Laserjet cp1025nw takes 90 seconds plus to start printing

How do I fix this?

Hi there,
This article should cover the issue you are experiencing. Give the steps outlined a shot and let us know if it helps.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

Similar Messages

How do i find a printer code of laserjet cp1025nw

My printer is LaserJet CP1025nw
How do I find my printer code ?
My product serial number is : CNBGC23476

Hi,
As of now, the ePrint feature is not supported for your printer.
you may find the supported printers listed below:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02814760&cc=us&dlc=en&lc=en&product=4083871&tmp...
As much as i know, your model should get an ePrint functionality with future firmware update, however i don't know of any estimated time for it.
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

How to configure ePrint on LaserJet CP1025nw Color Printer

Solution found:
How to Configure HP ePrint on the LaserJet CP1025nw Color Printer
System: Windows (Widows 7)
Step 1 – Install Printer
Install the CP1025nw Printer to USB, Wifi or Ethernet.
(Printer needs to print correctly in order to pass to the next steps).
Step2 – Check Firmware Version
Press the “Info-Button” on the CP1025nw LaserJet for five seconds.
The printer will print two info pages.
Look at the first Page on the top-left for Firmware Version
Firmware version must be 20120103 or higher.
Step 3 – Update Firmware
Download Firmware Update utility (LJCP1020_FWUpdate_signed.exe) from the following link:
Utilidad de actualización del firmware de HP LaserJet CP1025nw
or
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=lj-86491-5&cc=es&dlc=es&lc=es&...=
Execute the Utility on the computer were the CP1025nw LaserJet is correctly installed.
Find the CP1025nw Printer on the list. The selection Window might show the printer several times depending on how the printer was installed. Select one option and press the button “Update One”.
Step 4 – Retrieve the Printer Code for your CP1025nw Printer
ATTENTION:
The “Host Name” of the printer is not the “Printer-Code” you need for ePrint setup.
To retrieve the Printer-Code you must run the ePrint-Setup-Wizard-Utility.
To download of the utility, go to the link: http://www.hp.com/go/ePrint .
Find the “HP LaserJet Pro CP1020 Color Printer Series” option in the Drop-Down-List.
Click “Windows” to download the wizard (EPrintSetupWizard.exe ).
Execute the Wizard on the computer where the CP1025nw Printer is correctly installed. After running the wizard press the “Info-Button” on the CP1025nw LaserJet for five seconds. The printer will print three info pages. The third info-page offers the Printer-Code you need for ePrint setup. The code is valid for 24h only. When time elapses you have to reprint the info-pages to get an actualized Printer-Code.
Step 5 – Get Printer Email for your CP1025nw LaserJet
In order ePrint on your CP1025nw Printer you need to assign an email address to your Printer. To do this, go to the following link: http://www.hpeprintcenter.com/
Log in with your HP-ID. If you don’t have one, register for a new account.
When logged in, click on “Add new Printer”-button. You will be asked to enter the Printer-Code. (On how to get the Printer-Code, see step 4).
While evaluating the Printer-Code, be patient, the program needs its time.
When the Printer-Code is accepted, you can assign an email address for your CP102nw5 LaserJet. Done this, your con print your CP1025nw Printer just by sending the documents per email to the email-address of your printer.
Done.

Hi Max, check out the link below...
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?cc=us&lc=en&dlc=en&product=4052972
Hope this helps
Ciara
Although I am an HP employee, I am speaking for myself and not for HP.
Twitter: @Ciara_B_HP

LaserJet CP1025nw Printing Problem

Hi
I am running Windows 7 64 bit. I installed a new Laserjet CP1025nw a couple of months ago. I got everything working fine wirelessly as per the instructions. It has worked without problem since then ... until today.
Documents just sit in the print queue. They will not print.
Sending a test page wirelessly works fine.
Printing documents on an older wired Epson Inkjet printer I have attached works fine too.
I have tried connecting a USB cable again but cannot get it to print that way either. I have tried making it the default printer, and not. I have searched the support forum but been unable to find anything to help. I have used the Windows troubleshooting diagnostic but that seems to indicate everything should be okay. I have installed the HP diagnostic and that all tells me everything is okay.
Any help would be much appreciated.

