LMS 3.2 on Solaris 10 - CatOS PVlan Mapping commands to MSFC not being saved by Ciscoworks

Question

Hi All,
We are doing some troubleshooting after the recovery of a Cat6500 Hybrid switch and we've encoutered something strange. It seems that Ciscoworks does not save the pvlan mapping statements applied to the MSFC (module 15 in this case). Below I have two excerpts. The first one is from an export of the latest saved config of a similar device. The other one is from the actual same switch.
Any ideas why this is happening?
Thanks
Jose Ribeiro
-bash-3.00$ cat ctspitdcemsw303-172-raw.cfg | grep mapping
#Macro-Port mapping
#vlan mapping
set pvlan mapping 2100 2101 1/7
set pvlan mapping 2100 2103 1/7
set pvlan mapping 2100 2104 1/7
set pvlan mapping 2100 2106 1/7
set pvlan mapping 2100 2109 1/7
set pvlan mapping 2600 2603 5/11-12
set pvlan mapping 2600 2604 5/11-12
set pvlan mapping 2800 2801 5/4
set pvlan mapping 2800 2802 5/4
set pvlan mapping 2800 2803 5/4
set pvlan mapping 2800 2804 5/4
set pvlan mapping 2800 2805 5/4
set pvlan mapping 2800 2806 5/4
set pvlan mapping 2800 2807 5/4
set pvlan mapping 2800 2808 5/4
set pvlan mapping 2800 2809 5/4
set pvlan mapping 2300 2303 9/31
set pvlan mapping 2300 2304 9/31
set pvlan mapping 2600 2603 9/28
set pvlan mapping 2600 2604 9/28
-bash-3.00$
ctspitdcemsw303> (enable) sh runn | incl mapping
set pvlan mapping 2100 2101 1/7
set pvlan mapping 2100 2103 1/7
set pvlan mapping 2100 2104 1/7
set pvlan mapping 2100 2106 1/7
set pvlan mapping 2100 2109 1/7
set pvlan mapping 2600 2603 5/11-12
set pvlan mapping 2600 2604 5/11-12
set pvlan mapping 2800 2801 5/4
set pvlan mapping 2800 2802 5/4
set pvlan mapping 2800 2803 5/4
set pvlan mapping 2800 2804 5/4
set pvlan mapping 2800 2805 5/4
set pvlan mapping 2800 2806 5/4
set pvlan mapping 2800 2807 5/4
set pvlan mapping 2800 2808 5/4
set pvlan mapping 2800 2809 5/4
set pvlan mapping 2300 2303 9/31
set pvlan mapping 2300 2304 9/31
set pvlan mapping 2600 2603 9/28
set pvlan mapping 2600 2604 9/28
set pvlan mapping 2300 2303 10/35-36
set pvlan mapping 2300 2304 10/35-36
set pvlan mapping 2300 2305 10/35-36
set pvlan mapping 2300 2309 10/35-36
set pvlan mapping 2300 2303 11/34
set pvlan mapping 2300 2304 11/34
set pvlan mapping 2600 2603 11/12-13,11/38-39
set pvlan mapping 2600 2604 11/12-13,11/38-39
set pvlan mapping 2300 2303 12/45-46
set pvlan mapping 2300 2304 12/45-46
set pvlan mapping 2600 2603 12/41-44
set pvlan mapping 2600 2604 12/41-44
set pvlan mapping 2000 2001 15/1
set pvlan mapping 2000 2002 15/1
set pvlan mapping 2000 2003 15/1
set pvlan mapping 2000 2005 15/1
set pvlan mapping 2000 2009 15/1
set pvlan mapping 2200 2201 15/1
set pvlan mapping 2200 2202 15/1
set pvlan mapping 2200 2203 15/1
set pvlan mapping 2200 2208 15/1
set pvlan mapping 2300 2301 15/1
set pvlan mapping 2300 2302 15/1
set pvlan mapping 2300 2303 15/1
set pvlan mapping 2300 2304 15/1
set pvlan mapping 2300 2305 15/1
set pvlan mapping 2300 2306 15/1
set pvlan mapping 2300 2307 15/1
set pvlan mapping 2300 2309 15/1
set pvlan mapping 2300 2312 15/1
set pvlan mapping 2500 2501 15/1
set pvlan mapping 2500 2503 15/1
set pvlan mapping 2600 2602 15/1
ctspitdcemsw303> (enable)

Answer 1

Hi Joseph,
When I run a write term I can see the whole switch config, though in pages (I need to hit enter several time to go trhu the whole config).
ctspitdcemsw303> (enable) write terminal
This command shows non-default configurations only.
Use 'write terminal all' to show both default and non-default configurations.
begin
# ***** NON-DEFAULT CONFIGURATION *****
#time: Mon May 9 2011, 09:08:46 EDT
#version 8.5(2)
Also a View Config Raw from Device Center shows configuration up to module 10, completely missing modules 11, 12 and 15 (pvlan mappings to the MSFC).
Thanks,
Jose