Moving an Apple RAID

I have an Apple RAID attached to a Dual-Core Intel Xeon running 10.4.11
I want to move this to another server, a Quad-Core Intel Xeon running 10.5.8
The RAID is connected by two Fiber Channels. So if I just move it to the new system, Have mount points created and bring up the system. Will it recognize the RAID and see it like on the first one? Is there any new configuration I need to do on the new system?
Thanks.
Pat.

Hi
+"Will it recognize the RAID and see it like on the first one?"+
It should do.
+"Is there any new configuration I need to do on the new system?"+
That depends on how you're connecting to the XServe RAID? If you're connecting it via the on-board NIC to the secondary NIC on your server then configure it accordingly. If you're connecting it to the network and it has an appropriately assigned (static) IP address or if it's simply getting an address dynamically, no not really.
What I would do is unshare current share points on existing server. Use RAID Admin to shut the XServe RAID down. Disconnect it. Move it (if it's being moved) to the new location. Connect it up and switch it on. It should appear on the new server's desktop. Define your shares and test. That should be it?
Tony

Similar Messages

  • Apple Raid Card: Raid-1 volume degrading

    Hello,
    I have 2 Raid-1 volumes running on a late 2009 mac pro with an Apple raid card. The second Raid volume has degraded now 3 times in the last 2 1/2 weeks. Raid utility is saying that the drive is damaged but when I shutdown, pull the drive out of the bay and push it back in and then restart it says that the drive is good. After assigning it as a spare the Volume rebuilds and lasts about a week until the same thing starts all over again. Perhaps the drive is somehow damaged but it seems more like a connection problem. If this is a familar issue to anyone and someone has a suggestion it would be greatly appreciated.

    Maybe you need to do a full surface scan for bad or weak failing sectors.
    Next time it drops out (or whenever you decide to remove it manually).
    Use Disk Utility to Initialize with Write Zeroes option. This takes several hours.
    If it completes without any error messages at all, it should then be good to use.
    If Bad Blocks are found, they will generally be spared out by this process, and the drive can be good to use for a while, but is likely to fail within 6 months. You should consider moving it to light-duty or occasional use, such as backups.
    Sometimes the Initialization will fail. If the drive is still under warranty, return it to the manufacturer for a refund/replacement. Original Apple drives have a one-year warranty, same as your Mac. Manufacturer warranties are often (but not always) 3 years or more.

  • HT201302 I am trying to copy photos from an iPad to a Mac Air, but iPhoto does not recognize them Do you have to use PhotoStream to do this. Please forgive the ignorance, but we have just started moving to apple products and I know nothing about them. Tha

    I am trying to copy photos from an iPad to a Mac Air, but iPhoto does not recognize them. Please forgive the ignorance, but we have just started moving to apple products and I know nothing about them. Do you have to use PhotoStream to do this?

    How did the photos that you want to copy off get on the iPad  ? To copy photos to your computer that were taken with the iPad, copied to it via the camera connection kit, or saved from emails/websites then see this page - on a Mac you should be able to use iPhoto, Aperture or Image Capture
    To copy photos that were originally synced from a computer you will need a third-party app on your iPad such as Simple Transfer which can copy them off via your wifi network. But as photos are 'optimised' when they are synced to the iPad, any that you then copy back to a computer may not be exactly the same as they originally were on your computer.

  • Apple Raid Card panic on Mac Pro Early 2008 after installing SSD as an enhanced JBOD.

