Lion client can connect ONCE to SL server...

I've been running a small network of about 30 macs (largely iMacs) for a few years now.  Server is 10.6.8, most clients are 10.6.8 as well, with a couple 10.5.iforget.  I haven't really had many issues.  However, we just added a few more computers and (of course) they are running Lion.  Out of the box, they wouldn't even seem to see my server until I upgraded to 10.7.4.  However, now, I can log in with a network account when I first boot up.  If I log out and try to log back in with ANY network account, I get "Unable to login to account X at this time".  Restarting the computer allows me to log in.  I can't seem to see anything in the logs that would indicate a problem, but I'm also not exactly sure which logs or lines to really be focusing on.
Another issue is that after binding the Lion client, the computer does not show up in WGM.  I have the 10.7 Server Admin tools installed on the Lion clients.

Idon't see why not I'm running SLS od master and lion od master (has to be for profile manager)
The lion server is bound to the SLS (without password) and gets my users and groups from the SLS
I also have lion clients managed by SLS using PHD I'm not seeing the problems your getting
Does it make a difference if you wait a minute or so before logging in again
Do you have the same problem with none loin network accounts
Are your network homes AFP
Sounds like lion can't find your network home when you re login

Similar Messages

  • Exchange 2013 - Prevent Outlook Clients From Connecting To A CAS Server In A Different AD Site

    Hi all,
    I could really do with your help!
    We have 3 physical sites, A, B & C, with sites A & B having a really fast low latency links between them, so from an AD point of view they are 1 site.  Site C has links to both sites A & B, but the link is a lot slower.
    We have an exchange design with 3 servers (one located at each physical site) that will form a DAG spread over the 3 physical sites.  Ideally we will separate the CAS and mailbox server roles out and have them controlled by a hardware load balancer,
    however we can have both roles on the same server if required.
    What we want, is to prevent is a situation where an outlook client in site C connects to a CAS server in site A/B with the mail being hosted on a mailbox server in site C therefore traversing the network twice to get its mail.
    From doing the Microsoft training course, my understanding is that in Exchange 2013, the CAS server only proxy's the request on to the mailbox server and does not redirect the request to the CAS server in the site where the mailbox server resides.
    I have seen information online stating that a single namespace is the way to go as long as your site links/network bandwidth is good, but nothing to help with our scenario.
    Has anyone else come across this situation and how did you get round it?
    Thanks in advance :)

    Hi Johnson,
    Based on my knowledge, Outlook Client will connect to the CAS server which in local first.
    Please check whether the CAS server that in site C is healthy.
    If the CAS server in site C is healthy, please disable the CAS Load Balance for testing.
    Also found a useful blog for your reference:
    Exchange 2013 Client Access Server Role
    http://blogs.technet.com/b/exchange/archive/2013/01/25/exchange-2013-client-access-server-role.aspx
    Thanks
    Mavis
    Mavis Huang
    TechNet Community Support

  • VPN clients can connect via SSTP but not IKEv2 due to error 808

    I have a Windows Server 2012 R2 with RRAS configured to allow SSTP / IKEv2 VPN connections. I'm using an external certificate for server authentication and the client authentication is done via domain username/password (Protected EAP). The clients can
    connect successfully when using SSTP, but if IKEv2 is selected, then the following error is displayed:
    Error 808:
    The network connection between your computer and the VPN server could not be established because the remote server refused the connection. This is typically caused by a mismatch between the server's configuration and your connection settings. Please
    contact the remote server's Administrator to verify the server configuration and your connection settings.
    My external certificate has the Server Authentication EKU but not the IP security IKE intermediate, however it's the only
    certificate installed, so I believe the certificate is OK.
    Any ideas on what is causing the error?
    Thank you.
    Ricardo Costa

    Hi,
    What NAT device you are using? You must configure the IKEv2 related protocol on your NAT device too. For example if you are using the Cisco® NAT device you must
    enable the IKEv2 support on the outside interface:
    Enabling IKE on the Outside Interface
     You must enable IKE on the interface that terminates the VPN tunnel. Typically this is the outside, or public interface. To enable IKEv1 or
    IKEv2, use the crypto ikev1 | ikev2 enable command from global configuration mode:
    =================================================
    crypto ikev1 | ikev2 enable interface-name
     For example:
    hostname(config)# crypto ikev1 enable outside
    =================================================
    The related third party information:
    Configuring IPSec and ISAKMP
    http://www.cisco.com/c/en/us/td/docs/security/asa/asa84/configuration/guide/asa_84_cli_config/vpn_ike.html#wp1042302
    You can refer the following KB to enable the RRAS logging.
    RRAS: Logging should be enabled on the RRAS server
    http://technet.microsoft.com/zh-cn/library/ee922651(v=ws.10).aspx
    Hope this helps.
    *** This response contains a reference to a third party World Wide Web site. Microsoft is providing this information as a convenience to you. Microsoft does
    not control these sites and has not tested any software or information found on these sites; therefore, Microsoft cannot make any representations regarding the quality, safety, or suitability of any software or information found there. There are inherent dangers
    in the use of any software found on the Internet, and Microsoft cautions you to make sure that you completely understand the risk before retrieving any software from the Internet. ***
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • How many clients can connect through cisco AP 1310 in wireless network ?

    I had setup wireless network with
    wlc4402,cisco AP 1310.1131 and 1242 and Cisco acs 4.1.My problem is only 30 clients connect through Cisco AP 1310 at a time.I can not connect more than 30 clients at a time.What is the issue in wireless network?please reply .
    Thanks and regards
    By
    D.Anbudurai

    WIRELESS > 802.11 > RRM
    How can do that setting ? Can you reply with
    some brief steps? And also I want to know how
    many clients can connect in wireless network at
    a time exactly through cisco aps?
    Thanks and regards
    d.anbudurai

  • How many clients can connect to AP54G?

    Pls let me know how many clients can connect to AP54G?
    I find in it's spec, but can't find.
    Thanks!!!

    no answer...
    any in my question wrong?
    Please..................

  • How many users from an application can connect to a SQL server at a time?

    HI,
        I need to know , How many users from an application can connect to a SQL server at a time? Do we have any settings for this in SQL server for limiting the users?

