IOS deleted on Cisco Acces Point

Hello,
IOS of my access point 1130 was deleted after bad manipulation.
I have just a boot but not a flash on my AP. I can connect it just in console mode.
What is the procedure to restore the IOS?
Thanks for your help.

You should be able to follow the below link, and reload the IOS to the AP. Just make sure you grab the 1130 image
http://www.cisco.com/en/US/docs/wireless/access_point/1240/installation/guide/124h_c4.html#wp1078480
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered

Similar Messages

I want to use acces point air sap1602i e k9 first times i need default ip adress

hi
i want to use acces point air sap1602i e k9 first times i need default ip adress to setup
it is possible if not give me please solution

Hello fouadissam,
You can connect to the AP with a console cable and enter show ip interface brief, which will display the ip address.
If its connected to a network you can log into your switch and enter show arp | i xxxx.xxxx.xxxx(mac address of the AP).
The below link points to a configuration guide that may be helpful.
http://www.cisco.com/c/dam/en/us/td/docs/wireless/access_point/15_2_4_JB/configuration/guide/scg15_2_4_JB3a.pdf
Hope this helps,
Please remember to rate helpful posts.
Thanks.

I want to upgrade the IOS of my Cisco 2821 from Version 12.4(11) to v 15.1 (XB), but I have CCME v 4.2 (0), is there any problem if I only upgrade the IOS and leave the CCME as it ?

I want to upgrade the IOS of my Cisco 2821 from Version 12.4(11) to v 15.1 (XB), but I have CCME v 4.2 (0), is there any problem if I only upgrade the IOS and leave the CCME as it ?
Thanks

CME is part of the IOS, so you can't upgrade the IOS seperately from CME.
That said, if this is a production environment you should proceed with caution and be prepared to roll back as you may find bugs, etc.
You should also look at release notes and make sure your phone firmware will still work or needs to be upgraded too.
Brandon

Which Cisco Access Point is Waterprof ? (outdoor:BR1300 + AIR-ANT24120)

hi,
My questions to the community :
i have to choose for a customer some 50 Access points but that must have an external antennas with at least 8 dbi as gain and to be waterprof
for me the BR1300 + AIR-ANT24120 is a good choice if the BR1300 is Waterproof (For me :normaly all Cisco Access Point Outdoor must be WaterProof : but i want to have a confirmation with a document if possible )
and it's interessant to knew ,which Cisco Access Point is Waterproof ?
Think you All !
Zammit Ikbel

the 1310 is going to be waterproof, as is the 15xx product line, (152x and 155x). All this can be found in the data sheet for the AP.
That being said, you can also put any of the external AP into a NEMA enclosure, and have it be waterproofed, so long as the enclosure is rated as such.
HTH,
Steve

Can cisco MSE(mobility service engine) configured to work with non-cisco access points?

I understand that access points can be configured to forwards all the probe requests to cisco wifi controller. cisco MSE(mobility service engine) gets the probes from wifi controller to find the location of the mobile devices.
My question, can cisco MSE(mobility service engine) be configured to work with non-cisco access points?

No and the reason why is the NMSP communication from the MSE to the WLC. Other vendors don't support this so there is no communication happening.
-Scott

Delete disk backup recovery point

Hi Guys,
Am using DPM 2012 SP1 version 4.1.3313.0
Looking to delete the disk recovery points & using the script mentioned int he gallery - http://gallery.technet.microsoft.com/scriptcenter/DPM-2012-R2-Remove-6167f338
Somehow when i run the scripts and follow the steps till recovery points there are approx. 192 numbers out of which am not able to distinguish which one is tape and disk recovery point.
I changed my retention from 15days to 5days the older recovery points are not getting removed automatically instead of the scripts i have ran Removeinactiverecoverypoint.ps1, removerecoverypoint.ps1 & pruneshadowcopiesDpm2010.ps1
Somehow i managed to shrink but that not what am looking for. I want to delete the older recovery points than 5days and using that gallery script how can i identify which one is tape / disk recovery point.
Note: i dont want to delete the tape recovery points.
- Charles