    I recently installed a SSD drive in my Mac Pro to replace an aging, original boot drive.  I have an Apple raid card with 3 other hds attached - all in an enhanced JBOD configuration.  After installing the SSD from OWC (3G Electra SATA II Compatible) everything appeared to work fine.  But after 36 hours I received a apple raid card kernel panic alert.  See below for diagnostic crash log.  OWC support says that their drive should work fine - now I am not so sure.  Anyone out there with suggestions/solutions is most welcomed.
    Anonymous UUID:       83ADF2C8-4D41-D2EE-58C2-0CC4344DB0B4
    Sun Jan  5 21:18:46 2014
    panic(cpu 3 caller 0xffffff7f98b1441e): "AppleRAIDCard controller panic"@/SourceCache/AppleHWRaidDriver/AppleHWRaidDriver-401/Driver/Driver/Apple RAIDCard.cp:1018
    Backtrace (CPU 3), Frame : Return Address
    0xffffff8221563e30 : 0xffffff8017622f69
    0xffffff8221563eb0 : 0xffffff7f98b1441e
    0xffffff8221563ef0 : 0xffffff8017aada80
    0xffffff8221563f30 : 0xffffff8017aac522
    0xffffff8221563f80 : 0xffffff8017aac5f7
    0xffffff8221563fb0 : 0xffffff80176d6aa7
          Kernel Extensions in backtrace:
             com.apple.driver.AppleRAIDCard(401.0)[06045EA1-0404-36C3-9BE6-FE217DCD420C]@0xf fffff7f98b11000->0xffffff7f98b26fff
                dependency: com.apple.iokit.IOSCSIBlockCommandsDevice(3.6.0)[657BB360-C3EA-3D01-934E-12DBD6 0BBBF5]@0xffffff7f97f80000
                dependency: com.apple.iokit.IOPCIFamily(2.8)[447B4896-16FF-3616-95A2-1C516B2A1498]@0xffffff 7f97cba000
                dependency: com.apple.iokit.IOSCSIParallelFamily(3.0.0)[B6D80E76-647D-3BAE-823A-85871E9BAC7 2]@0xffffff7f97ca9000
                dependency: com.apple.iokit.IOSCSIArchitectureModelFamily(3.6.0)[76253A22-A1DB-3BF4-A972-E6 94A37CD09A]@0xffffff7f97c78000
    BSD process name corresponding to current thread: kernel_task
    Mac OS version:
    13B42
    Kernel version:
    Darwin Kernel Version 13.0.0: Thu Sep 19 22:22:27 PDT 2013; root:xnu-2422.1.72~6/RELEASE_X86_64
    Kernel UUID: 1D9369E3-D0A5-31B6-8D16-BFFBBB390393
    Kernel slide:     0x0000000017400000
    Kernel text base: 0xffffff8017600000
    System model name: MacPro3,1 (Mac-F42C88C8)
    System uptime in nanoseconds: 91308918786320
    last loaded kext at 89490169308794: com.apple.filesystems.smbfs          2.0.0 (addr 0xffffff7f99714000, size 335872)
    last unloaded kext at 1120636252260: com.apple.driver.StorageLynx          3.3.5 (addr 0xffffff7f99714000, size 8192)
    loaded kexts:
    com.apple.filesystems.smbfs          2.0.0
    com.apple.driver.AudioAUUC          1.60
    com.apple.filesystems.autofs          3.0
    com.apple.driver.AppleBluetoothMultitouch          80.14
    com.apple.iokit.IOBluetoothSerialManager          4.2.0f6
    com.apple.driver.AppleUpstreamUserClient          3.5.13
    com.apple.driver.AppleMCCSControl          1.1.12
    com.apple.kext.AMDFramebuffer          1.1.4
    com.apple.iokit.CSRBluetoothHostControllerUSBTransport          4.2.0f6
    com.apple.AMDRadeonX3000          1.1.4
    com.apple.driver.AppleUSBDisplays          360.8.14
    com.apple.driver.AppleHDA          2.5.3fc1
    com.apple.driver.AppleMCEDriver          1.1.9
    com.apple.kext.AMD5000Controller          1.1.4
    com.apple.driver.AppleLPC          1.7.0
    com.apple.iokit.IOUserEthernet          1.0.0d1
    com.apple.Dont_Steal_Mac_OS_X          7.0.0
    com.apple.driver.AppleHWAccess          1
    com.apple.driver.ACPI_SMC_PlatformPlugin          1.0.0
    com.apple.driver.XsanFilter          404
    com.apple.driver.Oxford_Semi          3.3.5
    com.apple.iokit.SCSITaskUserClient          3.6.0
    com.apple.AppleFSCompression.AppleFSCompressionTypeDataless          1.0.0d1
    com.apple.AppleFSCompression.AppleFSCompressionTypeZlib          1.0.0d1
    com.apple.BootCache          35
    com.apple.driver.AppleIntel8254XEthernet          3.1.3b1
    com.apple.driver.AppleRAIDCard          401
    com.apple.driver.AppleUSBHub          650.4.4
    com.apple.driver.AppleAHCIPort          2.9.5
    com.apple.driver.AppleIntelPIIXATA          2.5.1
    com.apple.driver.AppleFWOHCI          4.9.9
    com.apple.driver.AppleUSBEHCI          650.4.1
    com.apple.driver.AppleUSBUHCI          650.4.0
    com.apple.driver.AppleACPIButtons          2.0
    com.apple.driver.AppleRTC          2.0
    com.apple.driver.AppleHPET          1.8
    com.apple.driver.AppleSMBIOS          2.0
    com.apple.driver.AppleACPIEC          2.0
    com.apple.driver.AppleAPIC          1.7
    com.apple.driver.AppleIntelCPUPowerManagementClient          216.0.0
    com.apple.nke.applicationfirewall          153
    com.apple.security.quarantine          3
    com.apple.driver.AppleIntelCPUPowerManagement          216.0.0
    com.apple.kext.triggers          1.0
    com.apple.driver.IOBluetoothHIDDriver          4.2.0f6
    com.apple.driver.AppleMultitouchDriver          245.13
    com.apple.iokit.IOSerialFamily          10.0.7
