Looking for a serial driver for an agilent 4395A to work with labview

Can only find one for gpib I have no interface for gpib on my PC but i do have a rs232/gpib converter and was wondering if I could get a serial driver for the agilent 4395A for this.
Thanks

I've only used the RS232/GPIB converter to go from a GPIB bus to a serial instrument so I can't speak for going the other direction but I would give it a try. However, you have big problems with the driver if its the same one I just downloaded from NI. It's not really what I would call a driver at all but an application program meant to be used stand alone. There is no breakout of instrument functions into subVIs and none of the controls or indicators are on the connector so you can't even use the high level app as a subVI without a lot of work. It is a contributed driver but I'm surprised NI accepted it because it doesn't follow any of the published rules for an instrument driver. It's not even a good example of program design, imho. There is a VISA dr
iver available from Agilent here and I would try that instead. To use a VISA driver with a serial port, you just specify the VISA resource name for that port instead of the GPIB resource name. For example, a GPIB resource name of an instrument with an address of 5 would be "GPIB::5::INSTR". To communicate to your instrument over com port 1, the VISA resource name is "ASRL1::INSTR". If the instrument has a serial port in addition to the GPIB, you could also try skipping the converter. Some VISA drivers work fine either way.

Similar Messages

  • Looking for graphics adapter driver for Presario c700 video

    Looking for graphics adapter driver for Presario c700 video

    Please read the XP Downgrade Guide at the link below:
    http://h30434.www3.hp.com/t5/Notebook-Operating-sy​stems-and/General-XP-Downgrade-Guide-for-HP-Laptop​...
    The guidance for installing XP on your model series can be found under the section labeled 2. Moderate Models.

  • I am looking for a Mac driver for a Muratec MFX 1430 printer/fax/copier.  Is there one out there for a Mac?

    Looking for a Mac driver for a Muratec MFX-1430 printer/fax/copier
    is there such an animal out there?

    http://www.muratec.com/new/support/drivers.asp does not appear to support that model at all on the Mac.
    Some open source drivers* may exist to support it.
    * Links to my pages may give me compensation.

  • Developing serial driver for hp54615B

    Hellow LabVIEW User's,
    I am dveloping a serial driver for hp54615B scope. i went through the GPIB driver for the hp54615B which NI has developed. In this driver hp546xx Read Delay.vi which commands of hp54615B you are setting to the following inputs.
    1) what does the following parameters corresponds to
    a) Channel1 edge count
    b) Channel2 edge count
    2 ) Similarly in hp546xx Read Min Max Waveform.vi
    what is the min waveform array and max waveform array consists of when i acquire some 5000 points.
    3) Similarly in hp546xx Configure Record length.vi
    what are these parameters corresponds to
    a) time per record .
    b) minimum record length (is this input same as no of points to acquire ).
    c) acquisition start time
    inputs corresponds to and which command should i pass to achieve this.
    waiting for reply
    Thanks & Regards
    anil

    I'm thinking that you are using IVI driver. IVI driver from NI site is distributed with source code. This driver does not support serial interface, but you can change source code and recompile DLL. LabVIEW IVI driver is calling DLL.
    Driver will require following changes:
    1) in IviInit function you must set for serial interface some attributes. (VI_ATTR_TERMCHAR, etc.)
    2) for serial interface you cannot use events. WaitForOPCCallback must be changed.
    3) All functions which read binary data must be changed. You must disable term. character during binary transfer.
    For more details download tktds3x0 driver. This driver supports serial interface.
    >-----------------------------------------------------
    * hp546xx Read Delay.vi call for edge count param
    etrers following command:
    MEASEF DEL,,
    If slope is set to falling, value is inverted.
    For example:
    Channel1 Slope: Rising
    Channel1 Edge Count: 2
    Channel2 slope: Falling
    Channel1 Edge Count: 5
    Command: MEASEF DEL,2,-5
    * Read Min Max Waveform you can call only if the acquisition type is peak detect. In this case scope returns two waveforms. Odd elements in buffer(WAVATA?) are elements of min waveform and even elements are elements of max waveform.
    * hp546xx Configure Record Length.vi
    * minimum record length - is the minimum number of points which you require. If you set this value to value which is not supported but is less as maximum for example 4901, driver sets to instrument number of points WAVOIN 5000. Driver will guarantee that read function returns wavefrom with this size.
    * time per record is time for aquire all points. (TIM:RANG)
    * This time represents the time of first element in waveform. if you set 0.0 -> first el
    ement of waveform is trigger. (TIMEL) the range depends on the time per record.
    Regards,
    Zdenek