    This is a difficult question, since it is both technical and legal.
    The absolute maximum number of connections is around 32700, but unless your server is very beefy, it will choke long before that. A connection is not a user - an application can have many connections for the same user. Depending on your license
    model, you may be legally limited to a certain number of users, but this number is not enforced technially.
    Erland Sommarskog, SQL Server MVP, [email protected]

  • Open source web calendar client to connect Mac OS X Server iCal service?

    Is there any open source web calendar client to connect Mac OS X Server iCal service?

    [Here is a crib sheet for connecting Windows to Samba|http://labs.hoffmanlabs.com/node/1590]

  • Can I determine what clients are connected to my weblogic server?

    Hi, is there anyway of determining what clients are connected to my Weblogic 8.1 server - I want this information to be generated for me, not by maintaining a list when clients login initially to the server.
    Also is there any thing that gets fired when a client terminates prematurely - for example being killed by the task manager. I need to know this, so the server knows what users are currently logged in, to prevent a user logging in twice (via the same username login).
    Cheers,
    Ants.

    Hi,
    Cousld u send me a simple example to check my Weblogic server for EJB with client.
    Iam struggling from last todays.
    and also tell what software i should use for deployment of EJB of weblogic 8.1.
    ur help highly appriciate by me
    My mail ID: [email protected]
    thanks,
    AHOY

  • Cisco ASA 5510 - Cisco Client Can Connect To VPN But Can't Ping!

