"match protocol sip" has no any match with Polycom HDX SIP Session

I am working on QoS for Polycom HDX video device。
Found some strange with command "match protocol sip"
Config is following:
class-map match-any cm-prec-3-in
match access-group name acl-prec-3
match protocol sip   !--->try to catch the sip traffic
match protocol rtcp
match dscp cs3
Router#sh policy-map interface vlan 300 input class cm-prec-3-in
Vlan300
   Service-policy input: pm-classify-in
     Class-map: cm-prec-3-in (match-any)
      789 packets, 294892 bytes
      5 minute offered rate 0 bps, drop rate 0 bps
      Match: access-group name acl-prec-3
        753 packets, 290572 bytes
        5 minute rate 0 bps
     Match: protocol sip !---> no any sip traffic is matched
        0 packets, 0 bytes
        5 minute rate 0 bps
     Match: protocol rtcp !---> RTCP catched
        36 packets, 4320 bytes
        5 minute rate 0 bps
      Match: dscp cs3 (24)
        0 packets, 0 bytes
        5 minute rate 0 bps
      QoS Set
        precedence 3
          Packets marked 789
try to show the nbar version:
sh ip nbar version:
27 sip                  Mv: 2
      Iv:                cisco-phone - 1
      Iv:                telepresence-control - 1
42 cisco-phone          Mv: 1
      Iv:                  sip - 2
Dose that mean this command "match protocol sip" is only supported for Cisco device?
Try to use ACL to match udp port 5060 for the QoS, and it is working.
Try to use comster "ip nbar custom" to re-write the nbar and it is doesn't accept.
Please help to clarify how to use this command.

Hi Patrick
I am working on this one as well. I have a UC560 with SIP Trunk provider Les.NET.
It was working fine until a few weeks ago when something changed on the provider end and broke it. My hunch it is something to do with the SIP REFER.
http://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-communications-manager-express/91535-cme-sip-trunking-config.html
Here is an excerpt from the above page:
Call Transfer
When a call comes in on an SIP trunk to an SCCP Phone or CUE AutoAttendant (AA) and is transferred, the CME by default will send a SIP REFER message to the SP proxy. Most SP Proxy Servers do not support the REFER method. This needs to be configured in order to force the CME to hairpin the call:
Router(config)#voice service voip
Router(conf-voi-serv)#no supplementary-service sip refer
Figure 3 shows the behavior of the CME system with the REFER method disabled.

Similar Messages

Has anyone any experience with a USB-6008 and reading a thermistor value

Labview 8.0 connected to a USB-6008
I am using 'BC Components' NTC Thermistor. I used the express VI to create a Vex input and entered the A,B,& C values from the datasheet. The thermistor is the 10K version and I placed a 10K resistor in series with it. I wired it as is shown in the connection diagram, and applied 2.5 volts to it.
I get completly the wrong temperature readings out of it! I called the NI help line in the UK and the engineer confirmed that I had done everything correctly but couldn't understand why it didn't work.
Any thoughts?
Steve Lawson

I had a similar problem, had it working at one point then screwed it up.
try this:
Attachments:
Temp Pressure EXpress.vi ‏92 KB

Before I buy has there been any problems with new 27 iMacs?

Before I spend my hard earned cash does anyone know if there has been any problems with new 27 iMacs?

Hello richard from Folsom:
Are you inside or outside? ( I could not resist, I lived in Sactown).
Anyway, advice is frequently worth what you pay for it, and mine is free.
If you want it, buy it. The posts above are right on the mark (except waiting is probably overly-cautious). The best advice (from anamusic) is to buy the extended warranty - well worth the money.
Barry

Has anyone had any problems with the 10.0.3 upgrade?

