Is is possible to start the Appserver with DOS 'runas' command

I can do this with tomacat:
runas /user:myuser /pass:mypassword "location of tomcat"
is this possible with SUN appserver that comes with the STUDIO for
both the modes:
1)Normal Start
2)Debug

Not normal but you will need to feel the trackpad actually click, at the login (press hard left bottom corner).  Tap to click isn't available until you log and it can read your preferences.

Similar Messages

  • Could not start the listener with a domain user

    Hi all,
    I am working on Windows 2003 with Oracle 10.2.0.2 !
    With user "local system account", I can start the listener and I have no problems!
    after chaning the user that runs the listener from local system account to a domain user, I cannot start the listener again!
    (for the oracle service itself for the database, is it possible to change the user from local system to that domain user without problems)
    attached the error message when starting the listener with cmd.
    by starting the listener with the restart of the windows service, the listener crashed down after a few minutes
    do I have to set additional permissions for that domain user?
    thanks in advance
    Stefan
    C:\Documents and Settings\Administrator>lsnrctl start listener
    LSNRCTL for 32-bit Windows: Version 10.2.0.2.0 - Production on 17-JAN-2008 11:51:29
    Copyright (c) 1991, 2005, Oracle. All rights reserved.
    tnslsnr wird gestartet: Bitte warten...
    TNS-12537: TNS: Verbindung beendet
    TNS-12560: TNS: Fehler bei Protokolladapter
    TNS-00507: Verbindung beendet
    32-bit Windows Error: 109: Unknown error

    In this case I see three error messages:
    TNS-12537:     TNS:connection closed
    Cause:     "End of file" condition has been reached; partner has disconnected.
    Action:     None needed; this is an information message.
    TNS-12560:     TNS:protocol adapter error
    Cause:     A generic protocol adapter error occurred.
    Action:     Check addresses used for proper protocol specification. Before reporting this error, look at the error stack and check for lower level transport errors. For further details, turn on tracing and reexecute the operation. Turn off tracing when the operation is complete.
    TNS-00507:     Connection closed
    Cause:     Normal "end of file" condition has been reached; partner has disconnected.
    Action:     None needed; this is an information message.
    The most important is the tns-12560 error message, this means that an unsupported protocol exception was raised. Assuming you are using the same environment configuration when starting the listener with the local account and starting it with the domain authenticated user, then it has to do with permissions. Both the local administrator account and the domain authenticated user must belong to the ORA_DBA group, otherwise the user won't have enough privileges to start the listener.
    On the other hand, make sure the sqlnet.ora file includes this line:
    SQLNET.AUTHENTICATION_SERVICES= (NTS)
    If you use a domain user name, log on under a domain with username and password which has administrative privileges on each node
    ~ Madrid

  • Is there a possibility to start the VeriStand 2014 Gateway programatically using LabVIEW 2014?

    Hello,
    This is a reload of the Is-there-a-possibility-to-start-the-VeriStand-2011-SP1-Gateway because what worked in 2011 SP1 does no more in 2014.
    I ported the code from the previous topic, do do the same thing (calling "__cdecl Int32 StartVeriStandGateway(out Int32 handle)" in "C:\Program Files (x86)\National Instruments\VeriStand 2014\Data\NationalInstruments.VeriStand.Gateway.dll".
    Doing this from a .NET programme (console or windows process) or directly from a DLL node in LabVIEW 2014 seems to have no effect, knowing the .NET code worked in 2011 even when called from a Windows service.
    Is there a new way to do it?
    By the way, the "NationalInstruments.VeriStand.WindowsRegistry.GetInstallationDirectory()" method has disapeared from the assemblies.
    Best regards,
     

    Hi Jarrod,
    You're rigth, after PC reboot the Gateway starts when calling the DLL node (OpenWorkspace & GetSystemStatus are called with no errors), but when I try to ConnectToSystem the program stays blocked into the sub-vi, although the code works well if the Gateway was previously started normally by running VeriStand from Windows.
    I tryed to change the call policy in the DLL node (UIThread & any thread) but it seems doing nothing.
    Please find here joined the test files and debug capture of the stall.
    Best regards,

  • Si it possible to start the DB

    Hi all,
    I need some info on this
    we backup all the datafiles and controlfiles to the tapes.Now our company is concerned about the data stored in the tape .Is it possible start the Database with these files by someone who stores in the remote area.
    Ours is password authentication and we donot backup the password file and initora
    Message was edited by:
    Maran Viswarayar

    Maran,
    I think it's all down to the trust between the two corporations. If your company don't trust them can keep the security of your data then simply don't hire them.
    If you don't trust a person why you want to give the key of your home to him?
    I believe you can also try to encrypt your files using thirty party tool before sending them to the storage company. However that will prolong the recover time of your database.

