Led On/Off .control

Hi Folks.
I am having trouble keeping certain Led's on at certain times. The power on and off turn eachother on and off as required. However when I press any of the other buttons the Power On/Off Led goes off. I have set up an event structure to handle the different button presses. Is there a way to keep the current value when the other buttons are pressed?
Also but not very important now. Is there a way to implement the led's in the actual buttons themselves without having to use extra components?
Thanks,
Mark.
Attachments:
Lifetemp Programming and Testing.vi ‏30 KB

MarkGreally wrote:
The problem with this is that I need the On button to turn the Off Led off and vica versa. I need off and on to influence on another. 
My comment was just to note that there is another solution after what paul_cardinale mentioned if you don't need mutliple event cases to interact with the indicator(s).
MarkGreally wrote:
Is it possible to set them up to hold previous value if unwired or something like thta?
No, but you can store values in memory in places other than indicators.  The While Loop structure supports a shift register for this.
A common solution to your situation is to save state information on a shift register of the loop and update indicators from that.  For example:

Similar Messages

  • AppleTV (2nd gen) working fine but LED is off

    My Apple TV (2nd gen) is working fine but today the white LED is off.
    I tried to disconnect from the electricity but it doesn't helped. I also made a restored to factory settings but it is still off.
    Yesteday I used at night to watch a movie and the LED was on, I woke up and went to work, when I tried to work today I noticed the LED was off.
    As I said everything works fine but the LED.
    Any ideia?

    I have the same issue my aple tv works fine but the led is off. I also tried to restore and update without success....
    Any idea or real problem ?
    Cheers

  • IMac 20" won't start.  l led 1 is on, but led2 flashes, led 3 off. Why?

    My wife's original iMac 20" suddenly today went fans full on. She turned it off by holding the on/off button for some time. Now it won't start up. With the back off led 1 if on, and led 2 is flashing. I've found reference to led 2 off and led 2 on, but not flashing. I've reset the SMU several times and the led went off, but after several seconds started flashing again. Can anyone suggest why?

    It's likely that your power supply has failed, but ake sure that there is no dust clogging the fans or vents.

  • Please add LED turn OFF option for DL2100

    If there is an option for LED turn off on EX2, why can't it be on DL2100, since it's basically the same OS ?Please add this option on this device, thank you !

    Hi Rahul,
    Which release of Oracle Applications are you on?
    Regards,
    Mohammed

  • Why the network link LED always off for all B200 blade servers? is it normal or heathy?

    Hi Expert,
    Why the network link LED always off for all B200 blade servers? is it normal or heathy? refer to the installation document, it means no active network connection. However, all these servers are up and running with netwirk connection. anyone could explain this?

    Hi Tabish,
    How many times do you have to open this same topic?
    In my opinion, this is your THIRD thread for the same topic.

  • Satellite L750 - network card on, Led ligth off

    Hello.
    Satellite L750 -> Laptop network card connects internet but led light off ?
    Thanks

    Thanks Jacky,
    +What network card and what LED indicator do you mean exactly?+
    Network card, RJ45 port (i think it's atheros ethernet gigabit)
    +Do you mean WLan card and WLan indicator?+
    NO, no Wifi. Lan card, and Lan indicator on RJ45 port
    +Are you using Toshiba preinstalled system?+
    Yes
    I have internet connection on RJ45 port (cable) but the Lan indicator is OFF
    Thanks

  • My Led flash light switch on all the time,anybody got the solution.i tried 3 things but it couldn't solved the problem. 1.settings-accessibility-LEd flash off   2. Switch off the phone for several times.  3.press the home button n power button until the

    My Led flash light switch on all the time,anybody got the solution.i tried 4 things but it couldn't solved the problem. 1.settings-accessibility-LEd flash off   2. Switch off the phone for several times.  3.press the home button n power button until the apple logo appears.  4.reset my all settings.

    My Led flash light switch on all the time,anybody got the solution.i tried 4 things but it couldn't solved the problem. 1.settings-accessibility-LEd flash off   2. Switch off the phone for several times.  3.press the home button n power button until the apple logo appears.  4.reset my all settings.

  • Power & Wireless LEDs turn off on WRT54GX2

    Over the past week, this has happened 6 times: the power and wireless LEDs turn off, the ethernet(1) and internet LEDs flicker like mad.  While it's like that, all LAN and WAN traffic is disabled.  It is connected to a DSL modem and the LEDs there appear normal.  If I cycle power on the router, it returns to normal.  I have not yet connected this behavior to any special events on my LAN.  Does anyone have a suggestion?