Hi,
Please try this script and see if that works for you.
#Author : Ruud Baars
#Date : 11/09/2008
#Edited : 11/15/2012 By: Wilson S.
#edited : 07/25/2014 By: Mike J.
# NOTE: Update script to only remove recovery points on Disk. Recovery points removed will be from the oldest one up to the date
# entered by the user while the script is running
#deletes all recovery points before 'now' on selected data source.
$version="V4.7.2"
$ErrorActionPreference = "silentlycontinue"
add-pssnapin sqlservercmdletsnapin100
Add-PSSnapin -Name Microsoft.DataProtectionManager.PowerShell
#display RP's to delete and ask to continue.
#Check & wait data source to be idle else removal may fail (in Mojito filter on 'intent' to see the error)
#Fixed prune default and logfile name and some logging lines (concatenate question + answer)
#Check dependent recovery points do not pass BEFORE date and adjust selection to not select those ($reselect)
#--- Fixed reselect logic to keep adjusting reselect for as long as older than BEFORE date
#--- Fixed post removal rechecking logic to match what is done so far (was still geared to old logic)
#--- Modified to remove making RP and ask for pruning, fixed logic for removal rechecking logic
#--- Prompt for MM/DD/YYYY hh:mm:ss AM/PM - V4.7.2
$MB=1024*1024
$logfile="DPMdeleteRP.LOG"
$wait=10 #seconds
$confirmpreference = "None"
function Show_help
cls
$l="=" * 79
write-host $l -foregroundcolor magenta
write-host -nonewline "`t<<<" -foregroundcolor white
write-host -nonewline " DANGEROUS :: MAY DELETE MANY RECOVERY POINTS " -foregroundcolor red
write-host ">>>" -foregroundcolor white
write-host $l -foregroundcolor magenta
write-host "Version: $version" -foregroundcolor cyan
write-host "A: User Selects data source to remove recovery points for" -foregroundcolor green
write-host "B: User enters date / time (using 24hr clock) to Delete recovery points" -foregroundcolor green
write-host "C: User Confirms deletion after list of recovery points to be deleted is displayed." -foregroundcolor green
write-host "Appending to log file $logfile`n" -foregroundcolor white
write-host "User Accepts all responsibilities by entering a data source or just pressing [Enter] " -foregroundcolor white -backgroundcolor blue
"**********************************" >> $logfile
"Version $version" >> $logfile
get-date >> $logfile
show_help
$DPMservername=&"hostname"
"Selected DPM server = $DPMservername" >> $logfile
write-host "`nConnnecting to DPM server retrieving data source list...`n" -foregroundcolor green
$pglist = @(Get-ProtectionGroup $DPMservername) # WILSON - Created PGlist as array in case we have a single protection group.
$ds=@()
$tapes=$null
$count = 0
$dscount = 0
foreach ($count in 0..($pglist.count - 1))
# write-host $pglist[$count].friendlyname
$ds += @(get-datasource $pglist[$count]) # WILSON - Created DS as array in case we have a single protection group.
# write-host $ds
# write-host $count -foreground yellow
if ( Get-Datasource $DPMservername -inactive) {$ds += Get-Datasource $DPMservername -inactive}
$i=0
write-host "Index Protection Group Computer Path"
write-host "---------------------------------------------------------------------------------"
