ISDN BRI Call Blocked

Good Day
We have a IDN BRI connection to ISP.
We are seeing this error log in the router. Any body have seen this error log before?
000759: *Nov 18 13:01:04.652 : ISDN BR0 **ERROR**: process_bri_call: Outgoing call id 0x809B blocked
000760: *Nov 18 13:01:04.652 : ISDN BR0 **ERROR**: UserIdle: process_bri_call failed on call to 0321632168
000761: *Nov 18 13:01:22.547 : BRI0: wait for isdn carrier timeout, call id=0x809A
000762: *Nov 18 13:01:22.547 : ISDN BR0 EVENT: UserIdle: callid 0x809A received ISDN_HANGUP (0x1)
000763: *Nov 18 13:01:22.547 : ISDN BR0 EVENT: isdn_hangup: Hangup call to call id 0x809A ces = 1
000764: *Nov 18 13:01:22.547 : ISDN BR0 **ERROR**: CCBRI_Go: NO CCB Src->HOST call id 0x809A, event 0x5 ces 1
000765: *Nov 18 13:01:22.547 : ISDN BR0 EVENT: process_rxstate: ces/callid 1/0x809A calltype 1 HOST_QUERY_RESPONSE
000766: *Nov 18 13:01:34.644 : BRI0: wait for isdn carrier timeout, call id=0x809B
000767: *Nov 18 13:01:34.644 : ISDN BR0 EVENT: UserIdle: callid 0x809B received ISDN_HANGUP (0x1)
000768: *Nov 18 13:01:34.644 : ISDN BR0 EVENT: isdn_hangup: Hangup call to call id 0x809B ces = 1
configuration of the router.
ROUTER#sh run int BRI0
Building configuration...
Current configuration : 523 bytes
interface BRI0
description ***** ISDN Backup for ADSL *****
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1492
ip virtual-reassembly
encapsulation ppp
ip route-cache flow
ip tcp adjust-mss 1400
dialer idle-timeout 60
dialer string 0320544000
dialer string 2856000
dialer watch-group 1
dialer-group 2
isdn switch-type basic-net3
isdn point-to-point-setup
no cdp enable
ppp authentication chap callin
ppp chap hostname [email protected]
ppp chap password 7 XXXXX
end
ROUTER#sh isdn sta
Global ISDN Switchtype = basic-net3
ISDN BRI0 interface
       dsl 0, interface ISDN Switchtype = basic-net3
   Layer 1 Status:
       ACTIVE
   Layer 2 Status:
       TEI = 67, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
   Layer 3 Status:
       0 Active Layer 3 Call(s)
   Active dsl 0 CCBs = 0
   The Free Channel Mask: 0x80000003
   Total Allocated ISDN CCBs = 0

Actually I did.
When I upgraded the IOS on the router I mistakenly used the AdvanceIP services as we used that on all 871 routers. The 876 should, however have been upgraded with the Enterprise version.
The fault message was due to a license issue.
Took long time to figure this out and find something about it.

Similar Messages

Problem connecting isdn bri voice interface to pstn

i'm trying to configure my ISDN BRI NT/TE voice interface card (VIC-2BRI-NT/TE) on router 3825 to link to my PSTN provider. This must allow my Cisco IP phones to pass call to the PSTN through my call manager 4.1.
I suscribe to two isdn line. The provider told me that the SWITCH TYPE is VN6 (COTE d'IVOIRE or Ivory Coast).
For my bri configuration, see file "interfaces configuration..."
My problem is that when i pass call from my Ip telephony network, the first call goes well. But after this first call, when i type the command isdn status, i can see that the layer 1 of my isdn interfaces are DEACTIVATED, and after a few minutes, it turn back to ACTIVE. During these minuite, i can't pass any call through my isdn interface.
for outputs of show isdn status command, and isdn debug q931 commands
see file "show isdn status and debug..."
Notice: when the status of the isdn layer is in the deactvated status, i can receive call from the pstn, but i can't passe call to pstn (the state changes to ACTIVE when incomming call from pstn arrive, but still stay DEACTIVATED when outgoing call is initiated)
Please help me

I've entered the "isdn transition-delay 1" interface command and things seem to work well.According to the IOS help on my router,this command clears the ISDN D-CHANNEL after a delay of 1 second.
But i would like to get more information on this command, and also on the isdn layer 2 and 3 timers, and even possible on all the "isdn" interface command option.
THANKS

ISDN BRI INTERFACE

Isdn bri interface is used as backup by serial interface
backup delay 10 60
under bri interface following command is also configured
dialer idle-timeout 900
what will be idle timeout of bri interface if serial interface comes back and functional.

