Low rates of (modulus) breakpoint re-enabling

Hello!
I am using the motion control NI7334 and I need the breakpoint output to trigger my measurements.
In a quite simple program I re-enable the (modulus) breakpoint each time it occurred. The fastest repetition rate I could generate to enable the breakpoint was about 110 Hz, with higher breakpoint frequencies it becomes irregular, means I don't get all breakpoints. I'm worried if it becomes even worse when my program will be more complex. These low rates for re-enabling the breakpoints are a problem of the labview-code, of windows xp or of the communication between software and PCI-board?
Attachments:
motiontest.vi ‏81 KB

The reason why you can't reach faster breakpoint reenable rates is a
mixture of all the reasons that you have suggested plus some internal
delays on the board. There is not much you can do about that.
There are several options for better breakpoint performance:
You could contact your local NI branch to upgrade your NI 7334 to a NI 7354.
The 735x boards provide buffered breakpoints with 2 kHz trigger rate
and periodic breakpoints with 4 MHz. Reenabling is done automatically
on the board.
You could use the counter inputs of a DAQ-board like the PCI-6220 (two counters) or a dedicated counter board like the PCI-6601
(four counters) to generate the trigger signals by dividing down the
frequency of the encoder signals. As this runs in hardware, you will
also be able to generate triggers with rates up to several MHz.
I hope that helps,
Jochen Klier
National Instruments Germany

Similar Messages

Max. sample frequency with "Modulus Breakpoint (on-board re-enable).vi"

Hi all,
I'm using the PCI-7344 board and I'd like to trigger an external device. The trigger frequency should be very high (> 4 kHz).
Is it possible to realize such a sample rate with breakpoints and an onboard program like: "Modulus Breakpoint (on-board re-enable).vi".
I don't need a visual indicator and so I don't need the 10 ms delay in the second part.
What is the timeout in the first part for?
Thanks in advance for your help.
Best regards
Attachments:
Modulus_Breakpoint_(on-board_re-enable).vi ‏114 KB

Depending on the movement of a xy - stage (controlled by the motion controller) I'd like to trigger a pulsed laser. Maybe every 2 µm I need a short TTL pulse to release a laser pulse.
I tried a software based solution as well as a on-board solution. Both ways are working well but unfortunately the software based solution is limited to 20 Hz and the on-bord solution is limited to 50 Hz.
Because of that I have to decrease Vmax in my application to 100µm/s.
Well , it would be much easier to trigger the laser with an adjusted frequency. The problem is the acceleration and deceleration of the stage. Because of that the pulses will overlap much more at the edges and that's the fact I wanna avoid.
Thanks for your help. Best regards

Vendor - Tax deduction at lower rate - MIRO & FB60

Hi all,
Currently we are having one issue of u201CTax deduction at lower rateu201D for a Vendor who is having such certificate with him.
For amount purpose we have set the SPRO setting but the user is asking for the date control also since the Vendor is having the relevant certificate till 31.03.2012 and after that, lower rate Tax deduction will not be allowed.
Simple option is to change the Vendor Master with the original tax type+ Tax code (Normal Rate) combination to calculate tax at the normal rate. But if could not cross the amount limit before 31.03.2012 then that will be difficult to keep an eye on date i.e. 31.03.2012 and then change the master data of u201CNu2026u201D No. of Vendors .
We want to put a condition in a system as; system should check the system date with the tax type date to get a date control. We have restricted the date of u201Cnewly created tax typeu201D till 31.03.2012.
In case of MIRO testing, we have use a user exit which is correctly comparing the system date with the tax type date in runtime. If the tax type date is older than system date then system is throwing an error to change the master date (FK02 / XK02) of subject vendor.
In case of FB60 we are facing a problem since not able to cross confirm the tax type date with the system date. We are trying BTE u2013 1140 for FB60 but in runtime we are not able to get the tax related details / tables.
Is there any workaround or way in BTE u2013 1140 for FB60?
Regards,
Shridhar
Edited by: Shridhar Sawant on Nov 2, 2011 2:23 PM

Hi Ramesh,
In the SAP Std. setting of Formula we are maintaining one more line for same TAX TYPE + TAX CODE + COUNTRY combination but for the ending date of lower rate tax deduction.
Since there is no "To date" option in Formula setting, we are maintaining one more line For e.g. in the 1st line we have a date as 01.04.2011 (i.e. Valid from) and in the other line we have mentioned date as 01.01.2012 (i.e. To date) since Vendor is having the lower rate tax deduction certificate uptill 31.12.2011.
In the first line of formula (Valid from 01.04.2011) we have maintain :
To Base amt              W/tax    Reduction base amt.
175,000.00                 3.00               -
9,999,999,999.00     10.00     175,000.00
In the second line (Valid from 01.01.2012) of formula we have maintain :
To Base amt             W/tax    Reduction base amt.
9,999,999,999.00    10.00               -
Cross confirming the various scenarios since date accumulation of tax setting is on in Tax Type that we are considering.
Will confirm to you the change suggest by you.
If these changes doesn't work then we have to go to the option of User exit or BTE for MIRO and FB60 testing.
Have any idea about the above mention settings ?
Regards,
Shridhar

