Long motor test error did not reach target speed in time. fan runs all the time. sensor is connected. do I have a bad fan? speed in time speed
ran apple hardware diagnostics. fan - master - long motor test error: did not reach target speed in time. fan runs all the time. sensor is connected. do I have a bad fan?
ran apple hardware diagnostics. fan - master - long motor test error: did not reach target speed in time. fan runs all the time. sensor is connected. do I have a bad fan?
Similar Messages
-
T61 fan runs all the time on AC, does not when on battery
Hello,
with the lastest BIOS (and those before) my T61's (8889) fan runs all the time when it is AC powered. (After initial start it begins with 0, then ~2500 rpm, then ~3100 rpm and then stays there even if idle).
When on battery under the same circumstances, it doesn't go above ~2500rpm (which is far less noisy then the ~3100rpm level) and often it even stops.
As far as the BIOS settings allow, it is trimmed to max. power saving also when AC powered but still it's getting on my nerves.
Can Lenovo please look into this and make it as quiet as it is on battery also when on AC?
P.S. I cannot see that the temperature levels as reported through ACPI are any higher on AC then on battery, so I don't understand why the fan has to run all the time that loud when on AC.
Thanks,
DanielHi Daniel,
There are two options for you to consider:
1) Better CPU speed management:
- Install a utility called "RMClock" to better manage the CPU (it's a free utility that throttles the CPU to run at different speeds depending on the needs - the CPU speeds increase automatically to full power when required).
- By regulating the CPU speed, the fan will not need to work that often to expell hot air, because the CPU generates much less heat.
- you will find a quick "how-to" for using RMClock --> HERE
2) BIOS thermal management
- You can change the BIOS settings for the "thermal management" (enter BIOS, choose "Config", then "Thermal Management" ) . Change the fan control from "performance" to "battery optimized" under the "plugged-in" option. This will reduce the frequency with which the fan runs, but beware that if your system is plugged in and you're not using any CPU management - meaning that your CPU is running at full speed, then the system will heat up more than you'll be comfortable with!!
I would therefore suggest that you use a CPU throttling management utility (like RMClock mentioned above) together with the thermal management option in your BIOS. This will reduce the frequency with which the fan starts and operates but still keeping the system cool.
A completely different approach is to install and use "Thinkpad Fan Control" -- read this thread ... Be aware that the utility takes a lot of tweaking to get the settings right, but also be aware that you can damage your system if you do not make the right settings!!!
Hope this helps!
Steve
Message Edited by icantux on 07-09-2008 02:18 PM -
I have an iMac (Mid 2007) upgraded to Lion OS. My fan runs at high speed all the time. I reset the SMT without results. I had no way to do the hardware test.
Can I fix this high fan speed?Open Activity Monitor in the Utilities folder. Select All Processes from the Processes dropdown menu. Click twice on the CPU% column header to display in descending order. If you find a process using a large amount of CPU time, then select the process and click on the Quit icon in the toolbar. Click on the Force Quit button to kill the process. See if that helps. Be sure to note the name of the runaway process so you can track down the cause of the problem.
If the above doesn't help then create a new user account. Log into the new account. Does this fix the problem? -
I cleared a conversation in my messages. I do not delete. How do I get all the messages back from this sender?
Clearing a conversation is the same as deleting the messages, so unfortunately they're gone. You could always restore from a previous backup, but you would lose anything that you've added/changed etc on your phone between the last time you synced your phone and now.
-
Fan runs all the time.. Apple Hardware Test Error
The fan on my 13" Macbook Pro recently started running continously. I tried resseting the SMC per directions on the apple support page, when that didnt work I ran the Apple Hardware Test from my install cd, and got the following error: 4SNS/1/4000000 : TNOD-128.000
I've googled everywhere, and can't find what that means!
Any ideas?Hi Alex FLB, welcome to Apple Discussions!
I had this exact error code (4SNS/1/4000000) on my iMac a couple months ago, along with the same symptoms. The code refers to one or more faulty temperature sensors on the logic board of the unit. Because the MBP isn't getting a reading from a temperature sensor, it has no idea what the actual temperature of the computer is, so it runs the fans at high speed in a fail-safe mode to prevent damage.
