JCA Binding Component connection issue - Help plz

All,
soa - 11.1.1.3
I configured a async BPEL which reads data from DB (using DBAdapter) and write to a file. I'm getting the following error frequently. But same BPEL if I test it after few minutes it works, its very intermittent. Any clue?
I checked the DB which is installed locally, its up and running. No issue i seen in the DB.
Caused by: BINDING.JCA-12511
JCA Binding Component connection issue.
JCA Binding Component is unable to create an outbound JCA (CCI) connection.
*OutOrderRequestMap:TerritoryPull [ TerritoryPull_ptt::TerritoryPull(TerritoryPullInput_msg,TerritoryPullOutputCollection) ] : The JCA Binding Component was unable to establish an outbound JCA CCI connection due to the following issue: javax.resource.spi.IllegalStateException: [Connector:199176]Unable to execute allocateConnection(...) on ConnectionManager. A stale Connection Factory or Connection Handle may be used. The connection pool associated with it has already been destroyed. Try to re-lookup Connection Factory eis/DB/orafin11i from JNDI and get a new Connection Handle.*
Thanks,
sen

Are you using JDBC Xa datasource ? Try following the steps defined in this forum link @ Re: Error at the time of Invocation of DB Adapter

Similar Messages

JCA Binding Component connection issue in the Oracle Order Demo Application

Hi,
I setup the Oracle Fusion Middleware. I also deployed the Oracle Fusion Order Demo Application in the soa_server. I placed the order in the store front web.I initiated the webservice (OrderBookingService) and found the below error in the soa_server_diagnostic log file.
=====================================================================================================================================
Caused by: BINDING.JCA-12563
Exception occured when binding was invoked.
Exception occured during invocation of JCA binding: "JCA Binding execute of Reference operation 'Write' failed due to: JCA Binding Component connection issue.
JCA Binding Component is unable to create an outbound JCA (CCI) connection.
OrderBookingComposite:USPSShipment [ Write_ptt::Write(body) ] : The JCA Binding Component was unable to establish an outbound JCA CCI connection due to the following issue: BINDING.JCA-12510
JCA Resource Adapter location error.
Unable to locate the JCA Resource Adapter via .jca binding file element <connection-factory/>
The JCA Binding Component is unable to startup the Resource Adapter specified in the <connection-factory/> element: location='eis/file/FODFileAdapter'.
The reason for this is most likely that either
1) the Resource Adapters RAR file has not been deployed successfully to the WebLogic Application server or
2) the '<jndi-name>' element in weblogic-ra.xml has not been set to eis/file/FODFileAdapter. In the last case you will have to add a new WebLogic JCA connection factory (deploy a RAR).
Please correct this and then restart the Application Server
The invoked JCA adapter raised a resource exception.
=====================================================================================================================================

Thanks Guys.
I resolved the issue.
The issue is that FileAdapter for FulFillment mediator is missing.
Solution 1:
File adapter connection factory needs to be created via the weblogic console
The details below:
     JNDI Name: eis/file/FODFileAdapter
     controlDir          java.lang.String     /tmp/control
     inboundDataSource     java.lang.String     jdbc/SOADataSource
     outboundDataSource     java.lang.String     jdbc/SOADataSource
     outboundDataSourceLocal     java.lang.String     jdbc/SOALocalTxDataSource
     outboundLockTypeForWritejava.lang.String     oracle
Solution 2:
seedFodFileAdapterResources target in $FOD_HOME/bin/common-sca-tools.xml needs to be executed to create the file adaptor.
Thanks.
Ilayaraja

HT4623 recent ios6 ipad wireless connection issues-help

?

iOS 6 Wifi Problems/Fixes
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Connection issue help

I have intermittent connection issues. I have been calling and calling..... We did finally get someone who spoke English. A "technician" came to the house and found nothing wrong with the connections, other than to tell me that in our apartment we have copper wiring and that there is nothing that they can do. Although, my neighbor, who has Charter, has never had an issue.
I overlooked the fact that the "technician" that I'm paying the service for, only glanced at my computer and told me that there was nothing wrong. Now I still left with a connection that constantly drops, is still an issue.
I called again, only to reach someone I can barely understand, who tells me to disconnect the connection that goes from the modem to the computer and switch them. Uhm, okay. Just for fun, i switched the cords (spun em around) . I asked what purpose this would serve as I'm using the same cable? Obviously, this did not change anything.
I have called several times and am left on hold.
I called once again to inquire why my Verizon in Home Agent would not connect to the internet. Although, I did have internet service. The agent said that the In Home Agent would come on only if I had a connection issue...This makes absolutely no sense.
Lastly, after being so frustrated, I managed to spill a drink (fortunately, I had not yet reached for the bottle of liquor). This brings us to a new dilemma, the computer now does not turn on. (using the laptop)... I have the insurance for a replacement/repair of my computer. I again called Verizon, no one has heard of this service, but yet I pay a monthly fee. "It's not something they handle" but they are willing to TRANSFER me AGAIN.
{edited for privacy}

This is DSL-101 - but make sure your phone cord is no longer than 12 feet long ... and not one of those cheap "ribbon" phones cords. It's not the ability of the signal to reach the modem - rather the ability of your modem to transmit through the length of the phone cord. (You would be amazed how many people how 50' phones cords going to their modems). The shorter the phone cord, the better.

