Mgcp outgoing issue

Hi all ,
we have configured new PRI with MGCP protocol , incoming calls are working problem is with outgoing calls . we have checked all possiblities in called and calling type partition and css . attaching debug of mgcp packets and isdn q931 . please look into the issue and reply .

Hi ,
changed settings in route group still same fast beep sound , no outgoing but incoming working fine . details from SP are
Mode
TE
Protocol
ETSI
CRC-4
No
TX Clock
L1-RX
Framing
PCM31
Code type
2e15
Rate
2048M
Call Type
Voice
B Channel
Automatic
Test code type
2e15
UUS
No
Layer 2 TEI
0
Signalling timeslot
16

Similar Messages

N97 email outgoing issue

Hi Guys,
I've setup my gmail account on the device using the wizard and receipt of email seem to be working fine.
But when I try to send out an email from the device only thing it does is queining the email in the outbox (of course after connecting to the mail box). It doesn't seem to be sending out the email.
Can anybody let me know what I should do to be able to send out an email?
email account: gmail
email client on the device: Default N97 builting email client
outgoing email port:587 (I've change this from the default 465 to 587 as google advice to do so. Keeping this to 465 never sends the email).
I'm pretty sure there are guys out there who've got these things working smoothly. Any support from such a guy is highly appreciated.
Thanks.

I had the same problem, tryed to follow instructions above - did not work for me. Finally I deleted the account setting and follow the wizard. Please note, there are two differnet wizards, the one that is in "welcome application" did not work for me, the other one - that is under welcome screen - above "options" worked fine.
Learning experince -
1. do not go with e-mail settings
2. delete the email account you tryed to establish
3.do not go with "welcome" application"
4. go with the email setup that is on your main telephone screen (the screen you see to setup multiple email options - ovi, yahoo, etc)
Hope, it helps in you case

MGCP flow problem - ASA

The following is the setup and the problem we have:
* MGCP call agent -- ASA 5510 -- vpn tunnel -- linksys -- MGCP gateway
* VPN tunnel setup is in aggresive mode (initiated as needed from linksys).
* When MGCP call agent is up but the vpn tunnel is still down, MGCP traffic (udp/2427) tried to reach gateway and failed --> this is as expected.
* Next, linksys brings up the vpn tunnel
* Any other IP traffic can go through the tunnel, but not MGCP traffic from call agent to gateway.
* Checked from packet tracer: it passed phase 1 & 2 (checking the flow), it found existing flow and used that flow. Then it stuck there, looks like it didn't know where to go next (no ACL or route checking).
We noticed that the annoying following workaround will make the MGCP goes through.
* shutdown MGCP call agent
* disconnect vpn tunnel from linksys
* system reload the ASA5510
* after ASA5510 is up, linksys initiate the vpn tunnel
* after vpn is up, bring up MGCP call agent
* MGCP traffic goes through the tunnel
It seems like ASA MGCP flow table is not updated if there is status change in VPN tunnel. Any idea how to fix this ?

Thanks for the reply.
However that wasn't mgcp ispection issue, it was more on dynamic vpn configuration issue. The setup is dynamic vpn initiated from remote sites (aggresive mode).
Worked with Cisco TAC and got the workaround. Following is the summary, hope it's useful.
1. Previous dynamic vpn config was:
crypto dynamic-map outside_dyn_map 20 set transform-set VPNHigh
When the tunnel was down and the call agent (central) was sending traffic to the call gateway (remote), the ASA created a connection to send the traffic out in the clear as it didn't match any crypto access-list due to the tunnel being dynamic.
2. The call agent (cetral) continued to attempt to send traffic to the call gateway (remote), which kept the conn up, even when the tunnel came up.
3. When the tunnel came up, the ASA continued to use the existing conn and sent the traffic out in the clear.
4. This is very similar to bug: CSCse36327 - GRE Packets are no longer encrypted and are sent out in the clear
http://www.cisco.com/cgi-bin/Support/Bugtool/onebug.pl?bugid=CSCse36327
Even though that mentions GRE, it's the same issue.
5. After the tunnel was up and "clear local-host " was issued, the conn was torn down and a new conn was built to go over the tunnel.
6. To avoid this situation, a crypto acl for this dynamic tunnel was created:
access-list dyn-mgcp line 1 extended permit ip
crypto dynamic-map outside_dyn_map 20 match address dyn-mgcp
crypto dynamic-map outside_dyn_map 20 set transform-set VPNHigh
crypto dynamic-map outside_dyn_map 40 set transform-set VPNHigh
Now, when the call agent (central) sends traffic to the call gateway (remote) when the tunnel is down, the ASA drops the packets and doesn't build a conn until the tunnel is brought up.
7. This was tested by bringing down the tunnel and watching incoming packets from the call agent (central) to the call gateway (remote) and verified they weren't being sent out in the clear. The tunnel up was brought up and traffic started being passed between the call agent and the call gateway.