I am the one with the Sony Vaio, Win 7 64bit, and have commented previouosly in this thread.
Now I have have taken the next step as per instructions from HP Support.
1. Delete HP Folder from Program Files and Program Files (x86). The latter was impossible to delete.
2. Do Run and run 'regedit'.
3. Make copy of present Registry using menu File and do export (as safety precaution)
4. Delete HP and Hewlett packard folders in the catalogues: HKEY_LOCAL_MACHINE\SOFTWARE\ and HKEY_CURRENT_USER\Software\, nothing else
After this I checked Control Panel , Start, and Task Manager and found some HP items still there. Did my utmost to erase them using Window delete functions, REVO and Registry Booster. hppcp1025LaserJetService (in Control Panel list) persisted along with some Services in Task Mgr.
Continuing according to HP Support instructions (but now with little hope only) I did
5. Re-installation of CP1025nw driver package: I choose the Basic option from the HP web which is supposed to be followed installation-wise by an update dated 2011-09-20 (Swedish version).
Results
a) after Basic installation, before update installation and before restart of PC: writing can be performed via the network, "Device settings" in Windows menu not available though
b) after Basic installation and update installation and before restart of PC: writing can NOT be performed via the network. Ping status not investigated
c) after Basic installation and update installation and before restart of PC: writng can not be performed via the network. Device settings via Windows and ping connection functions well though, although the printer is reported by Windows "Devices and printers" as off-line.
So now I may do a total recovery. There may be two outcomes after the recovery as I see it:
A. Printing goes well with the CP1025 via the network, also after installation of all necessary applications now residing on the PC (and which resided on the PC before this summer´s HP date)
B. Printing does not function with the CP1025 via the network, connections with other HP printers on the network also severely restricted (as today). Then the only conclusion would be incompatibility between HP 2011 drivers for the CP1025 and the Sony flavour of Win 7 64 bit Professional. And I would have to (again) claim the driver package as faulty.
The alternative would be to forget about the CP1025 already now.
Any suggestions?

My HP Color Laserjet CP 1215 recently started printing crooked.

My Printer at work, HP Color Laserjet CP1215 recently has started printing crooked. I have open all doors to check for anything stuck in the printer that could be causing it to print crooked.
Any suggestions would be greatly appreciated as I am not getting anywhere with what I have found on the website.
Tawnya Slagle

Hi Tawnya,
A couple of items come to mind that we can check:
1) Paper type/specs Make sure you're using recommended paper type for this product.
2) Remove, restack and reload and check paper guides in the tray to ensure the guides are against the paper and if available, restock with some fresh paper.
3) Have you recently experienced a paper jam? Were you able to remove the page intact? If not, there still may be a small piece of paper lodged in the printer causing the skew.
4) If the above steps don't resolve, I might recommend a calibration, steps listed below.
Best of luck!!
Follow these steps to calibrate the product.
Open Toolbox .
Windows XP: Click Start ( ), click All Programs , click HP , click your product, and then click HP Color LaserJet CP1210 Series Toolbox .
Windows Vista: Click the Windows icon ( ), click All Programs , click HP , click your product, and then click HP Color LaserJet CP1210 Series Toolbox .
Click the Device Settings folder, and then click the Print Quality page.
Under Print Quality , click Calibrate next to Calibrate Now .
Click OK when the 'Your request has been sent to the device ' message appears on the computer. The calibration process begins.
NOTE:Calibration might take 2 to 3 minutes. Do not turn the product off during calibration.
When calibration ends, try printing again.
If the issue is resolved, stop troubleshooting.
If you are still experiencing print quality issues, repeat steps 1 through 5 in this solution. You can recalibrate the printer as many as 3 times.
(Although I am employed by HP, I am speaking for myself and not for HP)
Say "Thanks" by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as "Accepted Solution"
I worked for HP but my posts and replies are my own....Thank you!
*Say thanks by clicking the *Kudos!* which is on the left*
*Make it easier for other people to find solutions, by marking my answer with (Accept as Solution) if it solves your issue.*