TDS at lower rates for certian limit

Hi experts,
Income Tax Department gives vendors certifcate for lower deduction of
tax u/s 197, which is a permission to a payer to deduct NIL Tax or tax
at a lower rate. This permission is generally given for a Financical
Year. However, recently it is seen that these certificates are for a
certain Limit. eg: a vendor is given a certificate u/s 197 upto a limit
of Rs.10,00,000/- for NIL deduction. This means that as soon as the
payment to this vendor crosses Rs.10,00,000/- TDS is to be deducted at
the normal rates. THIS NEEDS TO BE CONFIGURED IN THE SYSTEM so that the
correct TDS is deducted and paid.
Regards
venkat reddy

Dear Friend
In current Sap scenario it is not possible to have value cap on the withholding tax.
What we are doing is manually keeping tab on the value cap every month and The user is updated with the available limits. Once the cap is reached, the exemption validity date is changed from 31.03.2008 to the date on which the last invoice was posted. Any subsequent invoice attracts WT at full rate.
Somewhat cumbersome particularly in year end when most of the limits are reached but cannot help it.
We had suggested some customisation wherein the exemption percentage would be checked with the accumulated tax base amount but the same was rejected based on cost benefit ratio.
Would appreciate if you could think of something new and share the same.
Regards
Mukesh

ORA-25307: Enqueue rate too high, flow control enabled

I am stuck. I have my stream setup and they were previously working on two of my dev environments well. Now when I get the streams setup the CAPTURE process has a state of "CAPTURING CHANGES" for like 10 seconds and then changes to state "PAUSED FOR FLOW CONTROL". I believe this is happening because the PROPAGATION process is showing an error of "ORA-25307: Enqueue rate too high, flow control enabled".
I don't know what to tweak to get rid of this error message. The two environments are dev databases and there is minimal activity on them so i don't think it's a case of the APPLY process is lagging behind the PROPAGATION process. Has anyone run into this issue?? I've verified my db link works, my stream admin user has dba access. Any help or advise would be greatly appreciated.
thanks, dave

As rule of thumb, you don't need to set GLOBAL_NAME=TRUE as long as your are 100% GLOBAL_NAME compliant.
So, setting GLOBAL_NAME=TRUE will not have any effect if your dblink is not global_name compliant
and if your installation is global_name compliant, you don't need to set GLOBAL_NAME=TRUE.
The first thing when you diagnose is to get the exact facts.
Please run this queries both on source and target so that to see what are in the queues and where.
Run it multiple time to see if figures evolves.
- If they are fixed, then your Streams is stuck in its last stage. As a cheap and good starting point, just stop/start the capture, propagation and target apply process. Check also the alert.log on both site. when you have a propagation problem, they do contains information's. If you have re-bounced everything and no improvement then the real diagnose work must start here but then we know that the message is wrong and the problems is elsewhere.
- if they are not fixed then your apply really lag behind for what ever good reason, but this is usually easy to find.
set termout off
col version new_value version noprint
col queue_table format A26 head 'Queue Table'
col queue_name format A32 head 'Queue Name'
select substr(version,1,instr(version,'.',1)-1) version from v$instance;
col mysql new_value mysql noprint
col primary_instance format 9999 head 'Prim|inst'
col secondary_instance format 9999 head 'Sec|inst'
col owner_instance format 99 head 'Own|inst'
COLUMN MEM_MSG HEADING 'Messages|in Memory' FORMAT 99999999
COLUMN SPILL_MSGS HEADING 'Messages|Spilled' FORMAT 99999999
COLUMN NUM_MSGS HEADING 'Total Messages|in Buffered Queue' FORMAT 99999999
set linesize 150
select case
when &version=9 then ' distinct a.QID, a.owner||''.''||a.name nam, a.queue_table,
              decode(a.queue_type,''NORMAL_QUEUE'',''NORMAL'', ''EXCEPTION_QUEUE'',''EXCEPTION'',a.queue_type) qt,
              trim(a.enqueue_enabled) enq, trim(a.dequeue_enabled) deq, x.bufqm_nmsg msg, b.recipients
              from dba_queues a , sys.v_$bufqm x, dba_queue_tables b
        where
               a.qid = x.bufqm_qid (+) and a.owner not like ''SYS%''
           and a.queue_table = b.queue_table (+)
           and a.name not like ''%_E'' '
   when &version=10 then ' a.owner||''.''|| a.name nam, a.queue_table,
              decode(a.queue_type,''NORMAL_QUEUE'',''NORMAL'', ''EXCEPTION_QUEUE'',''EXCEPTION'',a.queue_type) qt,
              trim(a.enqueue_enabled) enq, trim(a.dequeue_enabled) deq, (NUM_MSGS - SPILL_MSGS) MEM_MSG, spill_msgs, x.num_msgs msg,
              x.INST_ID owner_instance
              from dba_queues a , sys.gv_$buffered_queues x
        where
               a.qid = x.queue_id (+) and a.owner not in ( ''SYS'',''SYSTEM'',''WMSYS'') order by a.owner ,qt desc'
   end mysql
from dual
set termout on
select &mysql
/B. Polarski