Iphoto / Sharing via Email issues with 10.10.2

Hope some one knows the answer ... I have had so many problems with iPhoto since covering across to Yosemite. This is the latest.
I am trying to share photos through iPhoto using e-mail. This has only just stopped working 36 hours ago. I have checked the e-mail server for incoming and outgoing issues by sending an e-mail and attaching a photo the usual way - no problem. When I try to do this through the SHARE option in iPhoto I get the following error message. Does anyone have any ideas how to fix this? I am on the latest version of iPhoto 9.6.1. Thanks for any insight / help.

When I try to do this through the SHARE option in iPhoto I get the following error message. Does anyone have any ideas how to fix this? I am on the latest version of iPhoto 9.6.1. Thanks for any insight / help.
If recreating the account does not help, the reason may be two-step verification. Did you recently enable two-step verification for iCloud?
Are you sending from your iCloud Mail address?
If you had two-step verification enabled, you have to set up an app-specific password for iPhoto, if you want to use iPhoto as a Mail client.
See the post below:
Re: I am using iPhoto version 9.6 and I can no longer get an email sent with a photo attached. I get an error message saying the email did not go through because the server did not reply. I can send the photo with Mail. Help!in response to Gary Kissler
This solution is for those of you using 2-step verification for your Apple ID and are using iCloud as the mail server that you are trying to mail photos with.
I too had this issue. The problem in my case occurred because I had setup 2-step authentication for my Apple ID. If you have done this then you will get the error message "the mail server did not recognize your email/password...". To solve the problem go to:
https://appleid.apple.com
Click "Manage Your Apple ID"
Verify your identity with the device you selected (if this step does not show up then you have not likely set up 2-step authentication and this is not your solution)
Click Password and Security in the left column
Click Generate an app-specific password
Enter iPhoto as the name of the app
Copy the password and paste this into the password box in iPhoto where you would normally enter your apple ID (in the mail account section in iPhoto preferences).
And...voila' (I hope)
Re: I am having trouble e-mailing from iPhoto the message I get is E-mail server didn't recognise your username/password combination

PC issues? - one Mac (iChat 2.5) works, another (iChat3.1) doesn't

Hello.
Yet another "video chat with PC" issue. But it has me stumped. This is the situation:
I am running a G4 Powerbook (Panther 3.9) with iChat 2.1. I am able to successfully video chat with my big (as in older) sister who is running Windows XP and latest version of AIM(5.9). I am running over a wireless network through a Linksys ADSLmodem/Router combo (WAG54G ver 2). All great - bit choppy but more than adequate.
Here's the thing that is tres frustrating:
Another computer - an iBook running Tiger 10.4.3 and iChat 3.1 - on the same network (wireless etc) wont video chat with the same PC user!! I get my sister (PC user) to initiate the video chat, I accept it, and then she is able to see and hear me, but I only hear her -- What gives?
Seems to be that the problem is not with the XP setup (else it wouldn't work with the Panther system - right?).
Does this have something to do with DSCP QoS technology (something which I know nothing about) as indicated here: http://www.mvldesign.com/videoconferencetutorial.html?
Is is a router setup problem?
Any help, redirections, caring words of support would be great...
Regards, and thanks
Simon

Thanks for your responses. James - I have added you as a "buddy" - my buddyname (mac) is [email protected] - when you are next online I might try it out.
Ralph - I have had a good look over your site...
Neither of the macs had (and still don't!) their respective firewalls turned on... so doesn't seem to be the problem.
In terms of port forwarding on the modem/router -- it is using it, I tried to set up port forwarding for udp and tcp on port 5060 (for the specific ip of the iBook - which I have now manually set). .. but hasn't made any difference. But the router setup is very different from information on your site...
I also tried a completely different (much cheaper, and wired) router (with default settings) - but no luck - in fact, couldn't even replicate the "best" situation of this problem.
Just to reiterate, there is no problem with audio, and my sister gets video of me - but me not of her - so this would indicate my router/modem (wag45g ver 2) is not letting video data in - right? (except when I am using iChat 2.1 on PB running panther). This situation is NOT replicated when I invite her to chat - in this case we can't even get a "link" (an "outgoing" issue???).
I also tried turning off router's firewall - but it made no difference.
Apologies for my very nascent understandings of networks. When I read the word "packets" my eyes glaze over, and i start thinking of packets of potato chips.
mmmm ... chips.
Regards
Simon