Lexmark C544DN network attached printer takes minutes to start printing job

I recently purchased a macbook pro 13" i am moving from a windows 7 environment. My network attached Lexmark C544DN takes up to 2 minutes to start printing the print job, it did not act this way under windows. I have gotten the latest firmware and drivers for the printer, from the Lexmark website, in attempt to figure out the problem. My network hub- router is an airport extreme. I have noticed that at times when surfing the internet safari pauses when loading the page, this appears to be random not associated with certain websites. Not sure if the two are related but since both are using network protocols one may have to do with the other.
I am looking for things to look into that may cause such a problem and how to look into them as I am fairly computer savvy but my experience with the Mac OS X 10.6.5 is limited to going on two weeks now.
I should probably mention that the Mac network is solo not a hybrid with windows and mac together.
Thanks for any advice that can be given on this problem.
tjhinmn

I am sorry, you are still on the consumer forums. To get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial printer. You can do this at Printers - LaserJet. Just click on the New Post button.
I hope this helps.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Set up wireless printing on LaserJet CP1025nw

All of a sudden, i can't print wirelessly. I'm running Yosemite 10.10.1 on MacBook Air (no ethernet connection). I've tried searching for an updated driver on HP but it just says to download it through Mac Software update. I've deleted the printer and readded the printer - to no avail. HELP!

Hi @kgarlich ,
I see that you are experiencing issues printing over the wireless network. I would like to help you out today.
The drivers are installed by the Apple Updates for this printer. Installing Your HP Printer Driver and Software for Mac OS X.
Check the driver name that is installed for the printer. Make sure it shows just the printer's name.
Click the Apple menu and then click System Preferences. Click Printers & Scanners, highlight the printer name on the left side and on the right side of the screen it should show the printer's name. ( LaserJet CP1025nw)
If the full printer name isn't listed correctly, delete it and add the printer name back in from the list. Click the - sign to delete the driver and then click the + sign to add the driver, might have to click the drop down to select the printer's name to add it in.
If you are still having issues, please try the following steps:
Repair the Disk Permissions on the Mac:
Close all applications.
On the Apple menu bar, click Go, click Applications and then click Utilities.
Double-click Disk Utility.
Highlight your hard drive/partition on the left.
Click Verify and then Repair Disk Permissions.
Restart the computer..
Reset the Printing System:
Note: This will remove all printers in the print and Fax/Scan, any printer removed can be re-added later by clicking the plus (+) symbol.
Click the Apple icon and then click System Preferences.
Click Printers & Scanners.
Right-click (or Ctrl +click) in the left white side panel, then click Reset printing system.
Click OK to confirm the reset.
Type the correct Name and Password.
Click OK to reset the printing system.
Then click the + sign to add the driver, highlight the printer. (you might have to click the drop down to select the printer's name) Then click on the Add button.
If the issue continues, let me know the outcome after doing the following steps:
Print a configuration page to get the printer's IPv4 address.
On the printer control panel, touch the Wireless icon (), and then touch Print Info.
If you have a valid IP address for the printer then try and access the Embedded Web Server for the printer.
Type the IP address into your web browser's address bar. (Safari)
Did it load the web page?
Check the IP address on the computer.
From the Apple Menu, select System Preferences, Network, select your currently active network in the left-pane.
Your IP address will show in the middle corner of the window.
The first 3 sets of numbers have to match the printer's first 3 sets of numbers to be on the same network.
Try and ping the printer.
On the Apple menu bar, click Go, then click Applications, then Network Utilities.
(you can go to the finder and type in Network Utilities)
Click on PING from the bar at the top of the window.
Enter the IPV4 Address of the printer and click Ping.
Did you get any replies back?
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Laserjet CP1025nw color, unable to change Print density

Hi,
I need to raise the "Print Density" to 5 (for pcb toner transfer) on my Laserjet
CP1025nw color, but when I open the printer properties I do not have that option
in the device settings tab, despite what is said on the help page of that model.
OS: Windows XP
The printer is on the USB port.
The pilot is: HP LaserJet Professional CP1020 Series + last update
How can I change that setting ?
Please help !!!
Thank you in advance for any help you can bring !
All the best,
This question was solved.
View Solution.