Ubuntu issues help plz!!!!!!!!!

i have a hp pavilion dv7 with ubuntu and it turned off i switched it back on and now its just a grey/black screen and wont let me do anything i need some help plz thnx
B/@$3

KNRK wrote:
It looks like you are facing lot of difficulties in finding the Operating System Image for your Notebook
I understand how it feels, We will surely assist you with this
Please reply to this Post with full Model and Product Number of your Notebook and the full version of the Operating
System you are currently running
Please revert for immediate assistance
Regards,
K N R K
B/@$3

Officejet Pro 8600 Plus connection issue - HELP!

I have a strange issue: after some hours, the communication link is dropped between the computer and printer. When this happens, IE becomes unusable and will not connect to anything. This is replicated on three XP home machines. The fourth, a vista ultimate machine, does not seem to be affected (yet). I get the "scan to computer is disabled" error. It cannot be re-enabled. At this point I cannot print either. I can reach the embedded web server on the printer via firefox and can still surf using firefox. I can ping the printer, but again once the connection is dropped, no printing or scanning to the computer. The only thing I've found that resolves the issue (temporarily) is to reboot the computer, which just starts the cycle again.
last night I installed the software on an XP machine and the laptop to test when the connection dropped. They lasted from 7pm Monday until I got home at 5pm Tues. The machines were not used. Once I started using them (firefox only), then they dropped the connection within a half hour of each other around 7pm. The other XP machine lasted from 7pm Mon until 7am tues, when my wife started using it and then noticed it dropped sometime that tues between 7 and 9AM. An 11am tues reboot ran OK until 10 pm tues when connection was lost again (and IE is now dead). The Vista machine has been running since 7pm monday until now (930pm tues) and still seems to be holding.
printer hardwired, to router, static IP, 100-full link speed (also tried 10-half)
router dlink di-655
two XP machines are hardwired, vista is hardwired, and last xp machine is a laptop on wireless.
I've swapped cables rebooted and reinstalled multiple times. I must have a file a mile long on the support phone line. They were unable to fix it. I asked this to be escalated, but who knows when I'll get a response.
I've toggled firewalls - XP built in
I've uninstalled anti virus software
I've even put up with crazy suggestions from tech support like changing the router channel (uhh, it is wired!)
one xp machine had an AIO 4215 hooked via USB and the others printed to it via network, but the printer has been deleted from the networked machines.
I can ping 127.0.0.1 which is supposed to indicate the tcp service is OK.
I have not reset winsock .. I can see one machine being bad, but three????
malware / virus scan shows no issues. Again one maybe, but three??
The only thing I can think of is that there is something in the XP networking stack that conflicts with the new 8600 software as hours pass. Perhaps there is some polling operation that goes on then dies after some time, then it kills IE as it dies.
When the printer works it is great, but rebooting is not a permanent solution to this.
any suggestions would be greatly appreciated!!!!!! I am stumped and so is tech support. They are sending it to engineering, but who knows when they will respond.
thanks in advance.
This question was solved.
View Solution.

well it looks like I have a working solution ... I downloaded a freeware file called process.exe . I made a cmd file via notepad with the following contents:
rem this is to keep the HP network printer communicating with the desktops
rem
process -k "hpnetworkcommunicator.exe"
rem
process -k "scantopcactivationapp.exe"
rem
"C:\Program Files\HP\HP Officejet Pro 8600\Bin\HPNetworkcommunicator.exe"
rem
Start "" "C:\Program Files\HP\HP Officejet Pro 8600\Bin\ScanToPCActivationApp.exe" -deviceID CNXXXX:NW -scfn "HP Officejet Pro 8600 (Network)"
the XXXX is your printer serial number with an extra character or two. Pull that number from the port tab after you pull up "properties" for the 8600 printer.
This cmd file basically restarts the printer link. It opens a command window that launches the program to re-establish the link.. then it closes the command window. The launched program shows that the communication link is dead (just for a few seconds), but then it makes the connection... THEN you hit the close button and coninue your work until it dies again.
I may have it autorun every X hours if I can narrow down a good time. Until then I have a shortcut on the desktop to "FIX HP LINK" ... I only had to do this for my XP machines, as the vista one seemed OK.
What ticks me off is that I shouldn't have to do all of this diagnosis. It would be nice if there is a fix in the pipeline so the link stays stable al the time. I've spent hours trying to figure this crap out.
Anyhow, I hope the time I spent helps someone. PS, thanks to the OJ6500 thread that had the info for the scantopcactivationapp.exe program.
PS ... I'm still waiting for an engineer to contact me, if any HP employees are reading this.
PSS I haven't tried this without killing and restarting the hpnetworkcommunicator stuff, but it works for now.

RADIUS \ NPS - Connection Issues - Help greatly appreciated.

