Missing "Last configuration change at" into the config

On two Catalyst 3750 12.2.(25r) SE1
with the command "show run"
I don't see the info:
"Last configuration change at xx"
"NVRAM config last updated at xx"
I use the "normal command:
service timestamps debug datetime localtime
service timestamps log datetime localtime
service password-encryption
aaa new-model
aaa authentication login default group tacacs+ local
aaa authorization exec default group tacacs+ local
aaa accounting exec default start-stop group tacacs+
aaa session-id common
On all other switches with the same config i haven't this problem
IOS Bug?
Best Regards
Andrea

Great!
The clock was correct but the NTP server is not reachable (behind a Firewall)
I have removed the NTP server, until the FW permit the NTP Protocol.
Now all messages are written into the config
Many Thanks
Andrea

Similar Messages

Please ensure that the applicationhost.config file is correct and recommit the last configuration changes made

I am receiving event ID 5189 on Server 2008 R2, IIS 7.5. I experience this error across a number of servers, each of which is running only the default web site, but have 600+ applications running on the default web site. Each application
has its own application pool. My point is, the applicationhost.config is rather large.
I have seen a number of posts on this error message, but my issue itself seems to differ somewhat. I am aware of a similar post: http://social.technet.microsoft.com/Forums/en-US/3128ee93-1319-4cc2-9257-003512caf476/event-id-5189-microsoftwindowswas?forum=exchangesvrgeneral
which points to KB http://technet.microsoft.com/en-us/library/cc734988%28v=ws.10%29.aspx
However, in my case, it doesn't seem that the extreme measures for this resolution are required. The error usually indicates a corrupted applicationhost.config that must be manually fixed, or otherwise the WAS service needs to be restarted, or the
server itself, etc.
In my case, the issue can usually be fixed by an application pool recycle, or at worst a stop/start. I have an application which is sensitive to recycles, and so we do not have periodic recycle events configured for this application, which is the bulk
of the applications on the servers. It seems to me that this issue is usually caused by the application being in use when there is an applicationhost.config change.
For instance, we have one application that we deploy using msdeploy. We found that when we ran an installation for this application via msdeploy, we were receiving this event, and we would subsequently get 500 errors in the application (sometimes the
application pool corresponds to that which is identified in the event log, sometimes it doesn't).    It seems like applications that were being hit at the time the applicationhost.config was modified by msdeploy were affected. In an attempt
to correct this, we moved from msdeploy to a batch file containing appcmd commands. This also did not resolve the issue.
I have another application which is installed using PowerShell commandlets. We started to notice that this script also caused the issue to occur on occasion. As I continued to identify different processes that resulted in the same issue, I came
to the conclusion that this is likely due to any change in the applicationhost.config. I assume the issue is that the applicationhost.config is modified during a read operation to the file by the application pool, or WAS service, and that the recycle
event, which corrects the issue, forces a re-read of the applicationhost.config, resolving the bad-read issue.
Has anyone else experienced this, or do you have any recommendations? My current work-around is to not install any applications during peak hours, and performing an IISRESET after installs are completed, to ensure application stability.
Message              : The Windows Process Activation Service failed to generate an application pool config file for application pool 'myAppPool'. The error type is '7'. To resolve this issue,
please ensure that the applicationhost.config file is correct and recommit the last configuration changes made. The data field contains the error number.
Id                   : 5189
Version              : 0
Qualifiers           : 49152
Level                : 2
Task                 : 0
Opcode               : 0
Keywords             : 36028797018963968
RecordId             : 324108
ProviderName         : Microsoft-Windows-WAS
ProviderId           : 524b5d04-133c-4a62-8362-64e8edb9ce40
LogName              : System
ProcessId            : 0
ThreadId             : 0
MachineName          : MyComputer
TimeCreated          : 3/3/2014 9:03:24 PM
ContainerLog         : system
MatchedQueryIds      : {}
Bookmark             : System.Diagnostics.Eventing.Reader.EventBookmark
LevelDisplayName     : Error
KeywordsDisplayNames : {Classic}
Properties           : {System.Diagnostics.Eventing.Reader.EventProperty, System.Diagnostics.Eventing.Reader.EventProperty, System.Diagnostics.Eventing.Reader.EventProperty}