Hello Jabbar,
this looks like a cisco BCRAN question, here it goes:
the backup delay 10 60 , means that it will take 10 seconds before the secondary link comes up, after the primary goes down, and it will take 60 seconds after the primary goes back up, before the secondary goes down.
dialer idle-timeout 900:
this command indicates how long the call can stay idle before it is disconnected.
from cisco:
"This command is used on lines for which there is no contention. When contention occurs, the dialer fast-idle command is activated. For example, when a busy line is requested to send another packet to a different destination than it is currently connected to, line contention occurs and the dialer fast-idle command is activated.
By default, this command applies to inbound and outbound calls. For example, if a receiving system needs to make outgoing calls, you might configure it with a short idle timeout.
Only packets that match the dialer group reset the idle timer."
So, I guess it would be 900s
HTH,
please rate this post if it does,
Vlad

ISDN BRI layer 1 & layer 2 do not sustain "active" statuses

Hi Expert,
I have some routers which can not sustain the ISDN layer 1 & layer 2 statuses correctly. Whenever, the ISDN line is manually activated or the ISDN BRI ports are manually reset, the layer 1 & layer 2 statuses become active but they become deactivated after a while. I have changed the ISDN module and the same symptom is observed. Would you advise what is the cause and resolution. Your advice in this matter is greatly appreciated.
Thanks and Regards,
Jason Peh

Hi Rick,
Below is the show interface for BRI1/0,
router_2#sh isdn status
Global ISDN Switchtype = basic-net3
ISDN BRI1/0 interface
dsl 8, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
TEI = 66, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
Layer 3 Status:
0 Active Layer 3 Call(s)
Activated dsl 8 CCBs = 0
The Free Channel Mask: 0x80000003
router_2#sh int BRI1/0
BRI1/0 is up (spoofing), line protocol is up (spoofing)
Hardware is BRI
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Last input 00:04:39, output 00:04:39, output hang never
Last clearing of "show interface" counters 24w4d
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
27807 packets input, 207167 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
27921 packets output, 209138 bytes, 0 underruns
0 output errors, 0 collisions, 551 interface resets
0 output buffer failures, 0 output buffers swapped out
1680 carrier transitions
router_2#sh int BRI1/0:1
BRI1/0:1 is down, line protocol is down
Hardware is BRI
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Keepalive set (10 sec)
LCP Closed, multilink Closed
Last input 04:59:17, output 04:59:17, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 108 drops; input queue 0/75, 1 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
7434 packets input, 1689890 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
2 input errors, 0 CRC, 1 frame, 1 overrun, 0 ignored, 1 abort
10743 packets output, 782350 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
4682 carrier transitions
router_2#sh int BRI1/0:2
BRI1/0:2 is down, line protocol is down
Hardware is BRI
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Keepalive set (10 sec)
LCP Closed, multilink Closed
Last input 04:59:22, output 04:59:22, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 3 drops; input queue 0/75, 3 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
6902 packets input, 1530090 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
3 input errors, 0 CRC, 3 frame, 0 overrun, 0 ignored, 3 abort
7527 packets output, 594592 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
25 carrier transitions
I have another router with the same configuration and the statuses are able to sustain correctly. Thus, I doubt that the backup interface command has any effect on the layer 1 & layer 2 statuses.
Best Regards,
Jason Peh

ISDN BRI backup - Disconnect after 1 sec

There is a ISDN BRI backup to Serial IF on a router.BRI seems to be able to cennect with opossite site, but after 1 sec comes Disconnect(see attachment).I tried Floating static routes and Dialer watch as well, with the same result. Can anybode help me? Thanks

There is no aaa new-model statment on both side.I`ve rewrite user/psw and added ppp chap hostname ... command.
output of isdn status follows:
cpp-poprad#
Sep 20 14:52:00.647: %DIALER-6-BIND: Interface BR0/1/0:1 bound to profile Di0
Sep 20 14:52:00.651: %LINK-3-UPDOWN: Interface BRI0/1/0:1, changed state to up
Sep 20 14:52:00.651: %ISDN-6-CONNECT: Interface BRI0/1/0:1 is now connected to 0524684841 N/A
Sep 20 14:52:01.655: %ISDN-6-CONNECT: Interface BRI0/1/0:1 is now connected to 0524684841 cpp-poprad
Sep 20 14:52:01.655: %ISDN-6-DISCONNECT: Interface BRI0/1/0:1 disconnected from 0524684841 cpp-poprad, call lasted 1 seconds
Sep 20 14:52:01.659: %LINK-3-UPDOWN: Interface BRI0/1/0:1, changed state to down
Sep 20 14:52:01.659: %DIALER-6-UNBIND: Interface BR0/1/0:1 unbound from profile Di0sh isdn statu
Global ISDN Switchtype = basic-net3
ISDN BRI0/1/0 interface
dsl 2, interface ISDN Switchtype = basic-net3
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 71, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 2 CCBs = 0
The Free Channel Mask: 0x80000003
Total Allocated ISDN CCBs = 0
cpp-poprad#sh isdn act
ISDN ACTIVE CALLS
Call Calling Called Remote Seconds Seconds Seconds Charges
Type Number Number Name Used Left Idle Units/Currency
cpp-poprad#
Sep 20 14:52:18.295: %LINK-3-UPDOWN: Interface BRI0/1/0:1, changed state to up
Sep 20 14:52:18.295: %DIALER-6-BIND: Interface BR0/1/0:1 bound to profile Di0
Sep 20 14:52:18.299: %ISDN-6-CONNECT: Interface BRI0/1/0:1 is now connected to 05246848411 N/A
Sep 20 14:52:18.351: %ISDN-6-CONNECT: Interface BRI0/1/0:1 is now connected to 05246848411 cpp-poprad
Sep 20 14:52:18.531: %LINK-3-UPDOWN: Interface BRI0/1/0:1, changed state to down
Sep 20 14:52:18.531: %DIALER-6-UNBIND: Interface BR0/1/0:1 unbound from profile Di0sh isdn act

