Lenovo ThinkPad X131e Replacement Hard Disk Drive Specifications

I have recently been given a Lenovo ThinkPad X131e 3368-2GU. I notice that the internal 320GB 2.5" SATA Seagate Momentus Thin HDD is a slim height 7mm model. I would like to upgrade internal storage to 1TB or more. Do I have to replace this HDD with another 7mm model or will any 2.5" SATA HDD work? Any other replacement HDD requirements of which I should be aware?
Thanks for any assistance!
Solved!
Go to Solution.

Tryed by myself , the 9.5mm doesn't fit , 7mm works perfectly

Similar Messages

Replacing hard disk drive

hi,
i need to replace the hard disk drive inside my powerbook 12-inch (g4)... any suggestions on where i can get a good deal on a replacement hard drive? also, a good step by step guide on how to replace the hard disk drive
thanks!
matt

Matthew:
Indicating your location in your Public Profile makes it easier for those who respond to your queries. In addition, identifying your computr by processor speed will also be helpful.
Your computer will support a 2.5" Parallel ATA/IDE Hard Disk Drive. Here is a list of available drives. Use the filters in the sidebar to screen for capacity and manufacturer etc. then select and compare drives, or select the drive you like and Compare prices.
cornelius

Hard Disk Drive Specification in Bios

In standard CMOS Feratures in the Bios, you can manually input the Hard drive configuration and specification. On my two PATA disks, all of the options like are present, but when I select my SATA Hitachi 7K250 160GB drive only the Type and Maximum Capacity are present. There is no way I can enable 32 Bit Transfer Mode at all. I was just wondering if this is a BIOS problem or the BIOS just does this thing when a SATA drive is installed.

Quote
Originally posted by Raven
from what i heard microsoft drivers run over bios settings on pata drivers and i can think the same goes for sata.
What do you mean "run over"? Is it similar to Bios not being able to detect the capacity of drives larger than 137GB w/out Service Pack 1?

Upgrading Hard Disk Drive of Lenovo THINKPAD T500 2055 ?

Hi there,
My personal laptop is Lenovo THINKPAD T500 2055, and its main specifications as follows:
- Intel Core 2 Duo processor T9400 (2.53GHz 1066MHz 6MBL2).
- 8 GB DDR3 SDRAM Memory Module 4 GB (2 x 4 GB) 1066MHz DDR31066/PC38500 DDR3 SDRAM SoDIMM Kingston
- ATI Mobility Radeon 3650 with 256MB.
- 160 GB Hard Disk Drive, 7200rpm.
I really need to upgrade the Hard Disk Drive to a bigger size (500 GB, 7200 rpm). and, my major questions are as follows:
* Could you please advise me on which Hard Disk Drive (500 GB, 7200 rpm) should I buy for my T500 laptop?
For example, I found (http://www.amazon.com/gp/product/B003NSBF32) But I have no idea what T500 supports and what it doesn't... Therefore, I need your help to guide me about this matter. In other words, How do you know if ABC-Hard Disk Drive fits with T500 and XYZ-Hard Disk Drive doesnt fit? What is the clue in knowing what T500 accepts?
My another question is:
* How easy is it to remove/replace Hard Disk Drive in Lenovo ThinkPad T500 ???
I already watched CRU Removals/Replacements on (http://www.lenovoservicetraining.com/ion/R61_T61/index.html), But the clip is for ThinkPad R61 and T61. So, Could you please help me how to handle it with T500 ?
I would greatly appreciate your inputs.
Thanks for your consideration of my request, and I very much look forward to hearing from you soon !
Solved!
Go to Solution.

Hi and welcome to the forum!
Any SATA drive that is 2.5'' wide and 9.5mm high will work in your T500. The drive you linked to meets the requirement and thus will work.
For removal and installation instructions, have a look here:- http://www-307.ibm.com/pc/support/site.wss/migr-71568.html
Hope this helps.
Maliha (I don't work for lenovo)
ThinkPads:- T400[Win 7], T60[Win 7], IBM 240[Win XP]
IdeaPad: U350
Apple:- Macbook Air [Snow Leopard]
Did someone help you today? Compliment them with a Kudos!
Was your question answered today? Mark it as an Accepted Solution!
Lenovo Deutsche Community Lenovo Comunidad en Español
Visit my YouTube Channel

D20 hard disk drive caddy part number?

