Limited access after securing

I have just recently secured my wrt54gs router with a WEP security. My laptop however, when I try to connect, will connect to the network with limited access only. It will not let me onto the internet. I have tried new firmware. Powering off the router and resetting it, but none of it has worked. The 2 house laptops do the same thing. One is on vista the other on xp. The network will connect fine and will allow me to use internet as long as there is no security. Help Please!

You should really try to NOT use WEP security as it is easy for hackers to break. Use the WPA / WPA2-Personal as they are more secure.
You MUST be sure the passphrase / hexkey on EACH computer exactly matches the passphrase / hexkey on the router or they wont talk to each other. But I think you know that already as you have communication from PC to router.
Look under the 'Wireless' tab. You may have a setting on the router for Wireless security for "Wireless MAC Filter". This setting restricts what wireless devices can access your network (and thus the internet). I believe that if you don't specifically either disable the wireless MAC filtering (allowing EVERYONE on your network), or enable it and allow only YOUR machines (by MAC address) on the router, they won't get internet. I *think* you might be able to 'see' the rest of your network (because of the hexkeys), but not the internet.
But you need to use WPA or WPA2 encryption if at all possible. Then you would have to come up the 26 character HEX key (numbers 0-9 and letters a-f). Actually, I think it is 13 hex 'digits', each hex 'digit' consisting of 2 characters (0-9, a-f as above). You MAC address is an example of a hex string.
Hope this helps ya.
LB

Similar Messages

My wifi connection shows limited access after updating my window 8.1

Hy wishes for all of you. Having trouble after update my window 8 to 8.1. Perhaps the wrost day of my life. After update lost my Internet connection. It's shows limited connection and unindentify network. I search different post on Web regarding this problem and applied but all in vain. I would like to restore my old window but I don't have backup so now have true in trouble kindly help me out
Would be thankful to all of you
Regards

Hi:
If you live in the USA, you can order recovery media by clicking on the link below, select the W8 operating system, click on Order Recovery Media.
http://h22207.www2.hp.com/us-en/drivers/selfservice/hp-envy-m6-1100-notebook-pc-series/5296045/model...
Did you try this W8.1 wireless card driver?
http://h20566.www2.hp.com/hpsc/swd/public/detail?swItemId=ob_142231_1#tab1

"Safari attempted to access a secure website..." after 10.8.2

I upgraded to 10.8.2 this afternoon and now my son's parental controled account is broken. Whenever he tries to access a web page via Safari (or Chrome) he gets a message stating "Safari attempted to access a secure website..." I haven't changed anything on his account - it worked fine before the upgrade, so I assume 10.8.2 caused the problem.
I do have Parental Controls on his account, but web browsing is set to Unlimitied Access.
Please Help!

Still experimenting, but I think I may have solved the problem. Try this:
Log out of the account with Parental Controls enabled.
Log into an account with administrative priveleges
Go to System Preferences | Parental Controls
Click the padlock and authenticate with the administrator's credentials
Click on the account with the Parental Controls enabled
Turn off Parental Controls for that account
Log out of the administrative account
Log in to the account that had Parental Controls enabled
Try browsing to see if any error messages appear (none should)
Log out of the account
Log back into the account with administrative priveleges
Follow the same process as earlier to find the account that should have Parental Controls enabled and enable restrictions accordingly; ensure under the Web tab that "Allow unrestricted access to websites" is enabled (if that's the setting you wish the account to have... which in my case, it is)
Log out of the administrative account
Log in to the account that has Parental Controls enabled
Try browsing to see if any error messages appear (none should)
This has worked for me on one of the six workstations I'm administering. I'll have the opportunity to test the remaining 5 in a few minutes.

