Issue in stock category

hi,
  i am posting gr.po in migo for x- material as 10 quantity then TR is created automatically with stock category as "Q" after quality inspection once i put TO for that material the stock category as "Q" not as available stock . my requirement is whenever goods came it moved to qc then only it moved to warehouse. how to achive this flow.......because once i put gr the transfer requirement is created with stock category as "Q'. so if i proceed  this TO created with Q category.
thanks
muthuraman.D

hi,
  as per suggestion first one  soution i go for manual TR its working fine but one more issue arises. when i post gr/po in migo the stock  get increased in warehouse as stock category as 'q' with +ve quantity and _ve quantity looking for posting change TO and then i put manual TR -TO-confirmation  for purchase order stock moved destination bin  with stock category as unrestricted stock,but my problem is  stock in posting change quantity still there.
my requirment is once i post gr the stock never get updated in wm level. once i put manual tr-to  then only it should updated.....other wise two stock are updated one for manual TR and another for migo posting(waiting for posting change in interim area  with -ve and +ve quantity values)....how to avoid that....kindly explain..........
Thanks
Muthuraman.D

Similar Messages

  • Batch / Stock Category Issue

    Dear All,
    I have a scenario where a single material in a purchase order has different stock categories as below:
    PO/LI - 10    Mat A    US
                20   Mat A    FR
                30   Mat A    AG
    When the GRN is done, ideally for the different stock categories the created system batch should be different, but in my system a single batch gets created for all the stock categories. As per my understanding the relationship between Batch & Stock Category is ONE to ONE. But how could it is be possible that the system replicates the same batch for the different stock categories for a given GRN instance ( in a single material document)
    In the material master, the discrete batch is maintained and also the batch management tick is maintained.
    Any reasons as to why this is happenning and how i could rectify this
    Regards
    Shabeen Buhary

    What "stock category" means? "US", "FR", "AG"?
    Are you speaking about valuation types?
    How batch number ssignment is set in the system? Please check it - maybe user exit SAPLV01Z  is used --> revise the logic of it with the help of an ABAPer.
    In your example I can see separate line items - you should be able to set the system to assign different batch numbers to the items (via user exit).
    Regards,
    Csaba

  • 2LIS_03_UM Datasource Material  belonging to Stock Category 'E' Issue.

    Hi,
    We wanted to use 2LIS_03_UM Datasource  for Sales order Stock Valuation as we want these valuations in Daily level at sales order item level .  But we are having a problem in Extracting  Materials with Stock Category(BSTTYP) 'E'.  I have selected fileds  LBWE MBLNR, KDAUF, KDPOS from LBWE pool and brought them to the Extractor .  After filling the setup table in OLIZBW with the Company code and posting date. In RSA 3 i am getting data for the company code and posting date. But the Fields BSTAUS and BSTTYP with values 'V" or null.   I just came across in one of the forums we have to do some config in
    include LMCB1F20 (routine STA_VERAENDERUNG).
    And joins on tables MSEG, T156C, T156M
    cosidering fields ->
    BUSTM, ZUSTD, CNT02, LBBSA, SOBKZ
    Can i have some more details on how to do this in R/3.
    Thanks

    Hi Arun,
    Valuated Stock with unrestricted use is a Non - Cumulative key figure and you dont have to add this field to this data source or for that matter to any data source. You can simply include this info object directly in the Inventory Cube and write the Update routine accordingly.
    Before writing the routine you must ask your finctional guys to provide you with the classification of the material movements. I mean are there any Z Movements for this key figure? What are the process keys for this? etc...
    This will help you in writing the routine for this key figure.
    Hope it helps...