What this means is that you'll have to either take the machine to an Apple store or call Applecare over the phone to initiate a repair. Tell them the symptoms, and have them run the AHT or give them the code. If the machine is still under the one year warranty (or Applecare) then the logic board should be replaced free of charge for you. It's the only way to replace these temperature sensors, as they are incorporated into the board itself and cannot be separated from it.
If you Google "AHT 4SNS/1/4000000" then you may be able to find more information!
--Travis -
I have used Satmap online mapping for several years on a PC
Now moved to Mac and all was ok until i moved to Mavericks!!
I can no longer save *.GPX files to the Mac - it appears to do everything except actually saving the file
Any ideas before i have to buy another PC would be helpful
This is using Safari I have also tried Firefox all software is up to date
this is on my Imac and Macbook Pro both 2013I have used Satmap online mapping for several years on a PC
Now moved to Mac and all was ok until i moved to Mavericks!!
I can no longer save *.GPX files to the Mac - it appears to do everything except actually saving the file
Any ideas before i have to buy another PC would be helpful
This is using Safari I have also tried Firefox all software is up to date
this is on my Imac and Macbook Pro both 2013 -
I bought a mac companion for my desktop mac running os x but received the following error message when I tried to install the quikprotect software download: "power pc no longer supported." I did not read that anywhere when investigating. What gives?
PPC, also known as PowerPC has not existed on Macs since the beginning of 2006. Apple made a bridge software and included it with Mac OSes until 10.6.8 known as Rosetta that would allow you to run software written for the PowerPC Macs. 10.7 and later can't run that bridge software. You have one of several options:
Install 10.6 retail on a USB Flash drive, and run that application while booted from there.
Find an update designed for 10.7 or later of the software.
Find a combination of Virtualbox or Paralllels that can legally run a version of 10.6 side by side with your 10.7 software.
Run Windows on your Mac with Virtualbox or use CrossOver that requires no Windows to run a Windows version of your application.
Your Mac is an iMac Intel. I will ask a moderator redirect your thread to the 10.7 forum, and no action is needed on your part. -
Error when installing DI:J2EE Engine J00 of SAP system WS3 did not reach st
I am trying to install WAS Dialog Instance,but found error :
first run \Master\IM01_NT_I386\SAPINST\NT\I386\sapinst.exe
then set some parameters as usual and start installation.
when coming to phase 10 of 11:start sap j2ee engine,the log shows as follows:
INFO 2007-04-20 14:46:09
J2EE Engine J01 of SAP system WS3 did not come up after 623 seconds: waiting for another 20 seconds.
and at last it gives up,shows:
ERROR 2007-04-20 14:54:31
CJS-20058 J2EE Engine J01 of SAP system WS3 did not reach state "Starting Applications" after 1126 seconds: giving up.
I dont know how to handle this , pls help .thank you.Hi,
The problem could be with any of the following.
1>check JDK version you are using. use supported JDK in case if you you don't have
2>check your memory parameters. Notes 597187, 552522
might be of help.
may be the problem could be with the Heap Size.change it to value (ex:1024 MB) and try if it works.
also
3>check whether you started in safe mode. if so, change it to normal mode.
reward if it helps -
CJS-20058 J2EE Engine JC02 of SAP system B00 did not reach state "Starting
Error when reached the 21st step of the installation - Starting J2EE. The error message was CJS-20058 J2EE Engine JC02 of SAP system B00 did not reach state "Starting Applications" after 1121 seconds: giving up. The log showed the installation kept trying to start the service, and then change users.
Hi,
The problem could be with any of the following.
1>check JDK version you are using. use supported JDK in case if you you don't have
2>check your memory parameters. Notes 597187, 552522
might be of help.
may be the problem could be with the Heap Size.change it to value (ex:1024 MB) and try if it works.
also
3>check whether you started in safe mode. if so, change it to normal mode.
reward if it helps -
Please helpJ2EE engine JCO did not reach the "starting application" state
Hi,
I get the following error "J2EE engine JCO did not reach the "starting application" state" when I try to install my Java components using SAP Development Studio.
When I checked my std_servero.out the get the following error
[GC 65868K->39262K(128320K), 0.0173335 secs]
[GC 65942K->39031K(128320K), 0.0071339 secs]
[GC Full GC[Unloading class com.sap.engine.customizing.ccms.CustomizePerformanceMTEObjectImpl0]
[Unloading class com.sap.engine.customizing.ccms.CustomizeSingleMessageMTEHomeImpl0]Hello Santhi
The GC messages you see are just an indication of the garbage collector activity. It is not an error.