I'm running WinXP and presently have Adobe Reader 9.4.3. Before I upgrade I would like to find out if anyone has had any problems with the new release? The last time I upgraded an Adobe product (Flash) it screwed up my ability to watch videos on my browser.
Any information would be appreciated.
Thanks,
Spin45

Adobe Reader has the original 10.0.0 with its associated vulnerabilities and the patch of 10.0.1 which seems unable to run in protected mode in my environment or any that have roaming profiles. The vulnerabilities that prompted the last two patches (would have been 10.0.2 and 10.0.3) have been forgone by Adobe, because "Protected Mode mitigates those vulenrabilities". See here: http://www.adobe.com/support/security/bulletins/apsb11-06.html
and here: http://www.adobe.com/support/security/advisories/apsa11-02.html
In my opinion, Reader X is not ready, they are soliciting for testers for a new release. Version 9 with its attendant problems seems to be the only viable solution for me, if I can get the patches to apply properly, and the installer to work properly.

Any problems with lion running on core 2 duo 2007 MBPro ?

Curious to hear if anyone has had any problems with Lion before I upgrade.
Thanks.

OK, so this is a shot in the dark, but maybe it's worth a try.
Since the problem only occurs when running on battery, perhaps changing the Energy Saver settings to match the settings used for when it's plugged in will fix the problem. The default settings for how the computer operates are different for the battery and power adaptor. When you unplug the power, the computer automatically shifts to the alternate settings.
So, try this:
-Open System Preferences->Energy Saver
-In the "Settings for" drop-down menu, select "Battery".
-In the "Optimization" drop-down menu, select "Better Performance".
-Under the Sleep tab, choose "Never" for both computer and display sleep and uncheck the box for "Put the hard disk to sleep when possible".
-Under the Options tab, uncheck the first two boxes.
15" MacBook Pro 2.33 GHz Mac OS X (10.4.8)

New motherboard: can it cause any issue with ProApps or Projetcs ?

My iMac G5 Ambiant Light is at the Apple Store to replace the motherboard.
Before the crash, I was working on FCP, DVD Studio Pro, Motion and Color projects.
(Final Cut Studio 2).
Will I have everything back in order after the motherboard replacement?
Anybody has experienced any problem with Pro Apps or projects after a motherboard replacement? Thanks!

Your apps are all on your drives.
The motherboard is not in the equation except it holds the processor and that is not changing, is it?
bogiesan

Any success with Apple Customer Relations?

I was wondering if anyone has had any success with getting a refund for their over-14-day-old hi-res powerbooks by calling Apple Customer Relations? Between the audio looping, lines on display, loud hard drive, and warped case, I'm fed up.
Please share your experiences. Thanks.

I ordered just before 10am Eastern, had the Oct 5th Date, but my status changed to Shipped yesterday, and I can track it on UPS.
Hope yours come through soon. Good Luck!

Since upgrading to 7.0.3 (iPhone 5 64gb, with iTunes Match enabled) all of my music wiped off my phone. Downloading it again, most of the artwork has been mixed up with other artists, and I'm no longer able to stream or download over 3G? Any ideas?

Since upgrading to 7.0.3 (iPhone 5, 64gb, with iTunes Match enabled) almost all of my music has vanished from my phone (weirdly some hasn't).
Downloading it again, most of the artwork has been mixed up with other artists, and I'm no longer able to stream or download over 3G (all tracks greyed out), though my network settings etc are all set correctly.
Lastly since upgrading to iOS 7.0.1 (and beyond) Genuis has become effectively useless: it continually asks me to connect to wi-fi, and if I do it creates playlists mostly composed of tracks by the same artists or those very obviously linked to them- previously it created brilliant, nuanced playlists.
Are these things connected, and how do I fix them?

