Location services shows wrong location

I have an iPhone 5 with latest iOS. I live in Kennesaw GA. I installed xfinity Internet at my new home.
When my phone is connected to wifi, it shows the current location as charleston SC. This is for any app that uses the GPS.
My wife has an iPhone 4S with latest iOS and her current location is correct when connected to wifi.
So I find it strange that my phone shows my current location as Charleston.
When I turn off the wifi, the current location is correct.
If anyone has experienced the same problem please respond.

Improving GPS accuracy
GPS accuracy varies depending on the number of visible GPS satellites. Locating all visible satellites can take several minutes, with accuracy gradually increasing over time. Use these tips to improve GPS accuracy:
Ensure the date, time, and time zone are correctly set on the device in Settings > General > Date & Time. If possible, use Set Automatically.
Important: Incorrect settings on your computer can sync to your device. Verify the date, time, and time zone on any computer that syncs with your device.
Restart your device.
Verify that you have a cellular or Wi-Fi network connection. This allows the Assisted GPS (A-GPS) on the device to locate visible GPS satellites faster, in addition to providing initial location information using the Wi-Fi or cellular networks.
Note: Microcells (sometimes called Femtocells) are not supported with Location Services.
Maintain a clear view of the horizon in several directions. Keep in mind that walls, vehicle roofs, tall buildings, mountains, and other obstructions can block line of sight to GPS satellites. When this occurs, your device will automatically use Wi-Fi or cellular networks to determine your position, until the GPS satellites are visible again.

Similar Messages

HT5594 Does location services show your actual address when at home

Does location services show your actual address when at home

I should also mention that my wife got a phone the same time I did. Sometimes her's will show the same problem, and then sometimes her's will work fine while mine is right next to her's and not working. This type of behavior would point to a problem with the device and not the service. But then the fact that mine DOES work at times would indicate a software/service issue. I've heard others say that behavior will change when WiFi is turned on or off or when airplane mode is turned off and on. I haven't really noticed that. It's a hard one to figure out. Hopefully it is something with the software/service that will simply be solved with updates.
Message was edited by: Fivepi

Reversal Document is Showing wrong figure in Service Tax Report

Hi All,
The data inconsistence in Service Tax Report.
The reversal documents are showing the excess amount while runnig the Service tax report.
Could you please help in finidng the reason and solution for this behaviour. All reversal documents are showing excess amounts in this case.
Thanks,
Nandu

Hi all,
The Tax transfer amount of reversal document should be Zero in ST Report and in Final GL. But the service tax report is showing wrong figures.
We reversed the tax transfer document to remove the wrong line from Serv. Tax Report as well as from Final GL.
As per the business requirement if any invoice and payment is wrongly done, that should be reversed.
Before reversal of this we need to reverse the tax transfer entry, then only we can reverse the payment as well as the Invoice.
Apart from this, If any other procedure please let me know in order to avoid errors in the service tax report
Regards,
Nandu

March 2013: I updated US Maps - it shows wrong tow...

I had the Nokia USA maps installed in my C6-01. It showd a lot of update and it finished with an error.
Then I realized that there is no US maps on my smartphone. So installed it again via PC.
Now it shows wrong town name but correct ZIP code
What should I do about it?
Solved!
Go to Solution.

Hi Thanks.
If I do that, what will happens to my stored GPS addresses?
I have previously downlaoded all of USA maps - how can I uninstall it from the SD card on the phone.
Surprisingly, when I expand the USA folder via Nokia Suite it lists all states and still lets me to download California maps - what is going on here?
Last time, when I was downloading Maps through a PC wirelessly, it showed an error. I didn't know that all US maps had gone - not knowing it, I tried to go to a location and it didn't work and it was showing German maps - if it is a corruption, it happened then - do I need start all over again? Then how can I still keep the saved addresses in the GPS (not the tel contacts) - you know there are two ways to save GPS addresses.
The only problem snce the update is all new addresses that I search for shows as:
1234 Emerson St, Santa Clara, CA, USA {note: Santa Clara is the county name and there is a city too - I entered Palo Alto and not Santa Clara)
Previously it would have shown as (exactly as I entered):
1234 Emerson St, Palo Alto, CA
The new display causing a lot of confusion.
Thanks for any suggestions.

