LAP manual configuration

Hello All
I have to manually configure my 1131 LAPs for controllers IP addresses.
I configured one of them. It joined the controller and downloaded the new code and config. I then cleared its config. Now it does not find the controller.
When I try to re-configure the controller IP address, I get "AccessPoint#clear lwapp ap controller ip address
ERROR!!! Command is disabled."
On the following page it states that I should do:
set the username/password of the AP from the controller CLI with the config ap username <name> password <pwd> <cisco-ap>/all command.
But, there is no config command on the version
"flash:/c1130-k9w8-mx.124-10b.JDA1/c1130-k9w8-mx.124-10b.JDA1"
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_qanda_item09186a00806a4da3.shtml
Thanks a lot
Bo

"clear lwapp ap controller ip address" and "lwapp ap controller ip address" commands work only while running a recovery image that you use to convert from Autonomous to LAP. Once the LAP joins the WLC, it will download the new LWAPP image and overwrite the recovery image. LWAPP image doesn't allow you to use those commands.
You have two options:
1. Convert it back to Autonomous, then convert back to LAP using recovery image. You can then prime it with the controller IP address with those commands. Converting back to autonomous is a very quick and easy procedure
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
2. Use another method to discover WLC's IP:
a. Put the LAP on the same subnet as the WLC's MGMT IP. LAP will use 255.255.255.255 broadcast to find it.
b. Configure DHCP on a local IOS default gateway to provide option 43 and reboot the LAP. Something like this:
ip dhcp pool TEST
network 192.168.0.0 255.255.255.0
default-router 192.168.0.1
option 43 hex f104.032d.2f90
f1 = 241 (leave as is)
04 = 4 octets IP address.
032d.2f90 = 3.45.47.144 (MGMT IP address of my WLC)
c. Configure DHCP on local IOS default gateway to provide DNS server and domain name to the LAP. Make sure your DNS server resolves "CISCO-LWAPP-CONTROLLER.domain.com" to WLC's mgmt IP.
ip dhcp pool TEST
network 192.168.0.0 255.255.255.0
default-router 192.168.0.1
domain-name domain.com
dns-server

Similar Messages

How do I manually configure a Timecapsule after having restored it to original settings?

I have been experiencing very slow wifi speeds over my wireless and having done some research on the topic, many suggest that completely eliminating previous settings by restoring the Timecapsule and manually reconfiguring it may help. I have tried to do this, but despite changing the setting to "manually configure" in the hardware settings in the airport utility, every time I restore Timecapsule and begin to configure it, it tells me that it is reading the settings from the base station.
In addition, despite removing the check mark from the "remember previously joined networks" in airport utility, it still lists my previous SSID in the list of networks.
Since the wireless speed hasn't improved at all (in fact, it has deteriorated some) I am afraid the old set ups are still there and slowing things down. How can I completely remove all previous settings from my Timecapsule, my airport express and the airport utility software and start from scratch?
Thanks.

How can I completely remove all previous settings from my Timecapsule, my airport express and the airport utility software and start from scratch?
There are two parts to this answer. The first relates to performing a Factory Default Reset separately on the Time Capsule and AirPort Express. This will erase the current network settings and return them to default values. This will not affect any backups that you may have stored on the Time Capsule disk. ***
Use the information in this Apple support document for that:
Resetting an AirPort Base Station or Time Capsule FAQ
Part two would be to delete the previous wireless settings on your iMac. Here's how:
Open System Preferences (gear icon on the dock)
Open Network
Open Wi-Fi or AirPort
Click Advanced at the lower right of the window
Click on the name of a wireless network that you no longer need to highlight it
Click the - (minus) button at the bottom of the list to delete it
Do the same for other networks that you no longer need
Click OK, then click Apply
Open Macintosh HD > Applications > Utilities > KeyChain Access
Click on the name of a wireless network that you want to delete to highlight it
Click the Delete key on your keyboard
Do the same for other networks that you no longer need
Close KeyChain Access
*** If you need to erase the Time Capsule disk completely, post back for additional instructions. We need to know which version of AirPort Utility you are using to provide specific details.

