LG 32LH40 32" 120hz LCD connecting to PC issues

Just purchased a LG 32LH40 lcd tv from Best Buy and the picture is great EXCEPT one issue:
I would like to use the TV occasionally as a monitor. Dead set on using DVI2HDMI and the tv is not picking up the signal. When I connect the pc and tv with the cable my pc finds the tv as a Generic PnP Display. My PC has an Nvidia 8800GTX which can handle all HD formats. After the connection is made, I open Nvidia Control Center and the tv is displayed as LG TV, but no matter what settings no luck. The TV simply displays the message 'No Signal'.
There are only two reasons I can think of that this isnt' working. First, the DVI2HDMI cables I have are not v1.3. This is most likely not the problem. Secondly, there is an issue with the tv supporting 120hz.
Going to buy a new v1.3 DVI2HDMI cable, which probably won't work. Please, if anyone has been successful with any Nvidia card to this tv let me know what you did to get it working!
Thanks a ton!

If your TV says "no signal" usually that means you're on the wrong input. You can change the TV's input with the TV remote. Press the input or source button. This should bring up a source menu, or toggle to the next input automatically. The PC input is usually the last one listed. Scroll down to it until it's highlighted, and press select/ok/enter (in the middle of the directional arrows). If everything is connected properly, this should work. If not, it's either not installed correctly, or one of the HDMI ports on the back of your TV isn't working. I hope this helps!
Nothing I post is an official statment of Best Buy or Geek Squad, it is only a helpful opinion!

