Logic board and power supply symptoms on a Mid 2007 I Mac Intel

does anyone know what would cause my Mid 2007 Imac to quit abruply? On tun on the super drive spins up for about 5 sec and then spins down. No display No Nothing!! It was working fine up to this point. Could it be the power supply or logic board?? What other componants are in there that would cause this problem.
It is my daughter- in- law's Mac and they don't have alot of money to fix it so if I could fix it that would help.
THX for Ur Time!!

Unfortunately no one hear can truly diagnose the problem.
1. Run the Apple Extended Hardware Test using the original Install DVD 1 that came with that iMac.
Intel-based Macs: Using Apple Hardware Test
2. Call your local Authorized Apple Service Provider and have them test it.
How to find your nearest Apple Authorized Service Provider (AASP) or Apple Authorized Distributor (AAD)

Similar Messages

  • 6-month old Mac Pro has already had a new logic board and power supply

    At a cost of $400 in shipping and a one-month wait, my 5-month old Mac Pro got a new power supply and logic board
    Now I keep getting kernel panics, runaway kernel_task in Activity Monitor, and corrupted boot drives
    External Firewire drives work some of the time, and occasionally my USB devices dont work either
    This computer is a nightmare - how do I begin to figure out if this is OS (10.6.4) or hardware related?
    The extended AHT test reports that all is OK - as does an extended memory test using Applejack
    Should I do firmware updates and re-install the 10.6.4 combo pack, or am I just wasting more of my time?
    I've got 4 macs and this is the only one that works badly - I think Apple's OS updates are getting as bad as Windows updates

    My first question is why you spent $400 to get a 5 month old system fixed. That should have been covered under the warranty. So someone ripped you off, or you left out some key details.
    And if you had both the logic board and PSU replaced, did you ever stop to think that maybe the problem lies with the power coming into your house? It's not really the big power spikes or blackouts you need to worry about, since those are pretty rare. What you need to worry about are the small fluctuations in voltage that happen several hundred times a day, if not an hour. Sometimes there's not quite enough power, other times there's a little too much, and all of this takes a steady toll on the PSU. It will do what it can to try and feed the rest of the computer a steady diet of electricity, but sometimes a jolt will get past it and start damaging other components. It could even cause data corruption on your HDD.
    If the PSU and logic board already went, who knows what damage it may have caused to anything else. It may just be taking longer to show up.
    It might also be that whomever ripped you off to the tune of $400 simply traded you one defective logic board for another. Or maybe they don't really know how to protect against ESD. I once saw a repair shop where the techs smoked in the same room they did the repairs. Sadly, for every one good tech out there, there's probably at least 3 complete idiots. Kind of like auto mechanics.
    And I never have problems with Windows or Apple updates. Seems like on Windows the majority of people who have problems with updates are either running some program designed to change the way Windows looks or messes with low level system files, or they have a malware infestation they were unaware of/oblivious to. Most of the people who have problems with Apple updates seem to be the same way. They're running some truly bizarre programs that mess with the system in ways programs were not intended to mess with the system. There's generally a reason OS vendors provide an API for developers. You deviate from that at your own peril.

  • I replaced the logic board and power supply in my iMac and it's still dead.

    Recently lighting hit my friend's house and his iMac was plugged into an outlet. It did frie the power supply. I replaced it and the logic board. The first two LEDS on the logic board light up green so I know it's getting power. However it still wont boot. A white light flashes in the bottom right corner and the fan kicks on and then off. I've tried reseting the PRAM and SMC and now it wont do anything at all?

    The strike could have written everything off in the computer or if the part still works it still could be damaged and cause hard to identify problems or fail within a short time.
    rkaufmans advice holds true, either take in it for service or probably write it off on the insurance. It is quite likely it is beyond economic repair.
    If the strike was close by, sometimes not too much gets damaged but a direct strike, the ones I have seen have wrote the machines off.
    Also do you know the provinence of the replacement parts, have you seen them working and know they are good and a direct replacement?