Lenovo G400s Wireless Connection Limited Access on Windows 7 Ultimate - 32 bit

Just bought Lenovo G400s, install windows 7 ultimate - 32 bit on it.
It turns out the wireless network driver need to install manually, the disc driver that came with laptop was for windows 8.1. So I went to lenovo website, put on the series and download the wirelss network driver which is around 250 MB.
I installed the driver and connect to the wireless network. My office wireless was on security and use static ip. I changed the ipv4 ip static already. It connected for a while, 1-2 second then lost connection. I checked with ping to google, got 2 records of live connection which is very short. After that it try to reconnecting itself again and again with status said "Limited Access"
I search in google, read some forums about problem in different series, so I use another computer go to Intel website to download latest driver. Got it installed, but it's still the same.
I try download broadcom driver, but it's really different and doesn't work at all.
Now I don't know what to do.
Windows 7 Ultimate - 32 bit
Inter(R) Centrino(R) Wireless-N 135
Driver Provider: Intel
Driver Date: 1/26/2014
Driver Version: 15.11.0.7
Digital Signer: Microsoft Windows Hardware Compability Publisher
What makes it weird, although from intel website said the driver date is in 3/21/2014, and the version is 16.11.0, but this information I get from device driver was different.
Here's the intel's website if you're wondering:
_https://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Wireless+Networking&ProductLine=Intel%C2%AE+Wi-Fi+Products&ProductProduct=Intel%C2%AE+Centrino%C2%AE+Wireless-N+135#&OSVersion=Windows%207%20(32-bit)*&DownloadType=Software%20Applications
Can anyone help me?
Solved!
Go to Solution.

Today I want to install windows 8.1 on it, because the laptop came with windows 8.1 driver disc.
However, I try the wireless connection once again , one final try before I clean install the OS.
It turns out the internet connection is connected. Ping is quite stable, got a small drop. Nonetheless, IT'S CONNECTED!!!
I don't know what happened, I tried thousand ways yesterday and gave up. Today I don't set anything just try connecting with static IP set the ipv4 just like I did yesterday, and it connects without hassle!! is there a pc fairy or what?
The possible way I can think of is the router's internet connection's got restarted since It's a new day at office.
Despite how it solved still mystery to me, I think I mark this thread as Solved.

No internet Access, Unidentified Network or Limited Access in Windows 7 in home wifi network

Unable to access the internet from my home wifi network. its giving error Unidentified Network, limited access. but able to access in office wifi and hotel wifi network. through wired connection from my home router, able to access the internet. able
to access inter net from another laptop the same wifi configaretion.
After reformated also same issue.
I am using windows7,64-bit OS, Laptop model Dell Latitude E6430, my home internet provider are Beam telcom
Anti Virus : McAfee
Please help us on this...

Log Name:      System
Source:        Microsoft-Windows-Time-Service
Date:          7/5/2014 8:43:52 PM
Event ID:      129
Task Category: None
Level:         Warning
Keywords:
User:          LOCAL SERVICE
Computer:      IND-6GWY5Z1.geips-euro.ps.ge.com
Description:
NtpClient was unable to set a domain peer to use as a time source because of discovery error. NtpClient will try again in 3473457 minutes and double the reattempt interval thereafter. The error was: The entry is not found. (0x800706E1)
Event Xml:
<System>
    <Provider Name="Microsoft-Windows-Time-Service" Guid="{06EDCFEB-0FD0-4E53-ACCA-A6F8BBF81BCB}" />
    <EventID>129</EventID>
    <Version>0</Version>
    <Level>3</Level>
    <Task>0</Task>
    <Opcode>0</Opcode>
    <Keywords>0x8000000000000000</Keywords>
    <TimeCreated SystemTime="2014-07-05T15:13:52.341986500Z" />
    <EventRecordID>13018</EventRecordID>
    <Correlation />
    <Execution ProcessID="524" ThreadID="6732" />
    <Channel>System</Channel>
    <Computer>IND-6GWY5Z1.geips-euro.ps.ge.com</Computer>
    <Security UserID="S-1-5-19" />
</System>
<EventData Name="TMP_EVENT_DOMAIN_PEER_DISCOVERY_ERROR">
    <Data Name="ErrorMessage">The entry is not found. (0x800706E1)</Data>
    <Data Name="RetryMinutes">3473457</Data>
</EventData>
</Event>

