Macbook Pro  SSD SATA III - Worth it?

Hello everyone
I own a mid-2010 13 inch MacBook Pro (2.4 Core 2 Duo). Since i cannot afford a new mac, i want to speed it up a little bit.
The first thing i did was to upgrade the memory to 8GB (from Crucial). The next thing i would like to do, is replace the hard disk with
an SSD one. I have checked many SSD's and i ended up between Crucial and OWC (128GB versions).
I can afford the cost of an SSD but i just realized that these drives are SATA 3. While, if i am not mistaken, my macbook
supports SATA 2 as maximum speed. Is it worth to buy a 6GB/s SSD afterall or not?
I would really appreciate your help and experience.
Thanks
Dimitris

You're correct, they are SATA II, which is limited to 3Gb/s, so it's not worth it to get the faster solid state. Still, though, even at 3Gb/s, you're going to see a giant performance boost over your current hard disk. Enjoy your solid state!

Similar Messages

  • Macbook Pro 2011 SATA III support

    I would like to know if the new Macbook Pro 2011 supports SATA III SSD's. I know the thunderbolt needs the Sandy Bridge to work, however I am not sure if that means that the chip will definitely support a SATA III SSD. Does anyone know ????

    Eww,
    Thank you very much or your response. I have a clarifying question. I am looking at buy a OCZ VERTEX 3 SATA III 2.5" SSD and I just want to be sure that if I spend the money on it I am going to get 100% functionality to include the 6/Gbps, minus of course the TRIM feature because from what I understand Apple locked it out. Do you know if this drive will work on the 2011 MacBook Pro.

  • Does the Mac Pro Support SATA III?

    Hi everyone, I've been wondering for a long time: Does the late 2012 12-Core Mac Pro support SATA III 6Gb connection? If not, is there any way of making it SATA III?

    Most commercially-available rotating drives cannot possibly source data off the platters at higher than a momentary bursts of up to 125MBytes/sec, or about 1.0Gbits/sec. That means SATA-I speed is not a bottleneck.
    A few drives are faster, and some SSD drives are faster.
    Many drives available today are capable of transfers at up to 6Gbits/sec.They will operate correctly at the Mac Pro's 3Gbits sec Bus speed. But since they cannot produce data from the drive platters at those speeds, you get at most a tiny, momentary burst at that speed.
    6Gbits/sec is far higher than other bottlenecks in the drive. There is no point in paying extra for this spec, as the drive cannot achieve it steady-state, and it provides no measurable advantage. I refer to such practices as "specsmanship". Feel free to read "cr@p".

  • Big Problems with Samsung Series 830 SSD SATA III (256GB) and W520

    Hi,
    i get my W520 last week with an normal SATA 500 GB Drive, at home i changed it to a Samsung Series 830 SSD SATA III (256GB) and install windows 7 64bit pro via recovery media.
    I was wondering, startup was taking very long .... from starting windows to the logon screen 1.45 minutes ... Now i tried a new recovery, same issue, tested the harddisk which is in good state.
    I changed back to the 500GB Drive, startup take only 30 seconds around....
    Are there any known issues?
    Best Wishes
    Markus
    Solved!
    Go to Solution.

    Hi,
    hope to catch all questions and some additional Information 
    1. RST is installed
    2. BIOS 1.34
    3. latest Lenovo Updates are all installed
    4. latest Windows Updates are all installed
    5. Clean Install i have tried, but first startup has shown the same issue
    6. Tried the SSD via main bay and via multibay
    7. checked BIOS for AHCI Mode
    8. switched to Diagnostic mode (where can i view the report, machine goes driectly further in Booting windows)?
    Machine Type is 42844MG
    Core i7-2860QM (2.50GHz), 16GB RAM, 500GB 7200rpm HD, 15.6in FullHD LED BL 1920x1080 + Colorimeter, 2GB nVidia Quadro 2000M, CDRW/DVDRW, Intel 6300AGN Wireless, Modem, Bluetooth, UMTS, 1GB Ethernet, UltraNav, Secure chip, Fingerprint reader, Kamera, 9c Li-Ion, Windows 7 Professional (64-Bit)
    What speaks again Samsung SSD's, at the moment it is the fastest SDD on the market and so far i've seen no bad rewiews.
    I can't find any thread with same (SSD and problem) ... i have seen some SSD issues in another community thread, but not with same symtoms. I don't know where to locate, at the SSD, at W520, whereeever.
    Best Wishes
    Markus

  • Compatibility ssd sata III and macbook pro 13 december 2009

    Hello I have a macbook pro 13 that I bouhgt in December 2009 i wanted to know what SSD is compatible, is sata III ok?

    Either a sata II or III drive will be compatible with  your MBP 2009.