foreach ($l in $ds)
"[{0,3}] {1,-20} {2,-20} {3}" -f $i, $l.ProtectionGroupName, $l.psinfo.netbiosname, $l.logicalpath
$i++
$DSname=read-host "`nEnter a data source index from list above - Note co-located datasources on same replica will be effected"
if (!$DSname)
write-host "No datasource selected `n" -foregroundcolor yellow
"Aborted on Datasource name" >> $logfile
exit 0
$DSselected=$ds[$DSname]
if (!$DSselected)
write-host "No datasource selected `n" -foregroundcolor yellow
"Aborted on Datasource name" >> $logfile
exit 0
$rp=get-recoverypoint $DS[$dsname]
$rp
# $DoTape=read-host "`nDo you want to remove when recovery points are on tape ? [y/N]"
# "Remove tape recovery point = $DoTape" >> $logfile
write-host "`nCollecting recoverypoint information for datasource $DSselected.name" -foregroundcolor green
if ($DSselected.ShadowCopyUsedspace -gt 0)
while ($DSSelected.TotalRecoveryPoints -eq 0)
{ # "still 0"
#this is on disk
$oldShadowUsage=[math]::round($DSselected.ShadowCopyUsedspace/$MB,1)
$line=("Total recoverypoint usage {0} MB on DISK in {1} recovery points" -f $oldShadowUsage ,$DSselected.TotalRecoveryPoints )
$line >> $logfile
write-host $line`n -foregroundcolor white
#this is on tape
#$trptot=0
#$tp= Get-RecoveryPoint($dsselected) | where {($_.Datalocation -eq "Media")}
#foreach ($trp in $tp) {$trptot += $trp.size }
#if ($trptot -gt 0 )
# $line=("Total recoverypoint usage {0} MB on TAPE in {1} recovery points" -f ($trptot/$MB) ,$DSselected.TotalRecoveryPoints )
# $line >> $logfile
# write-host $line`n -foregroundcolor white
[datetime]$afterdate="1/1/1980"
#$answer=read-host "`nDo you want to delete recovery points from the beginning [Y/n]"
#if ($answer -eq "n" )
# [datetime]$afterdate=read-host "Delete recovery points AFTER date [MM/DD/YYYY hh:mm]"
[datetime]$enddate=read-host "Delete ALL Disk based recovery points BEFORE and Including date/time entered [MM/DD/YYYY hh:mm:ss AM/PM]"
"Deleting recovery points until $enddate" >>$logfile
write-host "Deleting recovery points until and $enddate" -foregroundcolor yellow
$rp=get-recoverypoint $DSselected
if ($DoTape -ne "y" )
$RPselected=$rp | where {($_.representedpointintime -le $enddate) -and ($_.Isincremental -eq $FALSE) -and ($_.DataLocation -eq "Disk")}
else
$RPselected=$rp | where {($_.representedpointintime -le $enddate) -and ($_.Isincremental -eq $FALSE)}
if (!$RPselected)
write-host "No recovery points found!" -foregroundcolor yellow
"No recovery points found, aborting...!" >> $logfile
exit 0
$reselect = $enddate
$adjustflag = $false
foreach ($onerp in $RPselected)
$rtime=[string]$onerp.representedpointintime
$rsize=[math]::round(($onerp.size/$MB),1)
$line= "Found {0}, RP size= {1} MB (If 0 MB, co-located datasource cannot be computed), Incremental={2} "-f $rtime, $rsize,$onerp.Isincremental
$line >> $logfile
write-host "$line" -foregroundcolor yellow
#Get dependent rp's for data source
$allRPtbd=$DSselected.GetAllRecoveryPointsToBeDeleted($onerp)
foreach ($oneDrp in $allRPtbd)
if ($oneDrp.IsIncremental -eq $FALSE) {continue}
$rtime=[string]$oneDrp.representedpointintime
$rsize=[math]::round(($oneDrp.size/$MB),1)