I have done this on numerous occasions but I think that my Iphone has a defect. After many tries, reinstalls, deletion of content, changing content to be stored on external hard drive, deleting itunes and cleaning computer I managed to get all of the songs on and things seemed okay for a while.
The problem returned about a week ago after downloading a new album from Itunes. I now have 12.5k of songs leaving 10gb spare on Iphone which should be more than enough room to operate properly. Last night it seemed to be dowloading ok (after doing all of the above again for the umpteenth time) this morning it revealed that it had just synched 2.5k of songs and 18gb of "other" on the contents bar. it wont synch now as it says its over capacity. So the 18gb of "other" would probably be corrupted data that means it must corrupt each song as it tries to synch it.
The 2.5k of songs it did synch are working on the Iphone as is every song in the library on Itunes. I did completely delete the new album I bought and redownloaded it from the store then tried to synch just that album and it worked fine.
Just about time to dump apple I think!

TNS:listener could not find available handler with matching protocol stack

Hi,
I am getting the following stack trace in b2b.log file:
2009.01.06 at 14:34:35:869: Thread-108: BusinessLogicLayer - (ERROR) caught error: Error -: AIP-13002: SQL error getting the DataSource
2009.01.06 at 14:34:35:870: Thread-108: IP - (ERROR) java.sql.SQLException: Listener refused the connection with the following error:
ORA-12516, TNS:listener could not find available handler with matching protocol stack
The Connection descriptor used by the client was:
(DESCRIPTION=(ADDRESS_LIST=(ADDRESS=(PROTOCOL=tcp)(HOST=localhost)(PORT=1521)))(LOAD_BALANCE=yes)(CONNECT_DATA=(SERVICE_NAME=test)))
     at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:137)
     at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:292)
     at oracle.jdbc.driver.T4CConnection.logon(T4CConnection.java:327)
     at oracle.jdbc.driver.PhysicalConnection.<init>(PhysicalConnection.java:429)
     at oracle.jdbc.driver.T4CConnection.<init>(T4CConnection.java:150)
     at oracle.jdbc.driver.T4CDriverExtension.getConnection(T4CDriverExtension.java:31)
     at oracle.jdbc.driver.OracleDriver.connect(OracleDriver.java:608)
     at oracle.jdbc.pool.OracleDataSource.getConnection(OracleDataSource.java:217)
     at oracle.jdbc.pool.OracleConnectionPoolDataSource.getPhysicalConnection(OracleConnectionPoolDataSource.java:113)
     at oracle.jdbc.pool.OracleConnectionPoolDataSource.getPooledConnection(OracleConnectionPoolDataSource.java:76)
     at oracle.jdbc.pool.OracleConnectionPoolDataSource.getPooledConnection(OracleConnectionPoolDataSource.java:58)
     at oracle.jdbc.pool.OracleConnectionCacheImpl.getNewPoolOrXAConnection(OracleConnectionCacheImpl.java:493)
     at oracle.jdbc.pool.OracleConnectionCacheImpl.getPooledConnection(OracleConnectionCacheImpl.java:368)
     at oracle.jdbc.pool.OracleConnectionCacheImpl.getConnection(OracleConnectionCacheImpl.java:306)
     at oracle.jdbc.pool.OracleConnectionCacheImpl.getConnection(OracleConnectionCacheImpl.java:285)
     at oracle.tip.buslogic.common.DBConnectivity.getConnection(DBConnectivity.java:151)
     at oracle.tip.buslogic.common.ExecutionContextImpl.getService(ExecutionContextImpl.java:379)
     at oracle.tip.buslogic.common.ExecutionContextImpl.setRuntimeActiveandQuiescing(ExecutionContextImpl.java:799)
     at oracle.tip.adapter.b2b.data.B2BExecutionContext.setRuntimeActiveAndQuiescing(B2BExecutionContext.java:130)
     at oracle.tip.adapter.b2b.data.B2BExecutionContext.activate(B2BExecutionContext.java:98)
     at oracle.tip.adapter.b2b.data.DBContext.initialize(DBContext.java:90)