    com.apple.driver.AppleSMBusController          1.0.11d1
    com.apple.iokit.IOBluetoothHostControllerUSBTransport          4.2.0f6
    com.apple.iokit.IOAcceleratorFamily          98.7.1
    com.apple.driver.DspFuncLib          2.5.3fc1
    com.apple.vecLib.kext          1.0.0
    com.apple.iokit.IOAudioFamily          1.9.4fc11
    com.apple.kext.OSvKernDSPLib          1.14
    com.apple.iokit.IONDRVSupport          2.3.6
    com.apple.iokit.IOFireWireIP          2.2.5
    com.apple.kext.AMDSupport          1.1.4
    com.apple.AppleGraphicsDeviceControl          3.4.12
    com.apple.iokit.IOSurface          91
    com.apple.iokit.IOBluetoothFamily          4.2.0f6
    com.apple.driver.AppleHDAController          2.5.3fc1
    com.apple.iokit.IOGraphicsFamily          2.3.6
    com.apple.iokit.IOHDAFamily          2.5.3fc1
    com.apple.driver.AppleSMC          3.1.6d1
    com.apple.driver.IOPlatformPluginLegacy          1.0.0
    com.apple.driver.IOPlatformPluginFamily          5.5.1d27
    com.apple.driver.AppleUSBHIDMouse          180.9
    com.apple.driver.AppleHIDMouse          180.9
    com.apple.driver.AppleUSBHIDKeyboard          170.15
    com.apple.driver.AppleHIDKeyboard          170.15
    com.apple.iokit.IOUSBHIDDriver          650.4.4
    com.apple.driver.AppleUSBMergeNub          650.4.0
    com.apple.driver.AppleUSBComposite          650.4.0
    com.apple.iokit.IOFireWireSerialBusProtocolTransport          2.5.1
    com.apple.iokit.IOFireWireSBP2          4.2.5
    com.apple.iokit.IOSCSIMultimediaCommandsDevice          3.6.0
    com.apple.iokit.IOBDStorageFamily          1.7
    com.apple.iokit.IODVDStorageFamily          1.7.1
    com.apple.iokit.IOCDStorageFamily          1.7.1
    com.apple.iokit.IOATAPIProtocolTransport          3.5.0
    com.apple.iokit.IONetworkingFamily          3.2
    com.apple.iokit.IOSCSIParallelFamily          3.0.0
    com.apple.iokit.IOSCSIBlockCommandsDevice          3.6.0
    com.apple.iokit.IOSCSIArchitectureModelFamily          3.6.0
    com.apple.iokit.IOUSBUserClient          650.4.4
    com.apple.iokit.IOAHCIFamily          2.6.0
    com.apple.iokit.IOATAFamily          2.5.2
    com.apple.iokit.IOFireWireFamily          4.5.5
    com.apple.iokit.IOUSBFamily          650.4.4
    com.apple.driver.AppleEFINVRAM          2.0
    com.apple.iokit.IOHIDFamily          2.0.0
    com.apple.driver.AppleEFIRuntime          2.0
    com.apple.iokit.IOSMBusFamily          1.1
    com.apple.security.sandbox          278.10
    com.apple.kext.AppleMatch          1.0.0d1
    com.apple.security.TMSafetyNet          7
    com.apple.driver.AppleKeyStore          2
    com.apple.driver.DiskImages          371.1
    com.apple.iokit.IOStorageFamily          1.9
    com.apple.iokit.IOReportFamily          21
    com.apple.driver.AppleFDEKeyStore          28.30
    com.apple.driver.AppleACPIPlatform          2.0
    com.apple.iokit.IOPCIFamily          2.8
    com.apple.iokit.IOACPIFamily          1.4
    com.apple.kec.corecrypto          1.0
    com.apple.kec.pthread          1
    System Profile:
    Model: MacPro3,1, BootROM MP31.006C.B05, 8 processors, Quad-Core Intel Xeon, 2.8 GHz, 18 GB, SMC 1.25f4
    Graphics: ATI Radeon HD 5870, ATI Radeon HD 5870, PCIe, 1024 MB
    Memory Module: DIMM Riser B/DIMM 1, 2 GB, DDR2 FB-DIMM, 800 MHz, 0x0000, 0x000000463732353642363145353830304600
    Memory Module: DIMM Riser B/DIMM 2, 2 GB, DDR2 FB-DIMM, 800 MHz, 0x0000, 0x000000463732353642363145353830304600
    Memory Module: DIMM Riser A/DIMM 1, 1 GB, DDR2 FB-DIMM, 800 MHz, 0x80AD, 0x48594D5035313241373243503844332D5335
    Memory Module: DIMM Riser A/DIMM 2, 1 GB, DDR2 FB-DIMM, 800 MHz, 0x80AD, 0x48594D5035313241373243503844332D5335
    Memory Module: DIMM Riser B/DIMM 3, 4 GB, DDR2 FB-DIMM, 800 MHz, 0x0000, 0x000000463732353142363445363830304600
    Memory Module: DIMM Riser B/DIMM 4, 4 GB, DDR2 FB-DIMM, 800 MHz, 0x0000, 0x000000463732353142363445363830304600
    Memory Module: DIMM Riser A/DIMM 3, 2 GB, DDR2 FB-DIMM, 800 MHz, 0x0000, 0x000000463732353642363145353830304600
    Memory Module: DIMM Riser A/DIMM 4, 2 GB, DDR2 FB-DIMM, 800 MHz, 0x0000, 0x000000463732353642363145353830304600
    Bluetooth: Version 4.2.0f6 12982, 3 services, 22 devices, 1 incoming serial ports
    Network Service: Ethernet 1, Ethernet, en0
    PCI Card: ATI Radeon HD 5870, Display Controller, Slot-1
    PCI Card: ATI Radeon HD 5870, ATY,LangurParent, Slot-1
    PCI Card: Apple RAID Card, RAID Controller, Slot-4
    Parallel ATA Device: PIONEER DVD-RW  DVR-112D
    USB Device: Hub
    USB Device: Keyboard Hub
    USB Device: Apple Optical USB Mouse
    USB Device: Apple Keyboard
    USB Device: XD-0405-U
    USB Device: Apple Cinema HD Display
    USB Device: USB2.0 Printer (Hi-speed)
    USB Device: Bluetooth USB Host Controller
    FireWire Device: built-in_hub, Up to 800 Mb/sec
    FireWire Device: unknown_device, Iomage HDD, Up to 800 Mb/sec
    FireWire Device: unknown_device, Unknown
    Thunderbolt Bus:

