?

I have 3 wireless netowrks in my house. My iMac will only display the one that is for my home automation system and it is not connected to the internet. Any suggestions on this? When I click the wireless icon at the top it only shows 1 network, it won't display my other network or my neighbours networks. When I try to add one of the other networks in my house, it will not find them.

Wireless Diagnostics - About
Also try turning off Bluetooth

TS1587 I tried everything, except for reinstalling the SO-DIMM memory modules. Still, my iMac will not wake up. Turning it on you can hear the fan run, but the display stays dark. Any ideas what to do? Thanks Maja

My iMac won't start up, or wake from sleep. I've tried everything, except for reinstalling the SO-DIMM memory modules. Still, my iMac will not wake up. Turning it on, you can hear the fan run, but the display stays dark. Any ideas what to do? Thanks!

Mac doesn't boot
Can you hear the fans and hard drive and see the white boot screen? Flashing question mark? The circle just runs and nothing happens? Only black screen and nothing else? These can be very helpful to diagnose the source of the problem. [1]
Flashing question mark [2]: This is usually a sign of a failed hard drive. This indicates that boot up volume can not be found.
Black screen: This is usually a sign of a failed logic board. There is no single reason for this and this may be caused by failed GPU, screen, CPU or RAM.
Circle of death/no circle/blue screen: This is usually a sign of a hard drive failure. This may NOT be a dead hard drive, just broken permissions or something
Gray screen/Apple logo/spinning gear or globe/prohibitory sign/folder with flashing question mark [3]: This could be a sign of faulty hardware but more likely a software issue, i.e. broken permissions, failed software update, etc.
[edit]
What to do
First, hold down the option key (also known as the alt key) just after you've pressed the power button. This should show all the available options to boot from, so if you have Windows installed through Bootcamp or a disk in your SuperDrive, you should be able to see them along with your OS X drive/partition. Select the OS X partition with arrow keys and press enter. Startup key combinations
If that doesn't help continue doing the steps from below:
1. SMC reset [4]. Shut down and unplug all cables including power cord for at least 30 seconds and then plug in power cord and keyboard/mouse.
2. PRAM reset [5]. Hold down option, command, P and R while booting. Start it when you hear the sound and don't let go before it reboots.
3. Safe boot [6]. Hold down shift while booting to boot into safe mode. If this works, open Disk Utility from Utilities and repair your permissions and verify the disk
4. Hardware test [7]. Insert the install disk (disk 1 in Mac which shipped with OS X 10.5.4 or earlier, disk 2 if shipped with OS X 10.5.5 or newer) and hold down "D" before the grey boot screen opens. Follow on screen instructions
5. Boot from install disk. Boot from the disk that came with your Mac. Hold C while booting. Select Disk Utility from top bar and repair permissions and verify the disk. Reboot normally and see if it works now.
6. Boot from another Mac (Firewire target disk mode). Connect the machines with a Firewire cable. Power on your Mac and press T. Select the other Mac's hard drive. Download the current OS X combo update. Run the combo update installer and select the drive that won't boot as the destination.
7. "Repair" OS X. Boot from the install disk as in point 5. and reinstall OS X. This should NOT erase any data, just replaces the system files which may have caused your booting problem. Now install the latest combo update for OS X and repair permissions on your drive with Disk Utility.
7.1. Install OS X into an external hard drive and then boot from it [8] and try to copy your data from the hard drive before proceeding. If you have done a backup recently, you don't have to do this.
8. Restore OS X from Time Machine backup. Boot from the disk that came with your Mac and choose the Time Machine restore option. This step will lose any changes made since your last backup but the system and your data will be put back to exactly as it was on that date.
8.1 Reinstall OS X. Boot from the install disk as in point 5. and select Disk Utility again. Now erase the whole hard drive and install OS X again. If you had a Time Machine backup and step 7 worked you don't have to do this.

IMac will not boot, hard drive file problem? Can't install OS in 2nd part.