    Hi,
    I have an ASA 5510 with the configuration below. I have configure the ASA as remote access vpn server with cisco vpn client, my problem now is I can connect but I can't ping.
    Config
    ciscoasa# sh run
    : Saved
    ASA Version 8.0(3)
    hostname ciscoasa
    enable password 5QB4svsHoIHxXpF/ encrypted
    names
    name xxx.xxx.xxx.xxx SAP_router_IP_on_SAP
    name xxx.xxx.xxx.xxx ISA_Server_second_external_IP
    name xxx.xxx.xxx.xxx Mail_Server
    name xxx.xxx.xxx.xxx IncomingIP
    name xxx.xxx.xxx.xxx SAP
    name xxx.xxx.xxx.xxx WebServer
    name xxx.xxx.xxx.xxx cms_eservices_projects_sharepointold
    name 192.168.2.2 isa_server_outside
    interface Ethernet0/0
    nameif outside
    security-level 0
    ip address IncomingIP 255.255.255.248
    interface Ethernet0/1
    nameif inside
    security-level 100
    ip address 192.168.2.1 255.255.255.0
    interface Ethernet0/2
    shutdown
    no nameif
    no security-level
    no ip address
    interface Ethernet0/3
    shutdown
    no nameif
    no security-level
    no ip address
    interface Management0/0
    nameif management
    security-level 100
    ip address 192.168.1.253 255.255.255.0
    management-only
    passwd 123
    ftp mode passive
    clock timezone EEST 2
    clock summer-time EEDT recurring last Sun Mar 3:00 last Sun Oct 4:00
    object-group service TCP_8081 tcp
    port-object eq 8081
    object-group service DM_INLINE_TCP_1 tcp
    port-object eq 3389
    port-object eq ftp
    port-object eq www
    port-object eq https
    port-object eq smtp
    port-object eq pop3
    port-object eq 3200
    port-object eq 3300
    port-object eq 3600
    port-object eq 3299
    port-object eq 3390
    port-object eq 50000
    port-object eq 3396
    port-object eq 3397
    port-object eq 3398
    port-object eq imap4
    port-object eq 587
    port-object eq 993
    port-object eq 8000
    port-object eq 8443
    port-object eq telnet
    port-object eq 3901
    group-object TCP_8081
    port-object eq 1433
    port-object eq 3391
    port-object eq 3399
    port-object eq 8080
    port-object eq 3128
    port-object eq 3900
    port-object eq 3902
    port-object eq 7777
    port-object eq 3392
    port-object eq 3393
    port-object eq 3394
    port-object eq 3395
    port-object eq 92
    port-object eq 91
    port-object eq 3206
    port-object eq 8001
    port-object eq 8181
    port-object eq 7778
    port-object eq 8180
    port-object eq 22222
    port-object eq 11001
    port-object eq 11002
    port-object eq 1555
    port-object eq 2223
    port-object eq 2224
    object-group service RDP tcp
    port-object eq 3389
    object-group service 3901 tcp
    description 3901
    port-object eq 3901
    object-group service 50000 tcp
    description 50000
    port-object eq 50000
    object-group service Enable_Transparent_Tunneling_UDP udp
    port-object eq 4500
    access-list inside_access_in remark connection to SAP
    access-list inside_access_in extended permit ip 192.168.2.0 255.255.255.0 host SAP_router_IP_on_SAP
    access-list inside_access_in remark VPN Outgoing - PPTP
    access-list inside_access_in extended permit tcp 192.168.2.0 255.255.255.0 any eq pptp
    access-list inside_access_in remark VPN Outgoing - GRE
    access-list inside_access_in extended permit gre 192.168.2.0 255.255.255.0 any
    access-list inside_access_in remark VPN - GRE
    access-list inside_access_in extended permit gre any any
    access-list inside_access_in remark VPN Outgoing - IKE Client
    access-list inside_access_in extended permit udp 192.168.2.0 255.255.255.0 any eq isakmp
    access-list inside_access_in remark VPN Outgoing - IPSecNAT - T
    access-list inside_access_in extended permit udp 192.168.2.0 255.255.255.0 any eq 4500
    access-list inside_access_in remark DNS Outgoing
    access-list inside_access_in extended permit udp any any eq domain
    access-list inside_access_in remark DNS Outgoing
    access-list inside_access_in extended permit tcp any any eq domain
    access-list inside_access_in remark Outoing Ports
    access-list inside_access_in extended permit tcp 192.168.2.0 255.255.255.0 any object-group DM_INLINE_TCP_1
    access-list inside_access_in extended permit ip 172.16.1.0 255.255.255.0 any
    access-list outside_access_in extended permit ip any any
    access-list outside_access_in extended permit tcp any any eq pptp
    access-list outside_access_in extended permit gre any any
    access-list outside_access_in extended permit gre any host Mail_Server
    access-list outside_access_in extended permit tcp any host Mail_Server eq pptp
    access-list outside_access_in extended permit esp any any
    access-list outside_access_in extended permit ah any any
    access-list outside_access_in extended permit udp any any eq isakmp
    access-list outside_access_in extended permit udp any any object-group Enable_Transparent_Tunneling_UDP
    access-list VPN standard permit 192.168.2.0 255.255.255.0
    access-list corp_vpn extended permit ip 192.168.2.0 255.255.255.0 172.16.1.0 255.255.255.0
    pager lines 24
    logging enable
    logging asdm informational
    mtu outside 1500
    mtu inside 1500
    mtu management 1500
    ip local pool POOL 172.16.1.10-172.16.1.20 mask 255.255.255.0
    no failover
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-603.bin
    no asdm history enable
    arp timeout 14400
    nat-control
    global (outside) 2 Mail_Server netmask 255.0.0.0
    global (outside) 1 interface
    global (inside) 2 interface
    nat (inside) 0 access-list corp_vpn
    nat (inside) 1 0.0.0.0 0.0.0.0
    static (inside,outside) tcp Mail_Server 8001 ISA_Server_second_external_IP 8001 netmask 255.255.255.255
    static (inside,outside) tcp Mail_Server 8000 ISA_Server_second_external_IP 8000 netmask 255.255.255.255
    static (inside,outside) tcp Mail_Server pptp isa_server_outside pptp netmask 255.255.255.255
    static (inside,outside) tcp Mail_Server smtp isa_server_outside smtp netmask 255.255.255.255
    static (inside,outside) tcp Mail_Server 587 isa_server_outside 587 netmask 255.255.255.255
    static (inside,outside) tcp Mail_Server 9444 isa_server_outside 9444 netmask 255.255.255.255
    static (inside,outside) tcp Mail_Server 9443 isa_server_outside 9443 netmask 255.255.255.255
    static (inside,outside) tcp Mail_Server 3389 isa_server_outside 3389 netmask 255.255.255.255
    static (inside,outside) tcp Mail_Server 3390 isa_server_outside 3390 netmask 255.255.255.255
    static (inside,outside) tcp Mail_Server 3901 isa_server_outside 3901 netmask 255.255.255.255
    static (inside,outside) tcp SAP 50000 isa_server_outside 50000 netmask 255.255.255.255
    static (inside,outside) tcp SAP 3200 isa_server_outside 3200 netmask 255.255.255.255
    static (inside,outside) tcp SAP 3299 isa_server_outside 3299 netmask 255.255.255.255
    static (inside,outside) tcp Mail_Server www isa_server_outside www netmask 255.255.255.255
    static (inside,outside) tcp Mail_Server https isa_server_outside https netmask 255.255.255.255
    static (inside,outside) tcp Mail_Server pop3 isa_server_outside pop3 netmask 255.255.255.255
    static (inside,outside) tcp Mail_Server imap4 isa_server_outside imap4 netmask 255.255.255.255
    static (inside,outside) tcp cms_eservices_projects_sharepointold 9999 isa_server_outside 9999 netmask 255.255.255.255
    static (inside,outside) 192.168.2.0  access-list corp_vpn
    access-group outside_access_in in interface outside
    access-group inside_access_in in interface inside
    route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout uauth 0:05:00 absolute
    dynamic-access-policy-record DfltAccessPolicy
    http server enable
    http 192.168.2.0 255.255.255.0 inside
    http 192.168.1.0 255.255.255.0 management
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set transet esp-des esp-md5-hmac
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto dynamic-map dynmap 10 set pfs
    crypto dynamic-map dynmap 10 set transform-set transet ESP-3DES-SHA
    crypto map cryptomap 10 ipsec-isakmp dynamic dynmap
    crypto map cryptomap interface outside
    crypto isakmp identity address
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash md5
    group 2
    lifetime 86400
    crypto isakmp policy 30
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    no crypto isakmp nat-traversal
    telnet 192.168.2.0 255.255.255.0 inside
    telnet 192.168.1.0 255.255.255.0 management
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    dhcpd dns xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx interface inside
    dhcpd domain domain.local interface inside
    threat-detection basic-threat
    threat-detection statistics host
    threat-detection statistics access-list
    tftp-server management 192.168.1.123 /
    group-policy mypolicy internal
    group-policy mypolicy attributes
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value VPN
    username vpdn password 123
    username vpdn attributes
    vpn-group-policy mypolicy
    service-type remote-access
    tunnel-group mypolicy type remote-access
    tunnel-group mypolicy general-attributes
    address-pool POOL
    default-group-policy mypolicy
    tunnel-group mypolicy ipsec-attributes
    pre-shared-key *
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect pptp
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:b8bb19b6cb05cfa9ee125ad7bc5444ac
    : end
    Thank you very much.

    Here is the output:
    ciscoasa# packet-tracer input outside icmp 172.16.1.10 8 0 192.168.2.1
    Phase: 1
    Type: FLOW-LOOKUP
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Found no matching flow, creating a new flow
    Phase: 2
    Type: UN-NAT
    Subtype: static
    Result: ALLOW
    Config:
    static (inside,outside) 192.168.2.0  access-list corp_vpn
    nat-control
      match ip inside 192.168.2.0 255.255.255.0 outside 172.16.1.0 255.255.255.0
        static translation to 192.168.2.0
        translate_hits = 0, untranslate_hits = 139
    Additional Information:
    NAT divert to egress interface inside
    Untranslate 192.168.2.0/0 to 192.168.2.0/0 using netmask 255.255.255.0
    Phase: 3
    Type: ACCESS-LIST
    Subtype: log
    Result: ALLOW
    Config:
    access-group outside_access_in in interface outside
    access-list outside_access_in extended permit ip any any
    Additional Information:
    Phase: 4
    Type: IP-OPTIONS
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Phase: 5
    Type: CP-PUNT
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Phase: 6
    Type: INSPECT
    Subtype: np-inspect
    Result: ALLOW
    Config:
    class-map inspection_default
    match default-inspection-traffic
    policy-map global_policy
    class inspection_default
      inspect icmp
    service-policy global_policy global
    Additional Information:
    Phase: 7
    Type: INSPECT
    Subtype: np-inspect
    Result: ALLOW
    Config:
    Additional Information:
    Phase: 8
    Type: VPN
    Subtype: ipsec-tunnel-flow
    Result: ALLOW
    Config:
    Additional Information:
    Phase: 9
    Type: NAT-EXEMPT
    Subtype: rpf-check
    Result: ALLOW
    Config:
    Additional Information:
    Phase: 10
    Type: NAT
    Subtype: rpf-check
    Result: ALLOW
    Config:
    static (inside,outside) 192.168.2.0  access-list corp_vpn
    nat-control
      match ip inside 192.168.2.0 255.255.255.0 outside 172.16.1.0 255.255.255.0
        static translation to 192.168.2.0
        translate_hits = 0, untranslate_hits = 140
    Additional Information:
    Phase: 11
    Type: ACCESS-LIST
    Subtype:
    Result: DROP
    Config:
    Implicit Rule
    Additional Information:
    Result:
    input-interface: outside
    input-status: up
    input-line-status: up
    output-interface: inside
    output-status: up
    output-line-status: up
    Action: drop
    Drop-reason: (acl-drop) Flow is denied by configured rule