     at oracle.tip.adapter.b2b.data.DataContext.getNewDBContext(DataContext.java:365)
     at oracle.tip.adapter.b2b.data.DataContext.getDBContext(DataContext.java:346)
     at oracle.tip.adapter.b2b.transport.InterfaceListener.onMessage(InterfaceListener.java:232)
     at oracle.tip.transport.basic.FileSourceMonitor.processMessages(FileSourceMonitor.java:858)
     at oracle.tip.transport.basic.FileSourceMonitor.run(FileSourceMonitor.java:302)
When I ran the enquire script. I am getting the following exception:
IPEnqueue start...
Action Name = null
oracle.jms.AQjmsException: ORA-00600: internal error code, arguments: [kwqbgqc: bad state], [1], [1], [], [], [], [], []
ORA-06512: at "SYS.DBMS_AQIN", line 454
ORA-06512: at line 1
at oracle.jms.AQjmsProducer.enqueue(AQjmsProducer.java:1180)
at oracle.jms.AQjmsProducer.publish(AQjmsProducer.java:1407)
at oracle.jms.AQjmsProducer.publish(AQjmsProducer.java:1512)
at oracle.tip.adapter.b2b.data.IPEnqueue.main(IPEnqueue.java:201)
[Linked-exception]
java.sql.SQLException: ORA-00600: internal error code, arguments: [kwqbgqc: bad state], [1], [1], [], [], [], [], []
ORA-06512: at "SYS.DBMS_AQIN", line 454
ORA-06512: at line 1
at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:124)
at oracle.jdbc.driver.T4CTTIoer.processError(T4CTTIoer.java:315)
at oracle.jdbc.driver.T4CTTIoer.processError(T4CTTIoer.java:281)
at oracle.jdbc.driver.T4C8Oall.receive(T4C8Oall.java:638)
at oracle.jdbc.driver.T4CCallableStatement.doOall8(T4CCallableStatement.java:183)
at oracle.jdbc.driver.T4CCallableStatement.execute_for_rows(T4CCallableStatement.java:872)
at oracle.jdbc.driver.OracleStatement.doExecuteWithTimeout(OracleStatement.java:1085)
at oracle.jdbc.driver.OraclePreparedStatement.executeInternal(OraclePreparedStatement.java:2983)
at oracle.jdbc.driver.OraclePreparedStatement.executeQuery(OraclePreparedStatement.java:3025)
at oracle.jms.AQjmsProducer.enqueue(AQjmsProducer.java:1110)
at oracle.jms.AQjmsProducer.publish(AQjmsProducer.java:1407)
at oracle.jms.AQjmsProducer.publish(AQjmsProducer.java:1512)
at oracle.tip.adapter.b2b.data.IPEnqueue.main(IPEnqueue.java:201)
Error -: AIP-13121: Connection-related error. Please verify that the database server is running.: java.sql.SQLException: Closed Connection
at oracle.tip.buslogic.common.SessionDownException.isSessionDown(SessionDownException.java:96)
at oracle.tip.common.IPException.initIPException(IPException.java:179)
at oracle.tip.common.IPException.<init>(IPException.java:114)
at oracle.tip.repos.core.persistency.DCException.<init>(DCException.java:68)
at oracle.tip.repos.core.driver.CatalogDriver.disconnect(CatalogDriver.java:1666)
at oracle.tip.repos.core.persistency.PersistencyService.disconnect(PersistencyService.java:578)
at oracle.tip.buslogic.common.ExecutionContextImpl.disconnectService(ExecutionContextImpl.java:602)
at oracle.tip.buslogic.common.ExecutionContextManager.cleanContextResources(ExecutionContextManager.java:629)
at oracle.tip.buslogic.common.ExecutionContextManager.leaveContext(ExecutionContextManager.java:581)
at oracle.tip.buslogic.common.ExecutionContextManager.leaveContext(ExecutionContextManager.java:720)
at oracle.tip.adapter.b2b.data.IPEnqueue.main(IPEnqueue.java:245)
Caused by: java.sql.SQLException: Closed Connection
at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:124)
at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:161)
at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:226)
at oracle.jdbc.driver.PhysicalConnection.rollback(PhysicalConnection.java:1041)
at oracle.jdbc.OracleConnectionWrapper.rollback(OracleConnectionWrapper.java:90)
at oracle.tip.repos.core.driver.CatalogDriver.disconnect(CatalogDriver.java:1662)
... 6 more
I tested the database and it was up. Any help is appreciated.