The iMac will not boot. The Apple displays on the screen, the cursor spins for awhile, and then it loops into a reboot effort.
Last night, I was doing a lot of custom file sharing settings using the include enclosed folders option at the bottom of the Get Info window.
Question 1: Could that file sharing process have messed things up?
In an effort to get things going........ A few weeks back, I used Disk Utility to create a 2nd partition, with the intent of installing Ubuntu Linux there. I never attempted the install, as far as I can remember, while playing with the Ubuntu Live CD. So, I thought I would install 10.5.6 from the CD in the 2nd partition. But I get an error message that says "The installer could not create the folder "/Volumes/Ubuntu 9.10/BaseSystem.pkg.161nDNDdQ.""
Question 2: I also shared that partition, could that have caused the OS install failure?
Question 3: If I understand the book correctly, I can try to install the OS from the CD on the 1st partition, and not lose my data, correct? Unfortunately, I don't have any backup for the data, as I don't own any drives large enough yet to accommodate the data on the drive.
Question 4: Anyone have any other thoughts as to what ent wrong?

Hi, Grant.
Sometimes, it just pays to think on a problem. I awoke thinking, if it will boot the OS X install CD, it ought to boot my Ubuntu Live CD. And then, maybe I can change permissions on the first partition. As soon as I thought that, it occurred to me, if the problems are with the permissions, what if I used the OS X disk, and erased (formatted) the Ubuntu partition. That should set all the permissions on that partition back to default. Would OS X install then to the Ubuntu partition?
You better believe it did!! I'm typing this from the Mac after updating my 10.5.6 to 10.5.8 in the 2nd partition, and I'm booting from the 2nd partition.
I then did as you suggested, and from the Mac, I repaired the permissions to the first partition. But, the result was the same, there are a few permissions that do not match, and Disk Utility cannot, does not, or will not correct them.
I'm currently downloading the 10.5.8 combo update .dmg file. My thought is to burn that to a disk, and then install it over the version in partition 1. And trust that the current installation on partition 1 does not have any cross linked files that will destroy some data.
I do have some old ATA IDE drives I can hook externally to the Mac, and copy some of the information I have from the Mac to those drives before doing the 10.5.8 install.
Can you think of a better solution?

My 2011 IMac will not boot up past the White apple logo screen with the whirly circle

My 2011 IMac will not boot up past the White apple logo screen with the whirly circle. I have tried various commands but to no avail. does anybody have any advice?

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

Numbers will not display 3D charts on my new computer. I am running system 10.6.8. A 2D chart turns into a selected empty rectangle when I change it to a 3D chart. What do I do?

Numbers will not display 3D charts on my new computer. I am running system 10.6.8. A 2D chart turns into a selected empty rectangle when I change it to a 3D chart. What do I do? I am running iWork 9.1.

Hello
Numbers 2.1 under 10.7.2 on my iMac described below.
There is at least a thread describing what you get:
https://discussions.apple.com/message/15526080
It claims that it strike when the app is using the NVIDIA video card available in some macBook pro.
Yvan KOENIG (VALLAURIS, France) samedi 7 janvier 2012
iMac 21”5, i7, 2.8 GHz, 12 Gbytes, 1 Tbytes, mac OS X 10.6.8 and 10.7.2

Audio waveform will not display

I just bought a new iMac and have opened a previous FCE4 file with it. The sequence will not display the audio waveform at all... it used to do fine displaying the waveform on my Powerbook G4. I've toggled the preferences to display audio waveform globally and also for the individual sequence, to no avail. The audio does play back, just no waveform display.
Any help appreciated.
Jeff
Message was edited by: Jeff Morgan1

First, make sure the track settings aren't too low. If the track height is too small the waveforms won't show. If that's OK then quit the application and trash the waveform cache. If you don't know where that is look in your FCE system settings. It'll be at the bottom of the first panel.

ICal will not display correct "event" times

Have iMac (21.5-inch, Late 2012), OS X Yosemite (10.10 ) and iCal app suddenly will not display the correct Event times that I have designated in the little pop up box? Any ideas about what I can do to reset iCal or fix this annoying error in the app?
Thanks!
Marilyn

Hi,
Have you tried turning it off in iCal's Preferences and then back on again?
Best wishes
John M

After installing 10.6, 10.6.8 my iMac will not log out after the prescribed time. How do I fix this?