  • How do I install Mac OSX Lion client on the new Mac Mini Server?

    If Apple would have had the quad-core processor option for the non-server Mac Mini, I would have just bought that, but I wanted the quad-core. I do not, however, need the server software. I found this article talking about how to disable the server functionality, but this article highlights how little that method actually does.
    Ultimately, I just want to do a clean reinstall like I used to do prior to Lion. This process used to be so easy. Create a disk image of the desired operating system on USB, option boot, and you're done. Now it appears that Apple purposely impedes this process, as every time I boot from the USB I created with Mac OSX Lion client, I get a circle with a line through it. Is there any way around this restriction? Editing firmware, editing .plist files, etc?
    Very disappointed that Apple is limiting what used to be such a simple process on Hardware and Software that I paid for but now can't get the functionality I want.

    Sorry to be the bearer of bad news, but what I don't think you can do what you're asking for.  Closest thing is going to be disabling the server components like it says in the article, but again, that doesn't do much.

  • WLC 4402 Multiple clients can connect to AP but only one gets an IP

    I have a 4402 which is connected to a 4506 Switch int Gig 3/1 via a trunk port. The Managment and AP-manger interfaces are on vlan 6
    interface GigabitEthernet3/1
    description Trunk Port to WLC
    switchport trunk encapsulation dot1q
    switchport trunk allowed vlan 2-6
    switchport mode trunk
    end
    I have a 1142N AP also connected to the switch and it pulls a DHCP IP Address and configs etc and registers to the WLC. It too is on Vlan 6 and it is connected to the 4506 on int gig 4/33 which is an access port.
    interface GigabitEthernet4/33
    description Access port to Cisco LAP 1142
    switchport access vlan 6
    switchport mode access
    end
    My router is my dhcp server;
    ip dhcp pool wlanmantraffic
       network 10.6.0.0 255.255.255.0
       default-router 10.6.0.1
       dns-server 66.109.38.250 10.7.0.8
       option 43 hex f104.3130.2e36.2e30.2e33
    interface FastEthernet0/1.6
    description Vlan6
    encapsulation dot1Q 6
    ip address 10.6.0.1 255.255.255.0
    no ip redirects
    no ip unreachables
    no ip proxy-arp
    ip nat inside
    ip virtual-reassembly
    I am doing local authentication, so i have added users to the WLC
    My problem is that the first client that connected was able to get an IP address and connect to anything internal and external.
    I then connected another client on another laptop and that client could connect but not get an IP address, it  just self assigned.
    When i look at the clients i can see the MAC address of both Clients on the WLC, but doing a show mac address-table dynamic i only see the MAC of the client that works properly. The client that doesnt get an IP has no entry in the 4506 switch.
    I am stumped, from what I understand, is that the 2nd clients traffic is being trunked to the WLC , hence it has the MAC address. But I dont know why its not getting a DHCP assigned IP address.
    Thanks in advance for your help.