Hello,
I have been banging my head on this issue, and would greatly appreciate some assistance getting this worked out. My goal here is to authenticate both domain & non-domain devices (laptops, smart phones, tablets, etc) to my network. I'll followed
several tutorials without much luck - and I feel my lack of knowledge on this particular topic weighing on me.
I am currently working in a lab environment, which consists of a Server 2012 VM with Active Directory installed and configure. I've also setup and configured my Wireless Access Point, which i've confirmed works just fine using WPA-Personal. I've
installed NPS, as well as AD CS using all of the defaults.
I'd like to know the opinions of anyone here as to the best way to set up this environment for my needs. As mentioned above, I want to be authenticating both Domain and non-domain devices. Should I have to be setting up certificates of some sort
for this goal? Or can I stick with just plain AD user/pw access?
I've configured my WAP for WPA-Enterprise, specified the RADIUS server IP, and entered the shared secret. I've configured NPS w/ my RADIUS client (that being my WAP). My Wireless Policy consists of the following:
Overview:
Policy Enabled
Grant Access
Ignore User account dial-in properties checked.
Type of network access server: Unspecified.
Conditions:
NAS Port Type - Wireless - Other OR wireless - IEEE 802.11
Windows Group - DomainName\Wireless Users (I created the Wireless Users security group and added one newly created user to the group)
Constraints:
EAP Types: Microsoft: Secured Password (EAP-MSCHAP v2)
Less Secure Auth. methods selected: MS-CHAP-V2, MS-CHAP
Everything else in the network policy is set as its default, and i've registered the NPS server in AD.
My attempts to connect fail, and the only relevant Event Log that is being processed is in the Network Policy and Server Log is what i've copied below. Please ask for any information that may help me work this out, i'm all ears!
Thank you.
Network Policy Server denied access to a user.
Contact the Network Policy Server administrator for more information.
User:
Security ID: Domain\Daniel
Account Name: Domain\Daniel
Account Domain:
Domain
Fully Qualified Account Name:
Domain\Daniel
Client Machine:
Security ID: NULL SID
Account Name: -
Fully Qualified Account Name:
OS-Version: -
Called Station Identifier:
2A-A4-3C-99-FE-CA:DomainWIFI
Calling Station Identifier:
00-24-D6-A4-C8-8A
NAS:
NAS IPv4 Address:
192.168.1.100
NAS IPv6 Address:
NAS Identifier:
24a43c98feca
NAS Port-Type:
Wireless - IEEE 802.11
NAS Port: 0
RADIUS Client:
Client Friendly Name:
UniFi
Client IP Address:
192.168.1.100
Authentication Details:
Connection Request Policy Name:
Wireless Policy
Network Policy Name:
Wireless Policy
Authentication Provider:
Windows
Authentication Server:
WIN-PBL42GEIH4E.Domain.local
Authentication Type:
EAP
EAP Type: -
Account Session Identifier:
Logging Results:
Accounting information was written to the local log file.
Reason Code: 22
Reason: The client could not be authenticated because the Extensible Authentication Protocol (EAP) Type cannot be processed by the server.

Hi,
You receive this message when there is an incompatibility in authentication between the client and server.
Check the authentication protocol on the client and verify if its the same as the authentication protocol configured in your network policy.
Besides, secure password EAP-MS-CHAP v2 is an EAP type that can be used with PEAP, for password-based network authentication. EAP-MsCHAPv2 can also be used as a standalone method for VPN, but only as a PEAP inner method for wireless.
For detailed information about EAP-MSCHAPv2, please view the link below,
http://technet.microsoft.com/en-us/library/hh945104.aspx#BKMK_LAN_SecPWD
Therefore, we recommend that you need to change your authentication method on both of server and client.
Moreover, if you change the authentication method to PEAP, you need to implement ADCS in your environment.
Hope this helps.
Steven Lee
TechNet Community Support

Wi-Fi Connections issues: HELP NEEDED!

I've been running my iPhone mostly on the EDGE network the past few weeks. Some hair might have gone grey while I was waiting for it to laod, but it loaded after sometime.
Anyways, I have a linksys wireless router and everytime I try and use my Wi-Fi with the iPhone it says "Safari can't open the page because it could not connect to the server."
Does anyone have a solution for me to change settings through network settings, or anything eles that might be quick and easy?

Here is a quick check list you can take a look at and try. As well as a couple questions. It sounds like possible interference of some kind.
1. Has Firmware on the router been updated?
2. Have you updated iPhone Software to 1.0.1?
3. Have you done a restore on the iPhone and tested the network again?
4. You may wish to inquire to your router provider about changing the channel on your router, To see if it is stopping the iPhone from grabbing a stable connection.
Test your iPhone on another Wireless Network, If other Wireless Networks work, Then it could just be a compatibility issue with your router, But please inquire to your Router Provider about how your wireless device will not hold the information of the Router IP and other information, They may be able to change a setting in the router to help stabilize the connection.
Apple has also released a new router, The Airport Extreme 802.11n
http://store.apple.com/1-800-MY-APPLE/WebObjects/AppleStore.woa/wa/RSLID?mco=E84 08794&nplm=MB053LL/A

Airport Extreme / Apple TV Connectivity issue -HELP!!

I am able to enter my WEP password on the Apple TV, and it connects to my wireless network. But, the next day, it doesn't show up in my list of devices on iTunes. I look at the setings on the apple TV, and it says I am not connected to network, and I have to enter password again. What setting do I need to adjust on the Airport Extreme or the Apple TV?

I have the same issue. Wish I could help.... It is ridiculously annoying to have to put in the password every day, yet it is all I can do!
I dont understand... even if it drops the connection to the TC, why cant it reconnect on its own like computers do?

Speed connections Issues Help?

