Lower security to higher security interface PAT.

Hi,
Can we have PAT with nat and global statements for source natting a traffic from Lower security interface to Higher security? If nat & global can't achieve this, what are the Possibilities.
merci,
arun

When you specify a group of IP address(es) in a nat command, then you must perform NAT on that group of addresses when they access any lower or same security level interface; you must apply a global command with the same NAT ID on each interface, or use a static command. NAT is not required for that group when it accesses a higher security interface because to perform NAT from outside to inside you must create a separate nat command using the outside keyword. If you do apply outside NAT, then the NAT requirements preceding come into effect for that group of addresses when they access all higher security interfaces. Traffic identified by a static command is not affected.
nat (outside) 1 network netmaks outside
global (inside) 1 ip_address <--- used for PAT

Similar Messages

Ping from lower security interface to a higher

Hello,
I have a Cisco 5520 ASA firewall with a direct connection to a Checkpoint firewall. On the inside network of my ASA i have a server that needs to ping a server on the dmz on the Checkpoint and vice versa. So i have the correct routing and firewall rules on both devices.
I can successfully ping from my server on the INSIDE interface on the cisco asa to the server on the DMZ on Checkpoint but i cant ping in the other direction.
Q Is this because i am trying to go from a lower security interface on the asa to a higher one?
I cant be sure if the error is on my asa or the checkpoint because neither is showing anything in the logs?
Everything else on both firewalls is fine.
regards,
Kevin

Hi,
Its hard to tell what the actual problem is at the moment.
With regards to the "security-level" value, the situation is if the interface doesn't have an ACL configured on it then traffic sourced from networks behind it will be allowed to networks located behind interfaces of lower "security-level". If the source interface for the direction that is not working doesnt hold an ACL and has lower "security-level" than the destination interface then you will have to configure an interface ACL to allow this traffic.
Then again, the problem might be as simple as the server simply rejecting the ICMP Echo but allowing itself to ICMP Echo some remote destination and receive an Echo Reply for that. In other words, the server can ICMP remote hosts but wont accept ICMP Echo from remote hosts. It might reply to hosts on the directly connected network. So if there is no clear reason for the traffic to not go through I would consider checking the server software firewall.
It might also be that the working direction has been configured with Dynamic PAT and there is no correct translation for the other direction to enable sending ICMP to the server.
You can easily test the ASA configuration with the "packet-tracer" so that would be the first natural step to determening the reason of the problem or atleast narrowing it down.
packet-tracer input icmp 8 0
In the above command you would use the interface nameif behind which the ICMP Echo is coming from (8 0 = ICMP Echo). The source IP address is obvious. The destination IP address should be the NAT IP address of the server IF there is NAT being performed. If NO NAT is done for the destination then you naturally use the real IP address.
Hope this helps
- Jouni

Question on QoS for File-- SOAP synchronous high volume interface

Is it possible to have a File to SOAP (sender file adapter --> receiver SOAP adapter, synchronous - response needed by sender ) scenario with FIFO (first in first out). This is a high volume interface (about 8 messages/second). If FIFO possible, will a failed message block the succeeding messages?
My understanding is that QoS of receiver SOAP CC is Best Effort.
Thank you.

yes..EOIO will block the queues if its predecessor are not in final state...
for ur design u can rfer the below wiki...instead of RFC u can use soap adapter..
http://wiki.sdn.sap.com/wiki/display/XI/File-RFC-File%28Without%20BPM%29

Low Res to High Res Help!!!

I need some advise. I have still jpegs and tiffs that I need to convert up from a low resolution, without pixelating the picture (Low resolution to High Resolution. I own Adobe CS3(the suite)which include Photoshop. If photoshop is not the answer, please let me know what is. If photoshop is the answer, I can't seem to get the right tool within. Is it even possible? Simply changing the property of the image will make it larger, but very distorted/pixelated.
Thanks in advance for your help.

Youtube's specs can be obtained form the technical advice section of their site. I believe it's MPEG4, which is H.264. But you must not confuse the term resolution with image quality. Whatever you upload to to YT gets transcoded by their system before it gets mounted. There are hundreds of sites devoted to getting the best image up on YT, google is your buddy on that one. there are several places in the workflow where you can attempt to maintain image quality. it's tricky, depends on your content. encoding is all about maximizing image quality at various points. Action requires a higher bitrate that can be stolen from scenes that have little detail.
It's really hard to get good encoded video, especially up on YT.
bogiesan

How to pass the low value and high values for select options.