    You should Upgrade your router's firmware...
    Download Firmware 3.70 MB...Firmware Ver.1.01.22...
    Follow these steps to upgrade the firmware on the device : -
    Open an Internet Explorer browser page on a computer hard wired to the router...
    In the address bar type - 192.168.1.1...Leave the Username blank & in Password use admin in lower case...
    Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
    Wait for few seconds until it shows that "Upgrade is successful"  After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
    Now reset your router :
    Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
    If your Internet Service Providor is Cable follow this link
    If your Internet Service Providor is DSL follow this link

  • Switch off Controlling Documents

    Can any body tell me how to switch off Controlling Documents.
    Because our requirment is when there is any invetory positing system should not created Controlling Documents.
    Thanks in advance,
    Murali

    don't create the GL accounts that the inventory movements are posting to as costing elements. you won't get any CO documents then.

  • All of a sudden, the radio signal LEDs went off and node went dead

     In order to change the I/O variable data type of my node from single to array of single, I simply press and hold the rest button on WSN-3202 for 7seconds. At the end of it, the radio signal LEDs went off and node went dead. All attempt to bring it back to life proof abortive. What should I do?
    Blessing

    Hi Blessing,
    If you've tried everything to get it working, including a fresh set of batteries or direct power from an adaptor, then you should contact your local NI branch regarding the repair process. The contact information for your branch can be found on http://sine.ni.com/apps/utf8/nicc.call_me.
    Regards,
    Imtiaz Chowdhury
    Head of Digital Technologies
    Brand786

  • Small PID output range causes on/off control only

    I am using the PID VI to control the signal to a heater in a refrigeration test rig. When I set the output range to 4-20 (representing 4 to 20 milliamps) it seems to control OK. However, for a new device, the range must be set in amps not milliamps, and I find that when I set the output range to 0.004 to 0.02, I only get on/off control. In other words, when the process variable exceeds the setpoint by even the smallest amount, I get 0.004, and when it is less than the process variable, I get 0.02. There is no in-between.
    Can anyone please explain this to me. Coupled with this, can anyone point me to a decent document that describes how this PID VI should be set up and used. I can obviously work around the problem by setting the output range to 4-20 and then divide this number by a thousand before feeding it into the output DAQ card, but I find the whole thing very confusing. I thought by having settable output ranges, the PID program would scale these values for you.
    Regards,
    Will

    The PID Control Toolset User Manual can be found here.
    http://digital.ni.com/manuals.nsf/websearch/A25258DF0D3E3CB386256B41000BA9B9
    If I read page 2-1 correctly,
     reducing your "P" value by a factor of 1000 should do the trick.
    Ben
    Message Edited by Ben on 05-03-2006 12:27 PM
    Ben Rayner
    I am currently active on.. MainStream Preppers
    Rayner's Ridge is under construction
    Attachments:
    PID_Operation.JPG ‏18 KB

  • When Entering Sleep My Pc Led Turns Off

    when i had upgrade my pc with a gpu my sleep option was gone and if i click the power button it looks like my pc turns off but when i turn it back on it just wakes up my gpu is xfx radeon 6670

    Hello , I understand that your desktop computer's LED turns off after you upgraded the graphics card, and I would be happy to assist you in this matter! To correct this issue, I recommend following the steps in this document on Troubleshooting Sleep and Hibernate Issues (Windows 8). If the computer is still experiencing issues with sleep and hibernation options, I recommend following the steps below to reset it's power settings: Step 1. Click the Start button
    Step 2. In the search box, type "Command Prompt"
    Step 3. Right-click Command PromptStep 4. Click Run as administrator
    Step 5. At the command prompt, type powercfg /restoredefaultschemes and press Enter  reference: http://superuser.com/questions/669571/windows-8-1-64-bit-power-schemes-gone I will also need to know if this issue occurs if you remove the graphics card, and run the computer using the integrated GPU. Please re-post with the results of your troubleshooting, as well as the requested information above. I look forward to your reply!
    Regards

  • Power LED Turns Off and pc Hangs

    Hi,
    During the last few weeks i've been having some problems with my system.
    1. While playing games at a certain time (not always the same time) my power led turns off but my system does not turn off. Instead it just runs very slow and any audio, software and the mouse pointer is constantly lagging until i restart it.
    2. After problem 1 while restarting it takes a lot of time to shutdown and hangs at the Windows is Shutting Down screen, so then i'll have to press the reset button.
    3. The system also rarely instantly turns of without going trough shutdown and even more rarely it resets while scanning the RAM at the BIOS.
    Thanks in advance for all your help!
    Specs:
    MainBoard: 865PE/G Neo 2
    CPU: Intel Pentium 4 Prescott 3Ghz
    Memory: 512MB DDR (x2)
    PSU: 650W
    Graphics Card: GeForce FX 5200 128MB
    Sound Card: 5.1 Channels Onboard
    Ethernet: 1GB Onboard
    Hard Drives: IDE 80GB and SATA 160GB
    Optical Drives: DVD and CD writer
    Other: 3.5 inch Floppy and SD card reader.