IE8 + Adobe Reader XI crashes

Hi,
We are having outgoing issues with Internet Explorer 8 (8.0.7601.18487) and Adobe Reader XI (11.0.6.70).
Each time users open a PDF file via Internet explorer and close tab or whole Internet explorer application IE crashes.
Below you can find error window:
And this is how it looks in Event log:
Faulting application name: iexplore.exe, version: 8.0.7601.18487, time stamp: 0x5385a4c5
Faulting module name: AcroRd32.dll, version: 11.0.6.70, time stamp: 0x52b528d0
Exception code: 0xc0000005
Fault offset: 0x0001e184
Faulting process id: 0x1194
Faulting application start time: 0x01cfd24eda40b58a
Faulting application path: C:\Program Files (x86)\Internet Explorer\iexplore.exe
Faulting module path: C:\Program Files (x86)\Adobe\Reader 11.0\Reader\AcroRd32.dll
Report Id: d3a117e0-3e42-11e4-992e-0c8bfd2db26a
Because of different application used in organization we cannot change pdf open behavior to Adobe Reader application itself. Sometimes PDF files have to be opened in IE (Display PDF in browser).

Hi Pat,
Unfortunately update didn't help at all.
Please find same error for latest version:
Faulting application name: iexplore.exe, version: 8.0.7601.18571, time stamp: 0x53eee2cc
Faulting module name: AcroRd32.dll, version: 11.0.9.29, time stamp: 0x5412b4a0
Exception code: 0xc0000005
Fault offset: 0x000c8faf
Faulting process id: 0x1250
Faulting application start time: 0x01cfd264d4d64e04
Faulting application path: C:\Program Files (x86)\Internet Explorer\iexplore.exe
Faulting module path: C:\Program Files (x86)\Adobe\Reader 11.0\Reader\AcroRd32.dll
Report Id: 1ad606af-3e58-11e4-b657-00155d641207

Mail Unable To Connect Error

For the last day and half, I've been unable to access my iCloud email through Mail on Lion. I get the following error:
The server returned the error: The connection to host p03-imap.mail.me.com on port 143 failed.
According to the system status, iCloud Mail did have an issue but apparently they think it's resolved. Anyone have any idea why I'm still getting an error? I have no problems accessing iCloud Mail on any other devices or through Safari.

I did. The results remained - it didn't work for me. All devices, changing password, deleteing/re-adding acount, changing port/SSL in the mail app on my workstation, and on the laptop, even logging onto iCloud-online - no email, period. Eventually got support on the phone, answered a bunch of questions, sat on hold, got passed on to a supervisor, sat on hold for another while and they came back saying my email was in migration and I should be back online tomorrow - TOMORROW!
I promptly lost it. Completely. I "migrated" weeks ago! And if that wasn't migrating what was I doing? Well, apparently although I migrated all my devices after updating software and had done everything right, I hadn't actually been moved onto the new iCloud servers and there was a bottle neck somewhere in the process that should have finished at 3:30 am without my ever being aware. Lots of apologies were extended but nothing could be resolved sooner - frankly I almost lost it again hearing this because the business day was over and I have no idea what was missed because of this. She did however give me her number to call her in the morning if it had not resolved - by the time I finished talking to her exchanging info and cooled off (about 15 minutes later) the problem resolved itself and I am back up.
& now if you will excuse me I now have an outgoing issue to address (errr!)... I will leave with this clue however - I was told that if you are not having success with any devices but are able to at least log-on at iCloud-online, even if you still can't access email there (contacts/calendars appeared fine, just could get email to load), then its not you. You need to call support... or wait for it to clear on its own.