From what you describe you want to increase your toner density on your subsequent print jobs. First of all, if you have not, you should uninstall this printer and make sure that the drivers are the most up to date using the website I will link below :
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?cc=us&lc=en&dlc=en&product=4052972
Here you should also check for your firmware to be sure that it is up to date.
I would also, both before and after, check under "Printer Preferences" (not properties) and see if there is a way to change the density under the Paper/Quality tab.
Let me know if this helps you out!
-Spencer

My HP LaserJet CP1025nw won't print, "Filter failed" error

Whenever I print something, it acts like it's about to then a system notification just says "printing stopped." There is a "Filter failed" error at http://localhost:631/printers/HP-LaserJet-CP1025nw. I have hplip installed, and have reinstalled it a few times. Two things I've tried from searching the web. I cleared the pacman cache and still the same issue. I tried installing foo2zjs from the AUR, but it would not compile (did not pass the validity check). It prints fine on Linux Mint. I'm out of ideas and don't know where else to go. Any suggestions?

That page's troubleshooting for the "Filter failed" message worked out. I consulted the Wiki before but never found that exact page. I guess I didn't use the best search criteria. Thanks for pointing it out.

I need to connect my wireless printer (HP LaserJet CP1025nw color) to the internet.

I need to connect my wireless printer (HP LaserJet CP1025nw color) to the internet. I recently have changed my name and password of my modem. Since the change I have lost connectivity between my computer and my printer. What do I need to do to regain connectivity? I am using Windows 7.
Trydell

I think you mean your password on your router right? Changed your SSID and/or password?
Try here.
http://www.hp.com/global/au/en/wireless/reconfiguring-system-help3.html
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

My HP LaserJet 1018 has started printing only blank pages.

My HP LaserJet 1018 has started printing only blank pages.
Help?
Using Windows XP (Home Version)
Product # CB419A

Could be a number of issues. First could be a bad or not connecting transfer rollers which moves the toner from the drum to the paper. Only way to test is a half test by putting paper on the manual tray and printing a self test. When the back edge enters the printer, open the toner door to stop printing. Remove the toner and flip back the cover over the toner drum to see if there is any image on the drum. If image is present then it could be transfer roller issues. Use the service manual and look under engine diagnostics in the index and it will direct you to a page that shows how to perform an engine test. Do the test to see if you get a sheet of paper with lines on it. If you get lines, then the issue could be the formatter. If no lines and the shutter has been removed then I would think you are having high voltage issues. You may have to bring the printer in for service.

Why does it take 40 minutes to start watching a rental on Apple TV but only seconds to start watching Netflix?

Why does it take 40 minutes to start watching a rental on Apple TV but only seconds to start watching Netflix?

Welcome to the Apple Community.
The first thing to check would be your internet download speed, you can do this at www.speedtest.net.
HD movies require a recommended speed of 6 Mbps, while SD movies require a recommended speed of 2.5 Mbps.
Netflix movies are adaptive and vary their quality according to your connection and can be as low as 0.5 Mbps.
But remember lower datarates = lower quality.

Why does it take so long for my wireless printer to start printing from my MacBook?

Why does it take so long for my wireless printer (HP Photosmart C4700) to start printing from my MacBook?
It seems to take about 3 minutes to spool up printing from any program on my MacBook, but it will start instantly with my iPhone.

Anyone have any insight on this?

I cannot get my HP Officejet 6500A Plus 710N to print in color. I have reinstalled the drivers..

I cannot get my HP Officejet 6500A Plus 710N to print in color. I have reinstalled the drivers. It used to print in color and just stopped. I think it may be a settings issue? I have checked the ink levels and they are all fine. When I print a diagnostic report on print qualify, the black prints well, but there is no color printing.