As an update to this issue, after doing some research, it appears the behavior is related to a new feature in IIS7 called Application Pool Isolation (http://technet.microsoft.com/en-us/library/dd163536.aspx).
This new feature prevents cross-application spillage by isolating the configuration for each application pool in IIS. So in reality, an application pool never actually reads the applicationhost.config - that is just a master file, and each time it
is update, it triggers a change to the individual application pool configuration files, located in C:\inetpub\temp\apppools.
We did try setting Advanced Settings > Disable Recycling for Configuration Change to true, but after an IIS reset we were still able to reproduce the issue - worse actually, because in our test program, which continually hits the web
service, and also continually makes apphost.config changes, when the two events collide, the 500.19 issue precipitates; but after an additional change to the apphost.config, it seems that the additional changes will actually correct the issue (seemingly forcing
another recycle, which is also how we resolve the issue manually); after making this setting adjustment, once the 500.19 issue precipitates, additional changes to the apphost.config does not correct the problem, only a manual recycle corrects it. This
is the recycling.disallowRotationOnConfigChange property of the app pool. We also set the setting for recycling.disallowOverlappingRotation to True as well, with the same result.
We ARE able to prevent this issue by setting the C:\inetpub\temp\apppools\myapppool\myapppool.config to read-only, but for obvious reasons, this is not a desired work-around.
It seems like what is happening is that any change to the ApplicationHost.config is resulting in each of the C:\inetpub\temp\apppools temp application pool config files being updated as well, in addition to triggering an application pool recycle. It
seems to me the desired behavior would be that these files are only updated if the applicationhost.config changes are specific to that application pool - but that doesn't seem to be the behavior.
After turning on failed request tracing, I was able to narrow the error down more:
ModuleName
AnonymousAuthenticationModule
Notification
2
HttpStatus
500
HttpReason
Internal Server Error
HttpSubStatus
19
ErrorCode
2147942413
ConfigExceptionInfo
\\?\C:\inetpub\application\application\web.config ( 9) :Failed to decrypt attribute 'password'
Notification
AUTHENTICATE_REQUEST
ErrorCode
The data is invalid. (0x8007000d)
This seems to be pretty static. Trying to look into possible causes of this issue.

"Configuration changed. Restart the system" and then reboot on startup.

I have disabled WiMax in BIOS setup and now my x121e doesn't boot at all - just says that "Configuration changed. Restart the system" and reboots. When i press F1 to access bios setup - nothing happens. CMOS reset didn't help/

In service center they said that motherboard is glitchy and needs replacement.
So it was a hardware fault.

Has anyone experienced text going missing after using Change All in the Find Font dialogue box?

I manage an artwork production studio and two members of staff have separately reported that when using the Change All command to substitute fonts in InDesign's Find Font dialogue box, some text disappears from their documents. All affected text is originally set in the same font, and most of the conversion is fine but a few instances of text are actually removed (not reflowed). In the latest reported case, only four or five instances of text were 'deleted' across two pages of a 20pp document.
I've found a link that refers to the same issue but it's unresolved (http://www.listsearch.com/InDesign/Thread/index.lasso?20041#last)
I haven't been able to replicate this behaviour but would be interested to know if anyone else has experienced it and if so, under what circumstances it can occur, and what work-rounds or fixes are available.
Applies to InDesign CS3 and CS4, have not tested with CS5 because we haven't upgraded yet.

Joel, I am having the same problem you described. I have read of similar posts on PrintPlanet.com. Someone there thought it was a different text engine or something in CS4 which may be causing the problem.
I don't know what causes this but I believe it can be traced to a previously created file in CS3 is saved as a CS4 document.
The fonts associated with this problem for me are always Gill Sans, Palatino and some form of Helvetica. There may be others but these are the ones we notice the most.
Today I worked on an InDesign CS4 file. When I opened it I was given a missing font warning. I went to Find Font and it was different typefaces of Gill Sans that was missing. When I changed the missing font to Gill Sans Regular entire lines of text disappeared. I closed the document without saving it and reopened it. I did the same thing in replacing fonts. This time no text disappeared. Not reflowed; not white; not hidden—gone.
This is what I have been seeing for the past few months. The disappearing text is random and cannot be duplicated, though fonts may disappear in some other place. You never know where text will just disappear.
The workaround I have found is to export your file to an INX document and reopen it in CS3. You have to replace all missing text before saving it as INX, though. To my knowledge CS3 has never had this happen.
The workaround, though it works for me, is annoying. I'd like to know what to do to resolve this issue. What's the use in having CS4 if you can't trust it completely.
I use a Mac running 10.6.3. I also have running Suitcase Fusion 2.

I would like to change the gmail address to our google domain. I changed it in the config file but nothing really chaged when I go to options.applications/mailto.