  • Looking for HP 5371A driver for Labview 6.1?

    want to communicate with HP5371A by PC over GPIB port

    I think that device is too old for finding a driver for labview. If you have all the GPIB command, it's easy to program. I made it for another type of instrument.
    Benoit Séguin
    Software Designer

  • Looking for a way to get my Product ID and Vendor ID so I can enable my Radium 49 USB MIDI keyboard to work with Labview 7

    Looking for the Product ID and Vendor ID for my Radium 49 USB MIDI keyboard to work with Labview 7
    Is there a tool to find out the Vendor ID and Product ID for a USB device?
    Example: of what I'm looking for
    The Product ID for National Instruments DAQPad-6020E is 0x12C0. The
    USB vendor ID is 0x3923. This is a 16-bit hexadecimal number(1093)
    (that is decimal 4243).
    Thanks for all the fast responses this newsgroup RULES!!!!!!!!!!!!

    http://digital.ni.com/public.nsf/allkb/335A90747734097886257070006415B9
    How To Find The Vendor and Product ID for USB Devices?
    Primary Software: Driver Software>>NI-VISA
    Primary Software Version: 3.3.1
    Primary Software Fixed Version: N/A
    Secondary Software: N/A
    Problem:
    I want to make an NI-VISA driver that requires the vendor and product ID?
    Solution:
    There is a utility called USBView,
    free from Windows, attached below, which you can use to view what is
    connected to your computer's USB ports. It is necessary to load this
    program and connect the USB device in development. Upon selecting the
    device in USBView, one can then look on the right side of the
    application window to obtain the Product ID and Vendor ID. This will
    allow you to enter in the correct IDs when creating a driver .inf file
    when using the VISA Driver Development Wizard. For more information
    about how to use the VISA Driver Development Wizard see the related
    links below.
    Note: It is necessary to keep the hexadecimal
    (0x####) format. Do not remove the "0x" hexadecimal format preceding
    the ID number. 

  • Adobe creative cloud is asking for a serial number for updates - where do I get this from?

    Adobe Creative cloud is asking for a serial number for updates - where do I get this from
    we have recently Bought 5 x 1 year licences and been using this a month
    Michael

    Hi Mick,
    Please refer to the below link.
    http://helpx.adobe.com/creative-cloud/kb/ccm-prompt-serial-number.html
    Thanks