  • TS1367 Hi....I have an Intel based iMac.......serial # QP******DAS....I need a new logic board and power supply please ......can anyone help..........thank you

    Hi I have an intel based Imac......serial #      QP******DAS.....early 2011 I beleive......I have been advised that I need to replace both the logicboard and the power supply as the mac fails to start.
    I have been quoted a ridiculous amount of maoney for them and wanted to buy direct in the USA in the near future......does anybody sell thes plaeas........thanx ...Mike
    <Edited By Host>

    Check the following places: 
    We Love Macs! 
    iFixit.com 
    Also do a Google search. 

  • Where can I buy an inverter board and cable for my iMac 24 (mid 2007)

    Where can I buy an inverter board and cable for my iMac 24 (mid 2007)

    See clues here in the last post...
    http://forums.macrumors.com/archive/index.php/t-869303.html
    Laughably expensive, but part#s may help searching...
    http://www.welovemacs.com/im24lcdresc.html
    iMac 24" LCD Panel w/ Inverter Board and Gasket (p/n 1001349)
    24" iMac LCD Panel w/ Inverter Board and Gasket (p/n 1005316)
    24" iMac LCD Display Panel (p/n 1004596)

  • IMac G5 won't start up - logic board or power supply?

    My oldest son killed my iMac G5. Apparently he'd taken to sneaking downstairs in the middle of the night and watching videos on YouTube. One night, during his viewing session, the iMac threw up a kernel panic and the fan came on. My son tried to turn off the iMac but couldn't find the switch. So *he went to bed and left the iMac with the fan on full-blast.* When I came downstairs to go to work, 6 hours later, I turned off the machine, waited for a minute or so, and then attempted to turn it on.
    The iMac is stone dead. Will not turn on.
    I'm deathly afraid the logic board is cooked. Those things are damned expensive. I held off on doing anything for a while, but then I was talking offhand with a Genius at a local Apple store. He said it might be as simple as a power supply. Which would be great - $125 is a lot cheaper than $800, and I could do this repair myself. But I don't want to sink $125 into the machine unless I have a pretty good idea that this will, in fact, fix it.
    Anyone else had this problem? Did it turn out to be the logic board, or the power supply, or something else entirely?

    First off, the kid is grounded - second, which model do you have? Have you tried resetting the SMU? Resetting the SMU can resolve some computer issues such as not starting up, not displaying video, sleep issues, fan noise issues, and so on. If your computer still exhibits these types of issues even after you've restarted the computer, try resetting the SMU. To reset the SMU on one of these iMacs:
    1. Turn off the computer by choosing Shut Down from the Apple menu, or by holding the power button until the computer turns off.
    2. Unplug all cables from the computer, including the power cord.
    3. Wait 10 seconds.
    4. Plug in the power cord while simultaneously pressing and holding the power button on the back of the computer.
    5. Let go of the power button.
    6. Press the power button once more to start up your iMac.
    Let us know if this helps,

  • IMac G5 (2004) logic board and the repair extension program

    Hi,
    I know that there are tons of topics about logic board/power supply troubles witht the first generation G5s, and I'm sorry to start yet another new thread, but I still have some questions about this issue.
    I have a first generation iMac G5. Long story short...when I first got it the computer would shut itself off sometimes after I had put it to sleep. When I would try to restart nothing would happen, but usually letting it sit unplugged a while would solve the problem (occasionally when I'd restart a different start up noise would sound and the white light would flash quickly). It happened so randomly, that I just lived with it, blaming the problem on my dorm network, or a power failure. A few days ago I tried to start the computer up and nothing happened (just a VERY faint sound like a clicking or ticking or intermitant humming...definatly electrical sounding). I unplugged it overnight, but the next day still nothing. I decided to go through the troubleshooting steps Apple lists online. The internal power button could not start it up and the second LED does not flash, which according to Apple means the logic board needs replacing. Luckily my serial # is covered by the Repair Extension Program, and I'm bringing my computer in tomorrow morning to be fixed (just in time for back to school).
    I have become concerned, while browsing the discussion topics, that this fix may not be permenant. I've read a few posts that claim that they are on their third Logic Boards, and this kind of scares me. My parents bought me the computer (our family's first ever Mac) and did not purchase the AppleCare extended warranty (they had heard how reliable Macs were...hmmm.) I didn't even know that I could purchase AppleCare after-the-fact until it was several months after my 1yr warranty expired. I do appreciate the fact that Apple recognized what seems to be a common problem with this generation of iMacs, but I wonder why they did not contact the owners of these machines to let them know that the problem and repair extension even existed.
    So I guess my real question is...Does anyone know if, after this repair Apple will replace the logic board if it dies again? Is there a limit to the number of qualified repairs you can get through this Repair Extension program? Also is there any other Extended warranty type thing I can purchase after my 1yr. warranty is up.
    Sorry the post is so long...I'm just scared about the fate of my beloved Mac.
    iMac G5 (2004)   Mac OS X (10.3.9)  