  • Cross Docking for stock category Q (inspection stock)

    Hello everyone,
    My client uses cross docking in 4.7 release and recently a requirement came up where they wanna be able to cross dock stock received from production while the User Decision from QM is still pending.
    I have tried to walkthrough the code behind planned/opp cross docking and realised that only available stock is taken into consideration.
    I d be really grateful if anyone could suggest how to best approach and tackle this issue? Please consider that the quant should not lose the inspection lot number so that once UD is given, the stock category changes automatically.
    Thank you
    Kind Regards

    Yes it is possible. In the IM/WM interface tables, in the second table, you can vary the process according to stock status. See the third column.
    LogisticsExecution \ Warehouse Management \ Interfaces \ Inventory Management \ Define Movement Type
    Following is the config. help text for the field
    Special Stock Indicators for Whse Mgmt
    Use
    In the Materials Management system you can post different transactions using one movement type.  For example, posting goods receipt to unallocated stock or goods receipt to
    stock in quality inspection.
    These transactions are treated differently by the system on the basis of this indicator.  Together with other indicators of a movement type in the Materials Management system, this indicator is used to correctly allocate a movement type in the Warehouse Management system so that the transaction can be posted accordingly.
    Regards,
    Nick

  • 2LI_03_BF Material Stock Type and Stock Category Determination

    Hi All,
    I need your help in determining the stock type and stock category of a certain material.
    Is there a way to determine it manually? cause i tried to look at the MSEG table and it does not show anything but when i try to run the material document that contains the movement/material it populates the stock type and stock catertory in the setup tables.
    Regards,
    Alden

    Hello
    1) 2LIS_03_BF clearly gives you the receiving plant and the issuing plant. For eg if you are doing plant to plant transfer there will be 2 entries in 2lis_03_bf , one for issue and one for receiving. You can bifurcate the receiving plant and the issuing plant by using either process key (BWVORG ) or debit credt (SHKZG)  (H stands for issue & S stands for receipt).
    2) 0MAT_PLANT_ATTR  provides you the plantwise specila procurement type
    3)  you will get  VBUK-GBSTK in the standard source 2LIS_11_VASTH . You will have to combine the data at the BW level
    Regards
    Gajesh

  • Additional Stock Category Considered in SNP Heuristics

    Hi,
    The customer has a requirement to add 'inspection stock' into the SNP Heusrics planning considerations. The stock is already CIF'ed to APO, and is already seen in RRP3 Product view.. So I think part of the work is done. What further do I need to do to get it added to the key figure in the SNP Planning book?
    I have looked at MSDP_ADMIN and the details of the key figure, The stock key figure used here is listed in many planning obj structure, eg 9AMALO, 9ASNPBAS etc. But in all of them there are no category groups or individual category settings assigned... and it is actually greyed out and I cannot add one. So im not sure what it is working on today, even before the new customer requirement.
    Is stock as a key figure different than others? I understand category groups and how they are used in ATP Issues / Reciepts for deployment.. but this appears to be a different setup? (as it is blank currently)
    Other posts seem to have menitoned something about the SNP tab of the location master data in APO. 'Category Groups for Stocks'.
    Do I need to create a new category group in SPRO customising, and then add it to this location master data? or the key figure? or both? or none?
    Please help.
    S SB

    Answering my own question now I have found the answer for the benefit of others:
    When a specific stock category group is assigned in the location master then the sytem considers all the stock categories assigned to that category group while calculating the initial stock.
    If no stock category group is assigned in location master then the system looks at the category group "ST1 - Opening stock" in SPRO and considers all categories in cat group ST1 while calculating the initial stock.
    So to include CF / CI / any other cateogy in the initial stock calculation , all you have to do is assign those categories to ST1 category group . Once this is done you will be able to see the difference in your initial stock.
    There is NOTHING required in MSDP_ADMIN. Tested and confirmed.

  • Issue in Stock transfer

    Hi
    We have an issue in Stock Transfer. the Stock transfer happens between a manufacturing plant which is excise registered and a depot, which is not excise registered. We raise a Stock Transfer order from the depot on manufacturing plant with a freight component. The system creates a freight provision in the depot, when the goods issue is done by the manufacturing plant against the stock Transfer Order. After the goods issue the material is shown in Transit in report MB5T until the same is recieved by the depot. However, some goods are lost in transit and the same is recovered from the freight vendor. In such a case, we do a MIGO for the actual quantity recieved at depot and pass a debit note to vendor by loading the difference to material.
    The issue is:
    1. the quantity and the value of the physical inventory recieved have been rectified by a recovery from the vendor.
    2. However, how can we remove the goods, which we have short recieved from the report MB5T
    The certain work around  we have thought could be :
    1.  Receive the quantity in full at the recieveing Depot and then scrap the material to the extent it has been received short through M Type 551. However, the issue arises in case of transfer of goods from one manufacturing plant to another, where in both are excise registered. In such a case, goods receipt in full would not be correct as it would raise issues in excise registers.
    Please suggest
    Regards
    Sanil K Bhandari