    Here is some of the WLC config,
    (Cisco Controller) >show run-config
    Press Enter to continue...
    System Inventory
    NAME: "Chassis"    , DESCR: "4400 Series WLAN Controller:25 APs"
    PID: AIR-WLC4402-25-K9,  VID: V02,  SN: FOCblankedbyme
    Burned-in MAC Address............................ 00:07:0E:55:FA:C0
    Crypto Accelerator 1............................. Absent
    Crypto Accelerator 2............................. Absent
    Power Supply 1................................... Absent
    Power Supply 2................................... Present, OK
    Maximum number of APs supported.................. 25
    Press Enter to continue or to abort
    System Information
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.0.235.3
    RTOS Version..................................... 7.0.235.3
    Bootloader Version............................... 7.0.235.3
    Emergency Image Version.......................... 7.0.235.3
    Build Type....................................... DATA + WPS
    System Name...................................... CISCO-LWAPP-CONTROLLER
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.14179.1.1.4.3
    IP Address....................................... 10.6.0.3
    System Up Time................................... 0 days 21 hrs 7 mins 20 secs
    System Timezone Location......................... (GMT -5:00) Eastern Time (US a
    nd Canada)
    Configured Country............................... US  - United States
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +36 C
    --More or (q)uit current module or to abort
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 1
    Number of Active Clients......................... 3
    Burned-in MAC Address............................ 00:07:0E:55:FA:C0
    Crypto Accelerator 1............................. Absent
    Crypto Accelerator 2............................. Absent
    Power Supply 1................................... Absent
    Power Supply 2................................... Present, OK
    Maximum number of APs supported.................. 25
    Press Enter to continue or to abort
    AP Bundle Information
    Primary AP Image        Size
    ap3g1                   6672
    ap801                   5180
    ap802                   5220
    c1100                   3092
    c1130                   4960
    c1140                   4980
    c1200                   3360
    c1240                   4800
    c1250                   5500
    c1310                   3132
    c1520                   6400
    c3201                   4312
    c602i                   3712
    Secondary AP Image      Size
    ap801                   4952
    c1100                   3040
    --More or (q)uit current module or to abort
    c1130                   4880
    c1140                   4492
    c1200                   3312
    c1240                   4712
    c1250                   5060
    c1310                   3080
    c1520                   5240
    c3201                   4260
    Press Enter to continue or to abort
    Switch Configuration
    802.3x Flow Control Mode......................... Disable
    FIPS prerequisite features....................... Disabled
    secret obfuscation............................... Enabled
    Strong Password Check Features:
             case-check ...........Enabled
             consecutive-check ....Enabled
             default-check .......Enabled
             username-check ......Enabled
    Press Enter to continue or to abort
    Network Information
    RF-Network Name............................. RFMobile
    Web Mode.................................... Disable
    Secure Web Mode............................. Enable
    Secure Web Mode Cipher-Option High.......... Disable
    Secure Web Mode Cipher-Option SSLv2......... Enable
    OCSP........................................ Disabled
    OCSP responder URL..........................
    Secure Shell (ssh).......................... Enable
    Telnet...................................... Disable
    Ethernet Multicast Forwarding............... Disable
    Ethernet Broadcast Forwarding............... Disable
    AP Multicast/Broadcast Mode................. Unicast
    IGMP snooping............................... Disabled
    IGMP timeout................................ 60 seconds
    IGMP Query Interval......................... 20 seconds
    User Idle Timeout........................... 300 seconds
    ARP Idle Timeout............................ 300 seconds
    Cisco AP Default Master..................... Enabled
    AP Join Priority............................ Disable
    Mgmt Via Wireless Interface................. Disable
    Mgmt Via Dynamic Interface.................. Disable
    --More or (q)uit current module or to abort
    Bridge MAC filter Config.................... Enable
    Bridge Security Mode........................ EAP
    Mesh Full Sector DFS........................ Enable
    Apple Talk ................................. Disable
    AP Fallback ................................ Enable
    Web Auth Redirect Ports .................... 80
    Web Auth Proxy Redirect  ................... Disable
    Fast SSID Change ........................... Disabled
    802.3 Bridging ............................. Disable
    IP/MAC Addr Binding Check .................. Enabled
    Press Enter to continue or to abort
    Port Summary
               STP   Admin   Physical   Physical   Link   Link    Mcast
    Pr  Type   Stat   Mode     Mode      Status   Status  Trap   Appliance   POE
    1  Normal  Forw Enable  Auto       1000 Full  Up     Enable  Enable     N/A
    2  Normal  Forw Enable  Auto       1000 Full  Up     Enable  Enable     N/A
    Press Enter to continue or to abort
    AP Summary
    Number of APs.................................... 1
    Global AP User Name.............................. Not Configured
    Global AP Dot1x User Name........................ Not Configured
    AP Name             Slots  AP Model              Ethernet MAC       Location
          Port  Country  Priority
    NOSC-N-B1917-AP01    2     AIR-LAP1142N-A-K9     00:22:bd:1b:34:5a         Route
    23B  1        US       1
    AP Tcp-Mss-Adjust Info
    AP Name              TCP State  MSS Size
    NOSC-N-B1917-AP01    disabled   -
    Press Enter to continue or to abort
    AP Location
    Total Number of AP Groups........................ 0
    Site Name........................................ default-group
    Site Description.................................
    WLAN ID          Interface          Network Admission Control          Radio Pol
    icy
    1               management           Disabled                          None
    AP Name             Slots  AP Model             Ethernet MAC       Location
         Port  Country  Priority
    NOSC-N-B1917-AP01    2     AIR-LAP1142N-A-K9    00:22:bd:1b:34:5a         Route
    23B  1     US       1
    Press Enter to continue or to abort
    AP Config
    Cisco AP Identifier.............................. 6
    Cisco AP Name.................................... NOSC-N-B1917-AP01
    Country code..................................... US  - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US  - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:22:bd:1b:34:5a
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.6.0.26
    Gateway IP Addr.................................. 10.6.0.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Enabled
    Ssh State........................................ Enabled
    Cisco AP Location................................ Route 23B
    Cisco AP Group Name.............................. default-group
    Primary Cisco Switch Name........................
    Primary Cisco Switch IP Address.................. Not Configured
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    --More or (q)uit current module or to abort... Not Configured
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W  Version .................................... 7.0.235.3
    Boot  Version ................................... 12.4.18.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Disabled
    PoE Power Injector MAC Addr...................... Disabled
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1142N-A-K9
    AP Image......................................... C1140-K9W8-M
    IOS Version...................................... 12.4(23c)JA6
    --More or (q)uit current module or to abort
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX1337SA7D
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
            Native ID :..................................... 6
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... CUSTOMIZED
    AP User Name..................................... danielott
    AP Dot1x User Mode............................... CUSTOMIZED
    AP Dot1x User Name............................... danielott
    Cisco AP system logging host..................... 255.255.255.255
    AP Up Time....................................... 0 days, 19 h 22 m 53 s
    AP LWAPP Up Time................................. 0 days, 01 h 08 m 46 s
    Join Date and Time............................... Mon Nov  5 16:17:51 2012
    Join Taken Time.................................. 0 days, 00 h 00 m 12 s
    Attributes for Slot  0
        Radio Type................................... RADIO_TYPE_80211n-2.4
    --More or (q)uit current module or to abort
        Administrative State ........................ ADMIN_ENABLED
        Operation State ............................. UP
        Radio Role .................................. ACCESS
        CellId ...................................... 0
        Station Configuration
          Configuration ............................. AUTOMATIC
          Number Of WLANs ........................... 1
          Medium Occupancy Limit .................... 100
          CFP Period ................................ 4
          CFP MaxDuration ........................... 60
          BSSID ..................................... 00:27:0d:07:cb:e0
          Operation Rate Set
            1000 Kilo Bits........................... MANDATORY
            2000 Kilo Bits........................... MANDATORY
            5500 Kilo Bits........................... MANDATORY
            11000 Kilo Bits.......................... MANDATORY
            6000 Kilo Bits........................... SUPPORTED
            9000 Kilo Bits........................... SUPPORTED
            12000 Kilo Bits.......................... SUPPORTED
            18000 Kilo Bits.......................... SUPPORTED
            24000 Kilo Bits.......................... SUPPORTED
            36000 Kilo Bits.......................... SUPPORTED
    --More or (q)uit current module or to abort
            48000 Kilo Bits.......................... SUPPORTED
            54000 Kilo Bits.......................... SUPPORTED
          MCS Set
            MCS 0.................................... SUPPORTED
            MCS 1.................................... SUPPORTED
            MCS 2.................................... SUPPORTED
            MCS 3.................................... SUPPORTED
            MCS 4.................................... SUPPORTED
            MCS 5.................................... SUPPORTED
            MCS 6.................................... SUPPORTED
            MCS 7.................................... SUPPORTED
            MCS 8.................................... SUPPORTED
            MCS 9.................................... SUPPORTED
            MCS 10................................... SUPPORTED
            MCS 11................................... SUPPORTED