ALE-manual configuration of the customer distribution model

DEAR EXPERTS
how do i manually configure the customer distribution model

hi ,
to maintain or configure the customer distribution model (CDM)
go to tcode BD64.
give the sender address -
you have to mention the logical system name of the sender system. if u r sending one version to other then you have to specify the sender system address,
give the receiver address--- same as above but mention the details of receiver system.
meaintain the message type--- depends upon the type of applicaiton using like MATMAS or ........
do the same procedure again in the reverse way to transer the information from one system to other system and vice versa.
next step is to generate partner profiles.
BD82 is the tcode for it
next distribute CDM.
thats it.
If u find it useful mark the points
Regards,
GNK.

Mail 3 manual configuration?

How do I manually configure a new account in Mail 3? I don't want to automatically figure out my settings. I want to tell it what my settings are.

I want to create a new mail account without using the help that comes up automatically when you choose new account under file. How can I just get an account screen that looks like it does after you have created an account but that I can enter the information myself without the automatic program that asks the questions?
Thank you very much.

Proxy 4.04 : Manual configurations of .conf files not loading

Hello,
Apologies if i sound a bit noobish , but some questions regarding manually configuring files (*.conf) using notepad/vi.
Issue now is , whenever i use a script or manually copy & paste newer configs, i do not get prompted for the reload configuration prompt like in 3.6. While i do realize the software supports dynamic reconfiguration , but i noticed that there is no updates show in my admin server (e.g , updated templates in obj.conf but in admin server -> view templates , it's not showing). And no prompt to "load configuration files). I'm running java that came with the package itself btw.

Hello,
Apologies if i sound a bit noobish , but some questions regarding manually configuring files (*.conf) using notepad/vi.
Issue now is , whenever i use a script or manually copy & paste newer configs, i do not get prompted for the reload configuration prompt like in 3.6. While i do realize the software supports dynamic reconfiguration , but i noticed that there is no updates show in my admin server (e.g , updated templates in obj.conf but in admin server -> view templates , it's not showing). And no prompt to "load configuration files). I'm running java that came with the package itself btw.

Manually configure WCS as an SNMP Trap Receiver?

If I discover a WLC through the WCS, do I still need to manually configure the WCS as an SNMP trap receiver on the WLC?

The WCS machine must be configured as an SNMP trap receiver to have full management functionality through the WCS.

Manual configuration - quick question!

The Dutch translation of the Airport extreme (7.1) software has a small mistake in the manual configuration part.
Under the menu "Airport" (button)
The third tab "Wireless"
There's 1 checkbox here below the "network name" text field.
What is it saying?
In Dutch we only get to see a part of the sentence.
Thanks for the help.

Ok guys, found it out, it's "allow this network to be extended".

HT4259 Why does my Airport utility not have either an option to manually configure, or a box "to extend the network?"

I have Mac with Lion, with an AIrport Extreme wi-fi network. I am trying to configure a Airport (model A1264) to extend the network. I read the Apple article on how to configure an extended network. Unfortunately my Airport Utility seems to have none of the functionality mentioned in the article. The article states to choose manual configuration of the base station. I can find no such option in my Airport Utility. Secondly, it the article states to check "create a wireless network," which I can find, but then says to check box to "allow this network to be extended." No such option appears anywhere in my Airport Utility. Lastly, my Mac is not even recognizing the existence of the Airport Express. It does not even appear as a wireless device, nor does it appear in Airport Utility as an "Other Airport Base Stations. It does however continue to flash amber. Does anyone know what might be the problem?
Thanks,
bmarr

I read the Apple article on how to configure an extended network. Unfortunately my Airport Utility seems to have none of the functionality mentioned in the article.
The article was written a few years ago and Lion 10.7.4 was not around at the time.
I suggest that you download and install the full featured version of AirPort Utility 5.6 for Mac OS X Lion . I think you will find that it will track with the article (if it is the one that I think it is) very nicely.
You can keep both AirPort Utility 5.6 and AirPort Utility 6.0 on your Mac.