    Hi,
    One suggestion is you can pass a document through MB1A for material loss in transit for the mateial lost.
    Followign accounting Entry would be hit :
    Transporter shrinkage Clearing Dr
    to Inventory Raw Mateial          Cr
    You can pass the same document through Mvt. Type 951 (GI Lost in Transit).
    Thanks & Regards,
    Taral Patel

  • Inventory report for stock category B

    Hi everyone,
    We are trying to generate a customer stock inventory report with stock category B. The table MARD is not displaying any values annwe also looked at table MKOL. Its not giving us any. How do i get the inventory report for this stock type B. Kindly Advise.

    it is customer owned stock. We receiver materials from customer for repair and we recondition them and we give it back. for this we maintain it in stock type B. it is specifically used in aerospace industries. We want to make an inventory report for this customer owned stock in our inventory . i am unable to get the table. Kindly advise

  • Restrict goods issue if stock on posting date is zero

    Requirement:
    Current Inventory period : July 2011
    Stock of a material from 01.07.2011 to 30.07.2011 is zero(in MB5B report)
    I upload stock of material  or GRN occur on 31.07.2011. Say Quantity u2013 100
    Now stock as on 31.07.2011 is 100 in MB5B
    Still, Stock of a material from 01.07.2011 to 30.07.2011 is zero(in MB5B)
    Now, If I do goods issue of a material quantity 100 on 15.07.2011. System allows goods issue. though opening and closing stock as on 15.07.2011 is zero.
    After goods issue transaction if I check stock of material on any date between 16.07.2011 to 30.07.2011 , The opening stock and closing stock shows negative.
    I want to restrict goods issue if stock on posting date is zero or less then stock available on posting date.
    Please suggest

    Hi,
    This is not the way SAP is designed. As the previous speakers wrote (and as you noticed yourself), SAP maintains stock figures in the database per month rather than per day. MB5B makes complex calculations in order to find out how much stock you had on a specific date - as you probably noticed on the response time. Performing such calculations every time you do a GI would be unfeasibly heavy task for the system - remember there are organisations that perform hundreds of inventory movements a minute!
    An alternative solution I suppose would be to maintain the daily stock figures in the database. This would make the finding of the stock figure very quick, but on the other hand, the maintenance of such table would be unfeasible - if you post today a GI on say July 1st, you would need to calculate 36 stock figures and update 36 database records!
    Hope this explains the technical issue.
    BR
    Raf

  • Issue with stock qty of component in Structured Articles in SAP BI

    Dear Experts,
    We are extracting stock in BI through SAP standard data source. We have used 2lis_03_bx and 2lis_03_bf data sources. We are facing issue with stock data validation due to structure articles (pre-pack) available in SAP source system.
    We have stock of structure articles available at DC in source system.  When we extract this information in BI, this article gets split into its components automatically. Due to which stock of components articles gets increased with huge amounts.
    To analysis it in further detail, we have created below scenario:
    Article Document Number:  4900000827
    Article Number (Pre-pack):  300000082901
    Article Number (Component): 300000082002
    Stock of pre- pack article at this article document number: 174 pc
    Stock of component article at this article document number: 348 pc (due to splitting of pre-pack article) + 151 (its own stock movement). Total stock for this article is 499. But actually total stock for this article should be 151 only.
    As per our Business requirement, pre-pack article should not be split into its components. And stock in BI should be totally in sync with SAP stock.
    I kindly request you to suggest the solution to rectify the same.
    Thanks in advance.
    --Vikas

    Hi Vikas,
    Check the OSS note L 1320386 - Frequently asked questions regarding BW Trade Foundation too.
    Regards,
    Rajesh

  • Made a UD to 'Scrap'. But Stock Category is "Q" and does not show in MMBE "Blocked"..WHY?