            MCS 12................................... SUPPORTED
            MCS 13................................... SUPPORTED
            MCS 14................................... SUPPORTED
            MCS 15................................... SUPPORTED
          Beacon Period ............................. 100
          Fragmentation Threshold ................... 2346
          Multi Domain Capability Implemented ....... TRUE
          Multi Domain Capability Enabled ........... TRUE
          Country String ............................ US
        Multi Domain Capability
          Configuration ............................. AUTOMATIC
          First Chan Num ............................ 1
          Number Of Channels ........................ 11
        MAC Operation Parameters
          Configuration ............................. AUTOMATIC
          Fragmentation Threshold ................... 2346
          Packet Retry Limit ........................ 64
        Tx Power
          Num Of Supported Power Levels ............. 8
          Tx Power Level 1 .......................... 20 dBm
          Tx Power Level 2 .......................... 17 dBm
          Tx Power Level 3 .......................... 14 dBm
          Tx Power Level 4 .......................... 11 dBm
          Tx Power Level 5 .......................... 8 dBm
          Tx Power Level 6 .......................... 5 dBm
          Tx Power Level 7 .......................... 2 dBm
          Tx Power Level 8 .......................... -1 dBm
          Tx Power Configuration .................... AUTOMATIC
    --More or (q)uit current module or to abort
          Current Tx Power Level .................... 1
        Phy OFDM parameters
          Configuration ............................. AUTOMATIC
          Current Channel ........................... 1
          Extension Channel ......................... NONE
          Channel Width.............................. 20 Mhz
          Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
          TI Threshold .............................. -50
          Legacy Tx Beamforming Configuration ....... AUTOMATIC
          Legacy Tx Beamforming ..................... DISABLED
          Antenna Type............................... INTERNAL_ANTENNA
          Internal Antenna Gain (in .5 dBi units).... 8
          Diversity.................................. DIVERSITY_ENABLED
          802.11n Antennas
             A....................................... ENABLED
             B....................................... ENABLED
             C....................................... ENABLED
        Performance Profile Parameters
          Configuration ............................. AUTOMATIC
          Interference threshold..................... 10 %
          Noise threshold............................  -70 dBm
    --More or (q)uit current module or to abort
          RF utilization threshold................... 80 %
          Data-rate threshold........................ 1000000 bps
          Client threshold........................... 12 clients
          Coverage SNR threshold..................... 12 dB
          Coverage exception level................... 25 %
          Client minimum exception level............. 3 clients
        Rogue Containment Information
        Containment Count............................ 0
        CleanAir Management Information
            CleanAir Capable......................... No
    Cisco AP Identifier.............................. 6
    Cisco AP Name.................................... NOSC-N-B1917-AP01
    Country code..................................... US  - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US  - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:22:bd:1b:34:5a
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.6.0.26
    Gateway IP Addr.................................. 10.6.0.1
    --More or (q)uit current module or to abort
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Enabled
    Ssh State........................................ Enabled
    Cisco AP Location................................ Route 23B
    Cisco AP Group Name.............................. default-group
    Primary Cisco Switch Name........................
    Primary Cisco Switch IP Address...............Secondary Cisco Switch Name.......
    Secondary Cisco Switch IP Address................ Not Configured
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W  Version .................................... 7.0.235.3
    Boot  Version ................................... 12.4.18.0
    Mini IOS Version ................................ 3.0.51.0
    --More or (q)uit current module or to abort
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Disabled
    PoE Power Injector MAC Addr...................... Disabled
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1142N-A-K9
    AP Image......................................... C1140-K9W8-M
    IOS Version...................................... 12.4(23c)JA6
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX1337SA7D
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
            Native ID :..................................... 6
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... CUSTOMIZED
    AP User Name..................................... danielott
    AP Dot1x User Mode............................... CUSTOMIZED
    AP Dot1x User Name............................... danielott
    --More or (q)uit current module or to abort
    Cisco AP system logging host..................... 255.255.255.255
    AP Up Time....................................... 0 days, 19 h 22 m 53 s
    AP LWAPP Up Time................................. 0 days, 01 h 08 m 46 s
    Join Date and Time............................... Mon Nov  5 16:17:51 2012
    Join Taken Time.................................. 0 days, 00 h 00 m 12 s
    Attributes for Slot  1
        Radio Type................................... RADIO_TYPE_80211n-5
        Radio Subband................................ RADIO_SUBBAND_ALL
        Administrative State ........................ ADMIN_ENABLED
        Operation State ............................. UP
        Radio Role .................................. ACCESS
        CellId ...................................... 0
        Station Configuration
          Configuration ............................. AUTOMATIC
          Number Of WLANs ........................... 1
          Medium Occupancy Limit .................... 100
          CFP Period ................................ 4
          CFP MaxDuration ........................... 60
          BSSID ..................................... 00:27:0d:07:cb:e0
          Operation Rate Set
    --More or (q)uit current module or to abort
            6000 Kilo Bits........................... MANDATORY
            9000 Kilo Bits........................... SUPPORTED
            12000 Kilo Bits.......................... MANDATORY
            18000 Kilo Bits.......................... SUPPORTED
            24000 Kilo Bits.......................... MANDATORY
            36000 Kilo Bits.......................... SUPPORTED
            48000 Kilo Bits.......................... SUPPORTED
            54000 Kilo Bits.......................... SUPPORTED
          MCS Set
            MCS 0.................................... SUPPORTED
            MCS 1.................................... SUPPORTED
            MCS 2.................................... SUPPORTED
            MCS 3.................................... SUPPORTED
            MCS 4.................................... SUPPORTED
            MCS 5.................................... SUPPORTED
            MCS 6.................................... SUPPORTED
            MCS 7.................................... SUPPORTED
            MCS 8.................................... SUPPORTED
            MCS 9.................................... SUPPORTED
            MCS 10................................... SUPPORTED
            MCS 11................................... SUPPORTED
            MCS 12................................... SUPPORTED
            MCS 13................................... SUPPORTED
    --More or (q)uit current module or to abort
            MCS 14................................... SUPPORTED
            MCS 15................................... SUPPORTED
          Beacon Period ............................. 100
          Fragmentation Threshold ................... 2346
          Multi Domain Capability Implemented ....... TRUE
          Multi Domain Capability Enabled ........... TRUE
          Country String ............................ US
        Multi Domain Capability
          Configuration ............................. AUTOMATIC
          First Chan Num ............................ 36
          Number Of Channels ........................ 21
        MAC Operation Parameters
          Configuration ............................. AUTOMATIC
          Fragmentation Threshold ................... 2346
          Packet Retry Limit ........................ 64
        Tx Power
          Num Of Supported Power Levels ............. 7
          Tx Power Level 1 .......................... 17 dBm
          Tx Power Level 2 .......................... 14 dBm
          Tx Power Level 3 .......................... 11 dBm
    --More or (q)uit current module or to abort
          Tx Power Level 4 .......................... 8 dBm
          Tx Power Level 5 .......................... 5 dBm
          Tx Power Level 6 .......................... 2 dBm
          Tx Power Level 7 .......................... -1 dBm
          Tx Power Configuration .................... AUTOMATIC
          Current Tx Power Level .................... 1
        Phy OFDM parameters
          Configuration ............................. AUTOMATIC
          Current Channel ........................... 161
          Extension Channel ......................... NONE
          Channel Width.............................. 20 Mhz
          Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
            ......................................... 104,108,112,116,132,136,140,
            ......................................... 149,153,157,161,165
          TI Threshold .............................. -50
          Legacy Tx Beamforming Configuration ....... AUTOMATIC
          Legacy Tx Beamforming ..................... DISABLED
          Antenna Type............................... INTERNAL_ANTENNA
          Internal Antenna Gain (in .5 dBi units).... 8
          Diversity.................................. DIVERSITY_ENABLED
          802.11n Antennas
             A....................................... ENABLED
    --More or (q)uit current module or to abort
             B....................................... ENABLED
             C....................................... ENABLED
        Performance Profile Parameters
          Configuration ............................. AUTOMATIC
          Interference threshold..................... 10 %
          Noise threshold............................  -70 dBm
          RF utilization threshold................... 80 %
          Data-rate threshold........................ 1000000 bps
          Client threshold........................... 12 clients
          Coverage SNR threshold..................... 16 dB
          Coverage exception level................... 25 %
          Client minimum exception level............. 3 clients
        Rogue Containment Information
        Containment Count............................ 0
        CleanAir Management Information
            CleanAir Capable......................... No

