LTE in Germany using Telekom/Vodafone LAN-to-LAN tunnel

Hello !
We habe some locations with very slow DSL connetion (< 200 kbit). Some services need direct vpn-connection to the datacenter and some RDP access etc. - the networks are connceted with LAN-to-LAN ipsec tunnel. Work's fine with slow speed.
Now we like to set up one side with LTE. Did someone set up ipsec with one side via LTE via Telekom or Vodafone in Germany ?      

PIN:
router#cellular 0/2/0 gsm sim unlock 6543
Create the profile:
router#cellular 0/2/0 gsm profile create 1 apnname.net
AT command is
ATD*gprs_sc*CID#                                               
or
ATDT*gprs_sc*CID#                                 
where gprs_sc (GPRS service code) is 99, but  98 can also work. T-Mobile says 99, Cisco docs contain 98.
                  Some modem manual says:
                 99 (GPRS Service Code) a digit string (value 99) that identifies a
                   request to use the Packet Domain service.
                  98 (GPRS Service Code) a digit string (value 98) that identifies a
                   request to use the IP service
CID (PDP Context Identifier) is the connection profile number (see show cellular 0/2/0 profile ), number between 1..16 This profile contains the APN name.
Typical AT command is: ATD*99*1#*
(Or simply *99# ,  default CID is obviously 1 )
I don't think you need a chat-script:
interface Cellular0/1/0
  no ip address
  encapsulation ppp
  load-interval 30
  dialer in-band
  dialer pool-member 1
  dialer-group 1
  async mode interactive
interface Dialer0
ip address negotiated,
no ip redirects
  no ip proxy-arp
  encapsulation ppp
  load-interval 30
  dialer pool 1
  dialer idle-timeout 0
  dialer string "*99*1#"
dialer persistent
dialer-group 1
  no cdp enable
  ppp pfc local forbid
  ppp pfc remote reject
  ppp acfc local forbid
  ppp acfc remote reject
  ppp eap refuse
  ppp eap local
  ppp chap refuse
  ppp ms-chap refuse
  ppp ms-chap-v2 refuse
  ppp pap refuse
  ppp ipcp address accept
dialer-list 1 protocol ip permit
Troubleshooting:
sh int cell0/0/0
sh cell 0/0/0 all
(config)#service internal
(config)#exit
#test cellular 0/0/0 modem-power-cycle

Similar Messages

  • Can I access English movies and TV, living in Germany using the Apple TV

    Can I access English movies and TV, living in Germany using the Apple TV or maybe something else?
    I live since short in Germany and would like to have access to English TV and English movies using my internet connection. Looking at for example the Apple Store your store connection is based on your IP {address and this lands me in the German store where movies are not available in original language (or so it seems, if you do not know this the Germans change the soundtracks of all foreign movies to German by dubbing).
    Does anybody know how I would be able to watch either UK or USA TV over the internet (preferable on my TV)?
    I say thank you and yes in case you did not guess, I am new to the topic of TV over internet.

    thanks Jolly Giant
    however, there are somewhat limited options such as [_*Kabel Digital*_|http://www.kabeldeutschland.de/fernsehen/kabel-digital-international/englisch.ht ml].
    I looked in to that and they are non of the channels I want to see. Most of it is stuff you catch free to air.
    additionally, many movies, tv shows and sport broadcasts on [_*Sky Deutschland*_|http://www.sky.de/web/cms/de/abonnieren-senderinfos.jsp] come in [Zweikanalton|http://en.wikipedia.org/wiki/Zweikanalton].
    I talked to the Sky folk in Germany a while ago, and sorry to say they are as knowledgeable as the Sky UK people. In other words nobody could guarantee me anything or commit to it beingavailable in English. The most committed answer I got was that it depends on many things and one would have to look at each broadcast to see if it is also available in English.
    Hence my search continues.

  • I recently upgraded to mac os x lion. But now my broadband pen doesn't work. I'm portuguese and i use the vodafone network. Can anybody help me?

    Hello.
    My name is Margarido and i'm portuguese. I use a mobile operator named zon to access the web using a broadband pen modem.
    This operator uses the vodafone technical support (network) and since i upgraded to the Mac OS X Lion, the pen modem doesn´t work.
    Can anybody help me?
    I eared that Mac OS X Lion doesn´t support pen modems yet. Is this true?
    Thank you.