WRT120N 'Limited Access' & Other Problems

Searched the forum but couldn't find anything specific to the limited access problem.
I have a WRT120N with Firmware 1.0.06
First peculiarity is that I can't access the web based admin screen from Firefox 7.0.1. The password prompt appears but won't proceed from there.
Second, and main issue is that frequently (several times a day) I get a 'Limited Access' error on my wireless connection. On mouse roll over Windows 7 Pro gives the error message 'no internet access'. This problem appears to resolve itself after several minutes or straight away if the router is powercycled. During these 'Limited Access' moments I am unable to connect to the route web based admin page nor ping or tracert.
Settings:
WRT120N
Firmware Version:
v1.0.06 build 001 Apr 29 2011 11:08:40
Boot Code Version:
v0.03
Connection Type:
Automatic Configuration - DHCP
Mode:
Wireless-N Only
Network Name (SSID):
(removed)
Channel Width:
Auto (20MHz or 40MHz)
Wide Channel::
Auto
Standard Channel:
Auto
Security:
WPA2 Personal
SSID Broadcast:
Enabled

For the first issue:
*Did you type 192.168.1.1 on the address bar? Also, the default password is "admin" and you have to leave the Username field blank.
Have you tried doing the following?
* Connecting the computer directly to the modem. The limited or no connectivity issue may be due to a problem with the Internet connection. If you still cannot connect to the Internet, you may need to call your ISP.
* Connecting the computer directly to the router with an Ethernet cable. If that didn't work, you might want to check the firewall settings. Try setting it to Low or try disabling it for the moment.
* If you're able to connect to the router with an Ethernet cable, you can also try checking the wireless settings. Try setting the network mode to "Mixed" and select the 20MHz Channel width and 6, 9, 11 channels.
* using another wireless device to connect to the network wirelessly. There's also a possibility that the problem may be resolved by updating the firmware of your wireless computer's adapter drivers.
* The location of your router is could also affect the wireless connectivity. As vai_fan mentioned, you need to avoid placing the router near any other devices which emit wireless signals like cordless phones, microwave ovens, etc.
"Don't fix it if it ain't broken."

Applications not responding apparently after Security Update 2007-009

Mail, iTunes, Skype, MSN Messenger, MainMenu, Emule, Safari and god know what else aren't responding after Security Update 2007-009.
Hi,
I recently purchased a new phone that does not work with macs, so I bought an application from Feisar to make it work. The application isn't freeware, so I think it is very unlikely that it bogused my system. Anyway, I installed the software, but only afterwards noticed it didn't work for my phone model with the USb interface, only through bluetooth, which I don't have. Moreover, and, in my opinion, more importantly, I also downloaded and installed security update 2007-009. After the update, I mandatorily restarted OS X and instantly noticed Mail, iTunes, Safari, Skype and Messenger not working. I click on them on the dock, they bounce (usually once, but it has occured to be more) and nothing happens. I don't get the little arrow below the icon. I see the applications in the applications folder, so they are not missing. I searched and searched on the internet and, apparently it is, to say the least, herculeanly complicated to downgrade from a software update. I tried to repair permissions and it didn't work. I tried the apple hardware test and everything came out perfect. I restarted many times and the same keeps happening.
So I wasted half my day yesterday trying to fix this, looking into forums and trying to talk to people about it and there it absolutely no answer. Yesterday I installed the programs necessary to sync my phone in my wife's macbook and nothing bad happened. So I'm guessing it isn't about the phone plugins I installed. I've tried to download combo updates but they crash as soon as I try to install them - I even tried to install a 10.4.10 update.
This is the error message I get:
Command: Installer
Path: /Applications/Utilities/Installer.app/Contents/MacOS/Installer
Parent: WindowServer [114]
Version: 2.1.9 (104)
Build Version: 36
Project Name: Installer
Source Version: 1040000
PID: 603
Thread: Unknown
Link (dyld) error:
Symbol not found: _WebCoreUnicodeDirectionFunction
Referenced from: /System/Library/Frameworks/WebKit.framework/WebKit
Expected in: /System/Library/Frameworks/WebKit.framework/Versions/A/Frameworks/WebCore.frame work/Versions/A/WebCore
/System/Library/Frameworks/WebKit.framework/WebKit
I put part of in on google to check if there was anybody discussing anything related and someone suggested - bizarrely enough - updating adobe reader. I did it just in case and, of course, it didn't work. I repaired permissions a million times already, I rebooted in safe mode, I scaned the computer with apple jack (which reapetedly said that I had a "fan failure!"), I verified the disk with diskutility - which showed nothing. I tried downloading an anti-virus (ClamXav), but I couldn't open it also, I trashed my prefs, I deleted all internet plugins, but still.... nothing.
The most likely line to follow here is the "fan failure" message in apple jack. I looked inside my g5 and all fans except for the one close to the Hard Drives aren't spining. I'm not sure this means they aren't functional or whether the temperature isn't high enough for it to be turned on. Temperature must be around 26-28 degrees Celsius today. There is nothing on the internet about that fan failure that's close enough to my case.
I'm about to quit and take it to the very expensive - yet reliable - authorized tech support apple has in Rio. Any ideas, anyone?