I';m trying to order a couple of replacement hard disk drive caddy for my D20 as one has split at the handle and another looks like it is about to go.
Does anyone know what the FRU part number is for these? The part I need is the toolless black plastic carrier for 3.5" hard drives.
Thanks very much!
ThinkStations: D10, D20, and S20
ThinkCentres: S50, M51, A61e
ThinkPads: W520, X60T and X61T SXGA+ tablets
Solved!
Go to Solution.

FRU # 41R5630 should get you one or two. if you still need them, i might have a spare kicking around somewhere.
http://www.ibm.com/shop/us/maintenanceparts or 800-388-7080 options 2:1:1 (unless the menu hierarchy has changed).
ThinkStation C20
ThinkPad X1C · X220 · X60T · s30 · 600

Hard disk drive replaicement

I have a Hard Disk 1 (301) error message, when turning on my laptop. It says something along the lines of "the hard disk has detected an imminent failure".
My laptop is a HP Pavilion G7-1033cl (windows 7), purchased in 2011, so it's out of warranty.
As far as a noticed in some other answers, I shoul replace the hard-disk for sure.
Ok, my question is: What kind of hard disk shoul I buy for replacing it? What's the best recommended?
Thank you for your help!
GStoicu

Whenever the Hard Disk fails with an error Hard Disk 1 [301] that indicates that the Hard Disk Drive has failed and that requires a replacement to resolve the issue
This issue could be due to Application or driver conflicts, virus issues, file corruptions due to incompatible applications, improper shutdowns, update failures due to conflicts, sudden power surges, if notebook is dropped etc..
HP will provide a replacement Hard Disk Drive if the Notebook warranty is Active, If not you need buy a SATA Hard Disk Drive from a retail shop nearby
Please make sure you are getting at least equal capacity as the original one in order to use Recovery Disks. If you need you can buy a larger, but not smaller capacity Hard Disk Drive. For example if you have a 500GB Hard Disk Drive you can upgrade it to 750GB Hard Disk Drive but not 320GB Hard Disk Drive
Please try the below shown troubleshooting steps once:
Step 01. Remove the battery and unplug the AC/Power Adapter
Step 02. Press and hold the Power button for more than 30 Seconds
Step 03. Plug in the AC/Power Adapter (leave the Battery out for now)
Step 04. Press the Power button and check if the Unit works normal
If the above mentioned steps does not help, then you can try reseating the Hard Drive on your Notebook
If the issue persists again please Contact HP if your HP Notebook is under warranty, HP would replace the Hard Disk Drive and provide you a Recovery media to restore factory operating system after replacement (if you've not yet created Recovery Discs/USB Media)
Note: Back up all the personal data to an external drive if it's possible. Otherwise you could connect the failed HDD via SATA to USB adapter with another PC or same PC after replacement of HDD & re-installation of OS and try copying /recovering the files. You can also refer to the below shown link for further support
http://www.wikihow.com/Recover-Data-from-the-Hard-Drive-of-a-Dead-Laptop
Please click on the link In order to Identify, Prevent, Diagnose & Recover from Drive Failures on HP Notebook Hard Drives & Solid State Drives :
http://h10032.www1.hp.com/ctg/Manual/c02876562.pdf
You can Check your warranty Here to verify the status and Click Here to order a new Hard Drive
Hope this helps, for any further queries reply to the post and feel free to join us again
**Click the KUDOS star on left to say Thanks**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
Thank You,
K N R K
Although I am an HP employee, I am speaking for myself and not for HP

Just bought a Lenovo 3000 N200 without a hard disk drive, need software

I just bought a Lenovo 3000 N200 Type 0769-BLG assembly date 07/09 from e-bay, it looks brand new but it had a fault, it was dead, perhaps a faulty motherboard and the hard disk drive had been removed. Assuming I can get the fault fixed, where can I get the Lenovo software that came with the original hard disk drive, I would prefer a free source, if that is possible, perhaps some kind person has put all of the CD's on to a DVD that I can borrow or buy a copy of. I was an IBM employee for 30 years before retiring 15 years ago. Dan McLean in Scotland, UK.