  • When a warranty replacement in hand, is it possible to change the 4s with 5 by extra fees?

    when a warranty replacement in hand, is it possible to change the 4s with 5 by extra fees?

    Sadly, life is sometimes unfair. Although, I'm not certain why you feel you would be entitled to any form of upgrade. It is neither stated nor implied in any Apple literature.

  • I have a touchscreen laptop running Windows 8.1. Is it possible to use the touchscreen with Firefox? I've installed Firefox but it only works with the mouse etc

    have a touchscreen laptop running Windows 8.1. Is it possible to use the touchscreen with Firefox? I've installed Firefox but it only works with the mouse etc

    Hello Sirving575, sorry but the metro version of firefox has been cancelled, see : https://blog.mozilla.org/futurereleases/2014/03/14/metro/
    thank you

  • I installed a buyed version of Adobe Photoshop Elements 13. But is not possible to start the programm. I can read "There ist a problem, the program is not able to start". Is someone able to helb me?

    I installed a buyed version of Adobe Photoshop Elements 13. But is not possible to start the programm. I can read "There ist a problem, the program is not able to start". Is someone able to helb me?

    Without system information and other details we can't know what might be going on.
    Mylenium

  • I would like to ask if is possible to predict a future version of iOS can have the possibility to choose the color with which to write and be able to choose the character also...

    I would like to ask if is possible to predict a future version of iOS can have the possibility to choose the color with which to write and be able to choose the character also...

    Nobody here would have a crystal ball and know what Apple plans on doing in the furture.
    If you feel this feature is so important, you can let Apple know:
    www.apple.com/feedback

  • Is it possible to sync the iphone with my company's email server

    Is it possible to sync the iphone with my company's email server (Novell Groupwise)? I have the option of getting a blackberry or iphone. I want the iphone, but I also want to be able to sync it with my work email since I am away from the office a lot. I know I need to contact the IT department, but I thought I would try here to see what experiences people had with this sistuation. Thanks.

    Depends on what protocols they will allow (or can). If they open up POP or better yet IMAP access, then yes, sure. It is all about the protocols available to you (them). Though note, the iPhone checks on an interval where the Blackberry has emails pushed to it. So with iPhone, the min interval time is 15mins.
    Message was edited by: DaVBMan

  • Is it possible to pair the playbook with the BlackBerry Visor Mount Speakerphone VM-605?

    Can i listen to my music from my playbook with my
    vehicle's stereo system by using the Blackberry
    Visor Mount Spwakerphone VM-605?
    Is it possible to pair the playbook with the
    BlackBerry Visor Mount Speakerphone VM-605?

    From what I've seen here and @ Crackberry yes once you've gotten the 2.0 upgrade.
    Information Technology is fun! Play with IT.

  • Is it possible to connect the java with XL database

    Hi friends,
    Is it possible to connect the java with XL database.
    if it is possible can u send the detail for that .
    Thnax in Advance..............

    What the heck is a XL database?

  • Cannot start the weblogicServer with Java_Option=-native

    Hi *,
    when I start the weblogicServer with the option '-native' it failed. But when I start the server without
    this option it starts (even if the connection to db2 yet does not function, see the problem from me
    befor).
    Here is the startscript
    /usr/java_dev2/jre/sh/java $JAVA_OPTIONS -ms64m -mx64m -classpath $JAVACLASSPATH
    -Dweblogic.class.path=$WEBLOGICCLASSPATH -Dweblogic.home=. -Djava.security.manager
    -Djava.security.policy==/aeu/local/weblogic/weblogic.policy weblogic.Server
    Anybodey an idea, what I must change for this option and for what do I need the option? I find this
    in the documentation.
    Best regards,
    Frank
    Environment is: AIX 4.3.3, JAVA 1.2.2, WeblogicServer 5.1

    Hello,
    For WIley Introscope version 8.0+ Please see this installation guide.
    https://websmp103.sap-ag.de/~sapdownload/011000358700001995842008E
    You want to be on JDK5
    Excerpt:
    SAP J2EE 7.10 and JDK5 specific
    instrumentation, e.g. memory
    allocation. Do not activate for Java
    1.4!
    This is likely your issue.
    Regards,
    Paul

  • TS1363 I want to use an old 3 GS iPhone that is no longer in service as a phone now as just an iPod to play music. When I connect the phone to the computer with iTunes running, iTunes says it can't connect to the device because it didn't get a valid respo

    I want to use an old 3 GS iPhone that is no longer in service as a phone now as just an iPod to play music. When I connect the phone to the computer with iTunes running, iTunes says it can't connect to the device because it didn't get a valid response from the device. How can I get the system to recognize the phone, and let me rename it as my iPod, instead of my phone?
    As an aside, the current installed operating system on this old iPhone is 4.2.1, but that wasn't one of the selectable options in the operating system list dropdown below. Don't know if that makes any difference.