[SOLVED] stellarium showing wrong objects positions

just stellarium showing wrong things, like the location or time are wrong...
i discover stellarium long time ago but i barely uses it, some time ago i remember that i see the moon in it and looking outside i can see the moon too! it was awesome, lately i noticed that the objects that i see in the program, say the moon, the sun, are not in the correct "place" for example right now here in argentina time is 08:40am and i see the sun like it was near midday, and i can say that now the moon never shows where it needs to be
I've set localtime to UTC when i installed arch, but i remember one time setting it to localtime and back to UTC but not remember why, besides i dont know the diference...
here's my rc.conf
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="en_US.utf8"
HARDWARECLOCK="UTC"
TIMEZONE="America/Buenos Aires"
KEYMAP="es"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# Scan hardware and load required modules at bootup
MOD_AUTOLOAD="yes"
# Module Blacklist - modules in this list will never be loaded by udev
MOD_BLACKLIST=()
# Modules to load at boot-up (in this order)
# - prefix a module with a ! to blacklist it
MODULES=(r8169 slhc snd-mixer-oss snd-pcm-oss snd-page-alloc snd-pcm snd-timer snd snd-hda-intel soundcore kqemu loop)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
HOSTNAME="aleyscha"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available
# interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# Note: to use DHCP, set your interface to be "dhcp" (eth0="dhcp")
lo="lo 127.0.0.1"
eth0="dhcp"
INTERFACES=(lo eth0)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network-profiles
#NET_PROFILES=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng iptables network netfs crond autofs fuse @fam @hal @alsa @clamav @avahi-daemon @gpm @sensors !postfix)
# End of file
B
Last edited by leo2501 (2008-10-15 03:07:04)

Just in case: Did you set your location correctly in stellarium? I noticed that the new version (0.10) reseted the settings.
BTW. UTC is time in GMT (e.g. London, England) and localtime is time wherever you are (Argentila I guess). If your clock is set to localtime and settings are for UTC it could be cause of your problems.
Last edited by jase (2008-10-13 07:02:16)

Lsnrctl Services === Showing 2 instances how come?

Service "Testdb" has 2 instance(s).
Instance "Testdbsid", status UNKNOWN, has 1 handler(s) for this service...
Handler(s):
"DEDICATED" established:0 refused:0
LOCAL SERVER
Instance "Testdbsid", status READY, has 1 handler(s) for this service...
Handler(s):
"DEDICATED" established:0 refused:0 state:ready
LOCAL SERVER
I have only one database "Testdb" and the sid is "TestdbSid".
How come the services showing [[Service "Testdb" has 2 instance(s).]]?
Correct me if im wrong.....
Each database will be having only one instance.
if we have two database then we will have 2 instances.
otherwise if we have two different homes(softwares) then each home will be having a database and each database will be having 1 instance.
In my case.....i dont know how these 2 instances came for a single database?
Thanks
Sathyguy

i tried but failed..... may be i might be wrong....
here is my "tnsname.ora"
# TNSNAMES.ORA Network Configuration File: c:\ora9i\network\admin\tnsnames.ora
# Generated by Oracle configuration tools.
EXTPROC_CONNECTION_DATA.TESTSRVR.LOCAL =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(CONNECT_DATA =
(SID = PLSExtProc)
(PRESENTATION = RO)
TESTDB.TESTSRVR.LOCAL =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = user-it-235)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = Testdb)
INST1_HTTP.TESTSRVR.LOCAL =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = user-it-235)(PORT = 1521))
(CONNECT_DATA =
(SERVER = SHARED)
(SERVICE_NAME = MODOSE)
(PRESENTATION = http://HRService)
and the listener.ora contains...
# LISTENER.ORA Network Configuration File: c:\ora9i\network\admin\listener.ora
# Generated by Oracle configuration tools.
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = user-it-235)(PORT = 1521))
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = c:\ora9i)
(PROGRAM = extproc)
(SID_DESC =
(GLOBAL_DBNAME = Testdb)
(ORACLE_HOME = c:\ora9i)
(SID_NAME = Testdbsid)
which part i have to comment?

