MacBook Air will not print on wireless Epson printer.  It says 'filter failed'

MacBook Air all of a sudden will not print on wireless Epson printer.  The error message is 'filter failed'.  Shut down everything and rebooted, but still not printing.

Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
Select
          /var/log ▹ cups ▹ error_log
from the hierarchical list on the left side of the Console window. If you don't see that list, select
          View ▹ Show Log List
from the menu bar.
Each message in the log begins with the date and time when it was entered. Select the messages from the time of the last failed printing attempt. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message (command-V).
If there are runs of repeated messages, post only one example of each. Don’t post many repetitions of the same message.
☞ The log contains a vast amount of information, almost all of it useless for solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.

Similar Messages

  • Macbook Air will not find network wireless printer, ipad   PC print ok

    Deskjet 3055a printer on wireless connection to Virgin Superhub.
    ipad and a PC print ok.
    I cannot add MacBook Air (in same room) to the Network.
    Please help.

    Hi Dagnabit47,
    Welcome to Apple Support Communities.
    It sounds like there is an issue adding a wireless printer on your MacBook Air. The article linked below will walk you through the process of adding the printer and ensure the MacBook Air setup correctly.
    OS X Mavericks: Set up a printer
    http://support.apple.com/kb/PH14143
    Add a Wi-Fi printer
    Follow the instructions that came with the printer to connect it to your Wi-Fi network and turn it on. Use the instructions to unpack the printer, install ink or toner, and add paper. For more information, see this article:
    Apple Support article: Connecting a Wi-Fi printer to your Wi-Fi network
    Choose Apple menu > Software Update to make sure OS X has the latest information about printer software it can download from Apple. If Software Update doesn’t list an update for your printer, you have the latest software.
    Open a document to print, then choose File > Print.
    Open the Printer pop-up menu and choose your printer in the Nearby Printers section of the menu. If you don’t see your printer, choose Add Printer from the Printer pop-up menu.
    A dialog appears listing printers on your local network. It may take a minute or two for your printer to appear.
    If you’re asked for an administrator name and password
    Select your printer when it appears in the list, and then click Add. OS X automatically uses AirPrint if your printer supports it, or it selects printer software (also called a printer driver) and downloads it from Apple if necessary.
    I hope this helps.
    -Jason

  • My Macbook Air will not print wirelessly!

    My Macbook Air will not print wirelessly using the connection between it and my iMac which is connected via USB to my Canon Printer. The iMac and the Air are both using the same network and the printer is found on the Air... it sits at idle, but when I press "Print" on my Air it never actually prints. There is just a flash of the print icon on the Dock and then it is gone... I am left with no reason or error message. My colleagues are able to print wirelessly with no issue using their Macbook Pro and the same connected iMac. Can anyone help with this?
    Macbook Air: OS X 10.8.3
    iMac: OS X 10.7.5
    Canon Printer: ImageClass MF4370dn

    Hi JDP86,
    Thanks for using Apple Support Communities.
    If your printer is wireless-capable, you should first add the printer to your network. Use the printer's control panel, or temporarily connect the printer to your Mac via USB.
    Use this article to troubleshoot printer issues in OS X.
    Troubleshooting printer issues in OS X
    http://support.apple.com/kb/ts3147
    Best of luck,
    Mario

  • Macbook air will not connect to the wifi network

    I recently had to replace my wireless network router and now my macbook air will not connect to the network. it worked fine with the old wireless router. Now, i get a "unable to join wi-fi network" message. The network ID (SSID) and password (WPA) are the same as before. I try to manually enter the password, but continue to get the previous message.
    Any help in figuring out how to correct this problem is greatly appreciated.
    Also, I have several PCs in the house that have had zero problems connecting to my wireless with the new router. What am I doing wrong?

    Hi,
    Ever since did the last airport utility update this has been happening.
    I believe the airport utility update is solely a software update. Repair permission and repair disk (boot from your installation disk A) may help.
    Other wise, http://osxdaily.com/2009/12/22/mac-wireless-problems-guide-to-troubleshooting-ai rport-wireless-problems-on-your-mac/ may help, too.
    Cheers.

  • My MacBook Air will not turn on. I get a white screen with the apple logo and a spinning star that just does that for hours

    My MacBook Air will not turn on. I get a white screen with the apple logo and a spinning star (search icon). It will spin for hours and never go away unless I power off.

    Take each of these steps that you haven't already tried. Stop when the problem is resolved.
    To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
    Step 1
    The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
    There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
    a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
    b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
    c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
    d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
    Step 2
    If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
    Step 3
    Sometimes a startup failure can be resolved by resetting the NVRAM.
    Step 4
    If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
    Step 5
    If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
    Step 6
    Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
    Step 7
    If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
    Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
    Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
    If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
    If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
    Step 8
    Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
    This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
    Step 9
    If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.  
    Step 10
    Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
    Step 11
    Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
    Step 12
    This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
    Step 13
    If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

  • My macbook air will not connect to the internet due to a self assigned IP address. I have tried trawling the support forums, but either I can't understand the suggestions, or they don't work. Please explain to me in simplest terms how to fix this. Thanks!

    My macbook air will not connect to the internet due to a self assigned IP address. I have tried trawling the support forums for hours, but either I can't understand the suggestions, or they don't work. Please explain to me in simplest terms how I can fix this. Many thanks!

    The warranty entitles you to complimentary phone support for the first 90 days of ownership.
    If you bought the product in the U.S. directly from Apple (not from a reseller), you have 14 days from the date of delivery in which to exchange or return it for a refund. In other countries, the return policy may be different. If you bought from a reseller, its return policy applies.