    Hi maddogdne,
    Welcome to the Support Communities!
    The article below may be able to help you with this.
    Click on the link to see more details and screenshots. 
    Using an iPhone without a wireless service plan
    http://support.apple.com/kb/ht3406
    Cheers,
    - Judy

  • Is it possible to start an application with parameters

    Hello together,
    I have written an application which is stored on a network. People from different computer start it to work with it. Now I have the problem, that I need some different configurations on each computer.
    Is it possible to start a labview application with parameters, like: application.exe -User_1
    The application should check the parametes and should switch to the needed configuration.
    Thanks a lot and best regards,
    Michael
    Solved!
    Go to Solution.

    Hi Michael,
    yes it is possible. First you have to activate the data transfer of your parameters. You can do it in the application builder. It is something like "send command line parameters to exe" which you have to activate. You will get the parameter in your program with the property "App.Args". It is an array with the exe name as the first element and one entry for each additional linked parameter.
    Hope it helps.
    Mike

  • Where to start the journey with conherence

    Hi All,
    I am new to coherence, so would like to know from where I can start exploring cohrence mechanism for caching. I'm trying to explore integrating coherence with webcenter server.
    while installing webcenter stand alone server, even coherence will also gets installed (I guess) since I can see in my middleware home a folder with name "coherence_3.6".
    How can I start using this with my webcenter application? Can anyone help me on this?

    Hi Venky,
    I would suggest you to learn the fundamentals of Coherence and start doing basic exercises and/or examples before integrating to WebCenter. I think the tutorial available at the URL below is very useful for people new to Coherence, as it explains step-by-step the basic installation (stand-alone first), the interaction with Java classes and the basic usage of the Coherence API and then more sophisticated steps like advanced features of Coherence, security, interaction with JPA and WebLogic. The tutorial can be seen at http://download.oracle.com/docs/cd/E18686_01/coh.37/e18692/toc.htm
    Also, I strongly recommend the "Oracle Coherence 3.5" book written by Aleksandar Seovic, Patrick Peralta and Mark Falco, which can be ordered below:
    http://www.packtpub.com/oracle-coherence-35/book
    http://www.amazon.com/Oracle-Coherence-3-5-Aleksandar-Seovic/dp/1847196128
    Finally, when you have certain knowledge of Coherence, you should be able to integrate it with WebCenter. The following URL may be useful for that: http://cfour.fishbowlsolutions.com/2011/03/09/using-webcenter-and-oracle-coherence-together-discussion-and-how-to/
    Hope this helps.
    Thanks,
    Cris

Maybe you are looking for

  • External hard drives not going to sleep

    External HDs (I have two) connected to my 2.26 unibody macbook are not going to sleep even though I have the appropriate check box selected in System Prefs. Running 10.6.8. Connected through the USB ports in my 23" cinema display. Any thoughts or sug

  • Header function in ADOBE X

    When we use the header function in ADOBE X and shrink the document to avoid overwriting, we get a line in the right margin which appears to be the end of the original page location.  How can we fix this issue?

  • Method of MatrixTransformer not defined?

    hi, everyone. when I use MatirxTransformer to rotate sprite, occure an error: 1061: Call to a possibly undefined method getRotation through a reference with static type fl.motion:MatrixTransformer. then I try another method of it, same error occured.

  • Run Time Error :OBJECTS_OBJREF_NOT_ASSIGNED

    Hi All, In ECC 6.0, for several employees minor changes in masterdata like changing the address, telephone no. etc. is resulting in a run time error <b>OBJECTS_OBJREF_NOT_ASSIGNED</b> <b>Short text</b>    Access via 'NULL' object reference not possib

  • Getting the most from my iMac

    Hi everyone, I've had my iMac for almost 2 months now, just switched from windows, and of course on windows you can defrag the hard drive and check for errors and so on. My question is, do you have to do that on a Mac? I want my machine to run the ab