Similar Messages

Unity Connection Voice Mail Issue

Hi,
I have a weird Unity Connection Voice Mail issue and would appriciate any help i can get. Many thanks in advance.
I have Unity connection 7.0 and CUCM 7.0 integrated in a lab enviroment and here is what happens.
When I place a call internally say from 2001 to 2002, things work as expected, 2002 rings and it goes to voicemail where I can leave voicemail and listen to it from 2002.
However, if I place call from the PSTN to the same number 2002 (or any other number in other sites etc) the call again rings in 2002 and goes to voicemail, unity cnx plays the greetings for 2002 and says record your message as usual. Everything up to point is fine, then when the time on the PSTN phone is showing around 14 seconds into the call unity starts playing, "to send this message press one", if I press one nothing happens.
I have rebuilt unity and cucm, even just configured the bare minimum in the lab and still getting the same result. I tried calling from E1 connection and T1 connection but with the same results.
I have run out of ideas...
===============================
Here is a call trace from an internal call:
CallData, 1, CallerId=2003, CalledId=2002, RedirectingId=2002, Origin=16, Reason=4, CallGuid=8B7859FD6C16417A9A07F507418DD25B, CallerName=, LastRedirectingId=2002, LastRedirectingReason=4, PortDisplayName=PhoneSystem-1-001
Application, 1, 2003, AttemptForward
State, 1, 2003, State - AttemptForward.cde!Dummy
State, 1, 2003, Event is [NULL]
Application, 1, 2003, PHTransfer
State, 1, 2003, State - PHTransfer.cde!LoadInfo
State, 1, 2003, Event is [TrueEvent]
Application, 1, 2003, PHGreeting
State, 1, 2003, State - PHGreeting.cde!PlayGreeting
Display, 1, 2003, Call answered if needed
Display, 1, 2003, Playing greeting for Subscriber: hq2
Display, 1, 2003, No DTMF received
Display, 1, 2003, Playing greeting for Subscriber: hq2
State, 1, 2003, Event is [RecordMsgEvent]
State, 1, 2003, State - PHGreeting.cde!RecordMsg
State, 1, 2003, Event is [NULL]
State, 1, 2003, State - PHGreeting.cde!RunEditMsg
Application, 1, 2003, -->MessageEditing
State, 1, 2003, State - MessageEditing.cde!CheckMsgMenuOpt
State, 1, 2003, Event is [EditMessageMenuEvent]
State, 1, 2003, State - MessageEditing.cde!PlayEditMenu
State, 1, 2003, Event is [HangupEvent]
State, 1, 2003, State - MessageEditing.cde!CheckMsgLength
State, 1, 2003, Event is [ManyEvent]
State, 1, 2003, State - MessageEditing.cde!SendMsg
State, 1, 2003, Event is [TrueEvent]
State, 1, 2003, State - MessageEditing.cde!ConfirmSend
State, 1, 2003, Event is [HangupEvent]
Application, 1, 2003, <--MessageEditing
State, 1, 2003, Event is [HangupEvent]
Display, 1, 2003, Idle
Display, 1, , Dialing (MWI) '2002'
Display, 1, , Idle
and here is a trace from an external (PSTN) call
Trying 142.100.64.13, 5000 ... Open
CallData, 1, CallerId=911, CalledId=2002, RedirectingId=2002, Origin=16, Reason=4, CallGuid=CA3DFD90846C4FE7B0D68298A7698287, CallerName=PSTN Emergency, LastRedirectingId=2002, LastRedirectingReason=4, PortDisplayName=PhoneSystem-1-001
Application, 1, 911, AttemptForward
State, 1, 911, State - AttemptForward.cde!Dummy
State, 1, 911, Event is [NULL]
Application, 1, 911, PHTransfer
State, 1, 911, State - PHTransfer.cde!LoadInfo
State, 1, 911, Event is [TrueEvent]
Application, 1, 911, PHGreeting
State, 1, 911, State - PHGreeting.cde!PlayGreeting
Display, 1, 911, Call answered if needed
Display, 1, 911, Playing greeting for Subscriber: hq2
Display, 1, 911, No DTMF received
Display, 1, 911, Playing greeting for Subscriber: hq2
State, 1, 911, Event is [RecordMsgEvent]
State, 1, 911, State - PHGreeting.cde!RecordMsg
State, 1, 911, Event is [NULL]
State, 1, 911, State - PHGreeting.cde!RunEditMsg
Application, 1, 911, -->MessageEditing
State, 1, 911, State - MessageEditing.cde!CheckMsgMenuOpt
State, 1, 911, Event is [EditMessageMenuEvent]
State, 1, 911, State - MessageEditing.cde!PlayEditMenu
State, 1, 911, Event is [HangupEvent]
State, 1, 911, State - MessageEditing.cde!CheckMsgLength
State, 1, 911, Event is [NULL]
Application, 1, 911, <--MessageEditing
State, 1, 911, Event is [NULL]
State, 1, 911, State - PHGreeting.cde!AfterMsg
State, 1, 911, Event is [NULL]
Display, 1, 911, Idle

Sounds like one way audio from PSTN to your Unity Connection, couple of things to check:
1. ensure your protocols are bound properly on the GW, i.e. SIP/H323/MGCP
2. Make sure IP routing is OK between Unity and the voice gateway
HTH,
Chris

My mac air will not connect to the internet. There is an exclamation point in the wifi icon and when i go into preferences i see that it is setting its own IP address. I have a macbook that is able to connect with no issue. HELP

My macbook air will not connect to the internet. There is an exclamation point in the wifi icon and when i go into preferences i see that it is setting its own IP address. I have a macbookpro that is able to connect with no issue. HELP

Reset the TC to factory and start again.
Use all SMB type names for wireless and base station.. Not apple type names.. this is more important since Mavericks.
I also recommend different names for the different bands.
So for example.
TC name.. TCgenx (I use whatever the generation number is for the x.. eg TCgen4 or latest one TCgen5)
WIreless name.. TC24ghz for 2.4ghz
TC5ghz for 5ghz
You can also set the channel manually.
If you still have issues.. start with no security and then if it fails to connect there is something seriously wrong with the laptop. Did you upgrade install Mavericks?? That can lead to driver issues.. I would recommend a clean install.