RE:manual configuration of the customer distribution model

i hae entered tcode bd64 for manual configuration of the customer distribution model but now i dont know where to go to to put the sende and receiver addresses. i am stuck guys, please helb

Please refer this blog.
/people/kevin.wilson2/blog/2006/11/13/ale-scenario-development-guide
http://searchsap.techtarget.com/general/0,295582,sid21_gci1130337,00.html
Regards,
Ramki.

Manual configuration of intermedia

I have installed Oracle 8.1.6 with intermedia. There appear to be some configuration problems. How do I manually configure intermedia?

In your <ORACLE_HOME>/ord/im/admin directory, there is a README.txt file. This talks about installation of interMedia. Go to the section "3 Installation Steps" under "Installing Oracle interMedia". It lists the things you need to do for mannual installation.
null

Wireless Print Server (DPR-1260) - Manually Configure Printer Port

I am trying to get my DPR-1260 Wireless Print Server (PS) installed, and need help with manually configuring the printer port (per Dlink).
Status:
A) Before trying to install the PS, I was able to easily install (2) USB printers, see them, and print to them.
B) My new IMAC is hardwired to the router.
*Recent Actions:*
1) I've worked with Dlink and have verified that my network (my new IMAC, and my wife's wireless laptop (OS 10.39) see the PS (hooked directly to the router). It's IP address is 192.168.0.102 .
2) I hooked both printers to the PS, and the address sees both printers as installed, and provide with LPR information (both printers are now hooked to the PS). Dlink does not guarantee printer compatibility, but says that since the site sees the printers, gives me LPRs, that the probability is good that they will be compatiable.
3) My new IMAC sees this address in both OS and in XP (thru VM Fusion). My laptop (10.3x) also sees this address. However, I'm not able to install this printer.
4) Per Dlink, I need to manually configure the printer port to install the PS.
5) Dlink kept sending me to the Print Utility, but from what I see, that does not exist in 10.5.
How do I manually configure the printer port to see the PS?
Now, I am stuck, and help?
Many thanks

As DLink have said, you will have to manually configure a LPR queue to connect to your printers. The print utility in 10.5 is the Print & Fax util in System Preferences. Open this and choose to Add . Select IP and then LPR. Enter the ip address of the PS. Then you will need a queue name for the respective USB ports, such as P1 and P2, or something similar. Hopefully the DLink info mentions this so that you can print to the desired printer.
The final bit of info you will need to know is whether the printer driver for each printer will work in this type of network. If either of them is a Canon then there is a good chance you will not be able to use supplied drivers. These types of connections require a third party driver, like Gutenprint, which is usually installed by default. If you are not sure, then please tell us which brands and models of printer you have.
PaHu

Unable to query IPv4 router of manually configured interface

I need to determine the IPv4 router for a given Ethernet/WiFi interface.
The route table can not always be used to determine the router in the case of a multi-homed system.
So, the SystemConfiguration framework seems to be the right choice to use by querying the kSCPropNetIPv4Router property from the network service associated with the interface.
This works fine assuming the Ethernet or WiFi interface is configured using DHCP. However, if the interface is manually configured then the kSCPropNetIPv4Router property doesn't seem to exist!
I have a sample program which illustrates this and scutil seems to show the same thing.
Any help?

PWD=/
SHLVL=1
SECURITYSESSIONID=ceb19270
_=/usr/bin/printenv
uid=0(root) gid=0(wheel) groups=0(wheel)
The script works much better when it can find the required programs. :0)
which netstat awk ping arp sed
/usr/sbin/netstat
/usr/local/bin/awk
/sbin/ping
/usr/sbin/arp
/usr/bin/sed
<pre style="border: 1px solid #ddd; padding-left: .75ex; padding-top: .25em; padding-bottom: .25em; margin-top: .5em; margin-bottom: .5em; margin-left: 1ex; max-width: 80ex; overflow: auto; font-size: 10px; font-family: Monaco, 'Courier New', Courier, monospace; color: #444; background: #eee; line-height: normal">get_route_mac() {
ip=$(/usr/sbin/netstat -nrfinet | /usr/local/bin/awk '/^default/{print $2; exit}')
[[ "$ip" = *.*.*.* ]] || return 1
[ ${1:-0} -gt 0 ] && /sbin/ping -nc$1 $ip 2>&1 >/dev/null
/usr/sbin/arp -n $ip | /usr/bin/sed -n 's/.* at (.*:.*:.*:.*:.*:.*) on .*/ /p'
}</pre>
Thanks for your help, Bob!