Disabling Low Rates on a WLC

I was wondering if disabling low rates could cause issues for clients in higher density areas. For example, if I have 9 meg as the minimum allowed rate, what is actually taken under consideration for that rate? If I have a significant number of clients connected to that AP, is that going to be taken under consideration by the controller when calcultating the minimal supported rate to all clients? Or does it only take under consideration the distance between the nearest AP and the client and the obstructions in between?

Mandatory rate is what the client must be able to negotiate at. Supported rate are rates the WLC will allow the client to negotiate to. Disabling the lower data rates only affect old devices that might require 1 or 2 Mbps data rate. Distance from the AP is a factor as what the client and ap negotiate at. In a high density deployment for example, I have had 24mbps as mandatory and everything below 11 or 12 disabled and the rest supported. I might also add another mandatory rate if I'm using multicast. You need to know your RF to really decide what you can have a a mandatory and it supported.
Sent from Cisco Technical Support iPhone App

Saving Data at lower rate

Hi ,
I am acquiring data through DAQ . The sample rate is 20k and sample to read is 2k. These setting satisfies my requirements. But the data that I save is huge since I intend to aquire it for hours. Hence I would appreciate if somone could tell me how to save data at lower rate i.e. without changing the "sample rate" or "sample to read". Moreover if i could set the saving frequency of data each time I start the aqusition.
Thanks in advance for help.
Solved!
Go to Solution.
Attachments:
Data Aq.vi ‏867 KB

I haven't used it, but most of the questions I see regarding logging large amounts of DAQmx data reccomend using TDMS to record data.
There are LabVIEW functions as well as plugins for Excel, OpenOffice and MATLAB for loading TDMS data.
TDMS Direct Integration in NI-DAQmx Logging
The NI TDMS File Format
Now is the right time to use %^<%Y-%m-%dT%H:%M:%S%3uZ>T
If you don't hate time zones, you're not a real programmer.
"You are what you don't automate"
Inplaceness is synonymous with insidiousness

Lower Rate TDS upto certain limit

I have one vendor who is applicable lower rate of TDS upto certain limit, but after certain limit system have to charge normal rate of TDS, is it possible to track and post such type of transaction in SAP?

HI,
It is possible with help of below config.
Accumultion + Formula's
please create separate tax type and tax code for this particular vendor.
tax type
accumulation , per year start month 4
tax code
check box " form w/tax"
Define the formula's for withholding tax.
upto
50000 5%
9999999999999 10 %
above is very specific to one vendor.
Regards
Madhu M

My new airport extreme transmits at low rates (0-54)and is intermittent? Help!

I need help figuring out why my new 6th generation airport extreme signal is transmitting at a low rate (0-54) and when streaming the signal goes in and out? My equipment is as follows... I have a moterolla extreme DOCsis 3.0 modum, comcast 30 mpbs, and new apple extreme with current airport utility 7.7.1. Any ideas or troubleshooting tips?

When you created your wireless network with the Airport Extreme, did you select having your wireless network backwards compatible with "b/g" devices? If your wireless network was created as "N" compatible for "N" compatible wireless cards only, an iPhone will not be able to connect to your wireless network since the iPhone's wireless card is not "N" compatible.

VF01 tansaction Kurrf (Exchange Rate) need to change as enable

Hi all,
I need to change the Kurrf (exchange rate) for VF01 and Vf02 as enable.
Can u please suggest me how can i do this.
Regards
Madhu

Hi Madhu,
there are two options here.
One is by using the SHD0 T.Code by entering the valid values in the screen variant.
Second one is Press F1 on the field and check for technical information.
Check the program name and screen number.
Goto T.Code SE51,enter the program name and screen number in that.
Check the layout and in the field you requested there you can find in the layout.
Click on the field and go to attributes where you can make it as editable or inputtable text box.
Regards,
Krishna.