When starting the Add-on: Connection timed out issue

When starting the Add-on: Connection timed out issue
Hi,
We have a client in SAP 2005 PL 44.
I built the add-on for them using simple installer wizard ( I tried advanced set-up also).
When starting the add-on, I get the message 'Connection Timed Out'.
Add-on status is failed.
But the add-on is actually connected. i.e, The functionality associated with the add-on is working fine.
I had SAP 2007 before and un/reinstalled SAP 2005 in order to connect with this client.
I had built the same add-on in a similar way for the same client for lot many times in the past, but I never got this issue.
I tried the following:
1) Delete SM_OBS_DLL and un/reinstall DI API
2) un/reinstall B1DE
Always I'm getting this error.
Please let me know your inputs.
Thanks.
Geetha

Hi Geetha,
The timeout issue has been discussed quite a bit already on this forum. Please do a search or look at these threads:
Timed Out Error with ADDON
Addon Connection Timed out
Regards
Aravind

[svn] 1543: Bug: BLZ-152-lcds custom Date serialization issue - need to add java.io. Externalizable as the first type tested in AMF writeObject() functions

Revision: 1543
Author: [email protected]
Date: 2008-05-02 15:32:59 -0700 (Fri, 02 May 2008)
Log Message:
Bug: BLZ-152-lcds custom Date serialization issue - need to add java.io.Externalizable as the first type tested in AMF writeObject() functions
QA: Yes - please check that the fix is working with AMF3 and AMFX and you can turn on/off the fix with the config option.
Doc: No
Checkintests: Pass
Details: The problem in this case was that MyDate.as was serialized to MyDate.java on the server but on the way back, MyDate.java was serialized back to Date.as. As the bug suggests, added an Externalizable check in AMF writeObject functions. However, I didn't do this for AMF0Output as AMF0 does not support Externalizable. To be on the safe side, I also added legacy-externalizable option which is false by default but when it's true, it restores the current behavior.
Ticket Links:
http://bugs.adobe.com/jira/browse/BLZ-152
Modified Paths:
blazeds/branches/3.0.x/modules/core/src/java/flex/messaging/endpoints/AbstractEndpoint.ja va
blazeds/branches/3.0.x/modules/core/src/java/flex/messaging/io/SerializationContext.java
blazeds/branches/3.0.x/modules/core/src/java/flex/messaging/io/amf/Amf3Output.java
blazeds/branches/3.0.x/modules/core/src/java/flex/messaging/io/amfx/AmfxOutput.java
blazeds/branches/3.0.x/resources/config/services-config.xml

5.1.0 sp11 Connection pool refresh issue, revisited....again...!!!

"Hello,
From reading of these newsgroups I've seen many different manifestations
of what seems to be the same root cause with connection pools and
connections which are refreshed/replaced when found broken. In our
case weblogic server hangs.
Kit: 2xWeblogic 5.1.0 sp11 (not clusterd), Solaris 8,
java 1.3.1_01, 1xoracle 8.1.6, latest JDBC 2.0 drivers from oracle. Each weblogic instance and oracle have their own machines.
We do indeed have a firewall employed to run our subnets, and hence
our weblogic servers and oracle databses are in different DMZ's, but are
allowed to communicate to each other via rules set up on the firewall and
inspection of the logs show no such connections being dropped.
As far as the db is concerned, lookups (no writes) never take more than a few
hundred milliseconds and are then closed and given back to the connection pool
immediately from within the 'finally' block of code, hence hard to see when,if ever, the db is
is closing them due to excessive idle time.
weblogic.jdbc.connectionPool.RecipeDBPool=\
url=jdbc:oracle:thin:@foo:1521:BAA,\
driver=oracle.jdbc.driver.OracleDriver,\
loginDelaySecs=1,\
initialCapacity=30,\
maxCapacity=50,\
capacityIncrement=1,\