Maybe it is a security update thing! I have had similar troubles with my CS2 and other simple apps like TextEdit not opening, just doing that single bounce... I have tried EVERYTHING and now, after reinstalling my entire system, have lost access to my own user profile.
I'm assuming you have tried starting up with your original system install disk in the computer, while you turn it on, hold the option key, it will allow you to run another hardware check, as well as to do an archive install if it comes down to that.
good luck, please let me know if you find out something else that might be causing the problems... i've noticed that alot of mac threads have similar probs listed.

How to set up full access and limited access wireless networks to laptops

Dear Apple,
I just received my Apple 1 TB Time Capsule. Can someone please help me with a network configuration I want to set up?
I have a cable modem, and, three computers: a G4 iMAC (system 10.5.5), an Apple MacBook (system 10.5.5), and, a PC laptop.
The Time Capsule is connect directly to the cable modem.
Regarding the computers:
(1) I want the G4 iMAC to connect directly, via an Ethernet cable, to the Time Capsule, WITH FULL ALLOWED ACCESS to the Time Capsule and to the back-up function of the Time Machine feature, and, with allowed access to my HP inkjet printer (class 6110);
(2) I also want the MacBook laptop to wirelessly link to the Time Capsule via the Airport utility on the laptop, and, WITH FULL ALLOWED ACCESS to the Time Capsule and to the back-up function of the Time Machine feature (using WPA/WPA2 security, and, without the network name visible to third parties), and, WITH allowed access to my HP inkjet printer (class 6110);
(3) I want the PC laptop to wirelessly link to the Time Capsule (using WEP security), but WITHOUT ACCESS to the Time Machine, WITHOUT access to the back-ups on the iMAC, WITHOUT access to the back-ups on the MacBook, and, WITHOUT access to the inkjet printer --- I only want the PC to use the Time Capsule as a WIRELESS ROUTER so that the PC laptop can access the internet.
(4) And, finally, I want to specify (Time-Capsule/Time-Machine/server ) access ONLY to the iMAC and the MacBook, so that others cannot gain any access.
I specifically need help to set up and configure the Time Capsule so that the PC laptop, as stated above, should have limited access to the Time Capsule --- namely, only to access the internet, and, not even be aware of stored data on the Time Capsule, not even be aware of the inkjet printer, and, not even see my WPA network name when the PC scans for wireless devices.
I also want the iMAC and the MacBook to have access to each other’s data stored on the Time Capsule (like a common server).
I have an old D-Link DI-624 wireless router that I used before buying the Time Capsule, which is available, if needed. Hopefully, I can configure the Time Capsule so that I would not need the old D-Link.
Thank you in advance,
David.