    Hi,
    I made a UD of an Insp Lot to 'Scrap' in the Inspection lot stock tab.
    The system automatically created a material document with movement type 553 (Direction -) and 551 (Direction +)
    However the stock Category in the material document is "Q". IS THIS CORRECT? SHOULD THIS BE "S" (This is in the WM tab of the material document).
    Also when I query MMBE after the above UD to Scrap, the batch quantity is not shown either in Quality or Blocked stock. IS THIS CORRECT?
    Please advise.
    Regards
    Priyanka

    My understanding was when I input a quantity in 'Scrap' field during UD
    1) The stock should be blocked (hence it will show under blocked stock column in MMBE)
    2) The stock category should be "S" and not "Q"
    I agree that in MMBE based on your explanation the stock should not be shown in blocked.
    But can you explain why the stock category is "Q" instead of "S"
    Regards
    Priyanka

  • Create Stock Category

    How can I create a new stock category?
    Right now we have 4 separate categories....
    1 - First
    2 - Second
    C - Closeouts
    S - Samples
    Where in SAP can I create a NEW category?  (example: "3 - Third")

    Yes I have, I've created multiple characteristics using the "Chars Group" "AFS characteristics for categories" under the Basic Data section of the Basic Data tab.
    Unfortunately, none of them show up under Category Structures or Coverage Strategies in SPRO.
    How exactly do I edit the settings of a coverage strategy in SPRO?  There does not appear to be any options availbale when a coverage strategy is selected.  Is this something that is taken care of under CT04?  Or am I not understanding how a coverage strategy works?  What is the difference between a Characteristic and a Catagory Structure and how can I edit or change the settings of a catagory structure?
    Edited by: Cameron on Dec 3, 2009 9:51 AM
    Edited by: Cameron on Dec 3, 2009 10:14 AM

  • Valuated issued value Stock

    Valuated issued value Stock
    I want to check the values of BW & r/3 are matching for KF  Valuated issued value Stock in which t-c0de can i check it
    I am checking valuated stock value in mc.5
    & valuated stock received value in  table s031
    these values are matching but when I check  Valuated issued value Stock in mc.6 some of the values ar ematching & some are not matching

    Hello Maya,
      Use transaction MB5B  where you can select stock by date.Also select Valuated stock. This should match the  your KFs in BW,
    Um is needed to get correct value of the stock
    If the material cost is adjusted in R/3 then revaluation entries are posted in R/3. The UM datasource picks up these revaluation entries.
    Jaya

  • Re-configure 'Stock Category' in the Warehouse Management system

    Hi Gurus,
    As we all know, it is possible to see which batch/material is in blocked status because the system highlights it with stock category indicator "<b>S</b>". With this, I would just like to know if it is feasible to modify the configuration in the system so that it assigns the Stock Category (labelled as '<i>C</i>' in transaction LS26) as follows:
            <b>S</b> : blocked without a usage decision
            <b>R</b> : batches which are blocked because they were rejected (there was actually a usage decision)
    Please let me know your thoughts regarding this matter.
    Hope you can help me on this one. Thanks in advance.

    Hello Francis,
    I think it is not good idea to change the standard SAP settings becuase we are not sure where our changes will impact. However, the SAP system is behaving in the same way you want, the only thing is you need to do relevent transaction at inventory level and subsequently carry out posting change in Warehouse System.
    Quality stock with stock indiacator 'Q'
    Blocked stock with Stock indicator 'S'
    Return stock with stock indicator 'R'
    Hope this helps.
    Arif Mansuri
    Reward if answer is helpful.

  • Issuing consignment stock for sub contracting against outbound delivery wm

    HI
    I have a outbound delivery created against subcontracting PO for issuing the components, i have stock determination turned ON so during picking against the outbound delivery i am able to pick K stock and own stock too(based on availability) but when i do PGI i get an error message You have not entered a value in field "Owner of stock" although an entry in this field is mandatory. message M7018, please share your thoughts whether is it possible to issue K stock for subcontracting PO if so how it can be achieved
    Thanks
    Terry

    Consignment Stock is not valuated stock of the system. Issuing a Material from K stock to Subcon means, you need to pay to vendor for the material through MRKO settlement.
    This message is because of the reason for MRKO. System should be updated with " whose stock are you using"
    Please enter the vendor number on that field, depend on which MRKO is done.
    Raghavan

Maybe you are looking for