Hi,
       In selection screen I want to display the first date, last date of this month as a default value in low and high fields. Please exaplain me how.
Thanks and Regards,
Surya

hI,
     Very thanks ,
        I did it what u said now. but those contents does not displaying on the screen.
In this order I write the code. Please explain me
SELECT-OPTIONS s_date FOR likp-wadat_ist.
DATA BEGIN TYPE wadat_ist.
DATA LAST TYPE wadat_ist.
initialization.
s_date-low = BEGIN.
s_date-high = LAST.
at selection-screen output.
CALL FUNCTION 'HRWPC_BL_DATES_MONTH_INTERVAL'
EXPORTING
    datum                = SY-DATUM
    month_pst            = '0'
    month_ftr            =   '0'
IMPORTING
   BEGDA                = BEGIN
   ENDDA                =   LAST
EXCEPTIONS
INVALID_VALUES       = 1
OTHERS               = 2
IF sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
        WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.

How do I connect and detect a high frquency pulse (0-3500hz) with a variable pulse voltage (0v low,5-10v high), on a SC-2345 connected to a PCI-6224?

How do I connect and detect a high frquency pulse (0-3500hz) with a variable pulse voltage (0v low,5-10v high), on a SC-2345 connected to a PCI-6224? Labview doesn't generate a waveform if I try to graph the signal, and my analog input doesn'y recognize that the signal is even pulsing, only that it has a voltage. Some advice would be much appreciated.
Thanks in advance,
Garrett

Hi Garrett,
It sounds like you want to do Frequency Measurements of a signal that is somewhat digital.
There are two ways you can really do this:
Wire your signal to the counter input and use the Digital Frequency examples (Help > Find Examples > Browse > Hardware Input and Output > DAQmx > Counter Measurements > Digital Frequency)
Continue taking analog measurements and use some sort of logic to determine where you are getting rising and falling edges.
I would recommend doing method #1, but you must determine which one is the best for your system.
If you want to connect to the counter pins then you will find the
terminals located on the side of your SC-2345. If you don't need
to condition your signals then simply wire everything into the proper
pins for your counter (below).
Default NI-DAQmx Counter Terminals (Connector 0)
Terminal
Counter Context (Default)
Motion Encoder Context
Signal Name
37
CTR 0 SRC
CTR 0 A
PFI 8
3
CTR 0 GATE
CTR 0 Z
PFI 9
45
CTR 0 AUX
CTR 0 B
PFI 10
2
CTR 0 OUT
PFI 12
42
CTR 1 SRC
CTR 1 A
PFI 3
41
CTR 1 GATE
CTR 1 Z
PFI 4
46
CTR 1 AUX
CTR 1 B
PFI 11
40
CTR 1 OUT
PFI 13
Otis
Training and Certification
Product Support Engineer
National Instruments

Low priority and high priority queue

Hi
we have high priority and low priority queue's. Functionality wise i know that time critical messages will be sent through high priority queue's and low priority messages will be sent
through low priority queues. But like to know what technicality makes this separation of
low priority and high priority queue's ? The crus of the question is what technical setting(s)
makes the queue as high priority and what technical setting(s) makes the queue as low priority
queue.
Thanks
kumar

i Michal
I am talking abt queue prioritization on Integration eninge only.
I am good with queue prioritization and am able to successfully implement
the same. We are using only PI7.0.
My question is what is the technical difference between high priority
and low priority queues ? what technical setting makes it a high priority
queue and what technical setting makes a low priority queue ?
Your answer:
how the system reacts to new messages if almost all queues are already blocked
for some types of messages
My comment: what setting makes the system to behave like that ? what property
of that queue makes them to behave like that ?
Thanks
kumar

How to change the low quality to high quality in iPhone 5c?

Hi everyone, I need help about this uploading a video on Facebook. Here's the story, I uploaded a video last friday (april25,2014) and I have to choose what quality the video should be, and I chose the low quality (for low space *new on iphone*) but, i think I was wrong on choosing the low quality over high quality. I watched the video from my Camera Roll and it's on high quality, but on facebook it was a low quality video. Now, does anyone could help me to change it to high quality from low quality? Sorry for this stupidity question..

hI,
     Very thanks ,
        I did it what u said now. but those contents does not displaying on the screen.
In this order I write the code. Please explain me
SELECT-OPTIONS s_date FOR likp-wadat_ist.
DATA BEGIN TYPE wadat_ist.
DATA LAST TYPE wadat_ist.
initialization.
s_date-low = BEGIN.
s_date-high = LAST.
at selection-screen output.
CALL FUNCTION 'HRWPC_BL_DATES_MONTH_INTERVAL'
EXPORTING
    datum                = SY-DATUM
    month_pst            = '0'
    month_ftr            =   '0'
IMPORTING
   BEGDA                = BEGIN
   ENDDA                =   LAST
EXCEPTIONS
INVALID_VALUES       = 1
OTHERS               = 2
IF sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
        WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.