You may be interested in http://www.tek-tips.com/viewthread.cfm?qid=1368266&page=10

I continue to receive message that "We could not complete your iTunes Store request. An unknown error occurred (4002). Please try again later." This has been happening every time iTunes Match runs in background. Any suggestions for a cure?

I continue to receive message that "We could not complete your iTunes Store request. An unknown error occurred (4002). Please try again later." This has been happening every time iTunes Match runs in background. Any suggestions for a cure?

Found a potential solution here:
https://discussions.apple.com/thread/4332757
Gsleeroy
Re: error 4002 in itunes match do you have a solution?
Sep 23, 2012 10:08 AM (in response to matracaelcan)
Hi All,
I had this problem today myself, and was frustrated repeatedly by the '4002' error.
I have literally just fixed the issue by doing the following steps:
1: Go to the 'Store' tab and select 'Turn Off iTunes Match'
2: Return to the 'Store' tab and select 'Update Genius'
3: Wait for this to complete succesfully, the return to the 'Store' tab once more and select 'Turn On iTunes Match'.
4: iTunes Match will now go through the motions and should succeed!
I hope this helps

HT2589 No matter how many times I've reset my iphone4 and reentered my account information I can't assess my music in iTunes Match or purchase or update any apps or music. How can I fix this. On enabled devices iTunes on my computer shows my iPhone with ?

I can't access iTunes Match or make any Music or app purchases or updates after updating to iOS 6. No matter how many times I've reset my iphone4 and reentered my account information I can't assess my music in iTunes Match or purchase or update any apps or music. How can I fix this. On enabled devices iTunes on my computer shows my iPhone with ? marks.

This may help.
Fix for “No Content” on iPhone & iPod after iOS 4.2.1 update
The try the standar fixes:
- Reset. Nothing will be lost.
Reset iPod touch: Press and hold the On/Off Sleep/Wake button and the Home
button at the same time for at least ten seconds, until the Apple logo appears.
- Restore the iPod from backup via iTues
- Restore the iPod factoery defaults/new iPod.

Class-map does not support match protocol ssl

I have several 1941/k9's that do not have the class-map command: to suppot ssl. System image is c1900-universalk9-mz.SPA.152-1.T.bin.
class-map match-any af31
match protocol ssl <-- missing.
I did some google searches but come up with nothing.
Is the fix to upgrade IOS? I have found it on other routers running c1900-universalk9-mz.SPA.152-4.M4.bin. I would just upgrade and check but have an extensive change review board with questions before doing so.
Thanks for advice,
Haydn

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
I'm not current on NBAR (or NBAR 2), but NBAR used to support loadable modules (PDMs?). Sometimes Cisco would provide those so you could add match protocols without upgrading your IOS.
Otherwise the "fix" would be to upgrade your IOS.
Lastly, depending on what it matching SSL really means to you, using port based ACLs might suffice (in fact, some NBAR match protocol is only really that, but some NBAR matches regardless of the port usage).
PS:
Also on the subject of SSL, don't forget much can use it. I once matched on it for the purposes of providing secure shell higher queuing priority, worked great for SSH, not so great when secure copy (SCP) also matched against it.