    Oh man, am I actually relieved reading this thread. Just took my baby (iMac G5 first generation) in for repairs today, not knowing what was wrong with it. Luckily my serial numbers are in the range, so I'm crossing my fingers that they're going to cover this.
    Brief synopsis of what happened, in case it differs from anyone else's
    About a month ago, my iMac started to not wake up from sleep mode. Instead of waking up, it would just shut itself off. This continued for about 2 months, with me thinking nothing of it. Then, instead of shutting itself off, the computer would restart when I attempted to put it to sleep.
    Then, last night, I was surfing the net and all of a sudden the power just failed. No noise, no "grey screen", we're talking like a millisecond later the screen was black. I treid unplugging the machine and then plugging it back in while simultaneously holding the power button to reset the PSU and still nothing. At that point it was about 1:30 in the morning, so I just went to bed not wanting to deal with it until the next day. By the time I woke up, there was a distinct smell of electrical components burning (in grade 8 shop class we used to hook up resistors to the voltage generator and crank the juice up until they fried when teach wasn't around, so I distinctly remembered the acrid stench :P)
    I opened the back up and did the LED check, and #2 wouldn't even blink. So I took it in and they said they'd have to get back to me and that's where I stand now.
    The thing that concerns me is that if some of the components fried that there may be possible damage to the motherboard etc. Luckily I'm not too worried about the hard drive because it did still boot up and all. People that have experience with this, what usually happens with files on your HD after a logic board replacement? Are they usually fine?
    The other thing that concerns me is that apple has made no effort to contact me, and it will be 2 years after the purchasing date come November 1, 2006. I'm lucky that I caught this now before it was too late.

  • Upgrade video card and power supply or upgrade my pc?