Call customer service directly to get a quick solution for this.
IPnaSh
First Spanish Community Guru - Colaborador ad honorem

Replacing SSD with hard disk drive on Qosmio X505-Q880

Is it possible to replace the SSD drive in a Qosmio X505-Q880 with a hard disk drive? If so what type will work?
Thanks,
Ed

Yes. I just replaced my 60 gig with a Kingston 240gig from Amazon. Re installed Windows 7 Ultimate. I DID NOT use the recovery disk from Toshiba because there were many programs that did not suit my needs, excellent though they were. It runs very fast about 4 times as fast as my old drive.

Satellite A10 S213 replacement of Hard Disk Drive

My Satellite A10 S213 is equipped with a Hard Disk Drive MK4021GAS HDD2182 B ZE01 S (40 GB) . The Disk is making more and more often loud and strange noises although it works well.
But it will certainly not go on for long.
I would like to replace the Disk Drive with something compatible and if possible with more capacity. Around 100 GB would be fine .
So my question is :
*Does a replacement of the HDD MK4021GAS HDD2182 B ZE01 S with more capacity exist for the Satellite A10 S213 ?*
Thank you for your help.
gh246

Hi
I assume your notebook supports the IDE HDD controller.
Possibly the IDE HDD controller supports only the 28bit LBA which would allows you to use max 120GB HDD.
I think you could install an bigger HDD.

Can a T60 (with completely zero-ed hard disk) install a hard disk drive from a CD? Or floppy only?

Hi
Yikes - I am in deep trouble !
Following a virus attack, I have zero-ed my Thinkpad T60's hard disk (using KillDisk), but now when I try to install WindowsXP Pro from a CD, but although it can read the CD and does get so far... it says it cant read the hard disk !
I was hoping to install the correct driver (see below) but now I can't find my floppy disk drive for my T60.
Is it possible for DOS to read off a DVD or a CD?
I have tried to download a file which I am hoping is the correct driver
"Intel Matrix Storage Manager Driver for Windows 7 (32-bit), Vista (32-bit) and XP (32-bit) - ThinkPad"
6iim10ww.exe
www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-70477
But without a floppy drive I dont know how to get it into my T60!
Is it possible to put the data onto a CD or a DVD and read from there?
Cheers
Ship
P.S. My machine is a Lenovo/IMB Thinkpad T60 "2007-F4G" with a 74GB hard disk.
http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-62928#hdd

Hi shiphen,
please refer to this install instructions.
For further guidance check into this thread.
Follow @LenovoForums on Twitter! Try the forum search, before first posting: Forum Search Option
Please insert your type, model (not S/N) number and used OS in your posts.
I´m a volunteer here using New X1 Carbon, ThinkPad Yoga, Yoga 11s, Yoga 13, T430s,T510, X220t, IdeaCentre B540.
TIP: If your computer runs satisfactorily now, it may not be necessary to update the system.
English Community Deutsche Community Comunidad en Español

Arch: Install to & run from External USB Hard Disk Drive (HDD)