Hi,
New to the forum and looking to receive any help with my problem.
Background Info:
I was on sky broadband and receiving a steady 4mbs D/L (Up to MB +Unlimited Broadband) at £12 per month.
A BT Representative cold called me and persuaded me to switch the broadband to BT (Already have the Phone with BT).
I was informed that i would get at least MB d/l and up to MB - so signed for the option 1.
Then I realized that my household is a heavy user,so changed the package to option 3 (Unlimited Broadband Usage)
costing me an instant £21.80 bill for adjustments.Fair enough.
The Problem:
After the 10 day period I am only getting 2.MB D/l at best.
I have been on the phone with BTU+their team of specialists and have still not resolved the issues as of yet.
I have to call back on Saturday after leaving the router on for a further 48 hours without powering down.
So Basically:
Paying twice as much for only half of what i was getting with sky?
If I could cancel the lot and switch back to sky .I would!
Rant Over (for now)
Thanks
Paul
Solved!
Go to Solution.

welcome to the forum
in order for the forum members to help please can you post the adsl stats from your router may need to 'show detail' to get all stats (if hub enter 192.168.1.254 in your browser and navigate to adsl or use a-z, if netgear enter 192.168.0.1) and run btspeedtester (MAC users may have problems) http://speedtester.bt.com or http://bt.custhelp.com/app/answers/detail/a_id/9354/c/346,4740,5520 and post the results .
are you connected directly to the NTE5 master or test socket or to somewhere else? Do you have any phone extension sockets in your home?
Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
Someone may then be able to offer help/assistance/suggestions to your problem
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

BG image issues, help plz

I am using Macromedia DW MX. I am having some issues with the
background tiling and not centering behind the nav buttons. If you
look behind the top row of nav buttons you can see the BG issue.
The problem is bad with IE but worse with Firefox. Anyone have a
fix for both?
Thx
Anyone help? [email protected]
http://www.huntbackcountry.com/backpacks.htm

This is the background image:
http://www.huntbackcountry.com/PixForWeb/MtnHeader1top.gif
doesn't appear to be tiling to me. The widith is 700px as
wide as your
table.
What exactly are you trying to achieve?
Nadia
Adobe� Community Expert : Dreamweaver
http://www.csstemplates.com.au
- CSS Templates | Free Templates
http://www.perrelink.com.au
- Web Dev
http://www.DreamweaverResources.com
- Dropdown Menu Templates|Tutorials
http://www.adobe.com/devnet/dreamweaver/css.html
"Wayne Newell" <[email protected]> wrote in
message
news:e8737p$e5o$[email protected]..
>I am using Macromedia DW MX. I am having some issues with
the background
>tiling
> and not centering behind the nav buttons. If you look
behind the top row
> of nav
> buttons you can see the BG issue.
> Thx
>
> Anyone help? [email protected]
>
>
http://www.huntbackcountry.com/backpacks.htm
>

WRT54G Version 3.1 Connection Issues - Help Please

Good Morning,
We have a WRT54G Version 3.1. Our existing network is wired and functions fine, I am adding the WRT54G for a few wireless clients.
During testing I have connected the wireless to my computer via CAT5 cable to port 1. I have connected another CAT5 cable to the internet port of the router from a known good wall jack.
When I first open the default address 192.168.1.1 and enter the password, all seems well. Due to having servers that hand out IP addresses, I disable the routers DHCP capability.
I enter the following information for example:
Local IP: 81.0.0.90
Gateway: 81.0.0.1
Subnet: 255.255.255.0
DHCP disabled
etc.
After changing the the local IP and receiving a confirmation that my changes were saved and I will be going back to the previous page, the page won't display with the address changed to 81.0.0.90 and it is blank.
I release my IP address through cmd, clear my dns cache and reboot the computer. After restart, I am presented with the stock MS address of 169.254.X.X.
I cannot connect to the local IP I established at 81.0.0.90 and nothing appears to work. The only thing I can do is reset the router and start from scratch...again.
Any ideas on what keeps happening and how it can be resolved once and for all?
Thanks in advance
Message Edited by T1Tech on 10-23-200603:49 PM

even if you have two DHCP enabled on both routers in your network, you will not get an IP adress conflict (exception of course if you're cascading two wireless routers).
a LAN port (ethernet router) to WAN port (wireless router) connection can be established allowing you to have both DHCP server enabled on your routers.
by doing the LAN to WAN connection, you will have two networks in a network.. both network won't meet cuz they will have different IP adress... router 1: could be 81.0.0.90, then router 2 could be 81.0.0.91.
if you want your two routers to meet and be in the network together, you just need to follow QUAK's suggestion to assign a static IP adress on your PC. or better yet, you can just connect the router you're disabling the DHCP server with to it's LAN port from a LAN port as well of your DHCP server (router 1). this is a LAN to LAN connection... by doing that, you will be able to open up the interface of your router 2(DHCP disabled) since your PC connected to it will get an IP adress...
"a helping hand in a community makes the world a universe"

Cannot connect ! help plz!