    I have a :
    HP
    Series Pavilion Model M8530F(KT334AA) Type Media Center / HTPC Processor AMD Phenom X4 9550(2.2GHz) Processor Main Features 64 bit Quad-Core Processor Cache Per Processor 4 x 512KB L2 Cache Memory 5GB DDR2 800 Hard Drive 750GB 7200RPM SATA Optical Drive 1 SuperMulti DVD Burner with LightScribe Technology Graphics NVIDIA GeForce 9300GE with Hybrid SLI Technology with 256MB dedicated video memory, DVI and HDMI capabilities, and support for Microsoft DirectX 10. Up to 1919MB Total Available Graphics Memory as allocated by Windows Vista Audio High Definition audio Ethernet Integrated 10/100/1000Mbps network interface Keyboard HP multimedia keyboard Mouse HP optical mouse Operating System Windows Vista Home Premium 64-bit Software Included Photo and Video
    muvee autoProducer Basic: Automatically create professional looking home videos and burn to DVD
    Entertainment
    Cyberlink DVD Suite Deluxe: Automatically fix and edit videos and create CDs and DVDs. Edit, burn and archive data to discs.
    Productivity
    Microsoft Works 9: Includes a word processor, spreadsheet, database and calendar
    Microsoft Office Home and Student Edition 2007 Trial: 60-day trial version
    Adobe Reader 8: Read and print PDF file
    PC Security
    Norton Internet Security 2008: Protect your PC out of the box (60 days of complimentary live updates)
    Online Services
    Easy sign-up to major dial-up and broadband Internet Service Providers:
    - MSN dial-up (offer included)
    - NetZero Dial-Up (offer included)
    - NetZero Accelerated Dial-Up (offer included)
    - Juno Turbo Dial-Up (offer included)
    - High Speed Internet Services Comparison Shopping
    Motherboard Chipset NVIDIA GeForce 8200 Chipset
    CPU CPU Type Phenom X4 Installed Qty 1 CPU Speed 9550(2.2GHz) L2 Cache Per CPU 4 x 512KB CPU Socket Type AM2+ CPU Main Features 64 bit Quad-Core Processor
    Graphics GPU/VPU Type NVIDIA GeForce 9300 GE Graphics Interface PCI Express x16
    Memory Memory Capacity 5GB DDR2 Memory Speed DDR2 800 Form Factor DIMM 240-pin Memory Spec 2GB x 1 & 1GB x 3 Memory Slots (Available/Total) 0/4 Maximum Memory Supported 8GB
    Hard Drive HDD Capacity 750GB HDD Interface SATA HDD RPM 7200rpm
    Optical Drive Optical Drive Type DVD Super Multi Optical Drive Spec SuperMulti DVD Burner with LightScribe Technology
    16x DVD±R, 8x DVD+RW, 6x DVD-RW, 8x DVD+R DL, 4x DVD-R DL, 5x DVD-RAM, 16x DVD-ROM, 40x CDR, 32x CDRW, 40x CD-ROM
    Audio Audio Chipset Integrated
    Communications Modem 56K LAN Chipset Integrated LAN Speed 10/100/1000Mbps
    Front Panel Ports Front USB 2 Front IEEE 1394 1 Front Audio Ports 2 Card Reader Front panel 15-in-1 memory card reader: supports SmartMedia, xD, MultiMedia Card, Secure Digital (SD), Mini Secure Digital, Compact Flash I, Compact Flash II, IBM Microdrive, Memory Stick, Memory Stick Pro, Memory Stick Duo, Memory Stick Pro Duo, RSMMC, MMC Mobile, MMC+
    Back Panel Ports PS/2 2 Video Ports 1 DVI, 1 HDMI Rear USB 4 Rear IEEE 1394 1 RJ45 1 port Rear Audio Ports 6 ports S/P DIF 1 port
    Expansion PCI Slots (Available/Total) (2/3) PCI-E x1 slots
    (0/1) PCI-E x16 slot
    Mouse Mouse Type HP optical mouse
    Keyboard Keyboard Type HP multimedia keyboard
    Physical Spec Dimensions 16.54" x 15.16" x 7.60" Weight 32.00 lbs.
    Manufacturer Warranty Parts 1 year limited Labor 1 year limited
    Sorry for the long copy and paste. I read that I can upgrade the video card and power supply. But atm when I play world of warcraft at ultra settings, I tend to lag really bad in the new instances with the new cat expansion that came out. I wanted to know if I should upgrade the video card and power supply for better performance or just upgrade my whole pc tower.  Fyi, I am running a Acer X243w lcd flat panel monitor if that helps too.

    My brother has a high end laptop with a built in, high end gaming video card (I forget which one). He's able to run the game on full-on Ultra. 
    I have an integrated video card which games the game on.. 'cartoon'.. mode. It's lower then low. When someone shoots a powerful spell at me, I go into a DOS Prompt. (not really, but it's pretty bad).
    Funny thing is, I can still kick my brother's butt in any PVP match he wants to set up. 
    But I guess his graphics are pretty....
    As for which video card works best, I'd have to do some research. After that graphics update they did with CAT,  it's kind of a toss up again.
    I am a Bestbuy employee who volunteers on these boards on my own time. I am not paid for posting here, and you should understand that my opinions are exactly that - opinions. I do not represent Bestbuy in any way.
    : Open Mailbox

  • New logic board, and new display, but now completely dead.