ISDN BRI for Backup and remote Support

Hello,
is it possible to configure an ISDN BRI
to use them for Backup and if no Backup is up (primary connection works)i can use
the ISDN BRI for Dialin (Remote Administration)?
My Backup Solution works fine but i do not know, how i have to configure the ISDN BRI so, that acceppt my ISDN Call for Remote Administration.
Thanks in advance
Lorenz

Hi
You can configure 2 dialer interfaces one for dial in and another one for the dial out purpose.
make the 2nd dialer interface as a backup interface for your primary interface and define the floating routes accordingly..
would suggest to go thru the following link which has the whole lot of possible config scenarios discussed and it may help u out in getting the things place ..
http://www.cisco.com/en/US/tech/tk801/tk133/tech_configuration_examples_list.html
regds

Connecting to an ISDN BRI on a router from a PSTN line from remote site..!!

Friends,
I have a 1812 at HO with WIC1 BS/T Card, connected it to an ISDN BRI line.One of my critical remote location uses Leased circuit to reach my HO Router.But in case if LL goes down,some of the important PC's at the remote site should be able to dial to HO Router BRI Number using PSTN line, get connected and continue, ip address assigned from HO Router and access the application... Is any way available...

Hi Arnab.
You need to configure dial backup through AUX port. You need to connect a normal PSTN line to a modem which in turn is connected to your AUX port. You will have to configure a chat script which you can find in the attachmnet. The attachment is a working example in one of my routers.
You also have to create an ASYNC interface. Check that in the attached file also
--Pls rate if useful---

I am looking for a good Call Blocking App for my iPhone 5...any suggestions??

I am in need of a good call blocking app for iPhone....please any suggestions will be greatly appreciated!

As Randy Landry1 says, Google for "silent ringtone", download and install on you iPhone as a ringtone.
Now create a contact for the offending phone number. Assign the contact to the silent ringtone and set no vibrate.
When that number calls it will not ring, nor vibrate. It will light up the screen, but if you do not see that, it will not bother you. They could leave voice mail, but that is easily deleted.
And if it is a situation where the are violating the do not call list, you can use the missed call log to report the number to the FTC.
Also, if the calls are abusive or threading, and the leave a voice mail, you something to show the police.

Why is Call Block not available?????

I've started getting these harrasing political phone calls from the same number. In the past,
I remember that I could use Call Block (*60) to block them. I now see that the feature is
"no longer available to new customers". So how do I keep these cretins from ringing my phone????
I subscribe to Freedom Essentials, so I have Caler ID, Forwarding, and Voice mail. I never noticed
that they don't mention Call Block now.

There's always the Do Not Call List but unfortunately politicians are exempt. Like how they write the laws to suit their needs????
You could check with your states public utilities commission or verizon to see why it is no longer being offered.

Call Blocking does not. Is this just a scam too?

Verizon call blocking is a useless 'service', dozens of calls come through with no phone number at all on the caller ID, something Verizon specifically states it will NOT DO. Any ideas?
Verizon call blocking does not address scammers and money-seekers who have caller ID of "Not-Available' -- honestly my dog could figure out how to block these but Verizon cannot. Besides paying more money to someone else, is there any hope for the people who expected the Verizon service would work?

Scam no. A service that needs to be update to the 21th Century, yes. Still based on early callerid tecnhnology which is easily bypassed by all those so called "telemarketers" . You should have now trouble with ligitimate callers, but lots of illegal calls come in.

Using *77 to set 'anonymous' or 'unknown' call blocking is not working

Per instructions from Verizon, I used *77 to turn on anonymous call blocking last night. I dialed *77, and got a voice telling me that I have enabled anonymous call blocking.
However, it's NOT working. When I call home from my office, it shows up in caller ID as "unavailable"; shouldn't a call that is identified as 'unavailable' be blocked with this service? Does anyone understand why this would be the case? Are all 'unavailable calls' the same?

