Just thought id update my Iphone 4, But now it wont restore, wont turn on, and whe it restores i get a frozen loading screen with the apple logo above it? Have to hard reset for it to disappear. Any one help?
As above really..
Im in no way a computer wiz so im struggling to even see whats wrong?
Why has this happened?
Thanks
See here - http://support.apple.com/kb/TS3694#error1603
Similar Messages
-
i've tried to set up a new user on a mac book pro and i restarted it to create the new account but now all i can get is a white screen with the apple logo and the loading symbol what can i do ?
Look at this support article:
http://support.apple.com/kb/ts2570
Ciao. -
Hello, I can't turn my iphone 4s on, it just broke down and now there's just the black screen with the apple logo on it. So I connected it to itunes and tried to restore it, but than always the errors 1603 & 1611 appeared! please help me!!
You may have a faulty USB cable. Try another.
Make sure you are following the instructions in this procedure to the letter. Here they are, with emphasis on some easily overlooked requirements:
Disconnect the USB cable from the iPhone, but leave the other end of the cable connected to your computer's USB port.
Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.If you cannot turn off the device using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the device turns off, release only the Sleep/Wake button.
Continue pressing and holding the Home button while you reconnect the USB cable to the device. The device should turn on.Note: If you see the "low battery" screen, let the device charge for at least ten minutes to ensure that the battery has some charge, and then start with step 2 again.
Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears (iTunes icon and USB connector) release the Home button.
If necessary, open iTunes. You should see the "recovery mode" alert ("iTunes has detected a phone in recovery mode").
Use iTunes to restore the iPhone.
If you do not see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
Select the device in iTunes and choose "restore from backup".
If you still can't get it to work, you have done all you can and only Apple will be able to help. -
i have a screen with the apple logo on it and a bar underneath it. it has been this way for about an hour now. what does this mean and is there a way to reset the iphone without going into the store? it isnt showing in my computer or on the itunes page.
Try:
- iOS: Not responding or does not turn on
- If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order. -
I have just got a replacement iphone 5 but I can't restore my old backup that is ios7 because the replacement is ios6 I have changed my UDID on the developer site but still no luck any suggestions anyone?
You are in breach of your Developer agreement by posting in a Public forum
-
I tried to reset my iphone 5 from the phone and not a computer. I have had a blank screen with the apple logo and a full progress bar. I can not get my phone to restart. What can I do?
Sorry i meant iOs5 to ios 5.0.1
-
It has been on this black screen with the apple logo and some small white writing at the top of the screen for many hours. I've tried rebooting it and connecting to iTunes but nothing has worked.
PLEASE HELP!!!!!!!!It likely means there was still water inside it and something has now shorted out and permanently damaged one or more components. THE very worst thing you can do with wet electronics is energize them - even a small drop of water inside on any of the circuitry or electrical contacts can cause catastrophic damage.
Take it to Apple for a free evaluation, but most likely you will need to replace it. For the out of warranty fee ($269.00 USD) you will get a refurbished replacement (like new, with a factory new screen and battery). An out of warranty replacement will also re-instate your remaining warranty, or 90 days warranty, whichever is longer. -
My MacBook Air will not turn on. I get a white screen with the apple logo and a spinning star (search icon). It will spin for hours and never go away unless I power off.
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
My 5th generation iPod (bought in April of 2013) will quit unexpectedly. I can't do app store apps (like snapchat or facebook, ect.) or apple apps (like Camera, Safari, ect.)It will take for ever to load what I write while texting. It also just goes to the black screen with the Apple logo. I'm not sure what to do.
Try This...
Close All Open Apps... Sign Out of your Account... Perform a Reset... Try again...
Reset ( No Data will be Lost )
Press and Hold the Sleep/Wake Button and the Home Button at the Same Time...
Wait for the Apple logo to Appear...
Usually takes about 15 - 20 Seconds... ( But can take Longer...)
Release the Buttons...
If no joy...
Reset all settings
Settings > General > Reset > Reset all Settings.
This will return all iDevice settings to factory defaults... you will not lose any data.... But you will have to re-enter all of the device settings.
If the issue persists...