    Hi guys,
    I've got an iBook G3, running 10.3.9.
    In December 2006, the logic board failed, so I bought a MacBook, because I didn't have time to be offline waiting weeks for Apple to replace the iBook's logic board.
    After much badgering, Apple reluctantly replaced the iBook's logic board under the extended warranty program.
    While the iBook was with the Apple repair store, they replaced the display for new as well, even though I didn't ask them to, and even though I wasn't charged for it.
    I presume that was because the store discovered that the display was duff enough to be replaced under another extended warranty program.
    When I got the "repaired" unit home, with a brand new logic board, and a brand new display, I turned it on, and it seemed to be working fine, so I turned it off, and continued to use my MacBook.
    A few weeks ago, the second logic board on my MacBook failed (another long horror story entirely), so I began using the iBook for the first time since it had been "repaired" some six months earlier.
    Almost immediately, the iBook began exhibiting a major problem, specifically that I'd be typing away, and suddenly the display would go black.
    I could just about see the icons and documents on the screen, but the unit was unusable.
    So I pulled restarts, full shutdowns, disk utility, zapped the PRAM, etc, all to no avail.
    It seemed to be an intermittent problem.
    For example, sometimes, from a cold start, the unit would work for two or three hours until the display went black.
    Other times, I'd pull a cold start, and it would go straight to the black display.
    By chance, I discovered that if I gave the iBook a shake, the display would come back on.
    But then it would go black after a second or two.
    And then with another shake, it would come back on for a second or two.
    And then it would go black after a second or two.
    And then with another shake, it would come back on, sometimes for a couple of hours at a time.
    So I figured that it must be a cable which, during the installation of the logic board, and/or the new display, wasn't seated correctly by the technician.
    I phoned Apple, and told them about it.
    They said that because I had reported the issue beyond 90 days since the logic board had been replaced, it was no longer Apple's problem.
    I explained to Apple that I hadn't used the iBook for six months, because I had a MacBook.
    After much badgering, Apple has agreed to replace the logic board if it's faulty.
    However, Apple has refused to replace the NEW display, even if that's also faulty.
    Apple is also insisting that I have to pay all the labor charges.
    Meanwhile, I've noticed that the iBook is now incredibly hot.
    I mean, the MacBook is infamous for running hot, but this "repaired" iBook makes my MacBook feel like a block of ice by comparison.
    I don't remember the iBook running so extremely hot before the "repair."
    Which has made me notice that during the last few weeks, I've never heard the iBook's fan come on.
    I presume that an iBook has a fan ?
    Please confirm.
    Therefore, another loose cable ?
    Today, the display went black again, as usual.
    So I gave the iBook a shake.
    But this time, nothing happened.
    No display.
    No fan.
    No hard drive spinning.
    Just silent and dead.
    What do you reckon, guys ?
    Duff logic board ?
    And/or duff display ?
    And/or duff fan ?
    And/or duff cabling by the technician ?
    As far as I'm concerned, I don't see why I should have to pay for yet another repair, to correct hardware and/or workmanship which was so bad that after only three weeks of ACTUAL use since the "repair", the unit is now completely dead.
    All opinions and advice gratefully received.
    With thanks and best wishes,
    Michael
    London, England

    Hi S,
    Many thanks for your helpful and swift response.
    I agree with you regarding the likelihood that these problems would have surfaced immediately during normal usage, regardless of how much or little time had passed since the repair.
    As advised, I will inform Apple Customer Relations UK about the new developments.
    Indeed, when I resubmit the iBook, I'll include a print-out of this discussion.
    I agree with you about the fan.
    Prior to the failure of the first logic board, I ran that iBook for YEARS, without noticing any heat issue.
    Indeed, if there had been such incredible heat, then I'd have searched these discussion boards, and reported it to Apple HQ.
    Therefore, the astonishing heat is definitely a new development since the "repair."
    Consequently, I take on board your comments about the lack of a working fan since the "repair", which I shall also mention to Apple HQ.
    As for running the Apple Hardware Test, the unit is completely dead.
    The power cable is green, but the unit is now completely silent and black.
    I also note your suggestions regarding the cable which connects the display to the rest of the unit, which I shall also mention to Apple HQ.
    No repair sheet was ever given to me by the Apple Repair Centre (ARC).
    Indeed, no receipt was ever given to me when I delivered the unit to the ARC, nor was any paperwork ever given to me when I collected the unit from the ARC.
    However, Apple HQ can see on their screen that the logic board and display were both replaced for new by the ARC.
    What else was and wasn't done by the ARC is a mystery.
    I'll phone the ARC and ask for copies of any and all paperwork, so that I can submit it all to Apple HQ, which I note is your recommended option, rather than returning the unit to the ARC.
    However, the complicating factor is that with the exception of the logic board, it is my understanding that Apple is denying any liability on any part of the "repaired" unit, including the brand new display.
    If I understand Apple HQ correctly, they're now saying that all other hardware and labor costs will be mine.
    I'm sure I could buy a WORKING second-hand iBook G3 for the same price as a repair, if not cheaper.
    Therefore, perhaps I should return the unit to the ARC, and give them the opportunity to correct their previous workmanship, at their OWN cost.
    Because as far as I'm concerned, the ARC had two customers during the repair: Apple and the end-user, as evidenced by the fact that the ARC has invoiced its first customer Apple for workmanship which was clearly not up to Apple's own standards, and the ARC has then delivered the unit to its second customer, the end-user.
    In addition, regardless of Apple's 90 day warranty on repaired hardware, UK law includes the Sale of Goods Act 1979, and other relevant legislation: http://www.dti.gov.uk/consumers/fact-sheets/page38311.html
    Furthermore, if the ARC is completely unhelpful, I could jump all over them, by writing to Apple HQ, with cc's to the UK editions of MacWorld, MacFormat, and MacUser magazines.
    As advised, if the unit goes to Apple HQ, I will suggest that the unit is looked at carefully during disassembly, to see if errors were made during the ARC "repair."
    I'm always polite when on the phone to Apple, because I love the company so much.
    Indeed, even though during the last twelve months, I've been having very bad luck with the iBook, as well as with a MacBook which has exhibited so many problems that Apple has now agreed to replace old for new, I still love my Mac.
    And joy, sweet joy, I've just seen on the TNT courier's tracker website, that my replacement MacBook, built by Apple in Singapore, then flown to Arnhem in Germany, then flown to Northampton UK, then delivered to Heathrow UK, left the Heathrow depot 30 minutes ago, for delivery to the customer.
    And the sun is shining.
    Thank you again for all your kind and wise advice.
    With best wishes,
    Michael
    London, England