My family has the WRT54G2 V1 router. They dont know the wep(think thats what its called) password, so I decided to go to the linksys support site, and followed the steps to reset back to factory settings. I did that, and created a new password, and now i cannot get online at all!. Something is wrong somewhere. I can only get only connected with the cord. The reason why, i needed the password is because i just bout a net book, and wanted to connected. Now, all computers are screwed up thanks to me. someone help. lol

1) Please state your ISP
2) Please state the make and exact model number of your modem (not the WRT54G2).
3) Please do the following test:
Power down your entire network. Using an ethernet cable, connect your modem directly to your computer. (Do not use the WRT54G2 for this test.) Power up the modem and computer. Verify that you have a working Internet connection, then proceed with the following: (Even if your Internet connection does not work, state this, and proceed.)
Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig /all" (with no quotes), then hit the Enter key. Copy all the results to your next post. To do the copy, highlight the results, then use the copy (Ctrl-c) keys and the paste (Ctrl-v) keys. If your "IP address" does not start with 192.168 , then for security reasons, erase the last half of your IP address.
Kudos! Thanks!

2Wire + Airport Connection issue (Help wanted)

Hello All,
I use a 2Wire HomePortal router to connect to my DSL service, and it works very well with our old PC and my iMac G5 (both ethernet and wireless). I purchased my new MacBook in August, and It connected well to the 2wire network, until two days ago. Right now, all I can connect to with the HomePortal router is via ethernet, which works fine. When I attempt to connect by wireless, I recieve the message "There was an error connecting to 2wire*" It's WEP passcoded, but I already know that I need to put a $ in front of the passkey, so I doubt that's the problem. Also, I can connect to other wireless networks, so I know it isn't a general AirPort problem.
Thanks so much for your help!
-Belril

I'm not sure how helpful this may be, but I also use a 2WIRE router/modem for my DSL connection. I initially had problems with it and here are the thide ngs that I did to get the connection to work:
1. Reset the router (I unplugged it and plugged it back in after about 30 seconds)
2. Made sure that I used the right version of WEP on the AirPort. I had to use the hex key choice to get it to connect.
After that all was well.
Good luck...

JCA binding error in bpel(11g)