Alkesh wrote:
Hi Joe,
The fix you suggested has been implemented and has been running fine
now for the past 3 days. I'm delighted with the result,Great. Glad to help.
but am concerned as to why this problem wasnt highlighted during our
load-testing phases...It's a possibility that your load-testing didn't present the same sort
of load that your actual runtime does.
Thanks for your time on this.Well sure. We want you successful.
Joe
Alkesh
At 01:52 PM 2/22/2002 +0000, you wrote:
Hi Joe,
Thanks for your reply
Please find attached a copy of the jvm thread dump we got from thelast time
that weblogic blocked upon trying to refresh a broken connection.
We have turned off JIT with the environment settingJAVA_COMPILER=NONE.
FYI hotspot is enabled with '-hotspot', these settings can be foundin the
attached 'startWeblogic.sh'.Hi. I found a serious problem by reading the thread dump:
"ExecuteThread-11" daemon prio=5 tid=0x179d40 nid=0x19 waiting for
monitor entry
[0xeee80000..0xeee819e0]
at java.sql.DriverManager.getConnection(DriverManager.java:144)
- waiting to lock <f8e77ad0> (a java.lang.Class)
at com.akqa.sainsburys.jv_recipe.ejb.session.RecipeBean.getConnection(Re
cipeBean.java:759)
It is important to never call DriverManager methods in a multithreaded
application
such as Weblogic, because these JVM methods are alloverly synchronized
at
the class level. One such method, DriverManager.println(), is called
continuously
by all JDBC drivers as well as the SQLException constructor. If one
server thread
makes a long-lasting or hanging call to DriverManager.getConnection(),
it can halt
all JDBC in the whole JVM including work on other open driver
connections.
Please show me the code for RecipeBean.java, and I will send you an
altered version
that should solve this problem. In fact, I can infer from the thread
dump what is needed.
Change the one method getConnection() to this:
// Make once and re-use a driver instance directly, avoiding
DriverManager
Driver d = (Driver)class.forName("weblogic.jdbc.jts.Driver").newInstance();
public Connection getConnection()
return d.connect("jdbc:weblogic:jts:yourPoolNameHere", null );
Also, change your pool definition. I assume you have
testConnsOnReserve set to true.
(You should). Also, you should change your refresh minutes to
something huge, like
9999999. The refresh is interfering with your online performance and
is unnecessary
if you have testConnsOnReserve set. I recommend:
weblogic.jdbc.connectionPool.RecipeDBPool=\
url=jdbc:oracle:thin:@foo:1521:BAA,\
driver=oracle.jdbc.driver.OracleDriver,\
loginDelaySecs=1,\
initialCapacity=50,\ <------ note that this should be the
same as max, so all cons are made at startup
maxCapacity=50,\
testTable=dual,\
testConnsOnReserve=true,\
refreshTestMinutes=9999999,\
etc.
Joe
I've also attached some firewall logs around the time of weblogicblocking
(12.09). I could only get screen dumps for you, this may or maynot be
useful.
For the firewall logs use the following legend :-
195.110.64.205 - DNS
172.16.160.195 - host webserver 1 (i.e. what our licenses are boundto)
172.16.160.196 - host webserver 2
172.16.160.220 - website 1
172.16.160.230 - website 2
Thanks
Alkesh
-----Original Message-----
From: Joe [mailto:[email protected]]
Sent: 20 February 2002 22:09
To: [email protected]
Subject: Re: 5.1.0 sp11 Connection pool refresh issue,
revisited....again...!!!
At 02:47 PM 2/20/2002 +0000, you wrote:
Hi Joe,
Please find attached a copy of our thread dumps for the most recentoccasion
that weblogic server has stopped.
Apologies for any misunderstandings with my previous post, it appears to
have been cropped. Full posting below (yes we do have testConnOnReserve and
testTable properties set).
Thanks for your time.sure, but first let's get you running OK. These dumps seem to be
very cryptic, as if you're running a highly optimized JVM that
loses almost all of the Java class references I'd normally see.
Can you run again with a more basic JVM? I am beginning to suspect
the JIT JVM...
Joe
Alkesh
Joseph Weinstein wrote:
Hello,
From reading of these newsgroups I've seen many
different manifestations of what seems to be the sameroot cause with connection pools and connections
which are refreshed/replaced when found broken. In our
case weblogic server hangs.
Kit: Weblogic 5.1.0 sp11 (not clusterd),
Solaris 8, java 1.3.1_01, oracle 8.1.6,
latest JDBC 2.0 drivers from oracle.
We do indeed have a firewall employed to run our subnets,
and hence our weblogic servers and oracle databses are
in different DMZ's, but are allowed to communicate to each
other via rules set up on the firewall and inspection of
the logs show no such connections being dropped.
As far as the db is concerned, lookups (no writes) never
take more than a few hundred milliseconds and are then
closed and given back to the connection pool immediately
from within the 'finally' block of code, hence hard to
see when,if ever, the db is is closing them due to excessive idle time.
weblogic.jdbc.connectionPool.RecipeDBPool=\
url=jdbc:oracle:thin:@foo:1521:BAA,\
driver=oracle.jdbc.driver.OracleDriver,\
loginDelaySecs=1,\
initialCapacity=30,\
maxCapacity=50,\
capacityIncrement=1,\
allowShrinking=false,\
testTable=dual,\
testConnsOnReserve=true,\
shrinkPeriodMins=1,\
refreshTestMinutes=10,\ // has been 1 and 5 but 10 'more' stable.
Fequently however, connections are found to be broken
(either by periodical refresh - refreshTestMinutes or
testing connection before granting it to the
application - testConnsOnReserve=true), this has been
confirmed by viewing JDBC.log .
When this is so, weblogic attempts to replace these
broken connections with new ones and then proceeds
to grant it to the application. Once in a while however
(and by no means 'x' refreshes later), weblogic will not
come back.
One of 2 errors occur in our deployment which cuase weblogic
to refresh a connection.
<JDBC Pool RecipeDBPool> java.sql.SQLException: No more data to read fromsocket
and
<JDBC Pool RecipeDBPool> java.sql.SQLException: Io exception: Broken pipe
I believe these settings to all be correct, JDBC drivers
in the correct point BEFORE weblogic.aux in classpath, yet
still have the issue of broken connections.
Any ideas ? I've been reading a lot into this probelm
on various postings now, and i'm completely stumped.
Thanks for your time.
Alkesh