Manually Configuring CSRF filter in ADEP

Hello Folks,
I have installed the Document Services 10.0 in our development machine, which is a SUN sparc, Solaris based 64 bit machine. After the installation when I am trying to access the url as :-
http://<dev_server_name>com:9085/adminui
I am getting the below error in logs :-
[10/19/11 15:48:46:689 EDT] 00000030 CSRFFilter W Blocked request for resource:/adminui/login.faces due to invalid referer:http://<dev_server_name>com:9085/adminui/. More information is available at http://www.adobe.com/go/learn_lc_hardening_10
We do not have rights to install a browser on the unix box, and the only option is to set this up manually.
I want to know if there is a way to setup the white list manually, like by changing some DB property or may be changing some configuration file. Or may be during installation if I could specify this property in configuration manager ?
Any help would be greatly appreciated.
Thanks,
Amit.

I used Configuration Manager till it genereated the ear files in export directory. After that I deployed the ear's manually in admin console, also I created the data sources manually as defined in the installation pdf help document.
I deployed below ears in order as below :-
adobe-livecycle-native-websphere-sparc_sunos.ear
adobe-livecycle-websphere.ear
adobe-workspace-client.ear
After I deployed these ears, I did bootstrap the database using the below mentioned urls :-
http://<SERVER:PORT>/adobe-bootstrapper/bootstrap?responseType=client&bootstrapper=UM&step=bootst rap&host=aix.adobe.com&port=9080&responseLocale=en
http://<SERVER:PORT>/adobe-bootstrapper/bootstrap?responseType=client&bootstrapper=CORE&step=boot strap&host=aix.adobe.com&port=9080&responseLocale=en
http://<SERVER:PORT>/adobe-bootstrapper/bootstrap?responseType=client&bootstrapper=POF&step=boots trap&host=aix.adobe.com&port=9080&responseLocale=en
http://<SERVER:PORT>/adobe-bootstrapper/bootstrap?responseType=client&bootstrapper=DSC&step=boots trap&host=aix.adobe.com&port=9080&responseLocale=en
http://<SERVER:PORT>/adobe-bootstrapper/bootstrap?responseType=client&bootstrapper=TS&step=bootst rap&host=aix.adobe.com&port=9080&responseLocale=en
http://<SERVER:PORT>/adobe-bootstrapper/bootstrap?responseType=client&bootstrapper=WF&step=bootst rap&host=aix.adobe.com&port=9080&responseLocale=en
Not sure, what exactly I missed during install
There are 3 more ear's generated in the export directory of Configuration Manager, that I did not deploy yet, as they were not mentioned in the manual configuration section in pdf, these are as follows :-
adobe-forms-ivs-websphere.ear
adobe-assembler-ivs.ear
adobe-output-ivs-websphere.ear
Any ideas ?
Thanks,
Amit.

Manually configurable financial reports - table

Hello
Where do manually configurable financial reports are stored (table name)?

Hello.
If you are referring to FSG's you can look at RG_REPORTS table.
Octavio

How do you remove a manually configured wireless access point on the iphone 4S?

I have manually configured my iPhone 4s to point to a wireless access point that I no longer use. How do I delete it from the list of access points on my iPhone?

You can only "Forget this Network" while actually connected to the network, so ignore iamjeremi's post. Other than restoring your phone as a new device, you can't if you cannot connect to the network anymore.

LAP manual configuration

Similar Messages

Maybe you are looking for