  • Logic Board and Hard drive

    I have a 20" 1.25GHZ G4 iMac that had a hard drive failure. It could be seen by Disk Warrior, Drive Genius but wouldn't respond to repairs. After taking it out I was able to confirm that it's bad.
    I installed a new drive but that can't be seen by install discs(original and 10.5) or DW and DG. I replaced the cable to the logic board and confirmed continuity on the power wire to the drive. (And the DVD drive runs so it has power). I tried jumper settings of "cable Select" and "master". I confirmed off line that the new drive is good. New board battery. Reset PMU.
    Does it make any sense that the problem is the logic board? Everything else seems okay - display, DVD drive, etc. What confuses me about the logic board is that it worked enough to see the bad drive. Anything else to check/change?

    Depending on the brand of replacement hard disk drive,
    and the requirements with whichever one you have to
    work in the iMac G4 configuration, the jumper pin setting
    may be the issue. There could also be an issue with an
    ATA controller on the logicboard; or other hardware...
    Given the possibility of issues in this, some users have
    opted to stay away from some brands of drives which
    had presented a problem if used as replacement drives
    in these computers. Some leave a lasting impression.
    {One example, is WD drives. They may be fine, but I
    don't prefer to use them in Macs ... from SCSI days!}
    Good luck & happy computing!

  • Mid 2009 applecare logic board and battery ADVICE

    returning mac OS and mac hardware buyer here.
    i have been questioning (read complaining) about the battery life (1 1/2 hours on safari) and the performance (spinning beachballs on startup, on wake and on starting safari among other things) since i bought this machine. i brought it in for the umpteenth time to the genius bar (they apparently only have 3 of these on record?!) because i had a break and i have a "service battery" alert.
    i am being told i can replace the battery and the logic board based upon their diagnostics of the machine and i have FINALLY (Whoo-HOOO yippeee kayeeee'y!!) got a committment from a mac rep that i should be expecting  3 1/2 - 4 hours out of the battery and not 1 1/2 hours.
    i don't really have an option here from everything i can tell but does anyone have any advice for me on this? warranty is up in February and from what i am being told i can bring it back if i bring it home and still only get poor battery life.
    at the same time i am really unhappy (insert expletive) about having spent so much time troubleshooting this machine only to be told that the hardware seems fine or that the battery tests normal or whatever. this macbook pro 13 inch seems like it was a dog since the day i bought it.
    my preference would REALLYT be to trade into mac on a new macbook pro 15" and i am wondering if i am instead i am going to have to just repair this machine (thank my lucky stars that i buy applecare) and empirically test the machine on my end to make sure that i am getting more than 2 hours per charge and that i don't have the spinning beachballs that i have had to have dealt with over the last 3 years...
    i mean, i /have/ to fix this machine and monitor it over the next three months instead of them helping me cut bait with it by getting some financial incentive somehow to move into a new MBP is that right...?
    TIA

    thanks.
    looks like it has now had a new battery and a new logic board and it is still failing hardware test for the battery.
    they are now sending it out for additional testing to some other facility.
    anyone had a similar experience?