So I read that if go to about:config I could edit the mailto info. I did that restarted and it seems to stick. But when I to tools/options/applications everything is the same. I must be missing something. This is using win7 with admin login, but I really a MAC user trying to tweak my work desktop.
Thanks

So I read that if go to about:config I could edit the mailto info. I did that restarted and it seems to stick. But when I to tools/options/applications everything is the same. I must be missing something. This is using win7 with admin login, but I really a MAC user trying to tweak my work desktop.
Thanks

Archive command not backing up the config

I setup archive feature on our switch stack, thinking it will back up the full running config to an FTP server. The setup works fine when a write-memory is performed - the entire config gets sent to text file on FTP server. When it does a scheduled archive; however, the text file is virtually empty.
Here is the config:
Switch#sh run | beg archive
archive
path ftp://<server-ip>/A06_3750/$h-
write-memory
time-period 1440
Every 1440 minutes, my understanding is it would archive the config to the ftp server. Here is the text file it leaves instead:
! Last configuration change at 07:04:29 PST Sat Jan 29 2011 by user
! NVRAM config last updated at 06:52:01 PST Sat Jan 29 2011 by user
boot-start-marker
boot-end-marker
end
What am I missing here? Do I have to setup a kron job to run the "archive config" EXEC command?

Router#sh run | be kron
kron occurrence BACKUP at 20:45 recurring
policy-list BACKUP
kron policy-list BACKUP
cli sh run | redirect tftp://172.16.0.30/TFTP
Feb 15 17:45:59.800: IP: tableid=0, s=172.16.0.1 (local), d=172.16.0.30 (FastEthernet0/0.1), routed via FIB
Feb 15 17:45:59.800: IP: s=172.16.0.1 (local), d=172.16.0.30 (FastEthernet0/0.1), len 41, sending
Feb 15 17:46:02.425: IP: tableid=0, s=172.16.0.1 (local), d=172.16.0.30 (FastEthernet0/0.1), routed via FIB
Feb 15 17:46:02.425: IP: s=172.16.0.1 (local), d=172.16.0.30 (FastEthernet0/0.1), len 544, sending
Feb 15 17:46:05.425: IP: tableid=0, s=172.16.0.1 (local), d=172.16.0.30 (FastEthernet0/0.1), routed via FIB
Feb 15 17:46:05.425: IP: s=172.16.0.1 (local), d=172.16.0.30 (FastEthernet0/0.1), len 544, sending
Feb 15 17:46:09.425: IP: tableid=0, s=172.16.0.1 (local), d=172.16.0.30 (FastEthernet0/0.1), routed via FIB
Feb 15 17:46:09.425: IP: s=172.16.0.1 (local), d=172.16.0.30 (FastEthernet0/0.1), len 544, sending
Feb 15 17:46:14.425: IP: tableid=0, s=172.16.0.1 (local), d=172.16.0.30 (FastEthernet0/0.1), routed via FIB
Feb 15 17:46:14.425: IP: s=172.16.0.1 (local), d=172.16.0.30 (FastEthernet0/0.1), len 544, sending
Feb 15 17:46:20.425: IP: tableid=0, s=172.16.0.1 (local), d=172.16.0.30 (FastEthernet0/0.1), routed via FIB
Feb 15 17:46:20.425: IP: s=172.16.0.1 (local), d=172.16.0.30 (FastEthernet0/0.1), len 544, sending
Feb 15 17:46:27.425: %SYS-3-URLWRITEFAIL: redirection url write failed 'Timed out'
TFTP SERVER LOGS
Connection received from 172.16.0.1 on port 52956 [15/02 20:45:56.078]
Write request for file . Mode octet [15/02 20:45:56.078]
Using local port 1167 [15/02 20:45:56.093]
: rcvd 0 blk, 0 bytes in 1 s. 0 blk resent [15/02 20:45:57.093]
interstingly routers CPU goes up to 70%.
When i tried first time, i crashed my router and had to reconfigure again.
Thanks & Regards
Ahmed...
NOTE:dont look at debug time as i forgot to configure timestamp debug command after restoring my router config

Configuration archive after configuration change

Hello,
I'm assuming this can work with switches, routers, and controllers. I'm running PI 2.1 and am trying to get the configuration archive functionality working. I have both of these options checked under System Settings > Configuration Archive:
:: Archive configuration out-of-box
:: Archive configuration on receiving configuration change events
On the IOS device, these settings were configured for syslog/snmp:
logging buffered 100000
no logging event link-status
logging trap notifications
logging facility local6
logging source-interface Loopback0
logging <Prime IP>
snmp-server community ***** RW 13
snmp-server enable traps config
snmp-server enable traps syslog
snmp-server host <Prime IP> version 2c *****
I do not see any syslog messages in PI under alarms/alerts and the configuration never gets archived. I haven't run tcpdump yet to determine if PI is receiving these traps but I was hoping it was something simple I was overlooking. Thanks for any assistance that can be provided.