Hi all,
I have created a DB adapter in BPEL and have deployed the bpel, when i tested the service i got this below error
java.lang.Exception: oracle.sysman.emSDK.webservices.wsdlapi.SoapTestException: Exception occured when binding was invoked. Exception occured during invocation of JCA binding: "JCA Binding execute of Reference operation 'AddressValidationListSelect' failed due to: JCA Binding Component connection issue. JCA Binding Component is unable to create an outbound JCA (CCI) connection. AddressValidation:AddressValidationList [ AddressValidationList_ptt::AddressValidationListSelect(AddressValidationListSelect_inputParameters,TbgnStreetCollection) ] : The JCA Binding Component was unable to establish an outbound JCA CCI connection due to the following issue: BINDING.JCA-12510 JCA Resource Adapter location error. Unable to locate the JCA Resource Adapter via .jca binding file element <connection-factory/> The JCA Binding Component is unable to startup the Resource Adapter specified in the <connection-factory/> element: location='eis/DB/11g'. The reason for this is most likely that either 1) the Resource Adapters RAR file has not been deployed successfully to the WebLogic Application server or 2) the '<jndi-name>' element in weblogic-ra.xml has not been set to eis/DB/11g. In the last case you will have to add a new WebLogic JCA connection factory (deploy a RAR). Please correct this and then restart the Application Server ". The invoked JCA adapter raised a resource exception. Please examine the above error message carefully to determine a resolution. at oracle.sysman.emas.model.wsmgt.WSTestModel.invokeOperation(WSTestModel.java:575) at oracle.sysman.emas.view.wsmgt.WSView.invokeOperation(WSView.java:381) at oracle.sysman.emas.view.wsmgt.WSView.invokeOperation(WSView.java:298) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at com.sun.el.parser.AstValue.invoke(AstValue.java:157) at com.sun.el.MethodExpressionImpl.invoke(MethodExpressionImpl.java:283) at org.apache.myfaces.trinidadinternal.taglib.util.MethodExpressionMethodBinding.invoke(MethodExpressionMethodBinding.java:53) at org.apache.myfaces.trinidad.component.UIXComponentBase.broadcastToMethodBinding(UIXComponentBase.java:1245) at org.apache.myfaces.trinidad.component.UIXCommand.broadcast(UIXCommand.java:183) at oracle.adf.view.rich.component.fragment.ContextSwitchingComponent$1.run(ContextSwitchingComponent.java:90) at oracle.adf.view.rich.component.fragment.ContextSwitchingComponent._processPhase(ContextSwitchingComponent.java:309) at oracle.adf.view.rich.component.fragment.ContextSwitchingComponent.broadcast(ContextSwitchingComponent.java:94) at oracle.adf.view.rich.component.fragment.UIXInclude.broadcast(UIXInclude.java:102) at oracle.adf.view.rich.component.fragment.ContextSwitchingComponent$1.run(ContextSwitchingComponent.java:90) at oracle.adf.view.rich.component.fragment.ContextSwitchingComponent._processPhase(ContextSwitchingComponent.java:309) at oracle.adf.view.rich.component.fragment.ContextSwitchingComponent.broadcast(ContextSwitchingComponent.java:94) at oracle.adf.view.rich.component.fragment.UIXInclude.broadcast(UIXInclude.java:96) at javax.faces.component.UIViewRoot.broadcastEvents(UIViewRoot.java:475) at javax.faces.component.UIViewRoot.processApplication(UIViewRoot.java:756) at oracle.adfinternal.view.faces.lifecycle.LifecycleImpl._invokeApplication(LifecycleImpl.java:698) at oracle.adfinternal.view.faces.lifecycle.LifecycleImpl._executePhase(LifecycleImpl.java:285) at oracle.adfinternal.view.faces.lifecycle.LifecycleImpl.execute(LifecycleImpl.java:177) at javax.faces.webapp.FacesServlet.service(FacesServlet.java:265) at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:227) at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:125) at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:292) at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:26) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.adfinternal.view.faces.webapp.rich.RegistrationFilter.doFilter(RegistrationFilter.java:97) at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl$FilterListChain.doFilter(TrinidadFilterImpl.java:420) at oracle.adfinternal.view.faces.activedata.AdsFilter.doFilter(AdsFilter.java:60) at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl$FilterListChain.doFilter(TrinidadFilterImpl.java:420) at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl._doFilterImpl(TrinidadFilterImpl.java:247) at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl.doFilter(TrinidadFilterImpl.java:157) at org.apache.myfaces.trinidad.webapp.TrinidadFilter.doFilter(TrinidadFilter.java:92) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.help.web.rich.OHWFilter.doFilter(Unknown Source) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.sysman.emSDK.license.LicenseFilter.doFilter(LicenseFilter.java:101) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.adf.model.servlet.ADFBindingFilter.doFilter(ADFBindingFilter.java:191) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.sysman.emas.fwk.MASConnectionFilter.doFilter(MASConnectionFilter.java:41) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.adf.library.webapp.LibraryFilter.doFilter(LibraryFilter.java:159) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.sysman.eml.app.AuditServletFilter.doFilter(AuditServletFilter.java:179) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.sysman.eml.app.EMRepLoginFilter.doFilter(EMRepLoginFilter.java:203) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.sysman.core.app.perf.PerfFilter.doFilter(PerfFilter.java:141) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.sysman.eml.app.ContextInitFilter.doFilter(ContextInitFilter.java:542) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.dms.wls.DMSServletFilter.doFilter(DMSServletFilter.java:326) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at weblogic.servlet.internal.RequestEventsFilter.doFilter(RequestEventsFilter.java:27) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:3592) at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321) at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:121) at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2202) at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2108) at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1432) at weblogic.work.ExecuteThread.execute(ExecuteThread.java:201) at weblogic.work.ExecuteThread.run(ExecuteThread.java:173) Caused by: oracle.sysman.emSDK.webservices.wsdlapi.SoapTestException: Exception occured when binding was invoked. Exception occured during invocation of JCA binding: "JCA Binding execute of Reference operation 'AddressValidationListSelect' failed due to: JCA Binding Component connection issue. JCA Binding Component is unable to create an outbound JCA (CCI) connection. AddressValidation:AddressValidationList [ AddressValidationList_ptt::AddressValidationListSelect(AddressValidationListSelect_inputParameters,TbgnStreetCollection) ] : The JCA Binding Component was unable to establish an outbound JCA CCI connection due to the following issue: BINDING.JCA-12510 JCA Resource Adapter location error. Unable to locate the JCA Resource Adapter via .jca binding file element <connection-factory/> The JCA Binding Component is unable to startup the Resource Adapter specified in the <connection-factory/> element: location='eis/DB/11g'. The reason for this is most likely that either 1) the Resource Adapters RAR file has not been deployed successfully to the WebLogic Application server or 2) the '<jndi-name>' element in weblogic-ra.xml has not been set to eis/DB/11g. In the last case you will have to add a new WebLogic JCA connection factory (deploy a RAR). Please correct this and then restart the Application Server ". The invoked JCA adapter raised a resource exception. Please examine the above error message carefully to determine a resolution. at oracle.sysman.emSDK.webservices.wsdlapi.dispatch.DispatchUtil.invoke(DispatchUtil.java:260) at oracle.sysman.emSDK.webservices.wsdlparser.OperationInfoImpl.invokeWithDispatch(OperationInfoImpl.java:985) at oracle.sysman.emas.model.wsmgt.PortName.invokeOperation(PortName.java:716) at oracle.sysman.emas.model.wsmgt.WSTestModel.invokeOperation(WSTestModel.java:569) ... 68 more Caused by: javax.xml.ws.soap.SOAPFaultException: Exception occured when binding was invoked. Exception occured during invocation of JCA binding: "JCA Binding execute of Reference operation 'AddressValidationListSelect' failed due to: JCA Binding Component connection issue. JCA Binding Component is unable to create an outbound JCA (CCI) connection. AddressValidation:AddressValidationList [ AddressValidationList_ptt::AddressValidationListSelect(AddressValidationListSelect_inputParameters,TbgnStreetCollection) ] : The JCA Binding Component was unable to establish an outbound JCA CCI connection due to the following issue: BINDING.JCA-12510 JCA Resource Adapter location error. Unable to locate the JCA Resource Adapter via .jca binding file element <connection-factory/> The JCA Binding Component is unable to startup the Resource Adapter specified in the <connection-factory/> element: location='eis/DB/11g'. The reason for this is most likely that either 1) the Resource Adapters RAR file has not been deployed successfully to the WebLogic Application server or 2) the '<jndi-name>' element in weblogic-ra.xml has not been set to eis/DB/11g. In the last case you will have to add a new WebLogic JCA connection factory (deploy a RAR). Please correct this and then restart the Application Server ". The invoked JCA adapter raised a resource exception. Please examine the above error message carefully to determine a resolution. at oracle.j2ee.ws.client.jaxws.DispatchImpl.throwJAXWSSoapFaultException(DispatchImpl.java:882) at oracle.j2ee.ws.client.jaxws.DispatchImpl.invoke(DispatchImpl.java:715) at oracle.j2ee.ws.client.jaxws.OracleDispatchImpl.synchronousInvocationWithRetry(OracleDispatchImpl.java:226) at oracle.j2ee.ws.client.jaxws.OracleDispatchImpl.invoke(OracleDispatchImpl.java:97) at oracle.sysman.emSDK.webservices.wsdlapi.dispatch.DispatchUtil.invoke(DispatchUtil.java:256) ... 71 more
View Log MessagesSaveClose
I checked for Dbadapter process unser soa_server its up and running
Kindly help me
Thank You