  • Having logic board and inverter replaced - will post results.

    My MBP is afflicted with the CPU whine and the LCD whine, not to mention the "Moo". I solved the Airport not connecting automatically issue on my own.
    Talked to Apple about the whines, they wanted me to take it to the local guys, which I was happy to do. I dropped it off this morning, going to pick it up after work.
    They are ordering me a replacement logic board, and the inverter (at my request). I will keep my MBP until they come in and then they will swap the new parts in.
    I'm guessing it won't be a short wait for the parts, but I will follow up in this thread detailing further results and noise levels.
    Personally, I am very impressed with the local service response. They agreed to get the inverter at my request even after opening it up and finding the noise to all eb coming from the logic board.
    I know it ***** to wait... but there is more to come. Any questions about my specific machine, etc; post and I will answer.

    BrenM - Good luck with your MBP! I hope the replacement logic board and inverter resolve the issues.
    As for me, my MBP has been at an Apple Authorized Service Provider in Oakville, Ontario for about a week and a half. They first ordered a replacement logic board, which came from California ... took 2 or 3 days. Unfortunately the replacement logic board did not resolve the high-pitched "whine" issue. The tech told me it is quieter, but not gone .... So on Monday he advised me that they are replacing the inverter, which is on order. They expect to receive it on Wednesday. To be honest, I don't think the inverter will address the high-pitched "whine", as I've been following this issue on here very closely. But it probably will resolve the buzz from the screen when adjusting the brightness, so that's good.
    The ASP that I took my MBP to in Oakville has been great. They're really on the ball with it and I know they are doing the best they can. But what it really comes down to is ... if Apple doesn't have an issue to this high-pitched "whine", there's not much the ASP can do. I appreciate them replacing the logic board and inverter, but it's really Apple that needs to get their act in gear and resolve this once and for all. The MBP's have been out for what ... 5-6 weeks now? This has been a hot topic ever since people starting receiving their MBP's, and Apple needs to face the fact that people are not going to let this go until a solution is provided.
    The ASP told me that if after replacing the inverter it is still not resolved, I'll need to put up with it until Apple resolves the issue, as there's nothing else they can do. I asked him - what if it takes Apple 2-3 months to resolve the issue? He said I can bring it right back in to have it fixed. So that's good.
    The other thing I was considering is when I get my MBP back, to contact Customer Relations and put up a fuss to receive a replacement. But ... then the replacement will probably have the high-pitched "whine". I don't know what to do at this point. It sort of bothers me that my $3000 MBP is no longer pristine, as it has been serviced and received replacement parts ... what do you guys think? Should i be firm with customer relations and (politely) demand a repacement?

  • 2x iMac G5: Both Logic Board and Display Problems, Warrenty?

    Hello,
    Thank you for looking at this topic.
    I am Jeroen from The Netherlands and proud owner of several Mac Mini's, iMac's and Macbook's. I have 2times the iMac G5, a beautiful machine, but both not working since 2 months.
    I have two times the iMac G5 with iSight, both have logic board and display problems.
    The first iMac doenst start at all, black screen, i hear the chime, but nothing happening. After a minute i see one horizantal white stripe but nothing happens.
    The second iMac has weird horizantal stripes also, but the computer starts. It gives a finder and questionmark icon. After a while the fans go crazy.
    Both these symptons are widely known on the internet. I would like to get this fixed, but prices are crazy. And because this is a common issue I would expect to get this fixed for no costs. I have contacted several Apple resellers but they shown me high prices and bad services. On these forums I've saw people in the USA who get this fixed free of charge.
    Does anyone has any advice for me? I'll call apple USA this morning.
    Thankyou for ur time.