My iMac will not automatically log off/out after the prescribed time since I have installed Snow Leopard. It will continue to go to, in order at the prescribed times, Screen Saver, Display Sleep, Computer Sleep. But the next step - Automatically Log User Off after xxx minutes no longer functions. Assistance?

Anyone can help?????

G5 iMac Will Not Turn On - Power Supply Diagnosis?

My A1145 20" iSight PPC G5 iMac will not turn on - it doesn't respond to the power button. It had been shut down for a few days, I turned on the power and it booted up as normal, the desktop appeared and I was about to open the web browser when it suddenly went dead; the screen immediately turned off with no warning or noise. There is no fan or disk noise coming from it when the power lead is plugged in, just a very, very faint electronic hum from inside.
From reading various webpages, it seems possible that the power supply could have failed. Is there a simple way that I can diagnose this before deciding whether to attempt to replace it myself or not? I understand that there should be some diagnostic LEDs which could help identify a problem - I've removed the surround from the iMac and peeled back the black EMI film below the display but I'm not sure for what or where I should be looking (they seem to be easier to find on the 17" models).
Whilst I know a repair might not be cost-effective on such an old machine, I have 220GB of photographs, documents and music on it - none of which is backed-up - so I am very keen to get it working and backed-up as soon as possible.
Could anyone suggest how to diagnose the problem?

Hi there:
My experience with Macintosh computers has not included the G5 iMac even though I almost got one to replace a failed-under-AppleCare iMac G4 17" 1.25GHz after three/four major failures and no local support.
...So, I think you may be able to pull the hard disk drive out of that computer and see if an external enclosure could allow you access those files IF the drive spins up at all. Sometimes odd things happen, and the G5 iMac had some history of capacitor and other failures that could be a problem. I see there are a few free information guides here that may be helpful: http://www.ifixit.com/Device/iMac_G5
If the battery on the logic board was dead, but the computer kept in running condition by leaving it plugged in, once the computer was left unplugged for a time then the device may fail to start. There is a way to reset the power management chip (different names for same idea as technology moved forward) and that could help in the process of troubleshooting most power related issues in the PPC Macs of later G3/G4/G5 design.
There are troubleshooting items of interest in here http://www.apple.com/support/imac/g5/ ie: what to do when your computer won't turn on...
Sorry to not be of direct help in this matter.
Good luck & happy computing!

My iMac will not support Yosemite. I need Mavericks. How can I get Mavericks?

My pre-2009 iMac will not support Yosemite. It has Snow Leopard. Apple should let me obtain the latest OS supporting the Apple computer. Any suggestions?

Mavericks is no longer available. You will need to use Yosemite. You can get Mountain Lion, however:
Upgrading to Mountain Lion
To upgrade to Mountain Lion you must have Snow Leopard 10.6.8 or Lion installed. Purchase a redemption code at the Online Apple Store: OS X Mountain Lion. Mountain Lion is $19.99 plus tax. Use the code to redeem a download of Mountain Lion from the App Store. The file is quite large, over 4 GBs, so allow some time to download. It would be preferable to use Ethernet because it is nearly four times faster than wireless.
     OS X Mountain Lion - System Requirements
       Macs that can be upgraded to OS X Mountain Lion
         1. iMac (Mid 2007 or newer) - Model Identifier 7,1 or later.
         2. MacBook (Late 2008 Aluminum, or Early 2009 or newer) - Model
             Identifier 5,1 or later.
         3. MacBook Pro (Mid/Late 2007 or newer) - Model Identifier 3,1 or later.
         4. MacBook Air (Late 2008 or newer) - Model Identifier 2,1 or later.
         5. Mac mini (Early 2009 or newer) - Model Identifier 3,1 or later.
         6. Mac Pro (Early 2008 or newer) - Model Identifier 3,1 or later.
         7. Xserve (Early 2009) - Model Identifier 3,1 or later.
To find the model identifier open System Profiler in the Utilities folder. It's displayed in the panel on the right.
     Are my applications compatible?
         See App Compatibility Table - RoaringApps.
Upgrading to Lion
If your computer does not meet the requirements to install Mavericks, it may still meet the requirements to install Lion.
You can purchase Lion at the Online Apple Store. The cost is $19.99 (as it was before) plus tax. It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
     Lion System Requirements
       1. Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7,
           or Xeon processor
       2. 2GB of memory
       3. OS X v10.6.6 or later (v10.6.8 recommended)
       4. 7GB of available space
       5. Some features require an Apple ID; terms apply.
Or you can stay with Snow Leopard.