    Your best bet is to call the Vodafone technical support helpline. Since each manufacturer writes custom software for each OS. They might be working on new drivers...

  • I have a iphone 5 and just updated to ios 8 now i have extended lte where it use to say verizon lte

    i have a iphone 5 and just updated to ios 8 now i have extended lte where it use to say verizon lte

    This is being discussed in more detail, but without a solution, in another thread: https://community.verizonwireless.com/thread/840295?tstart=0
    I am having the same problem with my new iPhone 5s since I installed the current software 8.1.2 yesterday after activating the phone at a Verizon store in Tucson, AZ. My zip code is 84745.
    So far I have no battery problems, but that's probably because I have cellular off except when I need it. I am usually on WiFi at home/work as my old 4s was one of the phones that, after an earlier software upgrade, chewed data up for no reason.

  • Can I use a Vodafone USB Dongle with my apple IPad 1st Generation if I have a USB adaptor for my IPad

    Hi there just wondering does anyone know if I can use a Vodafone USB Dongle with my apple IPad 1st Generation 16gb (WiFi only) if I have a USB adaptor, will the IPad !st generation support a A Vodafone Dongle(Irish network)

    You cannot plug a USB dongle into an iPad using the USB part of the iPad Camera Connection Kit.
    The Camera Connection Kit is for connecting cameras - hence the name.
    You'd need to get a MiFi device to use 3G data via WiFo on your iPad.

  • HT204380 I have done all the above. I am in Germany using an iPad 2, trying to call an iPad 2 in the UK. My IPad goes through the call and then times out. I have been on the phone to the receiver at the time so know they had their iPad on.

    I have done all the above. I am in Germany using an iPad 2, trying to call an iPad 2 in the UK. My IPad goes through the call and then times out. I have been on the phone to the receiver at the time so know they had their iPad on.

    What do you mean that you can't "call" an iPad in the UK??  That doesn't particularly make sense.  You can email to an iPad or text them, but the iPad is not a phone, so how do you expect to "call" them??
    Hope this helps

  • My mac pro (SL 10.6.8) wakes up every minutes when I use wake on lan and share a HD. when I unplug the ethernet it doesn't wake so I suppose that some thing wakes it up on my network ( 2 mac books, 2 iPads and 2 time capsules !) How can I fix that?

    Hy ,
    My mac pro (SL 10.6.8) wakes up every minutes when I use wake on lan and I share one of my Hard Drive.
    When I unplug the ethernet cable it doesn't wake any more so I suppose that some thing wakes it up on my network ( 1 printer canon MP620, 2 mac books, 2 iPads, 2 IPhones and 2 time capsules !) ...even when all these devices are "sleeping" 
    Any idea?
    THKS
    Phil
    PS .: I'm french so my english is probably quite strange ! ... Sorry for that

    Sorry - posted this in the wrong forum. Reposted in Mac Pro.

  • I bought iPhone in Italy. There is wrote: Contient use se Vodafone. Will it work in Russia? May be I need to do something?

    I bought iPhone in Italy. There is wrote: Contient use se Vodafone. Will it work in Russia? May be I need to do something?

    I got my real add-on work on FF4 now. Here is what needs to do (on VS2005)
    In project property<br>
    C++<br>
    General/Additional Include Directories - xulrunner-2.0.en-US.win32.sdk\xulrunner-sdk\include<br>
    Preprocessor/Preprocessor Definitions - MOZ_NO_MOZALLOC;XP_WIN;XP_WIN32
    Linker<br>
    General/Additional Library Directories - xulrunner-2.0.en-US.win32.sdk\xulrunner-sdk\lib<br>
    Input/Additonal Dependencies- nspr4.lib xpcom.lib xpcomglue_s_nomozalloc.lib
    Update module cpp by following the sample<br>
    http://mxr.mozilla.org/mozilla-central/source/xpcom/sample/nsSampleModule.cpp
    Add two extra directives on chrome.manifest<br>
    interfaces &lt;path/to/your/xpt&gt;<br>
    binary-component &lt;path/to/your/dll&gt;
    Add unpack property to install.rdf if needed
    https://developer.mozilla.org/en/Install_Manifests#unpack

  • Is it possibel to use an vodafon sim card in an iphone 2?

    is it possibel to use an vodafon sim card in an iphone 2?