Hi all,
I have created a DB adapter in BPEL and have deployed the bpel, when i tested the service i got this below error
java.lang.Exception: oracle.sysman.emSDK.webservices.wsdlapi.SoapTestException: Exception occured when binding was invoked. Exception occured during invocation of JCA binding: "JCA Binding execute of Reference operation 'AddressValidationListSelect' failed due to: JCA Binding Component connection issue. JCA Binding Component is unable to create an outbound JCA (CCI) connection. AddressValidation:AddressValidationList [ AddressValidationList_ptt::AddressValidationListSelect(AddressValidationListSelect_inputParameters,TbgnStreetCollection) ] : The JCA Binding Component was unable to establish an outbound JCA CCI connection due to the following issue: BINDING.JCA-12510 JCA Resource Adapter location error. Unable to locate the JCA Resource Adapter via .jca binding file element <connection-factory/> The JCA Binding Component is unable to startup the Resource Adapter specified in the <connection-factory/> element: location='eis/DB/11g'. The reason for this is most likely that either 1) the Resource Adapters RAR file has not been deployed successfully to the WebLogic Application server or 2) the '<jndi-name>' element in weblogic-ra.xml has not been set to eis/DB/11g. In the last case you will have to add a new WebLogic JCA connection factory (deploy a RAR). Please correct this and then restart the Application Server ". The invoked JCA adapter raised a resource exception. Please examine the above error message carefully to determine a resolution. at oracle.sysman.emas.model.wsmgt.WSTestModel.invokeOperation(WSTestModel.java:575) at oracle.sysman.emas.view.wsmgt.WSView.invokeOperation(WSView.java:381) at oracle.sysman.emas.view.wsmgt.WSView.invokeOperation(WSView.java:298) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at com.sun.el.parser.AstValue.invoke(AstValue.java:157) at com.sun.el.MethodExpressionImpl.invoke(MethodExpressionImpl.java:283) at org.apache.myfaces.trinidadinternal.taglib.util.MethodExpressionMethodBinding.invoke(MethodExpressionMethodBinding.java:53) at org.apache.myfaces.trinidad.component.UIXComponentBase.broadcastToMethodBinding(UIXComponentBase.java:1245) at org.apache.myfaces.trinidad.component.UIXCommand.broadcast(UIXCommand.java:183) at oracle.adf.view.rich.component.fragment.ContextSwitchingComponent$1.run(ContextSwitchingComponent.java:90) at oracle.adf.view.rich.component.fragment.ContextSwitchingComponent._processPhase(ContextSwitchingComponent.java:309) at oracle.adf.view.rich.component.fragment.ContextSwitchingComponent.broadcast(ContextSwitchingComponent.java:94) at oracle.adf.view.rich.component.fragment.UIXInclude.broadcast(UIXInclude.java:102) at oracle.adf.view.rich.component.fragment.ContextSwitchingComponent$1.run(ContextSwitchingComponent.java:90) at oracle.adf.view.rich.component.fragment.ContextSwitchingComponent._processPhase(ContextSwitchingComponent.java:309) at oracle.adf.view.rich.component.fragment.ContextSwitchingComponent.broadcast(ContextSwitchingComponent.java:94) at oracle.adf.view.rich.component.fragment.UIXInclude.broadcast(UIXInclude.java:96) at javax.faces.component.UIViewRoot.broadcastEvents(UIViewRoot.java:475) at javax.faces.component.UIViewRoot.processApplication(UIViewRoot.java:756) at oracle.adfinternal.view.faces.lifecycle.LifecycleImpl._invokeApplication(LifecycleImpl.java:698) at oracle.adfinternal.view.faces.lifecycle.LifecycleImpl._executePhase(LifecycleImpl.java:285) at oracle.adfinternal.view.faces.lifecycle.LifecycleImpl.execute(LifecycleImpl.java:177) at javax.faces.webapp.FacesServlet.service(FacesServlet.java:265) at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:227) at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:125) at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:292) at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:26) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.adfinternal.view.faces.webapp.rich.RegistrationFilter.doFilter(RegistrationFilter.java:97) at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl$FilterListChain.doFilter(TrinidadFilterImpl.java:420) at oracle.adfinternal.view.faces.activedata.AdsFilter.doFilter(AdsFilter.java:60) at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl$FilterListChain.doFilter(TrinidadFilterImpl.java:420) at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl._doFilterImpl(TrinidadFilterImpl.java:247) at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl.doFilter(TrinidadFilterImpl.java:157) at org.apache.myfaces.trinidad.webapp.TrinidadFilter.doFilter(TrinidadFilter.java:92) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.help.web.rich.OHWFilter.doFilter(Unknown