I wanted to play with ArchLinux 2009.02, but replacing the existing Debian-Lenny on the laptop's HDD wasn't an option. So I experimented with installing Arch on an external USB Hard Disk Drive.
I have tried to make this "newbie-friendly", so I hope the more experienced will forgive the detail.
Materials:
Three year old Dell Inspiron 6000
CPU = 2.0 GHz Pentium
RAM = 2.0 GB
Internal HDD = 80 GB
Internal CD/DVD R/RW
External USB HDD = Freecom FHD-2 Pro 80 GB
Archlinux 2009.02 install CD
Steps to install:
1. I put the Archlinux install CD in the drive and connected the external 80 GB HDD in the USB port.
2. When the Dell laptop was booted, I pressed F2 to enter the BIOS setup. I edited the boot sequence to the following:
Internal CD/DVD
External USB device
Internal HDD
On the Dell, you can also press F12 to select the preferred boot device for that boot.
3. I started the laptop and the Archlinux installation menu came up and I proceeded with installation following the "Official Arch Linux Install Guide" and the "Beginners Guide".
4. Used km to change to UK keyboard layout and then began the installer script (/arch/setup). I was installing from the core CD so I skipped the network steps.
5. HDD preparation.
This was fairly straightforward with two cautions:
(a) Make very sure that the external HDD (sdb) is selected for the operations.
(b) Remember to set the Bootable Flag for the first (/) partition on the HDD.
I chose 20 GB for /, 2 GB for swap and the remainder for /home.
6. The package selection and installation was fairly straightforward.
7. Configuration of System
This was section was straightforward with one warning:
USB had to be added to the HOOKS in the /etc/mkinitcpio.conf file!
I found this to be essential for my external USB HDD to function as a bootable device. Otherwise I got the same sorts of errors relating to unrecognisable file system types that other people have reported in the forum.
The relevant line from the end of the edited /etc/mkinitcpio.conf file is below:
HOOKS="base udev autodetect pata scsi sata usb filesystems"
8. Installation of GRUB was the other point where caution and/or correction was necessary.
When it asked where GRUB should be installed, I had to select sdb (my external USB HDD) and not any of the particular partitions on sdb. If the root partition sdb1 was selected then the laptop won't boot from the external USB HDD.
The GRUB /boot/grub/menu.lst as written by the installation routine specifies hd(1,0) which doesn't work when you try to reboot from the external USB HDD. When you boot Arch from the external USB HDD, as far as Arch is concerned - at that point in time - the external USB HDD is the first drive in the system. To fix this:
(a) When the Arch boot menu comes up, press e to edit the grub entries.
(b) Change the first line to hd(0,0)
(c) To the end of the kernel line add rootdelay=8
(d) Press b to boot the system with these temporary corrections.
(e) Once your Arch system has booted, edit the /boot/grub/menu.lst to make the above changes permanent.
The relevant portion of my /boot/grub/menu.lst looks like the following:
# (0) Arch Linux
title Arch Linux
root (hd0,0)
kernel /boot/vmlinuz26 root=/dev/disk/by-uuid/... ro rootdelay=8
initrd /boot/kernel26.img
# (1) Arch Linux
title Arch Linux Fallback
root (hd0,0)
kernel /boot/vmlinuz26 root=/dev/disk/by-uuid/... ro rootdelay=8
initrd /boot/kernel26-fallback.img
9. The laptop happily and consistently boots Arch Linux from the external USB HDD when it's plugged in before startup/booting.
Running Arch from the external USB HDD seems as quick as running Debian from the internal HDD.
So if there is a performance penalty associated with using an external USB HDD, my wife and I haven't noticed.
In summary, the three essential points to address during installation to an external USB HDD are:
Remember to set the bootable flag for the first partition.
Add USB to the HOOKS for /etc/mkinitcpio.conf file.
Correct the /etc/grub/menu.lst file.
I hope this is helpful.
Ted

Hi Rookie,
As you say, it is worth remembering the rootfstype= option for the kernel line just in case someone still has problems with GRUB after making all the other changes.
I was working with the most recent Arch 2009.2 release.
I only got messages about unrecognisable file system type when I tried booting with the "stock" or "as-installed" GRUB (before I edited /boot/grub/menu.lst). After editing /boot/grub/menu.lst to identify the drive correctly and add rootdelay, GRUB was able to do the rest and everything worked OK without any error messages.
Best wishes,
Ted

How does one SUCCESSFULLY transfer Time-Machine backup to a new (larger) hard disk drive using OSX 10.5.8

I have read a number of articles about how to transfer a complete Time-Machine backup to a new (larger) hard disk-drive. Some of these articles are specifically for OSX10.6 users, which are not applicable to me since I am operating with OSX 10.5.8.
However, I have tried several times to use the Disk Utility 'Restore' function, dragging my old time-machine volume into the 'Source:' box and my new volume into the 'Destination:' box. This works, of sorts, BUT the newly created volume on the new larger hard disk-drive remains the same size as the original volume on the old Time-Machine HDD, with no apparent way of increasing the new volume's size. So I am not really any better off:
E.g. the total capacity of my new HDD is stated by 'Disk Utility' to be 465.8 GB, of which I'm told 228.2 GB is used for the Backups.backdb folder, but only 4.6 GB of free space is actually available. Yet under the 'Partition' tab of 'Disk Utility' it tells me that there is still 236.4 GB of available space.
Does anyone know how to resolve this issue without upgrading to OSX 10.6?

First, how did you prepare your new drive? See:
Drive Preparation
1. Open Disk Utility in your Utilities folder. If you need to reformat your startup volume, then you must boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID (for Intel Macs) or APM (for PPC Macs) then click on the OK button. Click on the Partition button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
If you plan to partition this new drive then be sure you create a larger partition for TM than your old volume.
Next, clone your old TM volume:
Clone using Restore Option of Disk Utility
1. Open Disk Utility from the Utilities folder.
2. Select the destination volume from the left side list.
3. Click on the Restore tab in the DU main window.
4.Check the box labeled Erase destination.
5. Select the destination volume from the left side list and drag it to the Destination entry field.
6. Select the source volume from the left side list and drag it to the Source entry field.
7. Double-check you got it right, then click on the Restore button.
Destination means the external backup drive. Source means the internal startup drive.