Lenovo Solution Center Showing Wrong Warranty

I bought my Lenovo G500 laptop in December 2013. It has 1 year warranty. Today I installed Lenovo Solution Center and saw that it shows wrong warranty.
According to Lenovo Solution Center, the warranty is set to expire on September 22, 2014. But its wrong since I bought the laptop just around Christmas in 2013.
Solved!
Go to Solution.

Hi Mayank,
Welcome to Lenovo Community Forums!
There was an initial bug in LSC where extended warranty was not accurately shown and this was addressed in version 1.1.006. Several changes to the functionality of warranty lookup have been implemented in different versions of LSC to address other considerations.
In some cases, the Lenovo Solution Center is displaying a message, “Unable to determine warranty”, for the System and displaying a message, “not available”, for the Battery.
This could occur on any Lenovo system running Windows 7 or 8 and running LSC.
These will be solved in version 2.0.018 or higher of LSC.
Warranty status can be checked on the Lenovo support site at any time:
http://support.lenovo.com/en_IN/product-service/warranty-status/default.page?
Do post us back for further queries.
Best Regards
Shiva Kumar
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Can't login, shows wrong password.

hello everyone,
I'm using my skype account many years, and 30 minutes ago my skype closes and i was try to login again, but it shows wrong password, than i was going to reset new password, but mistake.. there was message something about .. i need to contact with skype support... i realy need my skype account back, beacuse i have many business people there and do this without reason i think its not the best skype idea.
What i must do to get back my skype account...?
Thank you!

Greetings,
Password-related matters must be resolved by Skype Customer Service; we here in the Community are not authorized to access Skype accountholder data. Although it may seem silly to do so, if you are locked out of your account, you will need to create a new account in order to contact Skype Customer Service.
Here is a link to the instruction on how to contact Skype Customer Service via their secure portal: Contact Customer Service
You will need to proceed through each step, one at a time. Sign on to the Skype website as requested. Choose the subject and topic which most closely matches the item you need assistance with. Then, continue past Step 2 of the instruction where several articles from the FAQ library will appear for you to review, and proceed to Step 3, Continue Support Request (the blue "button" appears at the lower right corner of the website page). You may also skip through Step 4 where you will be referred back here to the Community; no need to do this as the Community is where you started. When you complete the webform and click Submit, your information is relayed to Skype and you will receive a reply via e-mail.
If you are a Skype Premium or other eligible customer, you will be routed to start an instant message chat session with a Customer Service agent.
Regards,
Elaine
Was your question answered? Please click on the Accept as a Solution link so everyone can quickly find what works! Like a post or want to say, "Thank You" - ?? Click on the Kudos button!
Trustworthy information: Brian Krebs: 3 Basic Rules for Online Safety and Consumer Reports: Guide to Internet Security Online Safety Tip: Change your passwords often!

RE: iPhone 5 is showing wrong carrier name

My iPhone 5 is showing wrong carrier name (near signal bars and also in the settings) even after turning off multiple times and even after changing carrier settings from automatic to manual and Vice Versa. My device is on iOS 7.0.4. I've tried replacing the simcard but still it is showing wrong carrier name. My service provider told me that I'm using the correct signals. I've purchased this device whilst I was in the UK with Vodafone as the carrier but the device has been unlocked to network. I've now moved to India and I'm using AIRTEL but the carrier name is displayed as VODAFONE IN.