Source) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.sysman.emSDK.license.LicenseFilter.doFilter(LicenseFilter.java:101) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.adf.model.servlet.ADFBindingFilter.doFilter(ADFBindingFilter.java:191) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.sysman.emas.fwk.MASConnectionFilter.doFilter(MASConnectionFilter.java:41) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.adf.library.webapp.LibraryFilter.doFilter(LibraryFilter.java:159) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.sysman.eml.app.AuditServletFilter.doFilter(AuditServletFilter.java:179) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.sysman.eml.app.EMRepLoginFilter.doFilter(EMRepLoginFilter.java:203) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.sysman.core.app.perf.PerfFilter.doFilter(PerfFilter.java:141) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.sysman.eml.app.ContextInitFilter.doFilter(ContextInitFilter.java:542) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at oracle.dms.wls.DMSServletFilter.doFilter(DMSServletFilter.java:326) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at weblogic.servlet.internal.RequestEventsFilter.doFilter(RequestEventsFilter.java:27) at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56) at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:3592) at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321) at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:121) at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2202) at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2108) at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1432) at weblogic.work.ExecuteThread.execute(ExecuteThread.java:201) at weblogic.work.ExecuteThread.run(ExecuteThread.java:173) Caused by: oracle.sysman.emSDK.webservices.wsdlapi.SoapTestException: Exception occured when binding was invoked. Exception occured during invocation of JCA binding: "JCA Binding execute of Reference operation 'AddressValidationListSelect' failed due to: JCA Binding Component connection issue. JCA Binding Component is unable to create an outbound JCA (CCI) connection. AddressValidation:AddressValidationList [ AddressValidationList_ptt::AddressValidationListSelect(AddressValidationListSelect_inputParameters,TbgnStreetCollection) ] : The JCA Binding Component was unable to establish an outbound JCA CCI connection due to the following issue: BINDING.JCA-12510 JCA Resource Adapter location error. Unable to locate the JCA Resource Adapter via .jca binding file element <connection-factory/> The JCA Binding Component is unable to startup the Resource Adapter specified in the <connection-factory/> element: location='eis/DB/11g'. The reason for this is most likely that either 1) the Resource Adapters RAR file has not been deployed successfully to the WebLogic Application server or 2) the '<jndi-name>' element in weblogic-ra.xml has not been set to eis/DB/11g. In the last case you will have to add a new WebLogic JCA connection factory (deploy a RAR). Please correct this and then restart the Application Server ". The invoked JCA adapter raised a resource exception. Please examine the above error message carefully to determine a resolution. at oracle.sysman.emSDK.webservices.wsdlapi.dispatch.DispatchUtil.invoke(DispatchUtil.java:260) at oracle.sysman.emSDK.webservices.wsdlparser.OperationInfoImpl.invokeWithDispatch(OperationInfoImpl.java:985) at oracle.sysman.emas.model.wsmgt.PortName.invokeOperation(PortName.java:716) at oracle.sysman.emas.model.wsmgt.WSTestModel.invokeOperation(WSTestModel.java:569) ... 68 more Caused by: javax.xml.ws.soap.SOAPFaultException: Exception occured when binding was invoked. Exception occured during invocation of JCA binding: "JCA Binding execute of Reference operation 'AddressValidationListSelect' failed due to: JCA Binding Component connection issue. JCA Binding Component is unable to create an outbound JCA (CCI) connection. AddressValidation:AddressValidationList [ AddressValidationList_ptt::AddressValidationListSelect(AddressValidationListSelect_inputParameters,TbgnStreetCollection) ] : The JCA Binding Component was unable to establish an outbound JCA CCI connection due to the following issue: BINDING.JCA-12510 JCA Resource Adapter location error. Unable to locate the JCA Resource Adapter via .jca binding file element <connection-factory/> The JCA Binding Component is unable to startup the Resource Adapter specified in the <connection-factory/> element: location='eis/DB/11g'. The reason for this is most likely that either 1) the Resource Adapters RAR file has not been deployed successfully to the WebLogic Application server or 2) the '<jndi-name>' element in weblogic-ra.xml has not been set to eis/DB/11g. In the last case you will have to add a new WebLogic JCA connection factory (deploy a RAR). Please correct this and then restart the Application Server ". The invoked JCA adapter raised a resource exception. Please examine the above error message carefully to determine a resolution. at oracle.j2ee.ws.client.jaxws.DispatchImpl.throwJAXWSSoapFaultException(DispatchImpl.java:882) at oracle.j2ee.ws.client.jaxws.DispatchImpl.invoke(DispatchImpl.java:715) at oracle.j2ee.ws.client.jaxws.OracleDispatchImpl.synchronousInvocationWithRetry(OracleDispatchImpl.java:226) at oracle.j2ee.ws.client.jaxws.OracleDispatchImpl.invoke(OracleDispatchImpl.java:97) at oracle.sysman.emSDK.webservices.wsdlapi.dispatch.DispatchUtil.invoke(DispatchUtil.java:256) ... 71 more
View Log MessagesSaveClose
I checked for Dbadapter process unser soa_server its up and running
Kindly help me
Thank You

JCA Binding Component connection issue - Help plz

Similar Messages

Maybe you are looking for