  • My Mac Mail subfolders on my MacBook Air will not sync in alphabetical order. I am assuming it is a setting that I am not finding since my iMac based at my home office is fine, so is my iPad and iPhone. The core source is Exchange.

    My Mac Mail subfolders on my MacBook Air will not sync in alphabetical order. I am assuming it is a setting that I am not finding since my iMac based at my home office is fine, so is my iPad and iPhone. The core source is Exchange.

    If you have been using the mac.com Apple ID to make iTunes purchases recently, then there should be no issues continuing to use it with the new iPhone. I would abandon the new ID as you will never get Apple to merge the two IDs. I have had a mac.com ID for years and continue to use it with my iPhone 4S.
    Tell us the issues that you encounter trying to set up the iPhone with the mac.com account.

  • MacBook Air will not reboot. A file folder with a question mark in the center of it appears. What is the problem?

    MacBook Air will not power on or reboot. A file folder with a question mark in the center of it appears. What is the problem?

    Go step by step and test.
    http://support.apple.com/kb/ts1440
    Startup Manager to select Startup disk.
    http://support.apple.com/kb/HT1310
    Repair Disk
    Steps 2 through 8
    http://support.apple.com/kb/PH5836
    Reset PRAM.
    http://support.apple.com/kb/PH4405
    Reinstall OS X
    If this does not help, contact Apple.
    Best.

  • IMessage on my macbook air will not connect.

    iMessage on my macbook air will not connect. It says "Could not sign in. Please check your network connection and try again." I have gone through all the support instructions and a lot of these discussion chats. I have sign out of it and my phone and resigned in. I have checked that everything is verified and connected. My ios is up to date on both my computer and phone. It worked fine until about a week ago and suddenly it stopped
    Thank you for your assistance!

    Hi,
    In Hard Drive/Library/Fonts  do you have the AppleGothic.ttf  Font.
    The iMessages account uses this to "register".
    If the computer has been Off then the App effectively "registers" the Apple ID again.
    It cannot do this is the Font is "missing".
    The thread I saw that highlighted this as an  issues said the font could be downloaded from Apple  but not the "how" of that.
    8:08 pm      Wednesday; July 16, 2014
    ​  iMac 2.5Ghz i5 2011 (Mavericks 10.9)
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro 2Gb (Snow Leopard 10.6.8)
     Mac OS X (10.6.8),
     Couple of iPhones and an iPad

  • HT5730 my trackpad and keyboard on my macbook air will not connect.. how can i fix this without having to drive 2 hours to an apple store.

    my trackpad and keyboard on my macbook air will not connect.. how can i fix this without having to drive 2 hours to an apple store

    i also have an external mouse and keyboard hooked up to it.. future shop suggested resetting the macbook. but i cant figure out how to do that.

  • My macbook air will not boot

    My Macbook Air will not boot.  It starts and hangs up at the apple logo.  Is there a bypass to see what the problem is?

    Try a Safe Boot by holding down the Shift key between the startup tone and the Apple Logo.  This will take longer than a normal boot and display a progress indicator.  If successful, Go to System Preferences > Startup disks > select your Boot drive and restart.  
    Regards,
    Captfred

  • My Macbook Air will not play music from the speakers

    My Macbook Air will not play music from the speakers and the institutions says that it can only play sound out of earphones.

    Is your account authorised on your Mac's iTunes ? If not then you can authorise it via the Store > Authorise This Computer menu option.
    If you are being repeatedly asked to authorise the account : iTunes repeatedly prompts to authorize computer to play iTunes Store purchases - Apple Support

  • My macbook air will not shut down or restart

    my macbook air will not shut down or restart, but it will go to sleep. what can i do to fix this ?

    correction its a macbook pro

  • My macbook air will not turn on and it has been charging all night? What to do?

    My Macbook Air will not turn on this morning after charging all night, what can I do to start it?

    Check the adapter >  Apple Portables: Troubleshooting MagSafe adapters
    And try a different electrical outlet.

  • Macbook Air will not connect to the internet via Wi-Fi or Ethernet

    Macbook Air will not connect to the internet via Wi-Fi or Ethernet? Any ideas why not and how to fix this problem?

    Power down the router. Unplug the cord from the wall. Wait a while.
    Plug the cord back in. Restart the router.
    Wait until all the lights are lit up properly.
    Restart the computer.
    Best.

Maybe you are looking for

  • CC 2014.1 Media Loading Forever

    I have a project that was functioning properly in CC 2014. I updated to 2014.1 and now premiere gets stuck in loading media and won't finish loading it, so most of the media is listed as pending. I have figured out that it is getting stuck on After E

  • ACH Edi  error report

    I am currently working on setting up ACH process for a client using the SAP's standard IDOC process. Once the bank receives the ACH Idoc, if there any errors such as vendor account number missing, they send an edi error file back. Client is asking if

  • Lost songs, can't restore, recovery mode loop?

    I plugged in my ipod nano for just a routine synch of some new songs.  All appeared to synch as normal, but then I looked and it said "0 songs!!!"   Next, an error message pops up and gives me no choice but to restore to factory settings, or cancel,

  • Failed back-up attempts

    Ok whenever I sync my iPod, when it does the "backing up," it'll finish the back up but then it says that iTunes has stopped working. It does this on my laptop AND my PC with both my iPod and iPad. What do I do about this?

  • Adobe Premiere Elements 9 constant crashing

    Hello, I was wondering if anyone was experiencing this problem, every time I try to move video around the timeline in Premiere Elements 9 (PE9) it develops an error and I get the box that gives me an option to send a report to Microsoft. I have tried