SMTP / Gmail solutions

My current workarounds for SMTP / gmail issues:
1) SMTP server issue - basically, its hard to know what SMTP server to use since you change location / data provision constantly. This is my current solution:
a. Get a gmail account
b. add the account that you want to use as an account in gmail (see settings)
c. set up the outgoing server on iPhone for gmail settings (under whatever mail account you want in settings -> mail -> account -> outgoing server):
1. pop.gmail.com:587
2. user name (full email address or just gmail user name)
3. pass word
4. turn on outgoing SSL in advanced
5. use password authentication in advanced
Because the account is added in gmail, gmail will not rewrite the from address in your outgoing emails. You cannot currently set up gmail to reforward these messages to some other account due to the way filters work in gmail. (For example, you cannot set up gmail to reforward work emails sent from your iphone via gmail back to your work address so that they could be saved in a sent box of your work email). Anyway, this solution will work for any email address on any network (wifi or edge).
You may want to set up a filter per below for your work (or whatever) email so that you don't redownload sent messages from your iPhone back to your iPhone.
2) The annoying sent emails in gmail come back to your iphone. This only applies to iPhone users who are checking gmail on their iPhone. Set up a filter in gmail which deletes all messages from you except those that are written from you and to yourself. This is done by putting [email protected] in the from field in the filter settings and putting to:([email protected]) in the doesn't have field.
Hope these help!
MBP Mac OS X (10.4.10) also PCs

Hi racemize-
Thanks for the solution. It worked great! My ISP is Roadrunner (Time Warner in So Cal) and I was having the same outgoing "issues" that seem to be affecting a lot of iPhone users (regardless of what ISP they have).
One question...now all my e-mails sent from my iPhone will show up as "<gmail username/e-mail> sent on behalf of <roadrunner username/e-mail>". Is there any way to get ride of that and have it just show up as <roadrunner username/e-mail>"? When people reply it does go to the correct reply-to address (roadrunner) but having that "...sent on behalf of..." is a bit annoying.
Thanks!
Windows XP Pro
Windows XP Pro
Windows XP Pro

Help on email

i cant get email to the people in my company! help me! I have roadrunner. my roadrunner extension is @sc.rr.com, my co-workers is @securityvisionmb.com. I get an error message about authentification. I tried changing my outgoing port. it didnt help. Any ideas?
thanks!

The outgoing issues are related to the access port and server information from carrier, you may want to contact Time Warner and have them verify this information because some times they use a doffrent set of settings for modile devices. I experiance this all the time with TW because they have a habit of updating the server settings and not inform customers. This is why I use my Yahoo account as my default account to send all emails.

Ovi manual set-up and synchronization

i'm having difficulty synchronizing my phone contacts to ovi. can someone help me please?

Open the Connection Doctor under Window in the Menu bar when Mail is active.
You will see red or green icons to indicate if you are connected. You can click on Show Detail to get more info.
For outgoing issues, it's usually the password that needs to be re-entered.
Edit SMTP
Select Account
Under the Advanced tab enter password

Issue in Outgoing Payments

Hi
I have an issue in Outgoing payments. Our client books the invoice at gross level through MIRO. Then there are deductions which are made based on various parameters like quality, volume, trade and other such parameters. Now They have a process in Legacy, where in the user after booking the invoice selects same and enters the various discounts in the system. System then generates the payment advise with the details of deductions and the invoice details, which is sent to the vendor. A payment advise document number is also generated.
While preparing the outgoing payment in legacy, the user just selects the payment advise number and the bank name and the system creates the cheque and passes the accounting entries.
We suggested the user to pass the deductions through MIRO. Then the accounting entries for outgoing payment could be passed through F110 /F-53/F-58, where in the invoice and the bank have to be selected. Thereafter, with reference to the outgoing payment document, a cheque is perpared manually if using T code F-58 or F-53 or automatically, if using F110. We suggested to the client to develop an ABAP form which would give the out put in the same way as legacy.
However, the client is insisting that the process should be mapped exactly as in legacy.
Pls suggest
Regards
Sanil

Hi
The clinet is getting discounts. However, they are paying the vendor with the net amount only (I.e, after discounts). However, the process should work in the same way as legacy
Regards
Sanil

Mail OUTGOING SERVER ISSUE

How can I change the server for outgoing mail?? I only have one and it prompts me with this:
Cannot send message using the server
smtp.mac.com:sharrkmedia
The connection to the server "smtp.mac.com" on port 25 timed out.
Select a different outgoing mail server from the list below or click Try
Later to leave the message in your Outbox until it can be delivered.
any thoughts?