ZBF, "match protocol http" makes youtube and some other sites unusable

Hi, Cisco 7201, IOS:
Cisco IOS Software, 7200 Software (C7200P-ADVENTERPRISEK9-M), Version 15.0(1)M8, RELEASE SOFTWARE (fc1)
I have implemented zone based firewall with LAN 2 INET policy like:
class-map type inspect match-any CLASS_LAN2INET
match protocol http
match protocol https
match protocol tcp
match protocol udp
match protocol tcp
policy-map type inspect LAN2INET
class type inspect CLASS_LAN2INET
inspect
class class-default
pass
many downloads gets stalled, slowed down, sky.fm radio plays with pauses, youtube page get loaded but videos not played.
some (some!) dowloads proceed without problems, like http://ftp.freebsd.org
web pages gets opened mostly without problem
First i blamed ISP, they checked their side and didn't find any problems.
Then is disabled firewall (should have to try it first) and everything started to work like a charm.
Then i narrowed down to removing "match protocol http".
If not use "match protocol http", everything works ok.
Is it a bug, is there a fix? any options to tweak "http"?

jcarvaja wrote:permit tcp any any eq 443...no match protocol HTTPS
I wonder, how Cisco inspects HTTPS on L7? It's encrypted, after all..
ip access-list extended Juliopermit tcp any any eq 80 class-map type inspect Juliomatch access-group name Julioclass-map type inspect CLASS_LAN2INETno match protocol HTTP Try it and let me know,
I came to this workaround myself, but it's "workaround", not a fix.
Just tried on another 2951 router with 15.1(4)M6 IOS. It has the same issue - youtube does not play videos.
How no one noticed such bug?
PS:
when starting youtube video, it spamming with:
Jul 26 11:13:24: %FW-4-TCP_OoO_SEG: Dropping TCP Segment: seq:1998688742 1500 bytes is out-of-order; expected seq:1998647862. Reason: TCP reassembly queue overflow - session 10.10.10.128:55547 to 46.61.155.145:80 on zone-pair zp_LAN2INET class zbfc_INSPECT_OUT
surgut-inet-2951#
Jul 26 11:13:25: %FW-4-TCP_OoO_SEG: Dropping TCP Segment: seq:1993449876 1500 bytes is out-of-order; expected seq:1993385636. Reason: TCP reassembly queue overflow - session 10.10.10.128:55548 to 46.61.155.145:80 on zone-pair zp_LAN2INET class zbfc_INSPECT_OUT
surgut-inet-2951#
Jul 26 11:13:26: %FW-4-TCP_OoO_SEG: Dropping TCP Segment: seq:1993451336 1500 bytes is out-of-order; expected seq:1993387096. Reason: TCP reassembly queue overflow - session 10.10.10.128:55548 to 46.61.155.145:80 on zone-pair zp_LAN2INET class zbfc_INSPECT_OUT
surgut-inet-2951#
Jul 26 11:13:29: %FW-4-TCP_OoO_SEG: Dropping TCP Segment: seq:1998717942 1500 bytes is out-of-order; expected seq:1998653702. Reason: TCP reassembly queue overflow - session 10.10.10.128:55547 to 46.61.155.145:80 on zone-pair zp_LAN2INET class zbfc_INSPECT_OUT
surgut-inet-2951#
Jul 26 11:13:33: %FW-4-TCP_OoO_SEG: Dropping TCP Segment: seq:1998719402 1500 bytes is out-of-order; expected seq:1998655162. Reason: TCP reassembly queue overflow - session 10.10.10.128:55547 to 46.61.155.145:80 on zone-pair zp_LAN2INET class zbfc_INSPECT_OUT
surgut-inet-2951#
Jul 26 11:13:42: %FW-4-TCP_OoO_SEG: Dropping TCP Segment: seq:1998720862 1500 bytes is out-of-order; expected seq:1998656622. Reason: TCP reassembly queue overflow - session 10.10.10.128:55547 to 46.61.155.145:80 on zone-pair zp_LAN2INET class zbfc_INSPECT_OUT
surgut-inet-2951#
Jul 26 11:13:52: %FW-4-TCP_OoO_SEG: Dropping TCP Segment: seq:1998722322 1500 bytes is out-of-order; expected seq:1998658082. Reason: TCP reassembly queue overflow - session 10.10.10.128:55547 to 46.61.155.145:80 on zone-pair zp_LAN2INET class zbfc_INSPECT_OUT
parameter-map has default settings, there is only one user on this router (fresh from the box)