$line= ("`t...is dependancy for {0} size {1} `tIncremental={2}" -f $rtime, $rsize, $oneDrp.Isincremental)
$line >> $logfile
if ($oneDrp.representedpointintime -ge $enddate)
#stick to latest full ($oneDrp = dependents, $onerp = full)
$adjustflag = $true
$reselect = $onerp.representedpointintime
"<< Dependents newer than BEFORE date >>>" >> $logfile
Write-Host -nonewline "`t <<< later than BEFORE date >>>" -foregroundcolor white -backgroundcolor red
write-host "$line" -foregroundcolor yellow
else
#Ok, include current latest incremental
$reselect = $oneDrp.representedpointintime
write-host "$line" -foregroundcolor yellow
if ($reselect -lt $oneDrp.representedpointintime)
#we adjusted further backward than latest incremental within selection
$reselect = $rtime
$line = "Adjusted BEFORE date to be $reselect to include dependents to $enddate"
$line >> $logfile
Write-Host $line -foregroundcolor white -backgroundcolor blue
$line="`n<<< SECOND TO LAST CHANCE TO ABORT - ONE MORE PROMPT TO CONFIRM. >>>"
write-host $line -foregroundcolor white -backgroundcolor blue
$line >> $logfile
$line="Above recovery points within adjusted range will be permanently deleted !!!"
write-host $line -foregroundcolor red
$line >> $logfile
$line="These RP's include dependent recovery points and may contain co-located datasource(s)"
write-host $line -foregroundcolor red
$line >> $logfile
$line="Data source activity = " + $DSselected.Activity
$line >> $logfile
write-host $line -foregroundcolor white
$DoDelete=""
while (($DoDelete -ne "N" ) -and ($DoDelete -ne "Y"))
$line="Continue with deletion (must answer) Y/N? "
write-host $line -foregroundcolor white
$DoDelete=read-host
$line = $line + $DoDelete
$line >> $logfile
if (!$DSselected.Activity -eq "Idle")
$line="Data source not idle, do you want to wait Y/N ? "
write-host $line -foregroundcolor yellow
$Y=read-host
$line = $line + $Y
$line >> $logfile
if ($Y -ieq "Y")
Write-Host "Waiting for data source to become idle..." -foregroundcolor green
while ($DSselected.Activity -ne "Idle")
("Waiting {0} seconds" -f $wait) >>$logfile
Write-Host -NoNewline "..." -ForegroundColor blue
start-sleep -s $wait
if ($DoDelete -eq "Y")
foreach ($onerp in $RPselected)
#reselect is adjusted to safe range relative to what was requested
#--- if adjustflag not set then all up to including else only older because we must keep the full
if ((($onerp.representedpointintime -le $reselect) -and ($adjustflag -eq $false)) -or ($onerp.representedpointintime -lt $reselect))
$rtime=[string]$onerp.representedpointintime
write-host `n$line -foregroundcolor red
$line >>$logfile
if (($onerp ) -and ($onerp.IsIncremental -eq $FALSE)) { remove-recoverypoint -RecoveryPoint $onerp -confirm:$True} # >> $logfile}
$line =("---`nDeleting recoverypoint -> " + $rtime)
$line >>$logfile
"All Done!" >> $logfile
write-host "`nAll Done!`n`n" -foregroundcolor white
$line="Do you want to View DPMdeleteRP.LOG file Y/N ? "
write-host $line -foregroundcolor white
$Y=read-host
$line = $line + $Y
$line >> $logfile
if ($Y -ieq "Y")
Notepad DPMdeleteRP.LOG
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. Regards, Mike J. [MSFT]
This posting is provided "AS IS" with no warranties, and confers no rights.