Okay, I had the same problem. It's most likely your printhead. All you have to due is clean it.
Note: I was sceptical of this approach but can fully attest to it's sound results as it restored my printer back to full functionality. Prior to this the printer only would print Black ink.
The print head is the carriage that holds all of your ink cartridges in the printer. On the 6500A it's super easy to remove. Opent your lid like your changing your ink cartridges. Remove all of your ink cartridges. Once they're out. There is a lever on the left side of the carrier that holdes your ink cartridges. Lift it up and the print head comes right out. Net take your print head to the sink and run it under hot water aiming towards the the four cirles were the ink flows into. Keep running it under the hot water until it is coming out clear. It's okay to run it under the bottom part too infact you'll need to inorder to get it completely rinsed out. Also don't touch the computer metal strips with your hand thought you can run water over them. Once your done rinsing use a blow dryer or a can of compressed air (thats what I did) to dry every thing out. I was able to get everything dry in about 5 minutes or so. Let it sit for a few minutes and check it again for water. I recommend moving it around to get full exposure to insure it is dry. Also if you use a hair dryer try to put it on a cold setting since there ar rubber grommets the surrount the inlet ink ports you wouldn't want to melt them with the hot air etc.. Like I said I used a can of compressed air. It's important to use a quick method of drying as mentioned otherwise mineral particles could become deposited on the unit. This won't happen with the methods as I've described because the molecules won't be able to bond since your blowint them off. Oh yeah, you'll want to place a clean peice of paper down as your blowing because at first you'll end up with a few black jet marks as your blowing. Also don't wear your favorite white shirt lol.
Okay once it's dry replace the print head carriage back in push the lever down install the ink cartridges. Close the lid then unplug the printer. Wait 5 seconds plug it back in then it will reboot and start its set up procedure kind of like whet you first bought the printer except you won't have to change any of your network or setup setting since they are saved in memory. Also be patient about the set up procedure it seemed very slow for me. Once it finishes you will be prompted to run the printer alignment process. Run the alignment process and you should be all good. If not at least you gave it a shot. If this doesn't work your going to have to pay $60 for a new printer head. Which is not that big of a deal but hey if you can fix it for free why not. If you do decide to buy a new printer head you might find deals online or ebay just make sure it's an Genuine HP print head. And lol use the Genuine HP ink cartridges. Finally make sure you print at least on colored page per month to make sure the ink doesn't clog up in the future.
Remember this suggestion is after you have run the HP clean ink cartridge procedure twice. Sometimes the clean procedure will correct the problem first. Also there is video I watched on YouTube about this just search for "Clean HP 6500 print head. Hope that helps
Once it's all dry just reinstall the printer head carriage

HP LaserJet CP1025nw Color getting a Mispick error message

I have a HP LaserJet CP1025nw Color printer, running on WIN 7 64-bit and I am getting a Mispick error message after almost every page that prints. I have had this printer for the past 1-1/2 years and it has worked fine. I replaced the black toner over a month ago with no issues. The Attention light blinks and has to be rest after each print job. I can print a test page then it errors, I clear it and then it will re-print the test page again. I have cleaned the rollers, check for any loose paper pieces, changed the paper (type and size) nad have powered off & unplugged the power to the printer several times. It will come up with no errors and then once I send something to print, it will print it and then immediately after the page is printed the Attention light will start to blink. I have even gone as far as unintsalling the printer and reinstalling all the drivers and software, to no avail.
Any help would be greatly appreciated.
Thank you,
Jarm1964

This is probably a little late but it may help someone with the same issue in the future. I had the exact same scenario - HP LJ CP1025nw color on Win7-64 and it suddenly started receiving the mispick error after every print job. There was nothing stuck, no paper jam, no problem picking up paper, etc. It turns out it was a setting on the printer - under Printer Properties (from Devices and Printers), on the Configure tab I had checked Allow Manual Duplexing and Jam Recovery set to On. When I unchecked Allow Manual Duplex and turned Jam Recovery to Off, the mispick error went away. Not sure which of the 2 was the culprit.

Laserjet cp1025nw takes 90 seconds plus to start printing

Similar Messages

Maybe you are looking for