Please can somebody help, my imac will not start up, just chimes, apple sign then spinning cog. I have tried many key codes, no success, would really like to talk to someone.

please can somebody help, my imac will not start up, just chimes, apple sign then spinning cog. I have tried many key codes, no success, would really like to talk to someone.

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of the script have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts SerialATA 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports ' com.clark.\* \*dropbox \*genieo\* \*GoogleDr\* \*k.AutoCAD\* \*k.Maya\* vidinst\* ' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 "` route -n get default|awk '/e:/{print $2}' `" 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB ' com.adobe.fpsaud com.apple.AirPortBaseStationAgent com.apple.installer.osmessagetracing ' ' 1274181950 464843899 1233118628 ' 51 5120 files );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^$[0-9]+$ /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n-\t%s\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' s/[0-9A-Za-z._]+@[0-9A-Za-z.]+\.[0-9A-Za-z]{2,4}/EMAIL/g;/\/Shared/!s/(\/Users\/)[^ /]+/\1USER/g;s/[-0-9A-Fa-f]{22,}/UUID/g;' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: [^EO]|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { split("'"${p[41]}"'",b);for(i in b) print b[i];if(n<200) print "com.apple.";} ' ' $3~/[0-9]:[0-9]{2}$/ { gsub(/:[0-9:a-f]{14}/,"");} { print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { split("'"${p[41]}"'",b);for(i in b) print b[i]".plist";if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/^root$/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1100) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".(/private)?","");n++;print;} END { split("'"${p[41]}"'",b);split("'"${p[42]}"'",c);for(i in b) print b[i]".plist\t"c[i];if(n<500) print "Launch";} ' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| |\n","\\|\\|kMDItem'${p[35]}'=");sub("^...."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[43]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/{next};/%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";p="uniq -c|sed -E '"'s/ +\$[0-9]+\$\$.+\$/\\\2 x\\\1/;s/x1$//'"'";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1|p;b=b$1;} END { close(p);if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text$|(Bo|PO).+ sh.+ text ex)/) F=F" ("T")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / / { print "'"${p[28]}"'";exit;};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/\(L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9;} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ /V/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' ' /^find: /d;p;' "`S0 44 45`" ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ *$/d;s/^ */ /;' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps sudo\ crontab sudo\ iotop top pkgutil 'PlistBuddy 2>&1 -c "Print' whoami cksum kextstat launchctl sudo\ launchctl crontab 'sudo defaults read' stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' defaults\ read scutil sudo\ dtrace sudo\ profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil sudo\ lsof test osascript\ -e );c2=(com.apple.loginwindow\ LoginHook '" /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'|tr , \\\n" 'L*/Ca*/com.ap*.Saf*/E*/* -d 1 -name In*t -exec '"${c1[14]}"' :CFBundleDisplayName" {} \;|sort|uniq' '~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' :${p[35]}\" :Label\" '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message Req 'bad |Beac|caug|corru|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|n Cause: -|NVDA$|pagin|proc: t|Roamed|rror|ssert|Thrott|tim(ed? ?|ing )o|WARN' -k Message Rne 'Goog|ksadm|SMC:|suhel| VALI|ver-r|xpma' -o -k Sender fseventsd -k Message Req 'SL' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cght] ! -name .?\* ! -name \*ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true $ -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '/S*/*/Ca*/*xpc* >&- ||echo No' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,Ex}* {/,}L*/{A*d,Ca*/*/Ex,Co{mpon,reM},Ex,In{p,ter},iTu*/*P,Keyb,Mail/B,Pr*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -path \\*s/Resources -prune -o -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,mach_i*/*,pam.d/*,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t {/S*/,/,}L*/Lau*/*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' '+c0 -i4TCP:0-1023' com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' "+c0 -l|awk '{print(\$1,\$3)}'|sort|uniq -c|sort -n|tail -1|awk '{print(\$2,\$3,\$1)}'" );N1=${#c2[@]};for j in {0..9};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents XPC\ cache Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching SATA Descriptors );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};';done;A7(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0() { [[ "$v" ]]&&sed -E "$s"<<<"$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v"|sed -E "$s";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "${s[63]}"<<<"$v"`&&C1 1 $1;};for i in 1 2;do for j in 0 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;D20 0 $((N1+1)) 2;D10 0 $N1 1;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;D13 0 $((N1+9)) 59 50;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 14 12 14;D22 6 36 13 15;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D22 35 49 61 51;D22 11 17 17 20;for i in 0 1;do D22 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A2 19 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;D13 24 24 32 31;D13 25 37 32 33;A2 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D13 21 0 32 19;D13 10 42 32 40;D22 29 35 46 39;};D23 14 1 62 42;D12 34 43 53 44;D12 22 20 32 25;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 26 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D23 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 20 42 32 41;D13 37 2 48 43;D13 4 5 32 1;D13 4 3 60 5;D12 26 48 49 49;B3 4 22 57;A1 26 46 56;B7 22;B3 0 0 58;C3 47;D22 4 4 50 0;D23 22 9 37 7;A7;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report what happened. No harm will be done.
12. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