Blackberry Z10 connection with an Aironet Cisco Access Point 1200

Hi everybody,
I'm trying without success a connection between a Blackberry Z10 and an Aironet Cisco Access Point 1200.
We have no BB Server, we would like just to connect the WIFI.
I've checked this points during the activation of the device:
There's no LEAP protocolle.
There's an EAP-Fast possibility.
There's Mac Address recognition possibility.
When we try to use the EAP-Fast possibility, we generate a .pac file, but i don't know where i can put this file so that the Blackberry recognize this file. I've search the whole day and didn't find anything... there's simply no explanation with the Z10 around the .pac file without a BB Server.
I've try the Mac Address recognition and it simply doesn't work (no error the search time is too long)
Every other older smartphones - Blackberry (there's 4 devices) are working.
Anyone have an idea about? a suggestion? a list of compatible WIFI Devices?
Thank you ahead.
Have a nice day.
Joel.

Sorry i don't understand your answer.
I'm not a developper but a system administrator.
I just would like to use a Balckberry Z10 with our Wifi/Router Aironet Access Point 1200.
not more.
Best regards,
Joel

Delete the DNS delegations pointing to this server

Good morning,
I'm getting ready to decommission my Windows Server 2008 R2 server and replace it with a Windows Server 2012 R2 (completely new hardware). After I decommission my current DC I will reboot it, change its IP address and name and then reboot it again.
I am then going to give the new server the old IP and name of my old DC (so basically the name and IP address of the active DC will not change). I'll then promote this server back into the domain. Since the new DC in the end will have the
same IP and NAME as the old DC, should I uncheck the "Delete the DNS delegations pointing to this server" when I decommission the old DC since the new one would have the same name? Thanks!

You can uncheck it and then promote it. Once done, make sure that the new DC is set under
Name Servers tab in your zones properties.
This posting is provided AS IS with no warranties or guarantees , and confers no rights.
Ahmed MALEK
My Website Link
My Linkedin Profile
My MVP Profile

Configuring Cisco Access Points 1602i Air-SAP-1602I-Z-K9

Hi everyone,
I am having touble configuring cisco access points 1602i. I have configured them and they are broadcasting SSID and clients are able to connect to them, but the only thing which is troublesome is speed. I have 100Mbps bandwidth speed but at access point I am getting speed between 17 to 25. Can anyone please tell me where I am gone wrong.
I have Juniper Srx210 configured as backbone for providing internet on fiber. Then further I have attached one POE switch (managable). From that switch I have attached 4 access points.
One more thing,two ports of Juniper is configured as Vlans, one for staff and one for students. I have attached this POE switch to Student Vlan, but haven't configured ports of POE switch as trunk. Please tell me do I have to configure ports as trunk on POE Switch. Is this the cause of slow bandwidth over access points.
I am also planning to go for Wlan Controller to manage Access points. When I contact my supplier about it, told me the following:
"You just need to convert the Access points to autonomous mode. Here are some details, there is no additional charge."
https://supportforums.cisco.com/message/3889653
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
http://www.youtube.com/watch?v=QQ_NuxdRhQ4
https://supportforums.cisco.com/docs/DOC-14960
I looked at the links but couldn't understand properly. Then I searched over the internet and found out that
"a cisco autonomous access point basically runs on its own while a lightweight access point uses a centralized device called a wireless lan controller to get its configuration. autonomous access points are managed individually, while the lightweight access points can be managed centrally. also, the switchport configurations to support both types of access points will differ. "
I didn't understand, why he suggested to go for Wlan controller and to upgrade access points to autonomous mode, when according to above finding, it says that autonomous access points runs individually.
Please advice.
I shall be thankfull

Hello Scott and Leo,
Thanks for all your help.
I have managed to install and configure 4 Access points and Now Access points are giving speed between 25 to 45Mbps. Still not enought but it sloving the purpose. Everyone is enjoying their face book. I will soon get the Cisco Wlan Controller as well. I dont know if there is a way to get more speed from these access points. I am ready to buy more equipments if required.
Anyway, today I need your guys expretise once again. As you know Junipr Srx 210 is configured for fiber internet to provide internet services to school. Now we are changing the building and transfering the line to new building. This time I want to use Cisco router in place of Juniper Srx210. But I need to know what model will support the current configuration for fiber. Would you please tell me what model/series router will be suitable for fiber internet and for implementing other restrictions.
I am attaching a picture of current jiniper Srx 210 for your consideration.
I shall be very thankfull to you
Sarabjit

PPPoE on Cisco Access Point

Hi, Im looking for possibility to configure Cisco Access Points for PPPoE and VPDN anybody knows pls reply to [email protected] tks

I think it is possible to configure AP to fucntion over PPPOE. But since AP is just a layer2 device, we also need a layer 3 device like router to support PPPOE. Without layer 3 device, it is not possible.