I'm not sure about what you are doing with the Developer Studio. I guess your WAS Java is already installed, is it right? Are you able to start the visual administrator? Please, paste here the exact error you receive.
Regards,
Désiré -
Have an Iphone 5 and had to restore. I recieved text message and replied after restore but they are no longer in thread.I did not erase. past messages still exist. Did sending party delete them? If so can I retreave them?
No, they probably got lost out there somewhere. They're gone.
-
I forgot the security question and did not reach me any e-mail from an email technical support for the alternative I hope to help
Alternatives for Help Resetting Security Questions and/or Rescue Mail
1. If you have a valid rescue email address, then use this procedure:
Rescue email address and how to reset Apple ID security questions.
2. Fill out and submit this form. Select the topic, Account Security. You must
have a Rescue Email to use this option.
3. This is the only option if you do not already have a valid Rescue Email.
These are telephone numbers for contacting Apple Support in your country.
Apple ID- Contacting Apple for help with Apple ID account security. Select
the appropriate country and call. Ask to speak to the Account Security Team.
Note: If you have already forgotten your security questions, then you cannot
set up a rescue email address in order to reset them. You must set up
the rescue email address beforehand.
Your Apple ID: Manage My Apple ID.
Apple ID- All about Apple ID security questions. -
I recently had to have a migration done on my Mac Desktop. Since then I keep getting this message on my MacBook regarding my calendar: "The server responded with an error." Its been asking me to check my ID and password, which I did not change. What do I do to correct the problem?
That's probably the MobileMe or iCloud password.
Go to System Preferences > Mobile Me (or iCloud). If you're not logged-in, do so. If you are, log out and back in again. -
Forgot Answer Questions safety tried to re-send a lot of email did not reach any messages to re-ask safety
I can not buy any program that I forgot to ask him answer safety
Please help and send me a re-liquefaction answer to the same email1) Apple ID: All about Apple ID security questions
If necessary
2) See Here... ask to speak with the Account Security Team...
Apple ID: Contacting Apple for help with Apple ID account security
3) Or Email Here > Apple Support iTunes Store Contact -
Dolphin / Kde 4.10.4 kex error : did not find one of algos zlib@openss
When I try to sftp:// via Dolphin into my Android slate I'm seeing this error:
kex error : did not find one of algos [email protected],zlib in list none for compression algo client->server
I can sftp without any issues in the terminal.This problem connected with proxy-setings.
As the first steps you should try:
1. export system env variable:
http_proxy=http://www-proxy.ru.oracle.com:80
https_proxy=https://www-proxy.ru.oracle.com:80
no_proxy=127.0.0.1,localhost
and you can also export
export OS_TENANT_NAME=admin
export OS_USERNAME=admin
export OS_PASSWORD=root
export OS_AUTH_URL=http://<conntroller_IP>:5000/v2.0/
2. and than restart mysqld, if it is running, stop iptables and repeat installation process from beginning with the currently generated answer file
if we are exporting variable OS_PASSWORD, its value should be the same as value for CONFIG_KEYSTONE_ADMIN_PW in the currently generated answer file.
This OS_PASSWORD will be written by packstack in the /root/keystonerc_admin file and will be used as admin's password for login to Openstack dashboard.
Maybe you are looking for
-
When I create a new mailbox in mail.app, the mailbox does not appear in the list of mailboxes
I am trying to create a new mailbox in mail.app, but it never appears in the list of mailboxes. This USED TO WORK.
-
Dose anyone know where one could find a dvd copying program like the windows based dvd decripter, and dvd shrink. it would be great if anyone knows of any.
-
Hi there, i wrote a message to JMF but i m not it is relevant with that topic. So added it here. I am making a instant messaging and video chat application with jmf. For this project , which one is usefull i am not sure. Can anyone help me? , For ins
-
After I updated my mac with OS X maverick my parallel stoped
after I updated my mac with OS X maverick my parallel stoped so that i can not open the windos 8 that I have on my mac so what is the selution
-
[feature request] Save original image when doing HDR
As the subject says - would be very nice to have an option to be able to get both images saved - HDR and the normal shot. iPhone5 that I also use has this option and it's very handy, please implement it. I shoot a lot on the go and sometimes the came