  • MBP 5,5 supports OWC Pro 6G SSD SATA III?

    My MBP 5,5 (bought it in 2009) hard drive got failure so I ordered a OWC SSD Pro 6G for replacement. I have it installed but it can't be recognized during the OS installation, and even does not show up under the Disk Utility.
    However, if I put this SSD as external hard drive via USB, it works perfectly, so my answer is - does my MBP supports this SSD?
    Thank you

    You got a SATA II bus, but for some reason, you are only connecting at 1.5Gb/s. Try resetting your SMC and PRAM.
       Resetting the System Management Controller  >>
    17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
    Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101

  • Macbook early 2011 supports ssd sata III?

    Hello, i have a macbook early 2011, I wonder if it supports SATA III ssd, if i remember your original hdd is sata II .. serial number: C1*******RJ7
    Thanks
    <Edited by Host>

    Yes it will.

  • New Macbook Pros: SSD's upgraded to SATA rev3.0?

    I have searched  tech specs all over Apple's site; I cannot find a thing about the SSD's of the new MacBook Pros. In some of the 2011 releases,  SATA 3.0 connections started appearing—even though their drives were not 6Gbit/s per se. Does anyone know if they've progressed to faster SSD's? 

    Since this post I've checked the retina display notebooks at my local Apple store, and discovered that they are equipped with 6 Gb/s solid states. Also, all of the new MacBook Air SSDs are 6 Gb/s link-speed.

  • Can I use SSD SATA III to SATA II macbook white 5.2?

    hi all
    I have macbook white 5.2
    use technology HDD SATA2
    I want to put SSD SATA 3, and combine HDD Drive.
    Can I put SSD SATA 3 to SATA 2 HHD. and HDD I wan to put place DVD drive?
    please share experience :) or mayne have knowledge. about it
    thank you :)

    lots of suggestions and advice
    Drive Upgrade DB @ www.xlr8yourmac.com, Barefeats, MacGurus, OWC.

  • Is a MacBook Pro w/ Retina display worth the price?

    Apple community-
        Looking at purchasing portability for school- going to work on an MFA in graphics/web/new media, and need some assistance.  I've an iMac from 2007, seems to run flawlessly, but looking at options for taking school with me while at work- I'm currently travelling five different states in my current position.  The new MacBook Pro with Retina display looks stunning, albeit expensive, but has many features that worry me.
        For instance, everything is completely bolted/soldered/non-upgradeable, so any desire of modification needs to be purchased pre-production, right?  Also, the big issue with their PCIe "Flash based" storage... exactly what is this, and why is it so freaking expensive?  I've read different reports on Apple using various manufacturers, so not every MacBook as the same storage model, no third party attempts at upgrades, etc..  If I'd like to install numerous, monstrous programs, such as the entire Adobe Creative Suites, 3D Max, Maya, Final Cut, and so forth, I'll need a high capacity memory drive, as I assume most, if not all of these, need a root drive to install, and not simply an external hard drive.  I still make CDs/DVDs, so a SuperDrive is another $80.
        Chatting with an Apple representative, she stated that there is "only one model that will run my software at peak performance," which was the 15-inch model, starting at $2k; also, my software needed a "dedicated graphics card,"  I'm not too certain that it needs all that, and a high-end PC laptop could certainly run all of my demands- but let's face it, this is an Apple discussions community, and I'm plain simply accustomed to working on an Apple computer.  Plus, I don't really care for Windows 8.
        Should I possibly aim to purchase an older model used, something without Retina, but with more storage?  Is Retina that big of a deal for a laptop?  I also considered the possibility of just toting a Mac Mini with a 13-inch Cintiq tablet; though it does need a constant power supply, it's still quite portable.
        Thoughts?  Am I just overthinking this?  I've been expecting a MacBook to be expensive, but this could be pushing it a bit.
    Cheers!

    guiparent,
    whether it’s worth the price or not is an entirely subjective opinion. My own choice was to buy a used non-Retina 13-inch Mid 2010 MacBook Pro, and replace its hard drive with a SSD; but since I don’t use graphic-intensive apps such as the Adobe Creative Suite, my own choice would most likely not be best for you. Given your graphic design background, if you find the non-Retina displays sufficient for your needs, I’d recommend that you consider a used 15-inch Mid 2012 MacBook Pro. That model has memory sockets, so you can replace/upgrade the RAM if needed; its internal disk can be replaced by/upgraded with any 2.5-inch 9.5-mm-high SATA hard disk or SSD; and it has a built-in SuperDrive.

