Modify existing zone and zoneset members
can anyone help me or guide a best document to edit/modify the existing zone and zoneset through CLI in mds 9509 fabric switch
I am not able to see how to add and delete the members in existing zone in the document, can you tell below mention command is correct for adding new device alias in existing zone?
Ex:
zone name ZONE_VM000ESX_CX4480x01_AB vsan 100
device-alias CX4480x01_B3
device-alias VM000ESX_HBA1
device-alias CX4480x01_A3
above is the example i am taking to modify.
adding new member in the exisitng zone (below commands are correct?):
switch(config)# zone name ZONE_VM000ESX_CX4480x01_AB vsan 100
switch(config-zone)# member device-alias CX4480x01_A0
switch(config-zone)# exit
How to delete "device-alias CX4480x01_A3" member from existing zone?
after this how to edit the zoneset to see the modifications done on above zone to apply in zoneset?
Similar Messages
-
Good Day,
Just a basic question. We use 9509's and 9513's for our SAN configuration. If I rename either a zone or an active zoneset does this in any way disrupt the connections using the zone or the zoneset. I want to standardize the naming conventions for our systems to better identify what they serve.
Thanks
JeffreyI'm not sure you can just rename the zone and zoneset. I think you may have to edit the current zoneset and add in duplicate zones with the new name, then delete the existing zones, with the old name, and then reactivate the current zoneset to push the change out. As long as there is no change in zone membership, no connectivity should be impacted.
As for the zoneset name, you may have to create a duplicate zoneset with the new name, and all the zones...with the new names...then activate the new zoneset name. Again, this should cause no impact to existing connectivity since the zone members will not be changing.
Hope this helps,
Mike -
Modify existing rebate condition and exclusion
Hi
We are rebate agreements for customers. Currently I want to modify rebate condition in one of rebate agreement.
Scenario: let us June 10th 2010 onwards, the rebate % is 3% for Profit center 'xxxx' & customer 'yyyy' instead of 1%. And 3% needs to accrued on billing docs going forward. How to set up this.
I tried to modify existing rebate condition using VBo2 as follows: went into rebate agreement using VBo2, changed rebate % for condition record with effective from 06/11/2010 and Saved. problem when I ran VBOF program, system posted reversal accrual for old rebate condition 1%. Old condition record validity from 01/01/2009 Valid to 12/31/2011.
I have one more question. We want to set up rebate condition for all materials exclude some of them. we have thousands of materials for which we need to calculate rebates. but we want to exclude some materials in the rebate agreement. How to set up such exclus
any ideas really appreciated
thnxThe key of your condition table (the one supporting your condition record in the agreement) is evidently Profit Center / Customer. So for any combination of profit center and customer, you can maintain a rate and validity period.
You are attempting to maintain two separate records having the same key. As you have experienced, the system does not allow it.
The simple solution is to expire that rebate agreement and start a new one with the updated validity period and conditions.
As for excluding certain materials, you need a more detailed key in your condition table. Something else from the material master seems appropriateu2014Commission Group for example. Maintain commissionable materials in group 01 and non-commissionable ones in group 02. Then a key combination of Commission Group / Profit Center / Customer would work well for you.
Regards,
Ken -
GPO Security Zones and Content Ratings "Modify Settings" buttons are disabled
Task: Trying to modify a GPO so that specific users who logon to Remote Desktop Servers will have a lower Internet security level for Internet Explorer.
We have two Windows Server 2008 Domain Controllers, when I access the GPO using the Group Policy Management Console and Editor on either of the two Domain Controllers, then navigate to User Configuration > Policies > Windows Settings > Internet Explorer
Maintenance > Security > Security Zones and Content Ratings, the available "Modify Settings" buttons are both disabled.
I've read through several forum posts relating to this and the closest solution mentioned was to turn off IE ESC for Administrators on both Domain Controllers. I've done this and it nothing has changed as a result. Is there a way enable the "Modify Settings"
buttons, or is there another way to achieve the task mentioned at the top of this post?Hi,
We need to import these settings before we modify them.
To import security zones and privacy settings from our computer using IEM:
Click
Import the current security zones and privacy settings
To import content ratings from our computer:
Click
Import the current Content Ratings settings
Regarding how to configure Security Zones and Content Ratings, the following article can be referred to for more information.