    RE: Mac Pro Replacement Graphics cards
    1) Apple brand cards,
    2) "sold in the Apple store" cards, and
    3) "Mac Edition" cards ...
    ... show all the screens, including Boot up screens, Safe Mode, Installer, Recovery, debug screens, and Alt/Option boot screens. At this writing, these choices include:
    1) Apple brand cards:
    • Apple-firmware 5770, about US$250** works near full speed in every model Mac Pro, Drivers in 10.6.5
    • Apple-firmware 5870, about US$450
    2) "sold in the Apple store" cards
    • NVIDIA Quadro 4000, about US$1200
    • NVIDIA Quadro 5000, about US$2500
    3) "Mac Edition" cards -- REQUIRE 10.8.3 or later:
    • SAPPHIRE HD 7950 3GB GDDR5 MAC Edition, about US$480** Vendor recommends Mac Pro 4,1
    • EVGA GTX 680 Mac Edition, about US$600
    The cards above require no more than the provided two 6-pin aux power connectors provided in the Mac Pro through 2012 model. Aux cables may not be provided for third-party cards, but are readily available.
    If you are Meet ALL of these:
    • running 10.8.3 or later AND
    • don't care about "no boot screens" etc AND
    • can re-wire or otherwise "work out" the power cabling, THEN:
    You can use many more cards, even most "PC-only cards"