  • Hey Guys! Can i Ask for Licensure Serial Number for Photoshop CC 2014

    Hey Guys! Can i Ask for Licensure Serial Number for Photoshop CC 2014

    CC is licence via a subscription and activate by a sign in with a with a user ID and password that has a subscription.  Here is some of my Photoshop System Info the last line I'm including shows my serial number.That is where your serial number is.
    Adobe Photoshop Version: 2014.1.0 20140730.r.148 2014/07/30:23:59:59  x64
    Operating System: Windows 7 64-bit
    Version: 6.1 Service Pack 1
    System architecture: Intel CPU Family:6, Model:13, Stepping:7 with MMX, SSE Integer, SSE FP, SSE2, SSE3, SSE4.1, SSE4.2, AVX, HyperThreading
    Physical processor count: 12
    Logical processor count: 24
    Processor speed: 1995 MHz
    Built-in memory: 40886 MB
    Free memory: 33785 MB
    Memory available to Photoshop: 37129 MB
    Memory used by Photoshop: 94 %
    3D Multitone Printing: Disabled.
    Touch Gestures: Disabled.
    Windows 2x UI: Disabled.
    Image tile size: 1024K
    Image cache levels: 4
    Font Preview: Huge
    TextComposer: Latin
    Display: 1
    Display Bounds: top=0, left=0, bottom=1080, right=1920
    Display: 2
    Display Bounds: top=0, left=-1360, bottom=768, right=0
    OpenGL Drawing: Enabled.
    OpenGL Allow Old GPUs: Not Detected.
    OpenGL Drawing Mode: Advanced
    OpenGL Allow Normal Mode: True.
    OpenGL Allow Advanced Mode: True.
    AIFCoreInitialized=1
    AIFOGLInitialized=1
    OGLContextCreated=1
    NumGLGPUs=1
    NumCLGPUs=1
    glgpu[0].GLVersion="3.0"
    glgpu[0].GLMemoryMB=2048
    glgpu[0].GLName="Quadro 4000/PCIe/SSE2"
    glgpu[0].GLVendor="NVIDIA Corporation"
    glgpu[0].GLVendorID=4318
    glgpu[0].GLDriverVersion="9.18.13.4052"
    glgpu[0].GLRectTextureSize=16384
    glgpu[0].GLRenderer="Quadro 4000/PCIe/SSE2"
    glgpu[0].GLRendererID=1757
    glgpu[0].HasGLNPOTSupport=1
    glgpu[0].GLDriver="nvd3dumx.dll,nvwgf2umx.dll,nvwgf2umx.dll,nvd3dum,nvwgf2um,nvwgf2um"
    glgpu[0].GLDriverDate="20140702000000.000000-000"
    glgpu[0].CanCompileProgramGLSL=1
    glgpu[0].GLFrameBufferOK=1
    glgpu[0].glGetString[GL_SHADING_LANGUAGE_VERSION]="4.40 NVIDIA via Cg compiler"
    glgpu[0].glGetProgramivARB[GL_FRAGMENT_PROGRAM_ARB][GL_MAX_PROGRAM_INSTRUCTIONS_ARB]=[6553 6]
    glgpu[0].glGetIntegerv[GL_MAX_TEXTURE_UNITS]=[4]
    glgpu[0].glGetIntegerv[GL_MAX_COMBINED_TEXTURE_IMAGE_UNITS]=[192]
    glgpu[0].glGetIntegerv[GL_MAX_VERTEX_TEXTURE_IMAGE_UNITS]=[32]
    glgpu[0].glGetIntegerv[GL_MAX_TEXTURE_IMAGE_UNITS]=[32]
    glgpu[0].glGetIntegerv[GL_MAX_DRAW_BUFFERS]=[8]
    glgpu[0].glGetIntegerv[GL_MAX_VERTEX_UNIFORM_COMPONENTS]=[4096]
    glgpu[0].glGetIntegerv[GL_MAX_FRAGMENT_UNIFORM_COMPONENTS]=[4096]
    glgpu[0].glGetIntegerv[GL_MAX_VARYING_FLOATS]=[124]
    glgpu[0].glGetIntegerv[GL_MAX_VERTEX_ATTRIBS]=[16]
    glgpu[0].extension[AIF::OGL::GL_ARB_VERTEX_PROGRAM]=1
    glgpu[0].extension[AIF::OGL::GL_ARB_FRAGMENT_PROGRAM]=1
    glgpu[0].extension[AIF::OGL::GL_ARB_VERTEX_SHADER]=1
    glgpu[0].extension[AIF::OGL::GL_ARB_FRAGMENT_SHADER]=1
    glgpu[0].extension[AIF::OGL::GL_EXT_FRAMEBUFFER_OBJECT]=1
    glgpu[0].extension[AIF::OGL::GL_ARB_TEXTURE_RECTANGLE]=1
    glgpu[0].extension[AIF::OGL::GL_ARB_TEXTURE_FLOAT]=1
    glgpu[0].extension[AIF::OGL::GL_ARB_OCCLUSION_QUERY]=1
    glgpu[0].extension[AIF::OGL::GL_ARB_VERTEX_BUFFER_OBJECT]=1
    glgpu[0].extension[AIF::OGL::GL_ARB_SHADER_TEXTURE_LOD]=1
    clgpu[0].CLPlatformVersion="1.1"
    clgpu[0].CLDeviceVersion="1.1 CUDA"
    clgpu[0].CLMemoryMB=2048
    clgpu[0].CLName="Quadro 4000"
    clgpu[0].CLVendor="NVIDIA Corporation"
    clgpu[0].CLVendorID=4318
    clgpu[0].CLDriverVersion="340.52"
    clgpu[0].CUDASupported=1
    clgpu[0].CUDAVersion="6.5.12"
    clgpu[0].CLBandwidth=7.48422e+010
    clgpu[0].CLCompute=184.394
    License Type: Subscription
    Serial number: 96040035116912554961

  • Can't install my  adobe creative suite after i put the serial number. its asking for the serial number for cs3 and i don't have that.... what do i do?

    can't install my  adobe creative suite after i put the serial number. its asking for the serial number for cs3 and i don't have that.... what do i do?