Unavavailable/unknown calls and anonymous/private calls are two different things. Anonymous calls are calls from someone who has chosen to block their telephone number from being displayed on your caller ID screen. This means the caller has dialed *67 before dialing your phone number (or they have what is called line blocking where all their outgoing caller id info is automatically blocked without them having to dial *67 before every call). *77 is used to block anonymous/private calls and force the caller to allow their caller id info to come through to your phone in order for the call to complete.
Unavailable/unknown calls are calls in which no caller id information has been sent. These are generally from collection agencies or telemarketers. *77 will not block these calls in any way. The only services which will block or screen these calls are Call Intercept or Do Not Disturb.

HT204266 where can i get a call blocker app from?

Hi
I have been looking for an app which blocks calls . there are a few in the market but these are like really crap and they dont work. i dont want to have to resort to changing my number. my service provider is not able to block a number, the only way to do that is by going to the police. which i dont want to do , or change my number which i dnt want to do either.
please help! in desperate need of a good working call blocker!
thanks

Check out this link: http://store.apple.com/us/product/M9319G/A
I believe you are looking for a Mini-DVI adapter to a video or audio input.
Good luck

I've blocked a contact with ios7 using call blocking feature but it still manage to call through ... anyone has this similar problem?

yeah, i've set a number to be blocked using the ios7's call block feature 2 days ago. today, the phone rang and displayed the number which i've blocked ... anyone encountered this problem?

Same thing just happened to me. I've created a "Spam Call" contact and have been adding numbers to it as they come in. Today is the first time that the phone rang that was named Spam Call. Very disappointing.

ARE YOU USING DIGITONE CALL BLOCKER ?

Have Verizon Freedom Essentials
Verizon Call Assist works great on my Desktop
Would appreciate comments from anyone who is presently using
Digitone Call Blocker 10
What equipment do you use with it...Brand names?
Tom
Freedom Essentials, QIP 7100 1,Bose SOLO TV Sound System,,QIP 7216 P2,M1424WR Rev F, iPad 2 WiFi,iPhone 5,TV SYST INFO Release 1.9.5 Build No. 17.45
Data Object 39.45
Solved!
Go to Solution.

Great !
I've looked into it and it sure sounds terrific.
Please let me know what VZ phone service you have and what "equipment" it will be working with.
Thanks for your prompt response.
Happy Easter.
Tom
Tom
Freedom Essentials, QIP 7100 1,Bose SOLO TV Sound System,,QIP 7216 P2,M1424WR Rev F, iPad 2 WiFi,iPhone 5,TV SYST INFO Release 1.9.5 Build No. 17.45
Data Object 39.45

Call Blocking -- Why can't we do it?

The simple question is, "Why can't we have an app or option to block unwanted calls, without jailbreaking the device?"
Some of you are going to say, "You can through your carrier." This is only partially true.
Verizon allows you to block 5 (just 5) calls via their website. But why have to go to their website to do this? What if you have a company-paid line and don't have login access to their site? Why do you have to renew your blocked numbers every 90 days?
My Blackberry Storm had an app that simply intercepted the call and dropped it or directed it to VM, if I had put the number on my block list. Blocking the contact was a simple as selecting the number from the incoming call list and choosing, "Block this contact" from the menu.
This seems to be related to the lack of flexibility in how calls are received by each contact. There are no separate controls for volume and vibrate that can be set per contact. If there were you could turn off vibrate and silence the ringtone for contacts you didn't want to be disturbed by, at the very least.
Had I known this simple functionality was not available I would not have bought this phone.

Thanks for the replies.
roaminggnome: I know it's not a feature. I am lamenting that very fact. And, yes, it was a great feature of the Blackberry (and others). Why does Apple not allow it? There has to be some business reason because it should be easy enough to accomplish if apps could intercept a call before it alerted you.
I also know that true call blocking is a carrier-level function. Wouldn't it be great if you could block the number on your iPhone and the option was saved on Verizon's server? Why not? Aren't smart phones supposed to be smart? I can easily block calls on my home phone through AT&T's U-Verse service.
Instead you have to jump through hoops to create a silent ringtone (or buy one). You have limited SMS tones to choose from and people talk about jailbreaking their phone just to add more. This was all easy and free on the Blackberry.
The Google Voice idea would be great if my true cell number weren't already out there. I really don't want to have to change numbers and have to redistribute it to all who should have it.
I really thought the iPhone would be like the Mac, with lots of cool options and functionality. I've had Macs since 1984. I may have been mistaken.

ISDN BRI Call Blocked

Similar Messages

Maybe you are looking for