Buffered edge count FIFO overflow even at very low rates

Dear Forums,
I am trying to use a PXI-6608 to timestamp the sample clock of a PXI-4498 during analog input. Because the sample rate will be on the order of 20KHz, I want to use a pulse generation task on one counter to divide it down by a factor of 1000, then use that pulse as the gate and the 10MHz clock on the 6608 as the source in a buffered edge -- I expect about 20 edges per second, which should be very manageable to retrieve over DMA.
The result is that I get error -200279 ("attempting to read samples no longer available") immediately after the vi starts, before I have retrieved even one count.
This is my first stab at using DAQmx for counter/timer instead of the old DAQ drivers, so I'm sure I've done something wrong, but I can't figure out what.
I've attached the vi if that helps.
Thanks!
Cas
Solved!
Go to Solution.
Attachments:
simplified chassis test.vi ‏314 KB

It appears that you have your gate and source backwards. The sample clock should be ctr0internaloutput and the count edges terminal should be the 10 MHz clock. You are getting the buffer overflow error because the FIFO on the card is only 2 samples and at 10 MHz these are being rewritten was faster than a computer could possible pull them off the card.
Doug Farrell
Product Manager - Condition Monitoring
National Instruments
National Instruments Condition Monitoring

IPad gets lower rate than iPhone

Looking at my Airport Extreme, I see that my iPad is connected with a wireless rate of 39Mbps. My iPhone is getting 54Mbps. They are both about 6 feet away from the AE. How can this be?

Your iPhone is connecting using 802.11g while the iPad uses 802.11n. For some reason it gets limited to 39mbps. If you set up your Airport Extreme to only allow G, the iPad will get 54 too. And in my case be more stable as well.

Early termination due to superior competitive ISP's with faster speeds and lower rates

Since Netfusion is no longer commercially competitive due to its slowness, data caps and high costs, I want to terminate early but I don't see how to do this or how much Verizon plans to assess a fee. Does anyoone know how to find out how much extra it costs to terminate or how to proceed with a termination?
Thanks

If you have the jetpack, the ETF is $175 minus $5 per month completed
If it's the HomeFusion, the ETF is $350 minus $10 per month completed

Why is it that I can't do a continuous streaming to disk with a 5102 scope card (PCI) when I can do it with a DAQ Card of much lower specs (my requirement is for small sampling rates only)?

I am told that the 5102 Card (PCI) does not support continuous streaming of data to the hard disk. My application requires only very low sampling rates. If I can do it with a low spec DAQ Card using LabView why can't I do it with this card?

Hello,
The PCI-5102 is a high-speed digitizer card that has a slightly different architecture than the DAQ cards and was not built with the ability to stream data to the PC. However if you are sampling at low rates you can still acquire up to 16 million samples, which is done by using dma to tranfer data from the onboard memory on the 5102 to the PC memory. However, you will not be able to save the data to disk until the acquisition is complete.
Another option would be to purchase either a DAQ card or a PCI-5112. Both boards can continuously stream data to the host PC and you should not run into any PCI bus limitations if you are stream to disk at relativiely slower rates.

VMS & IPC Low MOCA speeds Check your COAX!

To much load on the COAX? Two 4-way by directional splitters and the router sits on the first splitter.
Make sure in is in and out is out.
Quantum TV ROCKs! Now that I removed the sand.
Enable Client Ethernet option with hopes they built it with Gigabit!
System Log
LAN Coax
LAN Coax Link Low Rate <TX 89Mbps/RX 113Mbps>
Actiontec issues, did not see this prior to Quantum TV?
Why does the router report this if the Ethernet is supporting the computers at Gigabit, and MOCA LAN is supporting the IPC Clients?
The clients should not care at this MOCA speed?
Does it matter that the LAN is running slow, since the MOCA WAN and LAN are at a different frequencies, and MOCA WAN not used with Ethernet WAN configurations?
Or would this too cause a bottle neck on the bridge, because with Gigabit LAN it should not?
Come on Verizon get a router with MOCA 2.0 and decent Wifi!
All VMS and IPC devices report a good SNR. Is this only an issue with the load on MOCA it you are running MOCA WAN?
ONT, 1- MI424WR-GEN3I, 1- VMS-1100, 3- IPC-1100, and 1- Media Center Network Tuner. Now say I add another VMS-1100 or more clients.
The CSR was clueless, and kept wanting access to my private network and PC. I don't think so. Do what you wish on your network, mine is mine!
Solved!
Go to Solution.

Make sure in is in and out is out.
Quantum TV ROCKs! Now that I removed the sand.
Check your in and out splitter connections and make sure they are tight and in is in and out is out.
I will be the first to admit when I double check my work and find I was wrong. Hey what do you want when your reconnecting coax cables after running Media Center extenders on Ethernet for 16 months in anticipation.

Low rates of (modulus) breakpoint re-enabling

Similar Messages

Maybe you are looking for