    Welcome to Apple Discussions.
    I know of no repair extension authorization which provides for the repair of either computer you describe beyond its original 12 month period of coverage. If either machine is covered by a warranty extension program provided by AppleCare, then the parts, labor or both required to replace the defective components may be offered at no charge to you. Final determination of eligibility is made at the part level by authorized Apple service providers or dealers and by the specific serial number of the machine submitted for service.
    Absent a warranty extension, however, it is quite likely that you will have to pay for the repairs is you elect to have them performed.

  • The cable between the logic board and the 3G board  was removed can I convert it to a Wifi only?

    I have a Ipad 2 3g. someone detached the cable between the logic board and the 3G board can I convert it to a Wifi only?

    The ipads that have 3g have an extra section attached to the logic board by a glued on wire. I bought this at a tag sale. Someone was apparently trying to repair their iPad and they did not know that when you removed that glued strip attaching the 3g antenna to the logic board you would never be able to re-atach it again later. So basicaly my 3g logic board is now in two pieces. the main logic board with wifi and the cdma 3g antenna. Now their is no differnce between the logic boards in either wifi only or wifi and 3g devices. I attempted to restore the device with the ios for wifi only, because there are 3 different ios versions depending on if you have wifi only wifi 3g with SIM card, or wifi 3g cdma.

  • Will this video card and power supply work on my computer? HP Pavilion p6213w Desktop PC

    I have a HP Pavilion p6213w Desktop PC, will this video card and power supply work on my computer?
    Video Card: http://www.tigerdirect.com/applications/SearchTools/item-details.asp?EdpNo=8379339&sku=A455-0760
    Power Supply: http://www.tigerdirect.com/applications/SearchTools/item-details.asp?EdpNo=4668507&sku=C13-2511
    Any help is greatly appreciated, thanks.

    It is unlikely that the power supply will fit/work in your HP Pavilion p6213w Desktop Computer. Please consider the Corsiar CX500, CX500M, CX600, and CX600M for your power supply needs. These power supplies are the same physical size as the factory unit and are known to fit and work in most HP full-sized consumer desktop computers.
    There is a chance that the GTX 760 and other current generation video cards may not work in your computer. These newer cards typically require the computer to support the most current UEFI standards and many motherboards don't meet this criteria. Please know the return policy on any video card you purchase, in case it doesn't work. If the GTX 760 doesn't work, consider the GTX 650/660 Ti or equivalent AMD graphics card for your graphics card needs.
    If you have any further questions, please don't hesitate to ask.
    Please click the White KUDOS "Thumbs Up" to show your appreciation
    Frank
    {------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
    Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
    This is a user supported forum. I am a volunteer and I don't work for HP.
    HP 15t-j100 (on loan from HP)
    HP 13 Split x2 (on loan from HP)
    HP Slate8 Pro (on loan from HP)
    HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
    HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
    HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
    HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
    HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

Maybe you are looking for

  • Informatica's connect for SAP R/3

    Hi guru's I want to know what is informatica's connect for SAP R/3 ? I am an informatica developer and could not find any help regarding this in informatica's documentation. thanks your help is greatly apperciated. preeti

  • Links do not appear in links panel in inDesign CS4

    I don't recall when this happened but I no longer have any links in the Links Panel in inDesign CS4 in ANY of my documents old, new, it doesn't matter. If I package a file it gathers all the links if I need to update a link I have to go to the origin

  • Upgrade HFM 9.2.0.3 to 11.1.1.3

    Hello, I'm new to the subject hfm, like to know what are the benefits of carrying out an upgrade of HFM 9.2.0.3 to 11.1.1.3???, is recommended??? and why not upgrade of 9.2.0.3 to 11.1.2??? is much the change in architecture that makes it very diffic

  • Logical Standby - Application Express Recovery

    Ive asked a similar question in the following threads:- Re: Recovering Logical Standby - Non-Guarded Schemas Logical Standby - Application Express Recovery Were using 10g Logical Standby database for our reporting environment and within it we have Or

  • Revoking the access for a user based on the date specified by the certifier.

    Hi, Is it possible for the certifier to specify a date before he clicks on "Revoke" so that the user access is revoked on specified date in R2 PS2. Regards, Shiva