Setting up Acces point with WRT54GL

Hello everyone,
I'm very new to this wireless networking stuff.
I'm having some problems with my wireless router. My ISP provided me with a Huwaei wireless modem, but I reside in a two floor apartment and the ISP's modem does not brodcast well to the second floor, the signal is very low.
My difficulty here is that I'm trying to use my router to brodcast the signal to the second floor.
Is it possible to set up an acces point with with my Wi-Fi router ?
My idea is that the router would be placed in a different part of the apartment and clone the signal from the wi-fi modem and broadcats that signal. I want to place the wi-fi router in the second floor.
Is such an action possible?
Thank you very much for your help.
Solved!
Go to Solution.

You can set the WRT54GL as an Access Point, both your both the Routers should be Hardwired to each other..
To make both the Routers work wirelessly, its not possible.
To make both the Routers work each other, Connect the Ethernet Cable from the LAN Port of your Modem to the Lan Port 1 of the Linksys Router. Click Here and follow the instruction how to make your Linksys Router work with your Modem.

Acces points

Hi all,
Today, I installed an acces point in my house to cover the wifi signal where it was bad before.
This signal is great now on my Ipad and Iphone, but my Macbook pro (mid 2011) has a problem.
My Ipad and Iphone switch between the accespoints perfectly, they pick out the one that has best signal strength and probably the best RSSI.
My MBP however does not switch between the acces points it will keep locked on the one it initially connected to.
When I turn off WIFI and turn it back on again it will reconnect to the best available but it will not switch on itself.
Does anyone know what is wrong?
My wife's MBP (same version) does seem to work and switch perfectly.....
Thanks in advance.
Kind regards,
Dennis

Has this started recently after the last PS3 update? If so theres a thread on this and so far no fix yet. Just do a search. Other than that you need to set up static IP's for both your computers and PS3. There are tutorials on this site as to how to do this.
Help fight lag! Wire up that gaming machine!!!!!

AP1262 bridge to Non-Cisco Access Point?

I would like to use a Cisco AP1262 in a mobile command vehicle to bridge to any WiFi Access Point that I know the SSID and Pasword to. Will the 1262 Bridge to a Non-Cisco Access Point?
If so, any assistance in finding an example configuration would be appreciated.
Thanks,
Brian

Hi Brian,
Yes, you can configure 1262 as Universal Workgroup bridge where it will associate to any cisco or non-cisco root AP. You can only connect one wired client behind universal WGB.
You just need to configure "station-role workgroup-bridge universal <wired_client_MAC>" under radio interface of WGB. (1262)
Something similar should work for your 1262, if you want it in 5GHz, otherwise configure radio 0 interface for WGB
hostname WGB
dot11 ssid <SSID-NAME>
authentication open
authentication key-management wpa version 2
wpa-psk ascii <PASSWORD>
interface Dot11Radio1
encryption mode ciphers aes-ccm
station-role workgroup-bridge universal 068d.098a.d422 <- Ur wired MAC
ssid <SSID-NAME>
bridge-group 1
interface GigabitEthernet0
bridge-group 1
NB: I haven't tested this, so you have to test & confirm. If WPA2/AES is not supported then you may need to choose suitable security protocol & encryption mechanism.
HTH
Rasika
*** Pls rate all useful responses ****

Cisco Access Points Rebooting

Has anyone experienced a Cisco Access Point reboot itself, on it's own?

7 out of 17 are rebooting... but it's not isolated to one IDF it's different spots within the building.i will check the log in flash.
Hmmmmm ... And if you do a "sh version" to everyone of them it comes up saying something like "by power-on"?
If this is the case, you may also want to consider the copper cables between your Injector and your AP.

PPPoE and VPDN config. in Cisco Access Points

Hi, Im looking for possibility to configure Cisco Access Points for PPPoE and VPDN anybody knows pls reply to [email protected] tks

I can only comment on the wireless voice side. Phones will be setting the Qos (Cos and ip precedence) you will need all the devices in the network to understand these QoS and act apropiately, prioritizing voice over other data.
If you can't guaratee that all devices that the voice will cross will maintain those Cos/dscp settings and will prioritize the voice, you can't guarantee how the voice quality would be.

IOS deleted on Cisco Acces Point

Similar Messages

Maybe you are looking for