  • Windows VNC clients cannot connect to Snow Leopard Server native VNC server

    I am resurfacing the following related comment made in another post that discusses the same issue I am having with VNC on Snow Leopard. This is still an issue and I cannot connect to our Xserve's Snow Leopard Server with a VNC client on Windows.
    I don't want to install another third party VNC server onto our SL Server, and am looking for a VNC client for windows that will connect to our SL Server.
    Does anyone have any solutions?
    == QUOTED TEXT BELOW ==
    Re: Newbie: Connect Windows -> OSX Server
    Posted: Nov 4, 2009 9:26 AM in response to: Antonio Rocco
    I would politely disagree. Yes, definitely, the Mac 'Screen Sharing' app works a treat, and Apple Remote Desktop.app works as well, but I am coming from a Window's PeeCee.
    For me, connecting to my 10.5(.8) Server via tightvnc gives 'Server did not offer supported security type!". Using RealVNC to this machine states "No matching security types Do you wish to reconnect to ... ?" a telnet to this AppleVNCServer service (port 5900), shows RFB 003.889 *, or Remote Frame Buffer Major 3, minor 889.
    Also, connecting to multiple 10.6(.1) Clients with Tightvnc correctly asks for a password but then hangs at "Status: Security type requested". Using RealVNC opens, connects, asks for authentication, and exits. Telneting to this AppleVNCServer service (port 5900), also shows RFB 003.889 *.
    The Current Version of the protocol is supposed to be 3.8, that is Major version 3, minor version 8. Not 80 or 800 but Eight). http://www.realvnc.com/docs/rfbproto.pdf and I believe that tightvnc only supports up to version 3.7.
    On each station I have installed the 'old' OSXVnc.app as a service (to a unique port). OSXVnc utilizes protocol 3.3 and I can control them successfully, but that is of my own doing because of this issue.
    Now JollysFastVNC works a treat to any machine I have EVER tried to connect to. I have not tried COTVNC or any of the others (too slow for me, when they wer e around)
    Also, I just noticed that RealVNC states that their free and personal version will not connect to Mac OSX (x86 and PPC) but the Enterprise one will. I just Dl'ed the Enterprise Viewer and it gave essentially the same thing ('protocol is not valid' message, even after it asks for a password). Anyway, I am not here to hijack this thread, just trying to keep the info flowing and open.
    Maybe I am the only one with these problems but the bottom line is I cannot use Real or Tight, or UltraVNC to administer my server or clients as long as AppleVNCServer gives out the 003.889 protocol version.
    Peter
    * The ProtocolVersion message consists of 12 bytes interpreted as a string of ASCII characters in the format "RFB xxx.yyy\n" where xxx and yyy are the major and
    minor version numbers, padded with zeros.