I've moved from Hyderabad to Bangalore and my phone started to show the correct carrier name, as soon as I entered to Karnataka cirlce from A.P. circle(I was on roaming). I think it's Airtel that relays the name as such in Hyd(A.P.) and it's nothing to do with the device. So, my problem is solved.
Hope this helps.

LR 5.3 showing wrong thumbnails

I have been running LR 5.3 smoothly for a while but a couple of minutes ago LR started to show wrong thumbnails, it shows thumbnails from a delete Snapshot. I have tried purging my cache but nothing happens. I have upgraded from LR 3 to LR 3.5 Ideas ? This is my system:
Lightroom version: 5.3 [938183]
Operating system: Windows 7 Home Premium Edition
Version: 6.1 [7601]
Application architecture: x64
System architecture: x64
Logical processor count: 2
Processor speed: 1.9 GHz
Built-in memory: 3003.1 MB
Real memory available to Lightroom: 3003.1 MB
Real memory used by Lightroom: 912.9 MB (30.4%)
Virtual memory used by Lightroom: 901.7 MB
Memory cache size: 364.0 MB
Maximum thread count used by Camera Raw: 2
System DPI setting: 96 DPI
Desktop composition enabled: Yes
Displays: 1) 1366x768
Application folder: C:\Program Files\Adobe\Adobe Photoshop Lightroom 5.3
Library Path: C:\Users\User\Pictures\Lightroom\Lightroom 5 Catalog.lrcat
Settings Folder: C:\Users\User\AppData\Roaming\Adobe\Lightroom
Installed Plugins:
1) 500px
2) Behance
3) Canon Tether Plugin
4) Facebook
5) Flickr
6) Leica Tether Plugin
7) Nikon Tether Plugin
8) SmugMug
Config.lua flags: None
Adapter #1: Vendor : 8086
    Device : 2a42
    Subsystem : 360b103c
    Revision : 7
    Video Memory : 64
AudioDeviceIOBlockSize: 1024
AudioDeviceName: Speakers (Conexant High Definition SmartAudio 221)
AudioDeviceNumberOfChannels: 2
AudioDeviceSampleRate: 44100
Build: LR5x89
CardID: 10818
Direct2DEnabled: false
GPUDevice: D3D
MaxTexture2DSize: 8192
OGLEnabled: true
Renderer: Mobile Intel(R) 4 Series Express Chipset Family
ShaderModel: 10.0
Vendor: Intel
VendorID: 32902
Version: 8086:2a42:360b103c:0007

I have had this problem also ever since I updated to 5.3, I think it is a major bug!
At random the preview window on the left doesnt show the preview of the presets anymore when I hover them, and when I click back and forth to other images it suddenly starts working again, its a very annoying problem and I cannot believe that Adobe isnt aware of it yet!
Marcel

"Invoice History Report "show wrong balance for supplier invoice with USD

Invoice History Report show wrong balance for supplier invoice with USD Currency
After I run this report i see in the last of this report there is difference between the supplier total
USD (Currency ) and the open Balance USD , it is decreased the open balance
for supplier with 2300 USD with out any reasons
bellow is some data copy of the report
======================================================
Supplier Site Total: SAR 34,700.00
Supplier Site Total: USD 39,000.00
Supplier Total: SAR 34,700.00
Supplier Total: USD 39,000.00
Open Balance: SAR 34,700.00
Open Balance: USD 36,700.00
*** End of Report ***
==============================================
please advise me from where can this differenc ( 39000 - 36,700=2300 )COMMING
or it is bug in this report , becuase i compare this report with other report in account payable like
-supplier open balance letter
-invoice register report
-invoice aging report
all this report give me the amount for supplier USD =39000
BUT AGIN FROM WHERE THE SYSTEM DECREASED THE AMOUNT TO 36,700
thanks

Can you try running Create Accounting For payments just before you run the Invoice History Report and re-check .
Thanks

Iphone 4 showing wrong IP address for home wireless

2 days ago we reset our home wireless password and updated our devices (ipad, laptop, and two cell phones). Now my iphone 4 will no longer connet to the wireless. It accepts the new password to join the network but it never connects. It is showing wrong IP address. How can I change it to the correct IP ? Tried hard rest, forget network, and renew lease all trying to get it to automatically update the info. Out of ideas. Any suggestions?