Configure Security Zones and Content Ratings
http://technet.microsoft.com/en-us/library/cc772410.aspx
Best regards,
Frank Shen -
ASAP Is any Java libraries exist to modify Excel file and PDF file
Is any Java libraries exist to modify Excel file and PDF file. I know about the third party libraries like Apache poi and many more. But I want to know about java libraries not the third party tools.
Souvik_Software wrote:
I don't know what you guys want. I simply asked for a answer and because me want it urgently that is why I have written "ASAP". But I think you are more energetic in fighting not with the answer. Thanks for the help.By flagging it with words as "ASAP" and "Urgent" your are implying that your question is more important than other people's questions or that your time is more valuable than the time of people answering questions here. So you see, by doing so, you sound rather selfish.
But, the answer to the question in your original post is: "no, there are no classes in the core Java API that do what you want". Simple. -
Create job and modify existing jobs in OM
Dear all
how to create job and modify existing jobs in OM?
thanks
Jeeva[…] (as I understand it), pdf's are not a viable solution as these print jobs feature a very high resolution (1200 dpi).
I would expect the output from Finale to be mostly in the form of font characters—so a PDF you create by printing-to-file should be resolution-independent. If you have +Adobe Acrobat+, that can be verified quite easily in Document Properties, which will list all embedded fonts, but you should also be able to tell by zooming ’way in with Preview: if the score still looks sharp when greatly enlarged (and the file takes up less than a few hundred kilobytes per page), you can be sure it will print well on any suitable device. (If you print-to-file as PostScript instead of PDF, the resulting document can be downloaded directly into any PS printer, but it will likely be several times larger than a PDF version.) -
How to apply modified UI Defaults to existing forms and reports?
Hi all--
I've been struggling with UI defaults and after searching through posts in this forum, it doesn't look like I'm alone.
Is there a way to apply changes made to UI defaults to existing forms and reports? New forms and reports pick up the changes, but can they by applied retoactively?
Thanks in advance,
Dan KrautheimThanks for the update,
We have a develpment 10g AS environment setup made,
1) But we are really confused how to present the forms and reports.
We have around 250 forms and reports running on client/server architecture. All these forms/reports have been copied to a fileshare and access control is restricted by folder security.
2) How to deploy forms - entries within formsweb.cfg with Named Configuration sections.
3) How to deploy reports, as to were to copy the .rep files.
getting the following error
REP-110: Unable to open file 'Car_Readings.rep'.
while trying
http://kddsvr6.kddc.com:7778/reports/rwservlet?report=Car_Readings.rep&userid=username/passwd@db&desformat=htmlcss
Thanks in advance,
AJi -
Firm Zone and Trade off Zone in Scheduling Agreement
Dear All
Please explain in detailed the concept of Firm Zone and Trade off Zone in Scheduling Agreement, and it's effects in MRP run, i.e. If i take a MRP run for a material whci is having firm zone as 30 days and trade off zone as 60 days then what will be the result of MRP. The Material MRP type is VB
Thanks and Regards
ManojHi,
Firm zone is the time frame in which you cannot change your orders (schedule lines) that you have ordered from a vendor in any way (Date change nor quantity change).
Trade off zone is time frame within which you can make changes to your procurement proposals, these changes are acceptable from vendor's side.
These time frames are agreed with the Vendor and then inserted for each scheduling agreement in 'Additional data'.
For your example if you take firm zone 30 days and trade-off zone 60 days, the check starts from current day on which MRP runs. For exampe current day is 1st Oct, all the procurement proposals with delivery date within 30 days that is till 1st September are firm orders, which MRP will not change in any case (You can find such orders with * in front of them in MD04 list). Beyond 1st september they are in trade off zone, in which MRP can modify them.
MRP types (VB in your case) have no correlation with these zones.
Amit G -
Steps to to enhance the existing cube and get the data from r/3
I am at entry level.
if i want to enhance an existing cube and pull data from R/3 into the cube what are the main steps i do.
in my scenario - this is SD module. The infocude is custom cube(CONTRACT cube) . I have to enhance this existing custom cube with new info objects. The person who had created this cube years ago has used generic data source .