    Searching on the net brought me to the same solution that Mr. Hoffman found as well, I was a bit skeptical at first but since he recommended it, and all my other attempts failed, it was a last resort and I have some additional notes of my own for a successful solution. Read the two links below first before doing anything, as they contribute to the solution in tandem.
    http://forums.macrumors.com/showpost.php?p=7221295&postcount=20
    http://forums.macrumors.com/showpost.php?p=9081641&postcount=28
    I should probably just create an entirely new post with all of the steps that worked for me, but it's rather straightforward nonetheless.

  • IChat in Lion unable to connect with a jabber server

    I have 3 Jabber accounts set up, one to a server my department is running, one to a server that another department at work is running, and a gmail account.  When I upgraded to Lion, I am unable to login to the server that the other department is running, the other two are working fine.  I can find a Snow Leopard machine and login just fine to that server.  Server logs from the other department show that there is an authentication error.  One of the admins running that server checked the logs it showed me connecting, auth failing, and disconnecting.  Not sure yet what server software they are running, but I do know its a Linux server, as is the one that my department is running.  I am trying to find out more details on that.
    Any changes to iChat that might lead to incompatibility issues with certain versions of jabber servers?
    I have tried removing and re-creating the jabber account and still no luck, as well as removing and re-importing the SSL certificate used by this server.
    Thanks....

    Just noticed this response.
    The server hasn't changed, and it is a linux server, not a Mac OS X server so not sure any of those communities would help.  It has required case sensitive passwords all along and there is a web interface for me to change the password that uses other athentication credentials than the jabber account.  One of the first things I did was to change the password to something different and try the new password.  It was after I had changed that password that I found a Snow Leopard machine and was able to login with the new password.
    I'm not sure if SSL is required on the server side, but SSL works from the Snow leopard machine and the account is configured to use SSL on port 5223 on both machines.
    -Tom
    Ralph Johns (UK) wrote:
    Hi,
    I am unaware of any changes on this front. (Partly as I don't have  Lion Capable machine)
    As it is somewhat server related I would pick a  Community from here
    iChat should connect on port 5222 or 5223 with SSL
    Most SSL servers don't respond to request on the 5222 port and vice versa (one or the other).
    I would also check the Password.  ( I  am wondering if a Upper case Character is present that is now sent as upper case when before this did not matter - or something similar along those lines)
    10:13 PM      Saturday; July 23, 2011
    Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro 2Gb( 10.6.8)
     Mac OS X (10.6.8),
    "Limit the Logs to the Bits above Binary Images."  No, Seriously

  • Ubuntu client flakey connection to  windows 7 server

    Hi.
    This is very strange, but:
    1) server is windows server, and I can connect to it via java app from another windows machine
    2) from ubuntu machine running client app, I can occassionally connect to the Windows Server.
    3) ubuntu server: Linux 2.6.24-24-server , running java version "1.6.0_24"
    4) windows server: Windows 2008 Server 64bit running Oracle 11g Release 11.2.0.1.0
    Both machines are on Subnet 10.* network and firewalls are down on subnet.
    I can ping each machine just fine.
    When I attempt to connect from ubuntu machine the connection DOES (always) show up in v$session on server, but client not is returned a connection (Yet occasionally does).
    I tried to turn on TNS tracing on server but couldn't see any tracing being done (tried setting in sqlnet.ora and listener.ora)
    trace_level_server = 10
    trace_file_server = server.trc
    trace_directory_server = <path_to_trace_dir>
    I also tried client side logging with using ojdbc6_g.jar and starting up the java prog like:
    java -Doracle.jdbc.Trace=true -Djava.util.logging.config.file=jdbc.properties
    jdbc.properties :
    .level=SEVERE
    oracle.jdbc.level=FINER
    oracle.jdbc.handlers=java.util.logging.FileHandler
    java.util.logging.FileHandler.level=FINER
    java.util.logging.FileHandler.pattern=jdbc.log
    java.util.logging.FileHandler.count=1
    java.util.logging.FileHandler.formatter=java.util.logging.SimpleFormatter
    But didn't get any tell-tale signs...
    Can anyone give me some suggestions to check on for A) the java program connectivity and/or B) the tracing problem on server?
    Thanks,
    Joel
    Edited by: rhinosi on Oct 26, 2011 8:39 PM

    This forum is dealing with connections from Oracle to foreign database using the gateway.
    For me it looks like you're having a JDBC connection issue which is better handled in this forum:
    https://forums.oracle.com/forums/category.jspa?categoryID=288
    If my understanding is correct, please close this thread and repost it in the JDBC forum.
    Thanks.

  • Does anyone have Lion and can connect to Windows servers?

    Is there anyone out there who can see the Windows server folders?  Or am I (and a handful of others) the only ones who are having this issue?  Is ANYBODY able to connect to their Windows server with Lion?  (they dropped SMB support in Lion...this is why I'm asking).

    What servers are you connecting to?  Here at work they use:
    windows server 2003
    standard edition
    32bit
    No luck with me.  I can connect to wifi internet, but can't access any of the shared folders anymore (I could with SL)

Maybe you are looking for

  • Upload Excel sheet using Data Integrator 6.1?

    hi all , Upload Excel sheet using Data Integrator? and how to create ODBC for the PC and jobserver i am using version 6.1? i am using excel as my one of the data source and tell me how to use different types of data sources in DI . after uploading th

  • Won't boot, recognise superdrive or startup in target disk mode

    I've been trying to help a friend with his iMac G4 that crashed. Of course he hasn't backed up his hard drive in years. I've searched the forums and have tried several methods to get his machine running or at least recover his data but with no luck.

  • All apps up to date, but not?

    This morning I hade 56 apps to update but now app store says that there all up to date. I have checked and found that the apps havn't been updated. I have restarted, synces, hard restarted and evn=en checked for updates on itunes. Anyone else having

  • Help! my scroll bar (elevator bar) is not showing up now--how can I fix it; it's driving me crazy!

    The scroll (elevator) bar has suddenly become very faint, hard, to find, and in some cases is not showing up at all. The arrows at the top and bottom show up, but not the scrolly tool itself. I have tried changing the themes/display, but it doesn't s

  • PLANT field hidden in MM06

    Hi gurus.. I do have a question about a field in initial screen of MM06 transaction (flag material master for deletion). In our system there is no PLANT field - or it is hidden, not quite sure about this. So If we want to display this PLANT field aga