  • Windows 7 Thunderbolt Apple RAID crashes?

    So Wndows 7 started getting CACHE_MANAGER BSODs, yesterday. They go away if ther LaCie Thunderbolt SSD is unplugged; configured the SSD as 2 disks instead of an Apple RAID seems to get rid of the problem as well.
    Given that there doesn't seem to be a way to install Windows on the SSD, I'd be reasonably content to disable Thunderbolt entirely for the moment; however, disabling Thunderbolt in the Device Manager does nothing.
    So any help disabling Thunderbolt or fixing the real problem would be appreciated.
    Thanks.

    Thunderbolt ports and displays: Frequently asked questions (FAQ)
    https://support.apple.com/kb/HT5219
    https://www.apple.com/thunderbolt/
    rMBP, Bootcamp off thunderbolt drive - MORE COMPLETE SOLUTION
    http://forums.macrumors.com/showthread.php?t=1414769
    https://discussions.apple.com/thread/4232557
    Boot Camp: FireWire devices may affect Windows 7 responsiveness if connected to an Apple Thunderbolt display
    http://support.apple.com/kb/TS4190
    This looks promising:
    http://www.macwindows.com/bootcamp5.html
    Thunderbolt problems with Windows 8
    TIP: Fix for Thunderbolt problem with Windows 8 in Boot Camp
    Boot Camp users who updated Windows 7 to Windows 8 may find that a Mac booted with Windows 8 does not recognize Thunderbolt . According to a new Apple tech article, the problem is an incompatibility with the Windows 8 Fast Boot feature (also called Fast Startup). The workaround is to disable Fast Boot using the Windows Control Panel.
    Here's how:
    In Windows 8, open the Control Panel. (You can move the mouse to the upper-right corner to activate the Charms bar, click the Settings icon, and then select Control Panel.) 
    Select Hardware and Sound. 
    Under Power Options, choose Change What the Power Buttons Do. 
    Under Shutdown Settings, uncheck the Turn On Fast Startup. Checkbox. 
    Click Save and then restart the Mac back into Windows.
    After restart, Windows 8 will recognize Thunderbolt devices attached to the Mac.

  • Windows and Mac Pro w/ Apple RAID card

    It happened i have a need to run Windows natively on Mac Pro with Apple RAID card installed.
    I know there is no Windows driver for that card, but i had a hope to bypass RAID card via connecting of internal SATA drive directly to iPass(SSF-8087) connector of Mac Pro's motherboard and using of that drive for Windows.
    So, i've connected SATA drive this way and it works fine with OS X.
    But i can't even try it with Windows because Mac Pro doesn't boot up from Windows installation CD if Apple RAID card installed
    Empty black text console is all that i've got after selecting of Windows installation CD in EFI boot menu.
    I need a suggestion how to bypass my problem, or generally speaking, how to install Windows onto Mac Pro with Apple RAID card.

    I've tried that.
    Installation and booting of WinXP passed OK if RAID card removed.
    But i've got black screen again trying to boot WinXP after RAID card re-installed.

  • How do I determine what needs attention on my Apple RAID card?