If you look around the discussions you will see there are many folk with the same issue. It looks like a serious bug in Mail. I have the same problem. I believe it has nothing to do with what port you are using. Port 25 should be the right port for most folk.
Some people have managed to get things working but it seems to me they've sorted things by fluke rather than logic. There doesn't seem to be a fix-for-all.
I have read these things have worked for some folk (not me)...
-reset router/computer
-erase email accounts and manually create them again
-re-enter (ie delete and re-type) the SMTP server address(es)
-switch on/off/on smtp authentication (it should be off for most folk)
-plus others I've forgotten now.
Non of this worked for me.
Personally, I believe these are not fixes but they might have an effect on the problem for some people.
I'm waiting for a solution and using my old computer in the mean time

Technical issue SAP F110 related issue. getting extra characters in outgoing file from sap.

Hi Technical guru's,
SAP system creating a outgoing file through F110- t-code, this outgoing file has extra characters (DOC.NO:)
We need to remove these extra characters. Once Payment run has been carried out through F110, in SM37 in job spool it is showing like screen attached with name “file from sm37”.
But when we look in to outgoing file directory extra characters as I mentioned above is appearing below is the related screen attached with name “out gooing file”.
Gurus can anyone please suggest me where I can check about this. I have checked the program available in the job as well in the F110 transaction.But could not find any hint.
Programs which I find in SM37.
SAPF110S
SAPFPAYM_SCHEDULE
RFFOSE_B
Programs which are available in F110.
RFFOAVIS
RFFOEDI1
RFFOSE_B
Does extra characters coming through functional configuration (DME configuration) or coming through SAP standard programs.
I am Technical person. I need to solve this issue guys please help me in this.
If above information is not sufficient let me know what are the other information should I provide.

I didn't get any resolution so far also I can't convert into Adobe form because this is a production issue which should be fix by making the requied setting or changes in SAP script itself we can't go for new developmet for this isuue.

Mail outgoing email issues

Yosemite outgoing Mail issues have been all over Internet since last Fall. I still have not seen Apple address the issue! Some suggestions from OS X Daily, etc. involve pref changes. However, I find that the pref changes disappear after they are made. I realize they must be selected to "save" but that option does not always present itself. Outgoing mail going as "reply" or forward" hangs up and creates an "outbox" which continues to try to send but has no success. This emails appear to be corrupted once they go there and must be trashed.
The only way I can get a "reply" or "forward" message out is to add a pdf doc at the end of the text in which I simply type "Intentionally Left Blank" so the receiver will not wonder why it is there. From now on, I think I will add "Page will remain blank until Apple wakes up and fixes this essential Mail app"! Perhaps we could add a live "clock" (like the national debt clock) that could continue to show the hours, days, weeks and months in which Apple failed to respond.
Can any Mac users help?
Ed Jones
Commander, USN (Ret.)

Problems such as yours are sometimes caused by files that should belong to you but are locked or have wrong permissions. This procedure will check for such files. It makes no changes and therefore is not, in itself, a solution.
First, empty the Trash, if possible.
Triple-click anywhere in the line below on this page to select it, then copy the selected text to the Clipboard by pressing the key combination command-C:
find ~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $ 2>&- | wc -l | pbcopy
Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
Paste into the Terminal window by pressing command-V. The command may take a noticeable amount of time to run.
Wait for a new line ending in a dollar sign ($) to appear.
The output of the command will be a number. It's automatically copied to the Clipboard. Please paste it into a reply.
The Terminal window doesn't show the output. Please don't copy anything from there.

Issue in Outgoing Payment Posting

Hi All,
I am facing a problem at one of my clients that they saved outgoing payment draft in october 2008 and now they are trying to post in nov 2008 with past posting date. System is giving an error message that the posting date is not in the range of permissible dates. I checked all posting periods and unlocked the oct 2008 posting period but still facing this issue. We are using 2007A PL30.
Kindly help me out with this.
Best Regards,
/Siddiq

Hi Siddiq,
you need to make sure that the period status of the period covering October is 'Unlocked'. Check all dates (posting/due/document) on the payment form & ascertain that the period range is unlocked.
You also need to check whether B1 will allow you to post transactions with an earlier posting date under the document settings.
Should you have different posting periods with different GL account determinaltion, you also need to check whether the gl accounts involved are active for that date range.
All the best,
kerstin

Mgcp outgoing issue

Similar Messages

Maybe you are looking for