The basic method for remote access is not changed.
http://gigaom.com/apple/access-your-time-capsule-over-the-internet/
You have a few issues.
The really big one.. the school firewall should not let you connect to home.
Check the IT admin at your school but if they allow anything but a few protocols like http and https through, they are not doing their job. You cannot afford in a large network to have every Tom Dick and Harry access any open device.. that can introduce viruses and trojans into the network behind the firewall.
The general method for remote access on large networks is vpn and the TC offers no vpn connection.. just AFP.
If you intend using 3G wireless stick or the like then you can get access.
The next issue is static public IP or how to find the TC.. you need some way to find the IP if your ISP does not offer static ip, and the tc has no dyndns client. Since Apple shut down new users for mobileme and will close that service there is no method to find the TC IP without owning your own domain. You would be better placing the TC in bridge behind a router that does offer dyndns and port forward AFP (TCP 548) to it.

Apple mobile device support install/uninstall sets my wireless to limited access

Dell Pavilion dv7
Windows 7 64 bit.
Current itunes 10.4
When installing itunes 10.5, my wireless connection changed to limited access. I can not connect to the internet with wireless. If I put my ethernet cable in, i can connect to the internet through the ethernet cable.
I found no solutions to fix the limited access issue. So, i had to restore my system. After the restore my wireless connection could connect to the internet again.
But now itunes does not work. One of two messages come up. The latest (i have done several system restores). Either quicktime was not found or something about iTunes Library.itl is out of synch with the current version of itunes.
Now i decide to uninstall all the itunes installed products one at a time. Itunes, quicktime, Apple software update, Apple mobile device support and there it goes, my wireless connection changes to limited access again.
Any help would be great.

Let's try a standalone Apple Mobile Device Support install. It still might not install, but fingers crossed any error messages will give us a better idea of the underlying cause of why it's not installing under normal conditions.
Download and save a copy of the iTunesSetup.exe (or iTunes64setup.exe) installer file to your hard drive:
http://www.apple.com/itunes/download/
Download and install the free trial version of WinRAR:
http://www.rarlab.com/
Right-click the iTunesSetup.exe (or iTunes64setup.exe), and select "Extract to iTunesSetup" (or "Extract to iTunes64Setup"). WinRAR will expand the contents of the file into a folder called "iTunesSetup" (or "iTunes64Setup").
Go into the folder and doubleclick the AppleMobileDeviceSupport.msi (or AppleMobileDeviceSupport64.msi) to do a standalone AMDS install.
(If it offers you the choice to remove or repair, choose "Remove", and if the uninstall goes through successfully, see if you can reinstall by doubleclicking the AppleMobileDeviceSupport.msi again.)
Does it install (or uninstall and then reinstall) properly for you? If so, can you get a normal iTunes install to go through properly now?
If instead you get an error message during the install (or uninstall), let us know what it says. (Precise text, please.)

Problem in Dimension File after securing Dimensions

Hi,
Why is there an error message "There is a problem in dimension file : ACCOUNT" in BPC for Excel if i do a "secure" and "R/W" on ACCOUNT dimension?
Actually this error message seems to happen to every dimension except for "Category" and "Entity", any idea why?
Cheers

Hi,
I do not believe that you can secure the Account dimensoin in BPC 5.1, you should however be able to secure all the other dimensions.
Can you please check if you have updated your Member Access Profiles after securing a new dimension. You need to add this new dimension to your Member Access Profile (for each applicaiton where the dimension is used), otherwise you will get error message in the Excel Front-End.
Regards,
Marcel

Kdcmond could not launch, after security update Nov 09,OS 10.5,Powerbook g4

Powerbook G4 will not boot past the grey screen with spinning wheel after latest security update from Apple.
In safe mode: kdcmond could not launch is reported.
I DO NOT HAVE EASY ACCESS TO INSTALLATION DISKS.
Please post suggestions that are viable using rm or vi in safe mode.
It will take the IT department weeks to get around to fixing this so I am hoping for usable responses in the short term.
Powerbook G4 1GB os 10.5.7 to 8 Grey Screen/crash with exceptions after security update.
Took corrective actions using Disk Utility then Applejack with no success. Deleted Library/Prefernces/SystemConfiguration files: NetworkInterfaces.plist, com.apple.airport.preferences.plist, and preferences.plist to get them to regenerate. The exception is gone but now, kdcmond could not launch is reported due to no localhost name found.