My iMac will not wake up

My iMac will not wake up by the click of the mouse or the space bar. I have to hit the power button and then I get a normal but inactive screen. A hard reboot is necessary to bring it back up. The only thing I can think of that I did differently within the past couple of weeks is to enable the firewall. Any ideas?

First, you can try resetting the SMU and if that doesn't work, try booting from your install disc and using Disk Utility:
   1. Insert the Mac OS X Install disc that came with your computer, then restart the computer while holding the C key.
   2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
      Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.
   3. Click the First Aid tab.
   4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
   5. Select your Mac OS X volume.
   6. Click Repair. Disk Utility checks and repairs the disk.
Then boot back to your internal drive and rpair permissions in Disk Utility there.

The "week" display for Calendar is screwed up. The whole week of days will not display.

The "week" display for Calendar is screwed up. The whole week of days will not display.

Sounds like a different problem but:
Since these threads aren't merged, I'm posting the same in several threads.
I've had the screen blank problem, the sound and copmputer were still on. I took the IMac in twice, got home, still not fixed.
But they used their own keyboard in the shop and couldn't reproduce the problem. I switched keyboards and so far so good. It's been 3 days now.
I'll keep folks updated. Don't get a new graphics card before you try a new keyboard.
Be sure to take the batteries out of your keyboard when testing another one as the board does not turn off if it is like mine.

Satellite A300 PSAG0A - Games Will Not Display in Full Screen Size

I have a large number of games installed on my computer. At least 90% of them will not display in full screen size but display in a small window with a large amount of black screen surrounding the window. I am running Windows Vista Home Premium 32 bit. However, I do not think it has anything to do with Windows as my husband runs the same games on his Toshiba Satellite L300, running exactly the same version of windows, and they all display in full screen size.
Altering the screen resolution makes no difference. And, of course, I do select the full screen option in the games.
Also, sometimes when I have been playing a game and then closed it I find that my desktop picture has shrunk to the smaller size - the same size as the window in which the game was displayed when I was playing it.
The games work fine in every other way, it is only this small screen size which is driving me nuts.
I hope that someone can help me with this!!

Yes, as far as I can tell I have the latest driver. But, even this is confusing to me because....
My graphics media accelerator is Mobile Intel(R) 965 Express Chipset Family. The installed driver version is 7.14.10.1329. The release date for this is 2007-09-13, as far as I can tell from web searches.
However, on the Toshiba website for driver downloads, the available driver version is 8.2.0.1012 PV. The date is 2006-12-28. I have downloaded this driver and attempted to install it. I get the message that it has been installed but, after rebooting and checking the installed driver version is still 7.14.10.1329.
Perhaps, the 8.2.0.1012 PV version does not actually install because it is older than the currently installed version. I would have thought that the driver version with the higher number would be the newer one, but perhaps this is not the case as the dates do not seem to support this theory.
So now I ask myself, firstly, if the driver available for download on the Toshiba website is not the newest one, then why is it there?
Secondly, if it is the newest one then why will it not install on my computer?

IMac will not display

Similar Messages

Maybe you are looking for