Please explain me the main stepd i need to do in R/3 till i get it to BIcheck if you can enhance the existing generic data source to bring data for new info objects or if those fileds are aleady existing in the data source - if existing, you will have to make changes only in BW side, if not, you will have to first modify the generic data source
if you have modified the data source, relicate data source at BW side
create new info objects and add those to cube > activate info cube
map the info objects with fields in data source > activate tranformation
test it by loading the data
now you will have to move these changes to produciton;
move the data source changes to R/3 production system (if applicable)
replicate data source in BW production system
move the BW transports to production system
you will have communicate to the uses that data will not avialable for some time or you need to reload data in cube in off business hours or on a weekend
delete data from info cube
initialize delta without data transer
do a full repair to the cube
now you can run delta on a daily basis
I hope it helps.
Regards,
Gaurav -
Modifying existing mail rules now even worse with Mavericks 10.9.1
Mail nightmares continue with Mavericks update 10.9.1 installed. In fact, the nightmare gets bigger. The story goes like this.
Prior to Mavericks, I created a stack of rules to move Mail messages from the Inbox to designated Mailboxes, e.g. messages from Friends would be moved to a Friends mailbox. Everything worked fine.
Along comes Mavericks, and when I Edit a rule to add a new recipient, and Apply that rule change to Move existing messages to another mailbox, messages would be Copied instead of being Moved, even though Move was the only action selected.
Now with Mavericks 10.9.1, nothing happens when I Edit an existing rule and then Apply the rule change to an existing message. The messae just sits in the Inbox and does not appear at all in the Mailbox I want to move it to.
How do I modify mail rules to move a message to another mailbox, then apply that rule modification to existing messages?Hi BG 29,
Unfortunatelly you are not the only one with this problem. I am in the same situation with the exception that once I create the rule the new incoming messages will go to the designated mailbox. If you want to create a new rule, the message will just copy, not move to the mailbox. I contacted Apple support and a representative called me back and asked me to do all kind of stuff, but no luck. I was hopping that the update to 10.9.1 will solve this, but again no luck. I gave up in trying....I am waiting for the next update and hope for the best. -
Problem in modifying existing records in dbtab
Hi Experts,
I am doing a report where I have created two dbtab's , one for data getting saved and
other for fetching data and modifying exsiting records..
For eg - let ZABC be the table where I need to insert or update records and ZXYZ is the table where
I need to fetch and modify existing records.
Now my probelm is :
In case of inserting new records (multiple records ) into my dbtab ( ZABC ) its working ,
but modifying existing records in another dbtab (ZXYZ ) its not wroking !! plz advice !!
If my select querry for modifying exsiting records is:
SELECT * FROM ZXYZ INTO TABLE ITAB WHERE MATNR EQ S_MATNR.
*****then its inserting a newline along with the existing records.
but when my querry is,
SELECT single * FROM ZXYZ WHERE MATNR EQ S_MATNR.
then its modifying the existing records, but only the first record.
Loop at itab.
if sy-tabix = 1.
zabc-matnr = matnr.
zabc-idnrk = idnrk.
zabc-budat = s_budat.
zabc-menge = menge1.
ZXYZ-menge = ZABC-Menge + MENGE1.
ZXYZ-BALC = ZXYZ-Menge - MENGE1.
ELSEIF sy-tabix = 2.
zabc-matnr = matnr.
zabc-idnrk = idnrk.
zabc-budat = s_budat.
zabc-menge = menge2.
ZXYZ-menge = ZABC-Menge + MENGE2.
ZXYZ-BALC = ZXYZ-Menge - MENGE2.
ELSEIF sy-tabix = 3.
zabc-matnr = matnr.
zabc-idnrk = idnrk.
zabc-budat = s_budat.
zabc-menge = menge3.
ZXYZ-menge = ZABC-Menge + MENGE3.
ZXYZ-BALC = ZXYZ-Menge - MENGE3.
ENDIF.
INSERT ZABC.
IF SY-SUBRC EQ 0.
MODIFY ZXYZ.
IF SY-SUBRC = 0.
MESSAGE : I002 WITH 'RECORD CREATED'.