    Yeah well my PSU is ok cause i just baught a new one and i hope i dont have a short.
    Do you think that maybe the graphic card isnt compatable or something cause these things started happening when i changed my graphic card and this only happens while i'm playing games cause not even if i have loads of software running it still wont do it.
    And does anyone know of software which i can use to check my RAM?
    Thanks.

  • How do I turn off controls in the mini player?

    Hello, I have a question about the mini player. When I first installed iTunes, the mini player would only display the control icons when I moved the cusor over the player, with only the artwork displayed while the player was in use. Now, however, every time I use the mini player it always has the contorls on display. Is there a way to toggle the controls on and off so that they are only visible when I want them to be? For reference, the mini player always looks as it does below. When I first began using it only the artwork would be on display. I've tried reinstalling iTunes, but the player still looks the same (I did not do a full uninstall/reinstall however). Thanks for any help or suggestions.

    Hello moeszyslak,
    I would recommend testing to see if the issue is system wide, or user specific as the troubleshooting for each is different. Use this article:
    iTunes for Windows Vista or Windows 7: Troubleshooting unexpected quits, freezes, or launch issues
    http://support.apple.com/kb/ts1717.
    Create a New User Account
    When troubleshooting a variety of issues, it can be useful to determine if the issue affects a specific Windows user account or all accounts. Follow the steps below to create a new user account in Windows Vista or Windows 7:
    From the Start menu, choose Control Panel.
    Open Add or remove user accounts (If using the Classic View in Windows Vista, open User Accounts. Then open Manage another account).
    Select Create a new account and follow the instructions to complete the account setup process.
    Once the new account is created, choose     Log Off from the     Start menu.
    Log into the newly created user account.
    Open iTunes and determine whether the issue you were experiencing persists in this new user.
    If you see the same issue in the newly created user account, proceed to the System-wide troubleshootingsection below. If you do not experience the same issue, consult the User-specific troubleshooting section below.
    User-specific troubleshooting
    System-wide troubleshooting
    All the very best,
    Sterling

  • Computer does not turn on, power LED goes off when power button is pressed

    My Pavilion 17-e078nr has stopped working, it will not power on. When you push the power button, the power LED next to where the plug is goes off and takes several minutes before it comes back on. I've tried removing the battery and get the same results and with the batter in and AC disconnected the power button does nothing. I've also tried the hard reset with no luck. As far as I know, nothing has happened to the computer since last time it worked. My two theories are either the AC power is bad, or there is a problem internal to the laptop. The AC power is providing the 19.5V, I measured it using a multi meter, I'm just not sure if it's providing the required wattage, or if the connection to the laptop is secure, it feels a little loose, but at the same time the LED comes on, so I know it's getting a connection. Only thing I can think to try is go to a store that sells this type of computer and see if I can use one of their power supplies to power my computer, and/or plug my supply into one of their computers. Don't know how willing any store would be to allow me to do that though. Any one have any additional thoughts or advise?

    Hi! I have the exact same problem... the LED on adapter, is very, very dim when connected.
    At first I tried connecting my macbook to my roommate's adapter and had the same problem. then tried taking out the battery, and still had the same problem. I did the same thing with my roommate's macbook, but hers did actually turn on! it operated without the battery. Figured out it was problem with mine.
    I kept on trying combinations battery, computer and adapter. turns our that my battery (which I thought at first was the problem) charges perfectly on my roommates mac, but wont charge on mine. her adapter won't work either on my computer. What I've been doing is charging my battery on her computer, then placing it on my mac, and it works. only thing that won't work is the adapter.
    Went to a mac store, and they told me that the problem was a small cable o wire that went from the Magsafe point into the mac and that the LED was very dim because no energy was being drawn from that spot because of this little wire being broken. they gave me the name of this wire... very technical stuff so, completely forgot cause I didn't have anything near to write on.
    I'd like to know if anyone has gone through this same ordeal, and had this wire replaced without any problems. When it comes to opening up my mac, I'm a bit skeptical, since warranty is expired and wouldn't want for a solution to become a bigger problem.

Maybe you are looking for