  • SSD SATA-III in optibay

    Hi there.
    Should a SATA-III 6gigabit SSD work in the obtibay of a MacBook Pro 13" Early 2011?
    I get 6 Gigabit speed with 3 Gigabit negotiated when using a 5400 rpm HDD in the optibay.
    I'm asking, because I tried inserting a Intel 520 series 120gb SATA-III SSD in the optibay the other day - i was unable to format it from there, even though it showed.
    Regards,

    Ah okay, thank you.
    It's because I broke the SATA cable to the HDD bay.
    I've ordered a new cable, but I'd like to use the SSD untill then, if it was possible.
    Guess I'll have to wait it out, and cross my fingers that the new SATA cable works.
    Thanks again!

  • Macbook Pro SSD vs HD?  Memory?

    I am about to get a MacBook Pro for school. Im going to need it mostly for video editing(final cut , avid etc..), photoshop( the whole  ADOBE CS 5),  music(itunes, IDVD ec..) uploading movies, pictures etc...I need to know what my best option is regarding hard drives, should I invest in the SSD or stick with the standard drive it comes with?
    also if i get the 8gb memory option and stay with the standard hard drive is that good ?
    and whats the difference between 5400 rpm and 7200 rpm?
    i want something with good battery life as well.
    thank you !

    TANYA SABGA wrote:
    ok i think upgrading myself makes the most senseas ive heard more good things about that. Now for the processor what difference does the 2.4GHz to the 2.5GHZ make, is it worth paying the extra $230 since that is not upgradeable?
    No it is not worth what Apple is charging for that upgrade. Actually it is a 2.4 GHz CPU as apposed to the 2.2 GHz CPU.
    That money would be better spent on RAM, Aftermarket for under $50, and at least a 7200RPM  HDD, again Aftermarket for around $120+/-.
    Then get a SATA to USB adapter for under $20 to use the original drive as a backup disk.
    RAM
    http://www.crucial.com/store/mpartspecs.aspx?mtbpoid=9856FD01A5CA7304
    HDD
    http://www.newegg.com/Product/Product.aspx?Item=N82E16822148591
    SATA to USB Adapter
    http://www.newegg.com/Product/Product.aspx?Item=N82E16812232002
    Good Luck

  • 13'' 2.5GHz MacBook Pro (non Retina) - Still worth getting?

    I'm looking into getting a new Mac.
    My thinking at the moment is that the SuperDrive will be much more useful to me than the Retina Display, so I was thinking of getting the older 13'' 2.5GHz MacBook Pro. But I hear this model is being phased out; would I be stupid to get this now instead of one of the newer models?
    What other sorts of things should I be thinking about?
    Thanks for all replies.

    Little Endian,
    it depends on what you need to do with a new Mac. My “new” Mac (bought last year) was a used Mid 2010 model; it suffices for my needs. If you require the higher resolution built-in display, then the non-Retina model can’t compete. I’m not sure which model has the longer battery duration per charge. Physically, the non-Retina models have socketed RAM, so their RAM is user-replaceable; the Retina models have soldered RAM, so their RAM isn’t user-replaceable. The non-Retina models take industry standard 2.5-inch form factor, 9.5-mm high SATA drives; the older Retina models take Mini-SATA SSDs, and the current Retina models take PCIe SSDs, both of which have far fewer choices available if an upgrade is desired. The non-Retina models have Ethernet and FireWire 800 ports; the Retina models require Thunderbolt adapters if either of these is needed. As you’d noted, the non-Retinas model have a SuperDrive; the Retina models would need an external drive. The non-Retina models have a Kensington lock slot; the Retina models don’t. If out-of-warranty repair would be an issue for you, the non-Retina models are easier to repair than the Retina models.

  • Ordering 17" Macbook Pro ~ SSD or Standard HDD??

    I am ordering my new 17" Macbook Pro direct from Apple, and I think I will be going with the 256MB SSD, but am not sure if the added $500 over the cost of a 500MB 7200 RPM SATA Drive is too expensive. Are there other larger, perhaps less expensive after market SSD's that I can install in a new Macbook Pro?

    I'm going to return the SSD to Amazon. Even when it was put in the primary bay, with optical drive re-mounted in it's original space, it would never partition properly. Seems pretty clear at this point that the fault lies with the drive itself.

  • HT5634 How to put windows 8 on MacBook Pro via sata hard drive USB off of other computer

    Hi I have recently purchased a MacBook Pro 15 retina. My old laptop was windows 8 but the motherboard crashed and I have the sata hard drive that has all of my data info including OS would I be able to use the OS on Boot camp without purchasing a new license? Also how would I do that? I have put the hard drive into a portable USB device so I can access it via USB 3.0.

    Others will give a better answer, but I suspect that Windows validation will consider this a "significant hardware change", meaning that it will stop working and/or you won't be able to update. Even so, it costs nothing to give it a try and see what happens.

Maybe you are looking for