Connection and Keyboard Issues (since 10.5.5 update?)

Not quite the connection issues others are having, once Airport is connected, it stays connected. The issue is with initial connection. When I wake the Macbook up from sleep, I can't click to load anything on the internet/ in email for almost a full minute. If I do, or if mail tries checking for new email, whatever is attempting to load continues to attempt doing so for about 30 seconds or so, when it then tells me that I am not connected to the internet. Airport, however connects to the wifi just as quickly as ever (or, at least, it says it's connected). I just started noticing this issue the other day, around the time I updated to 10.5.5, so I can only assume it's from the update. I have not had any connection issues before this (the Macbook is about 3 months old).
The other issue I've noticed does not happen consistently. Once in a while, when I press the button to decrease screen brightness, the brightness decreases completely and the screen turns black. The other day, I opened the computer up, and the screen was "stuck" black. I couldn't get the brightness to increase. While trying to tap keys to "wake it up," at one point I heard a ding, as if there was an alert that I needed to click OK on or something. I ended up giving up and holding the power button down to shut down and reboot, and haven't had the problem again since.
I've searched the forums to see if others are having these problems, but all I can find is problems with frequent connection drops, and, like I said, I'm not have that issue.

Help?
This is very frustrating.

MBP 9,2 no longer recognizing my 3rd Gen Apple TV - wife's MPB 8,1 recognizes and connects with no issues.

My MBP 9,2 (2.9GHz i7/8GB/750HDD) no longer recognizes my 3rd Gen Apple TV while my wife's MBP 8,1 (2.3GHz/4GB/320HDD) recognizes and connects with no issues. All are running current software.

Hello herbnmyth,
Thank you for using Apple Support Communities.
I see that you are having difficulties with connecting the Apple TV with your computer. The following article provides information for troubleshooting Home Sharing and should help you sort the connections.
Troubleshooting Home Sharing - Apple Support
Regards,
Jeff D.