I'm getting a very low signal from my Blackbird interface. The fire wire connection is selected properly and track recording sliders set. However the recording level slider in the lower right corner is grayed out. How can I get better signal?

I'm getting a very low signal from my Blackbird interface. The fire wire connection is selected properly and track recording sliders set. However the recording level slider in the lower right corner is grayed out. How can I get better signal?

If it's slow on startup it would be extensions loading or LaunchDaemons starting up.
You should have a look in:
/Library/LaunchDaemons
/Library/Extensions
You can count out anything in your home folder and it shouldn't put anything in /System as that's reserved for Apple.

I can not access a website page to input data because security level to high. How do I lower security level?

''duplicate of https://support.mozilla.com/en-US/questions/903690''
This web site uses Javascript extensively for menu navigation options. If you don't see a drop-down menu at the bottom of the top banner, then you have your security settings currently set to High. You need to set the security settings to Medium which is sufficiently secure for this site.

Reload web page(s) and bypass the cache.
*Press and hold Shift and left-click the Reload button.
*Press "Ctrl + F5" or press "Ctrl + Shift + R" (Windows,Linux)
*Press "Cmd + Shift + R" (MAC)
Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
*Don't make any changes on the Safe mode start window.
*https://support.mozilla.com/kb/Safe+Mode

Permit traffic from Inside to Outside, but not Inside to medium security interface

Can someone just clarify the following. Assume ASA with interfaces as :
inside (100)   (private ip range 1)
guest (50)       (private ip range 2)
outside (0)      (internet)
Example requirement is host on inside has http access to host on outside, but it shouldn’t have http access to host on guest – or any future created interfaces (with security between 1-99).
What’s the best practice way to achieve this?

Hi,
The "security-level" alone is ok when you have a very simple setup.
I would suggest creating ACLs for each interface and use them to control the traffic rather than using the "security-level" alone for that.
If you want to control traffic from "inside" to any other interfaces (and its networks) I would suggest the following
Create and "object-group" containing all of the other network
Create an ACL for the "inside" interface
First block all traffic to other networks using the "object-group" created
After this allow all rest of the traffic
In the case where you need to allow some traffic to the other networks, insert the rule at the top of the ACL before the rule that blocks all traffic to other networks
For example a situation where you have interfaces and networks
WAN
LAN-1 = 10.10.10.0/24
LAN-2 = 10.10.20.0/24
DMZ = 192.168.10.0/24
GUEST = 192.168.100.0/24
You could block all traffic from "LAN-1" to any network other than those behind the "WAN" interface with the following configuration.
object-group network BLOCKED-NETWORKS
network-object 10.10.20.0 255.255.255.0
network-object 192.168.10.0 255.255.255.0
network-object 192.168.100.0 255.255.255.0
access-list LAN-1-IN remark Block Traffic to Other Local Networks
access-list LAN-1-IN deny ip any object-group BLOCKED-NETWORKS
access-list LAN-1-IN remark Allow All Other Traffic
access-list LAN-1-IN permit ip 10.10.10.0 255.255.255.0 any
This should work if your only need is to control the traffic of the interface "LAN-1". If you want to control each interfaces connections to the others then you could do minor additions
Have all your local networks configured under the "object-group"This way you can use the same "object-group" for each interface ACL
object-group network BLOCKED-NETWORKS
network-object 10.10.10.0 255.255.255.0
network-object 10.10.20.0 255.255.255.0
network-object 192.168.10.0 255.255.255.0
network-object 192.168.100.0 255.255.255.0
access-list LAN-1-IN remark Block Traffic to Other Local Networks
access-list LAN-1-IN deny ip any object-group BLOCKED-NETWORKS
access-list LAN-1-IN remark Allow All Other Traffic
access-list LAN-1-IN permit ip 10.10.10.0 255.255.255.0 any
access-list LAN-2-IN remark Block Traffic to Other Local Networks
access-list LAN-2-IN deny ip any object-group BLOCKED-NETWORKS
access-list LAN-2-IN remark Allow All Other Traffic
access-list LAN-2-IN permit ip 10.10.20.0 255.255.255.0 any
access-list DMZ-IN remark Block Traffic to Other Local Networks
access-list DMZ-IN deny ip any object-group BLOCKED-NETWORKS
access-list DMZ-IN remark Allow All Other Traffic
access-list DMZ-IN permit ip 192.168.10.0 255.255.255.0 any
access-list GUEST-IN remark Block Traffic to Other Local Networks
access-list GUEST-IN deny ip any object-group BLOCKED-NETWORKS
access-list GUEST-IN remark Allow All Other Traffic
access-list GUEST-IN permit ip 192.168.100.0 255.255.255.0 any
Then you could basically use the same type ACLs in each interface. (Though still separate ACLs for each interface) And as I said if you need to open something between local networks then insert the correct "permit" tule at the top of the ACL.
Hope this helps
- Jouni