Thank you for the reply. To answer your question, yes. Community information matches with PI credentials.
I actually did get it to work yesterday. I did original testing on a 1921 router which is still not working, but when I tried configuring the same information on some switches (3750's) it worked. I thought routers would be configured the same - are there hardware limitations to this?
I look in the built-in CLI template 'Configure Logging' in PI and it only has switches and WLCs as available devices to push out to but I don't know what to make of it.

STMS Configuration - Change Virtual System with Real System

Dear all,
My system, if I go in the transaction STMS in DEV system, was configureted in the following way:
DEV => QA => PROD (Virtual System)
Now, I want to change the PROD Virtual System in PROD Real System.
How Can procede?
Can you explain step-by-step the process?
Because the system was configureted from other people, and I'm new to using the STMS.
Thanks in advanced for your help.
Best Regards,
Giulio

Hi,
After the planned system is physically installed it is time to replace the Virtual System with the realized system.
The procedure for the same is as under:
1) Delete the Virtual System from the transport domain
. Login into Transport Domain system client 000
· Using STMS got to Overview=> Systems
· Chose SAP Virtual System=> Delete (confirm)
· Distribute configuration change.
As soon as the configuration change is distributed, the virtual system is deleted. The import queue for this system in TMS disappears but it is available as import buffer at the operating systems level.
Now add the new (physical system) to the transport domain:
If STMS is configured as standalone system then first delete STMS configuration on PRD system
login into PRD system client 000. (delete STMS configuration if present.)
run stms -> it's ask for set up STMS -> click on other configurition (F6)
Target Host -> host name of domain controller ( host name of transport domain system)
System number -> Instance number of domain controller ( instance number of transport domain system)
Now,
Go to the Transport Domain Controller and accept the system. (As the import buffer is available at the operating system level, no change requests will be lost)
Distribute the configuration changes.
regards,
kaushal

Change Texts on the Submit Expense Report Screen

Hi all,
I've tried to introduce a text using new functionality provided in last upgrade "Change Texts on the Submit Expense Report Screen" in order to be displayed when an expense report is sent for approval, but it doesn't work.
Do you know if this functionality is working? If it is working properly, could you explain me how I have to configure this to display the text?
Thanks in advance for your help.

Hi Héctor,
just checked it in the test system - it works fine. Please note that these settings may be country version spesific. To change the text:
open the fine tuning activity 'Change Texts on Submit Expense Report Screen'
click 'Add Row' in General Use block - new row added and a country version can be selected (if active), this field can be also empty - then the entry is relevant for generic country version. Optionaly provide a description.
click 'Create and Edit Texts'. Here the user can define a disclaimer text per language using 'Add Row' and entering the language as code (EN, DE etc)
at the end of activity save the changes using 'Save and Close'
Depending on country version and logon language the travelelr will see now specific dissclaimer text.
Best regards,
Alexander

Value not reflecting into the transparent table when checked through se11

Hi friends. i am using the following code to add data to a transparent table already creted by me.Now i am adding data to it through a ABAP program.It is displaying the output when I execute it but the new record added in the program is not saved itno the table actually.my code is :
REPORT ZWRITE_DATA.
tables zlfa2.
move 'achal' to zlfa2-field_name_1.
update zlfa2.
select * from zlfa2.
write / zlfa2-field_name_1.
endselect.
the above code is not showing the value 'achal' in it.and also no error message is being displayed.

Hi,
Commit work saves the changes done into the database. Using COMMIT WORK statement in your program have below mentioned effect:
Calls the subroutines specified by PERFORM ... ON COMMIT
Executes asynchronously any update requests (see CALL FUNCTION ... IN UPDATE TASK) specified in these subroutines or started just before
Processes the function modules specified in CALL FUNCTION ... IN BACKGROUND TASK
Resets the time slice counter to 0.
Ensures that the locks of the SAP locking concept are handled in accordance with its SCOPE Parameter.
Executes a database commit on all database connections
Closes all open database cursors (OPEN CURSOR) on all database connections
Releases all database locks on all database connections
KR Jaideep,

Track configuration changes

Hi,
Can anyone help me to track the configuration changes made in the system. I know the transport number but I can't go to the screen where configuration changes were made.
I need this to update the configuration documents.
Any help would be appreciated.
Thanks

Hi,
Please check this in SPRO.
Please check whether you have authorization to display the configuration in Production server. if you don't have authorization than be in touch with basis guy.
Thanks
Sunil

Grid Console and Configuration Change Console?