PowerMac 8600/250 LCD connection problem

I've an 8600/250 with a Sonnet Crescendo G4 processor upgrade; Sonnet Tempo ATA133 card; USB (v.1.1.2) card w/2 HDs--running both the native 4 gb scsi and a Seagate ATA/128 gb drives. It's all connected to a ViewSonic VX-710 15 inch LCD monitor. It is not internet connected. Of concern, a recent problem has arisen with the monitor connection. I've developed a thin white line that vertically extends down the face of the monitor adjacent the mouse scrolling marker. The line "moves" with the mouse scroll (a constant 1/2 inch relationship). Changing the monitor DPI setting to (1024X768--74.9mghz) will shorten the vertical length of the line to half the distance down the page. I'm using the analog connection with the monitor. Everything worked fine until very recently--the evolution of the line erratically developing over a few short days. The monitor, functions perfectly when hooked up as a second to my I-Mac, so I've ruled the monitor out as being faulty. Any ideas out there? VRAM memory issues? Would an ATA Rage 1280 video card installation help? I've grown rather fond of this useful, adaptive, tough little machine and it's reliability over the years. I use the computer as a dedicated platform for storage and management of years of my old OS 9.1 files and OS specific programs. I'm open to any and all suggestions.
Thanks,TMc

The long and winding road...
Voila!...it's working again. First of all, I want to thank everyone for their time and input--I tried it all. The final equation to the problem; stock VRAM.
Frustrated to no end, I wandered through the door of "Mc2", a local Mac shop (20+ years) in the nearby northern Monterey coastal burg of Soquel, CA. The shop always keeps a few older Mac's of various releases in the back for bits & pieces salvaging along with a couple of grey-hair techies who've been through it all.
The first thing asked was whether the "line" I was experiencing on the desktop had been accompanied by gradual pixel degradation over a a number of startups--it had! He responded by stating on the 85/86/9600 series motherboards VRAM serve as a through-put point, regardless of the Video card installed. He suggested "A faulty chip, especially with newer LCD monitors, will often manifest itself with a vertical line down the monitor." Additionally, he suggested this problem can also be confused as an indicator of a faulty LCD screen, BUT if the line moves with the mouse scroll or can be changed by pixel resolution/screen refresh rates, it suggests faulty VRAM--memory that should to be left in these machines for video stability. He suggested they should not be mixed and matched and need to be replaced in matching pairs.
A quick online over-night order to my trusty memory source "4AllMemory" (an excellent and reliable source for on-the-cheap new goodies for PCI macs), and Voila! With a little testing as to which chip(s) required replacement, I restarted and everything returned to normal. Relief, finally!

Help with DYNEX Model: DX-55L150A11 - 55" 120Hz LCD Television

Is there a Software Update available for this television?? I have trouble when I switch channels on the Cable box (TWC set top box). The sound disappears and the only way I can get it back is to cycle through the HDMI ports on the Dynex remote or turn off/on the Dynex remote. Seems like the Dynex TV loses sync for the AUDIO and it only "RESYNCS" when the HDMI ports are cycled. I cycle through the HDMI ports, because that is the method of connection between the Cable Set-top box and the TV.
Also, the 120 Hz operation is blurry during a football game. I need to shut off the 120 Hz processing and watch the raw video and it is not blurry. WHY???
Overall, the TV is operating okay, just wondering if a Software Update would help this TV????

There is currently no software update available for your TV. However, your sound problem is caused by a communication issue between your cable box & TV via the HDMI cable. An easy test is to plug in another source (like a DVD or game consol) to the same HDMI input, with the same cable, problem goes away, it's the cable box / provider issue. The TV does not know what is plugged in, it's just processing the information it receives. TWC boxes (likely Scientific American or Motorola built) have many problems with HDMI communication. The quickest, easiest, cheapest solution as suggested by cmartin is to switch to component cables. Your TV can process full resolution HD through the component inputs eliminating the troublesome HDMI communication line. Cmartin's other issue sounds like an overloaded cable system and his provider should be running additional lines if useage is overwhelming the bandwidth. HDMI has been troublesome since it's creation and with more products coming out of different countries with no communication standard, everything is 'talking a different language' and compounding the problem.
Regarding your 120hz question, using this function without a true 120hz (frames per second) input signal (currently only used by 3D primarily, and a few select BluRay and video games), the TV's processor takes available incoming frames and averages them together to create additional 'false frames' which are added in between (frame 1-2-3 becomes 1-1.5-2-2.5-3-3.5, etc.) often causing a choppy or blurring effect with normal video conditions. It's purpose and only real current benefit is under very fast moving video conditions when the gap between frames may be more evident.
-Agent M
www.facebook.com/geeksquadrecon
www.twitter.com/geeksquadrecon