Updating security interface

Hi,
I'm new to weblogic so sorry if I get the jargon wrong.
We've been using version 5, and have customised security realms, but now we're
moving to version 6.1 and I've been asked to implement/update the java interface
for this version.
Can anyone give me any tips on how to do this or point me towards the documentation
on this please?
Many thanks,
Ed.

http://e-docs.bea.com/wls/docs61/security/prog.html#1041025
thanks
kiran
"Edward Quick" <[email protected]> wrote in message
news:[email protected]..
>
Hi,
I'm new to weblogic so sorry if I get the jargon wrong.
We've been using version 5, and have customised security realms, but nowwe're
moving to version 6.1 and I've been asked to implement/update the javainterface
for this version.
Can anyone give me any tips on how to do this or point me towards thedocumentation
on this please?
Many thanks,
Ed.

Run a workflow with a low security role profile

Hello,
I created a workflow that is sending an email to the administrator when a certain action has to be done. To make sure this workflow has actually been running, I ended it with a step that update a two option field as 'Email sent'.
I would like to lock this field for users because I only want them to read it but not change its data. So I enabled security role.
The problem is that since I made that, the workflow cannot be run because users don't have the security role to change this field.
I found out while browsing thrgough the internet that I had to check 'Execute as the owner of the workflow', but this didn't help.
So does anyone has a response to my problem or another way to manage it? A solution that does not involve any code because I'm not working in IT at all, we're a small company and so I'm a salesman.
Thanks for your help.
Sylvain

Hi,
Create these 2 fields as non-searchable fields so users cannot search them. If the user does not need to change these fields, make the fields read-only on the form. There is no need to use security role profile and play with
security roles for this.
Hope this helps.
Minal Dahiya
blog : http://minaldahiya.blogspot.com.au/
If this post answers your question, please click "Mark As Answer" on the post and "Vote as Helpful"

Roboform Vista (osana Avast Easypass'ia) ei lataudu, tulee virheilmoitus failed to lower security, error 0x80070005), mitä tehdä?

Avast Easypass ei toimi, oletettavasti koska roboformin osuus ohjelmasta puuttuu.

Ehkä yrittää asentaa Avast EasyPass? Näyttää siltä tiedosto voidaan määrittänyt väärin: [http://www.wiki-errors.com/wiki-errors.php?wiki=0x80070005
Katso myös Robo Kunto FAQ [http://www.roboform.com/support/faq # faq_firefox]

Low-Level or High-Level for GUI ?

I am developing a MIDLet that has to run CLDC-1.1 MIDP-2.0 Devices. The MIDLet has a simple user interface, and there is no gaming. I developed the MIDLet using the high-level GUI class, but I discovered that this class is nice, yet limited. Now I am investigating using the low level canvas class for the GUI. Is it possible to maintain cross-platform compatibility with the canvas, or should I stick with the high-level class?

High Level Group
Classes provided are
     Perfect for development of MIDlets that target the maximum number of devices
     Heavily abstracted to provide minimal control over their look and feel
     Classes do not provide exact control over their display
Low Level Group
Classes provided are
     Perfect for MIDlets where we want precise control over the location and display of the UI elements
     If more control there is comes less portability It may not be deployable on certain devices
Cheers,
Rohan Chandane

Lower security to higher security interface PAT.

Similar Messages

Maybe you are looking for