No suggestions from anyone so I am giving up and returning the PC to IT. I will leave the thread open in case anyone comes up with any ideas for future reference.

Can't access some secure sites through proxy?

can't access some secure sites through proxy server on osx it just keeps going local authority couldn't be contacted, i had the same problem with parental controls, but now that is off and its still doing it, is there a setting or something i need to enable?

In my original post, not today's, I had said I was having the issues on the Mini, running OSX 10.6.8 and Safari v.5.1.5 for my bank's pill pay. I should have been more specific as to which machine and OSX Safari browser I'm having the T-Mobile problem with. My mistake.
It is on both the MacMini and now the Air too. A moment ago, I was able to log in to my.t-mobile.com on the Air, but after putting into my Bookmarks folder, I can't do it anymore. The Log in button comes up greyed out instead of green.
I'm also still having trouble with my bank's bill pay section on both computers too.
I wonder if it's related to the saving of the log in info or putting in the Bookmark Folder?

Limited-access user permission lockdown mode and allowing anon users to view list items

I'm working on setting up a public-facing SharePoint website that will need to support anonymous user access. I'm using the Enterprise Publishing Portal site collection template, so the Limited-access user permission lockdown mode feature is turned on.
Everything is working great, except allowing users to view a list item. One of the key features I was hoping to leverage was the ability to display custom lists on a web page using a List View web part. Then they could click on an item and see the DispForm.aspx
so the item's content was accessible, including any file attachments.
A real-world example is adding an RSS viewer web part to the home page and allowing anon users to click on one of the events to see the details of it. Currently, in lockdown mode, the users gets an authentication prompt.
I toyed with the idea of turning the lockdown feature off. However, I'm uncertain of the full impact that would have on security. For example, I know it will allow anonymous users to see who created and modified an item, which we don't want exposed to the
public (i.e. our employee names). Seems like opening a can of worms by disabling the lockdown mode...
Any ideas on how to tackle this would be greatly appreciated.

So far, this is the most promising solution I've come across:
http://soerennielsen.wordpress.com/2012/05/29/how-to-make-list-items-visible-to-anonymous-users-in-search

With this latest update (on 4/10/15) I am unable to access a secured work website due to the TLS. How do I revert back to the previous settings?

I need to revert the security settings back to the way they were BEFORE the update because now I am unable to access my secured work website (that I was on yesterday) to actually do work. When I attempt to go to my log-in page I get the following message:
Secure Connection Failed
The connection to corect.ct.gov:10000 was interrupted while the page was loading.
The page you are trying to view cannot be shown because the authenticity of the received data could not be verified.
Please contact the website owners to inform them of this problem.
It doesn't even give me the option to allow the site (it is my computer after all, it should be my choice). I NEED TO GET TO THIS WEBSITE.

The website may try to fallback to TLS 1.0 in a way that is no longer allowed in current releases or may be using a deprecated cipher suite.
You can open the <b>about:config</b> page via the location/address bar and use its search bar to locate this pref:
*security.tls.insecure_fallback_hosts
You can double-click the line to modify the pref and add the domain (corect.ct.gov) to this pref.
If there are already websites (domains) in this list then add a comma and the new domain (no spaces).
You should only see domains separated by a comma in the value column.
*https://developer.mozilla.org/en-US/Firefox/Releases/36/Site_Compatibility#Security
*https://developer.mozilla.org/en-US/Firefox/Releases/37/Site_Compatibility#Security

WRT54G Limited Access in Vista

I have an XP and a Vista machine on my wireless network. The Vista computer keeps going into limited Access Connection after it is on for a while. The XP machine never looses connection. To connect again all I have to do is disconnect from the network then reconnect and it works fine, but I hate having to do that all the time. My cousin with Vista and a WRT54G router has this same problem also.

Update firmware, perform hard reset. Set all settings again. Change wireless channel to 1,6,9,11 and check which is best for you. Change advanced wireless settings : change beacon interval to 50, fragmentation threshold to 2306, RTS threshold to 2307, DTIM to 2

Limited access after securing

Similar Messages

Maybe you are looking for