Wireless LCD connection?

Does anyone know of a way to connect a mac (or PC) to an existing LCD projector wirelessly? Is there some sort of dongle that can be plugged into an LCD projector that can wirelessly pick up signals from a mac or PC? I have to set up a room for a lecturer and they want two LCDs displaying the powerpoints (or Keynotes) and I would rather not run a long extension cable between them. If I can avoid this, it would be better. Any ideas?

Hi cambridgeuser,
Welcome to Apple Discussions!
In order to get the video from your MacBook Air to your TV, you'll need to run some sort of cable between the two devices. What version of the MacBook Air do you have? The first generation (that came with adapters) or the second generation (that has adapters which are sold separately)?
Next, we'll want to confirm what input ports are on your TV. Does it DVI? HDMI? Component? This will be indicative of what sort of cable/adapter you get.
Let us all know about that information so the appropriate information can be given.

External LCD connected via mini DP- Dsub keeps switching off in XP

I have a Benq E2200HDA screen connected to Macbook via the adapter. Under OSX everything is fine, but when working with XP the screen turns off for a few seconds every 10 minutes or so. The display doesn't turn off, it looks more like the computer is feeding it a blank input. I installed the newest nvidia drivers but it didn't do anything.
Has anybody encountered this problem and know how to solve that?

Nobody had this problem?

Lcd crack causing motherboard issue?

In recent post I stated I cracked my lcd, then my connectors would not connect. Verified my lcd part number and had the ribbon cable replaced...
New Lcd did not work. ..
Now, I'm being told the motherboard may be the issue.
Question 1) Return screen pay shipping and 10% restock and get another screen in case it was defective?
Q 2) Buy something other than Pavillion which I'm told motherboard overheats?
What would you do? I'm a Cyber Security/Forensics student and need this issue fixed asap, just hitting dead-ends and the bottom of my bank acct.

Is the DC socket separate from the motherboard?
If it is, it may be defective.

W510 Hardware LCD Screen Red-Colored Issue

It seems that after a rough transport of my W510, the screen is now malfunctioning with a grainy/noisy static-filled image that's tinted red all over. I am hoping this is a cable issue, similar to when you jostle loose your computer VGA/DVI cable and discoloration occurs.
Here's what it looks like:
Image 1
Image 2
What steps should I take now? My warranty is expired.

Seems like a good guess, and some reports online also indicate that it could be a solder joint loose on the motherboard. But I need some test to diagnose this as the LCD display or the Mobo. What do you think? Okay, and I already reconnected the connections from the cables to the motherboard, but what about the cables leading to the LCD itself? I didn't take it apart that far. Are there more connections within that top half of the laptop that could possibly be causing this?

My new IPad 3 cannot connect to WIFI even it has a full bar of the reception. In the same location, my PC and my smart phone get a full bar connection without any issues. How can I do to fix the issues (can I switch to IPad 2)?

My new Ipad 3 cannot connect to WIFI even it has a full bar of reception. In the same location, my Windows 7 PC and Andorid Smart phone can connect to the same WIFI without any issues. How can I fix it? Without WIFI, the WIFI only IPAD is nearly useless. If it cannot be fixed, can I get a replacement for IPad 2?

Take it to an Apple Store for evaluation. If defective, you'll get a replacement.
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
 Cheers, Tom

LG 32LH40 32" 120hz LCD connecting to PC issues

Similar Messages

Maybe you are looking for