Connect to iTunes on the computer you usually Sync with and Restore
http://support.apple.com/kb/HT1414
Make sure you have the Latest Version of iTunes (v11) Installed on your computer
iTunes free download from www.itunes.com/download
More Tips here...
http://osxdaily.com/2013/09/23/ios-7-slow-speed-it-up/
http://osxdaily.com/2013/09/19/ios-7-battery-life-fix/
Note:
Also consider Deleting any Apps you have Purchased / Downloaded but you now never use. -
Hey everyone,
This morning i took my phone out of the charger and everything was normal however, once i got in the car i looked at my phone and realized it was turned off. I tried turning it on again as well but all it does is going to the start up screen (The white screen with the apple logo) and then it turns off again as well. I also put it on the charger but it does the same thing but repeatedly. So it just goes to the white screen and off again. At last i resorted to recovering my phone even if it meant losing all my data. Slow internet connection meant it took all night but in the morning i recovered and everything and got to the last step ( It told me its finished but i should leave my phone connected to itunes and it will pop up there) but all that popped up was an error screen. It still broken but now sometimes when i try to turn it on the same white screen with the logo comes on with a bar under it. this bar fills up a little then the screen goes black again. Is there any other way i can try to fix this?
P.S. There are no apple stores in my area so i took it to one of the phone stores here and even they said they couldnt do anything about itTry:
- iOS: Not responding or does not turn on
- If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order. -
After installing the above mentioned update, my ipad will no longer turn on. I have just a black screen with the apple logo when I attach it to a power source. Anyone else having this problem, please advise on how to fix.
IF RESET DOESN'T WORK, FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port. Do not release button until you see picture of iTunes and plug (very important)
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note: Data will be lost -
My iphone will not turn on.... it froze earlier today and now it will not turn on all i get is a black screen with the apple symbol every once in awhile... also it will not connect to my computer so i can reset it to factory settings
Sammyhunter lets get you back in action! Has there been any physical/water damage to the device? Try pressing and holding the home and power button together. Once the Apple symbol appears release both buttons. Keep us posted!
AshleyS_VZW
Follow us on Twitter @VZWSupport -
After updating to iOS 5.0.1 my iphone 4 is frozen on the screen with the apple logo and the progress bar under it. Held the power and home button, the phone shut off, and restarted the progress. If i try to turn the phone on, it keeps telling me to connect to iTunes. Once I do, it asks me to restore, i click restore, but it keeps on freezing at the screen. What is the problem? Error 1603 comes up. Followed the link to apple's page but nothing that was said there worked.
See Here for
Unable to Update or Restore
http://support.apple.com/kb/HT1808 -
My MacBook Pro stated that it needed to be updated. I clicked yes to restart the computer and update but when it restarted it stays on the gray screen with the apple logo and then pops up, stating "unable to find driver for this platform." What do I do?
Boot into Recovery by holding down the key combination command-R at the startup chime. Release the keys when you see a gray screen with a spinning dial.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with networks that require any kind of authentication other than a WPA or WPA2 Personal password.
When the Mac OS X Utilities screen appears, follow the prompts to reinstall the Mac OS. You don't need to erase the boot volume, and you won't need your backup unless something goes wrong. If your Mac didn’t ship with Lion, you’ll need the Apple ID and password you used to upgrade, so make a note of those before you begin.
Don't install the Thunderbolt update -- it's defective. -
My iphone 5 died so I plugged it back in to charge and it will not turn on. It will turn to the screen with the apple logo and black screen then turn off again. Any suggestions?
I leave it charging until it gets back to full, usually it turns on after a little bit of time after plugging it in, but all its doing is going to the apple logo screen and going blank again.
Maybe you are looking for
-
How to remove bullets and spacing for url links in the Related Links iview?
I tried to look for a property that I can edit the look-n-feel of the url links in the Related Link iView using "Theme Editor". All I need is to remove the bullets and increase some vertical spacing between the links. Currently, it looks like this: U
-
Problem installing oracle developer Suite 10g on window 7 64 bit
hi am in window 7 64-bit am trying to install my oracle developer suite am geting this error when installing Starting Oracle Universal Installer... Checking installer requirements... Checking operating system version: must be 5.0, 5.1 or 5.2 . Actual
-
High availability SQL Server requirements for Remote Desktop Services in Windows Server 2012
Good night, Thanks for reading this question, I do not write much English. I am implementing Remote Desktop Services in Windows Server 2012, I need to know the size of the database to create and feature on the .mdf and .ldf, I searched in different m
-
Hi All, I have created one addon for MRP in this addon when client click on menu i have to display "Order recomandation" form which will dispaly in existing MRP functions. How to display existing sap form in our menuclick. please help me as soon as
-
SMS/SCCM & Batch Files - Important notes on running .BAT files from UNC in SMS/SCCM
http://www.myitforum.com/articles/42/view.asp?id=12036 Cheers, David Goldberg National Instruments Software R&D