I have installed Grid Console 10.2.0.5, and now I'm looking at the Configuration Change Console URL (http://www.oracle.com/technology/software/products/oem/htdocs/config_control.html) wondering if I also need to install this as well.
It appears that the Grid console has all the management packs in, so maybe the Configuration Change Console is a standalone product (i.e. I only want the change management side and not all of grid control?)
Can someone clarify if I'm correct in this?
Regards
Stuart.

Thanks. We are just a small IT shop (only 12 databases), so Grid Console and repository are on the same server. I take it that I could also install Configuration Change Console on the same server under a different Oracle home, and use the same grid repository for the Change Configuration Console?

Passing a Parameter to the Procedure and changing it in the Procedure

Hi all,
I am trying to pass a parameter to a procedure like this.
PROCEDURE FLASH_PHY
(date_begin IN DATE, date_end IN DATE)
IS
I am trying to do SELECT and INSERT based on the date range passed in the procedure as mentioned above. And I am trying to do something like this.
SELECT NVL(sum(charges),0),count(summary_balances_id)
INTO lnu_charges_6months,c_summary
FROM SUMMARY_BALANCES
WHERE period_begin BETWEEN ADD_MONTHS((date_begin), -6) -- AND ADD_MONTHS((date_end), -1);
UPDATE summary_balances
SET cummulative_charges_6mo = lnu_charges_6months;
how should I do this parameter change. Right now if I use this select statement than it does not return anything as the parameter is passed on the procedure level. I am under the impression that when you pass a parameter to the procedure like this you can't change it into the procedure.
PLEASE GUIDE. Thanks a bunch. I really appreciate it.

From what I understand your variables that are passed into the
procedure can be manipulated as local variable to the procedure.
Here is my interpretation of what your attempting to do:
create or replace procedure A (x in number) IS
yes varchar2(3) := 'No';
begin
dbms_output.put_line('Start value for yes:'||yes);
select 'yes' into yes from dual where x+1 = 2;
dbms_output.put_line('End value for yes:'||yes);
end;
Call the procedure called "A" passing in a "1".
EG:
BEGIN
A(1);
END;
Does this answer your question?
,Russ

How to Load Master data text Description into the Data Target?

Hi,
I have a Master data which is an ID, and the description for that ID is added as text description along with the master data.
The datasource is a flat file load, which has both the fields i.e. ID as well as the description along with many other fields.
I need to load the flat file without changing it, into the ODS.
Please suggest a way to load the description of the ID along with the ID into the ODS, and then further into the CUBE.
This description field should be available, while checking the contents of the ODS as well as the CUBE.

hi Srinivas,
Thanks for the quick response.
I actually have the flat file with the description within it.
I cannot make any changes to the flat file.
So, please suggest me accordingly.

SG 200-08 - configuration changes disappear on power cycling

it's my first smart switch, but i've set up a million routers, so i'm not a complete n00b.
the only change that survived power cycling is the change of default password that it forced me to do.
what am i doing wrong, or is the box defect?

You will need to save your configuration changes before exiting the switch. Below are the steps to do this taken from the Admin guide.
THANKS
Rick Roe
Cisco Small Business Support Center
Copying and Saving Configuration FilesThe
Copy/Save Configuration page enables you to copy files within the filesystem. For example, you can copy the Backup Configuration file to the Startup
Configuration file so that it will be used the next time you boot up the switch.
To copy a file to the Startup or Backup Configuration file:
STEP 1
Click Administration > File Management > Copy/Save Configuration in thenavigation window.
STEP 2
Select the Source File Name:
Running Configuration
—Current configuration, including any changesapplied in the current management session.
Startup Configuration—Configuration file type used when the switch lastbooted. This does not include any configuration changes applied but not yet
saved to the switch.
Backup Configuration—Backup configuration file type saved on the switch.
Mirror Configuration—If the Running Configuration is not modified for atleast 24 hours, it is automatically saved to the Mirror Configuration file type,
and a log message with severity level
Alert is generated to indicate that anew Mirror Configuration file is available. The Mirror Configuration file can be
used when the switch has problems booting with the Startup or Backup
Configuration file types. In such cases, the administrator can copy the Mirror
Configuration to either the Startup or Backup Configuration file type and
reboot.
STEP 3
For the Destination File Name, select the file type to be overwritten with the file
you are copying:•
Startup Configuration—Configuration file type used when the switch lastbooted. This does not include any configuration changes applied but not yet
saved to the switch.
Backup Configuration—Backup configuration file type saved on the switch.
STEP 4
Click Apply to begin the copy process.When complete, a window displays the message, Copy Operation Successful.

Missing "Last configuration change at" into the config

Similar Messages

Maybe you are looking for