Match protocol Other

Hi all,
i've been using a the classmap "class-map type inspect match-any min-cls-insp-in-out" in a policymap "policy-map type inspect min-pm-in-out" in the zone security "ccp-zp-in-out source" for my firewall. I've just noticed a "match protocol Other" that i've for sure didn't insert, can you tell me what is the functionality of this parameter??
it was not making any sense to me and so i've tried to:
conf
class-map type inspect match-any min-cls-insp-in-out
no match protocol Other
^
% Invalid input detected at '^' marker.
i've tried to remove the "match protocol ftp" and the ftp traffic was actually been blocked by the firewall.
class-map type inspect match-any min-cls-insp-in-out
match protocol dns
match protocol ftp
match protocol icmp
match protocol imap
match protocol rtsp
match protocol ssh
match protocol pop3s
match protocol pop3
match protocol imaps
match protocol https
match protocol Other
match protocol ntp
policy-map type inspect min-pm-in-out
class type inspect min-cls-invalid-in-src
drop log
class type inspect min-cls-insp-in-out
inspect
class type inspect min-cls-insp-smtp
inspect
class type inspect min-http-cmap
inspect
class type inspect min-cls-insp-im
inspect
class class-default
drop log
zone-pair security ccp-zp-in-out source in-zone destination out-zone
service-policy type inspect min-pm-in-out
thank you !!

I get the same problem on my Cisco 877 ADSL Router
It seems that when i remove a match protocol command, the match protocl Other seems to be dropped in there and like you have experienced, you can't just do a "no match protocol Other"
I would have to remove the whole class-map and add it again. It's fairly simple to do, just copy/paste into notepad, remove the match protocol Other line, do a no class-map and then copy and paste your previous classmap config (with the match protocol Other removed) back in again.
I'm running version 15.0 M7 and unfortunately i get connection problems with my ADSL provider if i use a later firmware version.
The weird thing is, it doesn't do it to any other class maps. Only this one. Perhaps if the class map has more than a certain number of match commands then this problem occurs. My other classmaps only have 2-3 match lines in it and i haven't had the chance to test.

HT1766 Recently updated my iPhone 4s to the iOS 6. Now I can not install application updates, my music library has vanished, iTunes Match (in Settings) keeps setting itself to "Off".

I recently updated my iPhone 4s to the iOS 6. Now I can not install application updates, my music library has vanished, iTunes Match (in Settings) keeps setting itself to "Off". I have also logged off of iTunes in Settings, and it will not let me log back in. Just a few moments ago when I again tried to log into iTunes, it asked me for my Password, then replyed that I had no Match account; but I do. Is Restore the best option?
Any suggestions

I couldn't find the edit button on my original post so I am posting an update here.
I have gone through more apps and have had good luck on all but one more. And it's not that the app doesn't work, I am talking about the Yahoo Weather app, It works fine, but when you swipe between cities the screen lags a bit and it sometimes doesn't move between pages the way it should. On iOS 7.1.2 it was smooth as butter but on iOS 8.0, not so much. I will post a note in the app store to let them know. I really like the Yahoo app better than the new stock app.
I have been going through my games and they all work fine. Angry Birds (Original and Stella), Canabalt, Minecraft, Bejeweled 2, Silly Walks, PopWords, Doodle Jump, Deep Green all seem to work just fine.
Starbucks app works as it should.
I will stop back again next week after I have had the weekend to play with it in detail and post my thoughts again.

"match protocol sip" has no any match with Polycom HDX SIP Session

Similar Messages

Maybe you are looking for