DV9925nr - How to Backup Hard Disk Drive After S.M.A.R.T. Drive Failure Message

I purchased a DV9925nr laptop from Bestbuy about 13 months ago. Six months ago it started having the sporadic and randomly abrubt shutdown problem that so many others seem to be having.
Two days ago it developed a new problem:
I left my laptop on for a few minutes and when I returned, it was to a black screen with this message: "SMART Drive failure predicted on Hard Disk 4. WDC WD2500BEVS - 60UST0-(S1); warning: Immediately backup your data and replace your hard disk drive. A failure may be imminent. Press F1 to continue."
My question:
We have a network with two laptops and a desktop computer. There is plenty of hard drive space on the desktop system. My father has the same exact laptop model as mine. Can I put my hard disk drive into his second disk drive bay so that I can backup my files over the network to my desktop system? How would the laptop know which hard drive to boot from since they both have the same operating system on them (I am not familiar with SATA drives)?
I hope I didn't buy a lemon. Any help would be greatly appreciated.

Are you trying to do this while booted from the OS or from the install Disk? If your booted into the OS then the repair option shouldn't be click-able. Beyond that, there might be some 3rd party software that could force a reformat and/or erase. I did try to find you something but didn't come across anything specific to what your trying to do. You probably already know this, but the purpose of S.M.A.R.T. is it acts as an early warning indicator. This means the drive is no longer dependable and may fail without warning in the near future, resulting in losing all data. With that being said, I've used a hard drive that S.M.A.R.T. indicated was failing for 3+ years without a hick-up. I don't use it for anything imported though. When I have more time and if I come across anything that might get the job down, I will add to this posting. The worst case scenario is that there is no way to reformat and/or erase the drive due to the state it's in. At that point, the only thing left to do is recycling the drive.

Can I upgrade MacBook Pro hard disk drive next year?

Hi there! I'm new to the Apple Support Communities!
I am going to buy a new 13" MacBook Pro, 2.5GHz. I am going to buy the base model, with a 500GB 5400 RPM hard disk drive. Right now, I can't afford a 256GB solid-state drive, but I'll have enough for one by later next year. So, I will have done some stuff on my Mac by the time I can upgrade it. I know how to install the drive itself, but how do I transfer my information?
Here are the issues:
1) I don't know how I would make it so I could boot from an external USB.
2) And I don't know how to get all my personal information from one drive to the other.
For "2", I think I could back up my Mac to a hard drive with Time Machine, and then restore from a backup. But Time Machine couldn't back up the whole OS, right? And what would the procedure be anyway? Just turn it on when I'm done the upgrade?
If someone who has done this before could provide step-by-step instructions, I would really appreciate it!
Thanks,
Solid-State Me 

Yes you can replace the hard drive at any time. Purchase a replacement drive from any store you like - newegg or mcetech are good stores (among many others) - and when you purchase the new drive, also purchase a drive enclosure. Then download a program called "super duper" and follow the instructions to use that software. When your drive arrives, put the new drive in the enclosure, plug it in to your computer and run "super duper" with the option to "make the drive bootable" and let it finish. What it's doing is copying your drive onto the new drive. Once the copy is finished, you can shut down your computer, remove the drive, install the new one, and put the original drive into the enclosure. Now you have an external hard drive that is repurposed instead of throwing it away. Keep that drive intact for a few weeks without erasing or adding data to be sure you are happy with the new drive and how it performs. After that, use the drive to store files, backup the internal, transfer stuff, whatever.

Dismount multiple external hard disk drives

I have multiple external hard disk drives and was wondering what the command line is that will dismount all of these at once? Note that there is also one external DVD unit as well which I would not want to dismount.
Thanks,
Lyman

diskutil unmount "/path/to/disk";diskutil unmount "/path/to/disk";diskutil unmount "/path/to/disk"
Just replace replace "/path/to/disk" with the path to the mount point, leaving the quotes.
Good luck!

Lenovo ThinkPad X131e Replacement Hard Disk Drive Specifications

Similar Messages

Maybe you are looking for