    Only the carrier an iPhone is locked to can authorize the phone's official unlocking. If you want the phone officially unlocked, you'll have to contact the carrier it's locked to to see if they offer unlocking & what the procedure is.

  • Use client VPN tunnel to traverse LAN-to-LAN tunnel

    I've been troubleshooting a problem and can't get over a hurdle. The ASA is running ASA running 7.2(1)24 code. I'm trying to use a client VPN tunnel to connect to the ASA. The ASA already has a LAN-to-LAN tunnel set up and functioning, and I need the client VPN to access the remote site over the LAN-to-LAN tunnel.
    The internal IP address of the local side is 192.168.0.0/24 and the IP of the remote LAN-to-LAN tunnel is 172.20.1.0/24. The clients are handed out 192.168.200.0/24 IPs. I've attached the relevant configuration for the ASA.
    When the client VPNs into the network, I can access the resources on the ASA's internal network. Users on the ASA's internal network can access resources across the LAN-to-LAN tunnel. Client VPNs cannot access resources over the LAN-to-LAN tunnel. For the latter, there are no hits on the C-TEST access list.
    Thank you for your assistance.

    try adding...
    same-security-traffic permit intra-interface
    http://www.cisco.com/en/US/products/ps6120/products_configuration_guide_chapter09186a00806370f2.html#wp1042114

  • Does ipad mini 2 wifi only can access to LTE signal by using pocket wifi 4g lte?

    Does ipad mini 2  WIFI ONLY can access to LTE signal by using  pocket wifi 4g LTE.,THANKS

    Hello Aaryn D
    You should be able to connect to that hotspot without issue as an iPad will see it within the Wi-Fi networks and you would not need the cellular model unless you want the iPad to constantly have a data connection.
    iOS: Connecting to Wi-Fi
    http://support.apple.com/kb/HT5569
    Regards,
    -Norm G.  

  • IPad air and LTE in Germany with O2

    When can you expect that with the Ipad air and the Mini retina can be used also LTE by O2 in Germany
    The frequency bands of the Ipdas are identical to those of the IPhone 5S - why is the function at O2 still not teleased?
    Sice already the TouchID when the IPad was saved and do not exist, the lack of LTE keep coverage now but certainly me from a purchase.
    Do you hav Information about LTE with O2 on Ipad Air and IPad mini Retina? O2 certainly has none.

    This will probably come in handy for you.
    http://help.apple.com/ipad/7/#/
    Your questions are sort of all over the place and it makes it difficult to offer help when you splatter a whole bunch of stuff against the wall at once.
    Mail accounts will sync to the iPad from iTunes if they are selected to sync. You can add the email account to the iPad in Settings>Mail, contacts, calendar>Add account. If you restore the iPad from a backup of another iPad, that should restore the email accounts to the new iPad.
    Your backups will always be separate because iTunes reads the serial number on the iPad so if you had 10 iPads and gave them all the same name, iTunes would still see each one as it's own device.
    You also threw the iPhone into the mix now. Why don't you start over and explain what you did to set up the new iPad Air. Or just start over and clarify all of the information a bit.

  • Satellite C660 - how to enable and Use WAKE ON LAN?

    Hi All,
    I previously posted asking about using Wake on Wireless LAN and was very helpfully advised that this was not possible, so I have started to explore the Wake ON LAN option.
    I have a Toshiba C660 PSC0LE-00500JEN and have enabled Wake ON LAN on the BIOS, and have connected a LAN cable between my wireless router and the laptop, both of which recognise each other so the cable seems ok.
    However, whether I use a WAKE ON LAN app on my android, or I use an online "wake on lan via browser" site, the laptop still remains asleep.
    Can anyone advise?
    Thanks
    James

    Hi
    The Wake Up on Lan option would work if you would send an Magic Packet to the remote machine (notebook).
    I have no experience using the Android app who knows if it function properly
    Try other method. For example using an software like Wake on Lan for Windows Graphical User Interface (GUI)
    Google for that to download this software.
    Furthermore go to device manager -> LAN card -> Properties -> Advanced tab and check here if the WOL is enabled too

  • Configuration of AirPort Extreme Using Third Party LAN Ethernet Adapter?