I have the exact same router as you, I have Comcast, and I am having the exact same INFURIATING problem.
Comcast and Apple have no ideas. Linksys tells me I am having a router problem.
I even went so far as to buy a new router and modem from Linksys (as they claim they no longer make the router/modem combo because it doesn't work well). I still don't buy this... my PC, my PS3, my DS... all of them connect to the router perfectly.
I have the new modem and router here and planned to give that a whirl tonight but Comcast was being difficult and saying it could take 72 hours to activate my new modem. Totally unsat. I had them reconnect the WCG200 and I am still trouble shooting to no avail...
If anyone finds a fix (short of a new router and new modem)... please post!

HT5622 I wrongly entered my apple id into my new i phone . It was my e mail address with a letter wrong I have registered right on the i cloud account but when I go to get apps it still shows wrong e mail How do I delete this incorrect e mail Thanks Mike

I wrongly entered my apple id into my new i phone . It was my e mail address with a letter wrong
I have registered correctly on the i cloud account but when I go to get apps it still shows wrong e mail
How do I delete this incorrect e mail? Thanks Mike

settings - app/itunes store - sign out - sign back in.

After my iphone4S update to 7.0.6, it have a problem that keep searching network then no service show on display. Can't call. I have try check sim card, reset network settings, and restore my iphone. Still not working at all. Need help please.

After my iphone4S update to 7.0.6, it have a problem that keep searching network then no service show on display. Can't call. I have try check sim card, reset network settings, and restore my iphone. Still not working at all. Need help please.Urgent.TQ

Izit software or hardware? Confuse:(
Only can use wifi now.
Any way thanks guys for ur suggestion:) amishcake and simes

FBL5N t code and BSEG table is showing wrong contract number

Hi,
The proces flow is contract number>sales order>DMR-->Invoice
Now when I am checking the VBFA table it's showing correct contract number against invoices but FBL5N t code and BSEG table are showing wrong contract numbers.
Why FBL5N and BSEG table is showing wrong contract number?
Currently we are using one enhancement and user exit is used to incorporate one customized field as identifier for bill type.
1. During the billing document release to accounting VFX3, The user exit triggering and it is update the customized fields and Net settlement indicator.
2. Using the Invoice number, get the fields VGBEL(Document number of the reference document) and VGPOS (Item number of the reference item) from VBRP and read table VBAP with VBELN and POSNR, to get DMR number (Sales Document) that created for the Invoice.
3. Use fields VGBEL and VGPOS on table VBAP to get the sale order number.
4. By using the Sales order number, get the Distribution channel to update Net indicator field
In accounting table BSEG-UZAWE = JF must be updated on the customer line.
5. Retrieve the sale order number and item level to get customized field from table VBAP
Any pointers.
Thanks
Ashu

Hi Reazuddin,
Thanks for your reply,
I am concercerned about BSEG table and using user exit EXIT_SAPLV60B_008 to post the document in FI.
Now in we have enhanced this user exit for contracts and included in this way.
SELECT SINGLE ZZ_CONTRACT FROM VBAK INTO (LC_CONTRACT) WHERE VBELN EQ cvbrp-vgbel.
Endloop.
*Moving the values to final accounting table
loop at xaccit.
xaccit-vertn = lc_contract.
xaccit-VBEL2 = xaccit-AUBEL.
xaccit-xref3 = lc_vbel2.
MODIFY xaccit .
ENDLOOP.
Clear: lc_contract,lc_vgbel,lc_vgpos,lc_vbel2.
But I am getting correct data when checked other clients( development and quality), this problem I am getting in production.
Do I need to ask the ABAP'er to debug this enhancement in production?
Thanks
Ashutosh

Location services shows wrong location

Similar Messages

Maybe you are looking for