    ANd what exactly? You hav not told us, what you are actually trying to install onto what system and other details....
    Mylenium

  • Where do I go for a safe driver for the Mac for use with Altec Lansing Technologies IMT227 OrbitM Ultra Portable Speakers?

    Where do I go for a safe driver for the Mac for use with Altec Lansing Technologies IMT227 OrbitM Ultra Portable Speakers?

    This is an Altec Lansing IMT227 OrbitM etc
    Is this what you have?
    Here is the specification, please note, no USB
    You are either mistaken or talking about a different model.

  • I'm on the 899 photography package and its asking for a serial number for adobe photo shop ?

    Hi i just bought the pay monthly photography package and its asking for a serial number for adobe photshop ?

    Sign in, activation, or connection errors | CS5.5 and later
    Mylenium

  • I am being asked for a serial number for a software update for aperture.I bought this from the app store and can't find the serial number

    I am being asked for a serial number for a software update for aperture.I bought this from the app store and can't find the serial number.any ideas?

    What exactly does the dialog widow say? Can you show us a screen shot?

  • I try to download components for CS Cloud. Adobe Application Manager freezes. Working with Win XP

    I try to download components for CS Cloud. Adobe Application Manager freezes. Working with Win XP. What can I do?

    You need to provide a lot more info like what apps you are trying to download, what exactly seems to be going on, exact system specs, Internet connection info, whether AAM is up to date and so on....
    Mylenium

  • I want to get a portable power pack for recharging my iphone5 and ipad air. What works with both?

    I want to get a portable power pack for recharging my iphone5 and ipad air. What works with both?

    http://www.amazon.com/gp/product/B00D5T3QK4/ref=oh_details_o03_s00_i00?ie=UTF8&p sc=1

  • If I buy the Adobe Export PDF for $23.99/yr - will that allow me to work with a PDF fillable form -- then rename and save that form?

    If I buy the Adobe Export PDF for $23.99/yr - will that allow me to work with a PDF fillable form -- then rename and save that form?

    I want to fill in the blanks on a PDF form --
    Then I want to rename the form and save it.
    Beverly Visitacion
    Location Scout/Manager
    Cell:  305 322-1586
    Fax:  305 328-9666
    [email protected]
    Michael Jarvis
    Location Scout/Manager
    Cell:  305 335-6266
    [email protected]
    "ARMS & THE DUDES"

Maybe you are looking for

  • Macbook pro unibody doesn't recognize hdd, is it cable or motherboard?

    Hi, A few weeks ago I replaced my hdd in my macbook pro 13inch med 2010 with a ssd. Some weeks after I did it, my macbook didn't boot up anymore, it showed a flashing folder. I put my old hdd in and it still doesn't boot up. I use my macbook now by b

  • Purchase Order Based on MRP

    Hi, when ever i create PO from the order recommendation based on MRP i see same items in multiple rows. For eg If raw material RM1 and RM2 are to be ordered based on MRP and required qty is RM1=10 , RM1-20, RM2=4, RM2=9 when i raise PO through Order

  • Oracle.jbo.TooManyObjectsException: JBO-25013: Too many objects match the

    I have developerd a OAF and deployed in apps. When i am running that page it gives me error oracle.jbo.TooManyObjectsException: JBO-25013: Too many objects match the primary key oracle.jbo.Key[0]. and hides the Lines region. when i refresh (F5) the p

  • Cluster (Load balancing) implementation in obiee 10g

    Hi All, We need to implement clustering (Active-Active for Load balancing) in our project. We use both analytics and bi publisher. We also need to deploy analytics/bipublisher in to weblogic server for SSO purpose. Now we have two machines. As of now

  • CSS rendering in design window

    I am doing some simple CSS layout (nothing tricky at all), and noticing that there are significant differences between how the page looks in a browser, and how it looks in Dreamweaver. The layout is 3 floated columns with header and footer - a total