    Hello;
    I am trying to set up my own wireless connection, not without great consternation. Any help would be greatly appreciated. Here is my current situation:
    Subscribed to DSL service - installation went well, and it works fine on two other computers (that are not wireless). Installed same in computer that will use airport extreme, and it shows a connection, but won't load the browser pages.
    Airport Extreme Base Station is working, software installed, etc., but computer doesn't offer airport as a connection choice in system preferences, internet connect, Airport set-up assistant, etc. (because there's no airport card installed????). Consequently, I can't finish w/airport set-up assistant.
    I'm using a third party LAN ethernet wireless adapter since I was told airport cards for my G-4 are no longer made. Adapter and software installed, and shown to be working.
    What am I missing?
    Thanks
    KAS
    PowerMac G-4   Mac OS X (10.3.9)  
    PowerMac G-4   Mac OS X (10.3.9)  

    Hello Duane
    Thank you for your warm welcome and quick response. I will try the AirPort Admin Utility. Your help is greatly appreciated!
    -K
    PowerMac G-4   Mac OS X (10.3.9)  

  • The end of guest networks in Germany using Telkom speedport W921?

    Just a note worth thinking about.
    I am amazed at how little attention is given to above subject and the lack of clear answers in this forum and elsewhere. It seems the new generation of VDSL speedports no longer support Time Capsule/airport to implement guest networks, if the user is not ready to give up on IP based telephony or land line telephony for that matter. The current system of anlalog and isdn telephony will be phased out by Telekom in the mid term, which means that no telephony with current land line numbers will be possible, if the speedport is relegated to a pure modem, which for now worked fine, when configuring the TC as the router with guest net work capability. Using the proposed fast internet via the speedport W 921v only alows the TC to be used in bridge mode, which excludes the implementation of an isolated guest network.
    Flatly put you can either use the high speed internet with all features except guest network by airport and TC, or you have to abstain from land line telephony using your know telekom numbers. This hypothesis is for German users only.
    Any workable solutions to this problem would be higly appreciated. And maybe Apple should address this problem in the architecture of airports and TC's as well.

    Any workable solutions to this problem would be higly appreciated. And maybe Apple should address this problem in the architecture of airports and TC's as well.
    The restriction is purely Apple..
    I have an Asus RT-AC66U and it has no problem creating up to 6 different networks apart from the main network. It makes no difference of what mode it is running. Each of those networks can have their own individual settings including isolation or not. This is using almost the same hardware as the latest AC version Airport. So the answer is obvious.. relegate your apple router to its best function.. an AP.. and buy a router.. a real one.

Maybe you are looking for

  • ExtensionHarxdening in 2013

    Hi, i prepared an excel sheet using cakePHP frame work with 'application/vnd.ms-excel' mime type.when i am trying to open it in excel 2013 it prompt like The file format and extension of 'filename.xls' don't match. The file could be corrupted or unsa

  • Holder name not comming in ORG model

    Hi Experts, When i am assigning Holder to a position ,in the basic data am not getting the name.Instead of the name of BP am getting some number which is not the BP ID too in the basic data tab. Please provide your ideas to overcome this issue. Thank

  • Transfer of Asset from one class to another

    Hi Friends, one asset has been created using wrong asset class. We haven't passed any dep run entries at all. I created another asset in correct asset class and tried to use ABUMN. Under Transfer: to existing asset - it does not allow me: error : ret

  • I am getting the ! icon when I turn on ipod.

    I am getting the !icon with the folder when my ipod freezes and I try to reset it. I have tried all the suggestions on the article on the support page but nothing is working for me. Eventually my ipod will turn on again and seems to be acting normal.

  • Issues with Jpegs on Mac os

    I'm trying t take images directly from the cf card on a canon camera to an imac. I can view the images as thumbnails in Finder but if i double click on them i get a message that they are truncated or damaged - do i wish to continue. If i click yes an