ENDIF.
ENDIF.
Please advice
Karthik
Edited by: Karthik R on Aug 24, 2009 9:42 PMHi,
This is because in the second case you are not selecting records into an internal table.
As a result only the first record which satisfies the where condition is fetched.
Check if the program goes into the loop when you write second select query.
KR Jaideep, -
I've read some of the related threads concerning "custom login scripts, etc etc". Some of these solutions are really complex. I'm new to portal and need a cut and dry method of modifying the default "Welcome to Oracle Portal" inititial login screen, as well as the login page. I would simply like to modify the look and feel, import my own graphics, etc. To this point, I have seen no easy way to do it. PLEASE HELP!
I modified the existing login page and it worked instantly without restarting the services.
I too wanted to easily modify the default SSO login page to suite my company's look and feel. The easiest and quickest way for me to do that was to put a redirect on the default SSO login page to a login page that I created in Portal (using the built in Portlet Login). My only problem is that now when a user mis-enters their username / pass they do not get an error page but are redirected back to the login page. Also, keep in mind that if you use the redirect method, all applications using the SSO will have this login page. That is not desirable for most companies. -
Hi all,
My requirement is all ready existing idoc is their add to the new segments.Where is see the existing idoc and how modified it.
requirement:
Invoice is created in R/3 the outbound idoc is created. The idoc details contain the PO Order Number, PO Line Number, Shipment Number, etc., along with serial number detail has to be added. For serial number detail additional segment has to be created and added to existing idoc.
Create the new segment for serial number and add to the existing idoc. u201CIDOC BasicType:INVOIC02 and IDOC Message Type: INVOIC u201C .
please help me.
sreddy.
Edited by: SReddy on Sep 8, 2008 7:06 AMHi,
Refer to the following link,
[How to extend an existing IDOC!;
Regards
Natasha Garg -
How to modify existing concurrent program
I want to edit and modify existing pl/sql concurrent program.
what are the steps required to do this?Hi,
Pls keep in mind that modifying standard programs is not advisable. You will get SPAU (http://help.sap.com/saphelp_nw2004s/helpdata/en/c8/61ec66e33611d1954b0000e82de14a/frameset.htm) when you upgrade your SAP system. Try to make an own version and include as much as possible from the standard program.
Eddy -
How to modify existing code of SQVI report?
Hi Expert,
There is a SQVI report which has already been created but we need to change the one for new requirement.
is there any way to modify existing code for new requirement?
Can we edit in abap workbench?
Thanks & Regards
SavitaSavita,
You can not modify SQVI system generated code. You need to go to SAVI change mode and make modifications. If your requirement is a sort of additional fields or inserting come code into the program , then SQVI is not the choice. You need to use Infoset Queries (SQ03, SQ02, Sq01).
KJogeswaraRao
Maybe you are looking for
-
Since installing 10.7.3 my downloads say that I do not have enough space on my computer for the download. These downloads are never more that 200 megs or so and I have 270 gigs left on my hard drive. Somehow the remaining space on my hard drive is no
-
File path selected by the user!!! (File Download)
Hi, Does exist a component, code line or any thing which emulate the Windows option <b>SAVE AS:</b> when the user does right click, but using a button to do this? If somebody knows? I will appreciate it. Thanks in advance!!! Tokio Franco Chang
-
In Scott Kelby's Photoshop Elements 4 book, there is a technique described under the heading "Lessening Freckles or Facial Acne". (page 210 in first edition, November 2005) Briefly, it involves the following steps: (1) Duplicate the image (2) Apply b
-
Primary Index on CDHDR table not working
Hi Experts, I am accessing the Table CDHDR with following fields in the WHERE clause of the SELECT Query (For All Enrteis). OBJECTCLAS---- >'EINKBELEG' OBJECTID---- >Here I am passing Purchase order No TCODE---- >'ME21N' CHANGE_IND---- >'I' I haven't
-
Where is the connection information stored for Mac Remote Desktop?
I want to restore Mac Remote Desktop connection information from a Time Machine backup to a new Mac. On the new Mac, I've installed Remote Desktop from the App Store and installed all the files found in ~/Library/Containers/com.microsoft.rdc.mac fro