    Every time I turn on the computer, I get a message that says," The Apple RAID Card installed in your system requires your attention."
    This is what I have: RAID 065-7214 Mac Pro RAID Card
    Why do I keep getting this message? I am not sure what needs to be done to rectify any error. If there is no error and the warning is just due to battery charging, then I would like the warning to stop appearing--or do I just have to continuously click "Ignore"? Any insight into this?
    When I open RAID Utility it says: RAID set R0-1 has been mounted with indeterminate data loss. ( Is this just due to improper shutdown?)
    Also: Controller reports RAID system 72-hour battery reserve unavailable-System is configured to run without battery.
    Message was edited by: Darlyne

    I have had the exact same error message. When you open Raid Utility (that is where you can read what "attention" is needed you will see under the "Status" section what happened, and under the "Tasks" you will see the raid card "initializing" your RAID set. The first time I saw this I freaked, thinking that my drives were being reformatted, and my data would be lost. This is not the case. If you look down on the left side, you will (hopefully) see green lights next to your drives. The initialization seems to be a verification of the raid structure -- basically checking to make sure everything is redundant.
    So, back to the original question: it seems from my poking around that you SHOULD NEVER TURN OFF your Mac Pro with an Apple Raid Card installed. The firmware is not able to spin down the drives correctly, so when you turn your machine back on, you get the error message we have been discussing.
    I would recommend you get a good battery backup (UPS, like an APC) and just power off your monitor when not using your machine. I did not see this in the documentation, I am not 100% sure, but this is what I will be doing. In my case it takes many hours for the Raid Util to initialize my Raid again.
    Hope this helps.
    Theo

  • What's the difference in Apple RAID card battery error messages?

    I have a Mac Pro with 2 quad core Intel Harpertown CPUs at 3.2GHz, and an Apple RAID card.  RAID Utility shows that the battery failed but in my research, nobody explains the difference between "Battery failed (code 0x#0 = 17)" (which is what I have) and "Battery failed (code 0x#0 = 18)" or ""Battery failed (other than expired)" (the latter two are what everybody talks about) and what the code numbers mean.  Speaking to a local AASP, they recommend that I just wait for a couple of days to see if it's doing the automatic 72-hour reconditioning operation since my Mac Pro is attached to a pretty hefty UPS (2200VA with nothing else attached) and power failures where I live are rare plus the write cache has been disabled so the RAID card is basically doing write-throughs at the moment.  But curiosity about the various, different error codes and messages is getting the better of me.  Thanks in advance.
    Also, what's worrying me (since RAID Utility is so vague) is this entry I found under "Hardware RAID" in System Profiler:
      Status:
      Charging:          No
      Conditioning:          No
      Connected:          Yes
      Discharging:          No
      Sufficient Charge:          No

    As an update to this, once I replaced the RAID card battery (which was an absolute nightmare--the writer of the instructions at Apple obviously had never done it for real nor seen it done since they omit a lot of important things), the problem went away.  But I'm still intrigued about what the error codes mean.

  • Apple RAID card II - will it work in single CPU Mac Pro 4,1?

    Will the Apple RAID card work in a quad core 2009 Mac Pro?  I'm refurbing a used Mac Pro I got at a great price and just wondering if I can put in this card (which was "thrown in" with a used 8 core I also bought) with the idea of doing a RAID 10 to experiment with getting top disk read/write performance. I know most do not like the Apple RAID card II but it might be a cost effective way to max out performance on the single CPU, quad core Mac Pro. Ultimately I want to falsh the firmware to 5,1 and upgrade the CPU to a W3690 hex core. I plan to use this box for photography, light video and possibly sound editing. If my plan will result in high benchmarks and provide some fault tolerance I'm comfortable with using the card. I have heard from other users that the new card is much better than the first version and that it actually works pretty well. Any insights appreciated.

    Heck!
    Im about to win an eBay auction for a blue Apple RAID card together with a pair or SAS 300gb cheetah 15.5k discs for 75 bucks *happy*. Would have been healthy fast upgrade for small investment I thought?!
    Guess it probably would have been if the thing worked!?
    Why doesnt it work? iPass cable or something like that?
    Suppose I still want to go the SAS route with those drives for performance. Any other cards not too expensive that will enable SAS in the Pro?
    I use my MP 4,1 as a photo edit workstation but I also keep it on 24/7 for home server, web server, nas, backup etc. So i like to use items that are made for round the clock usage.
    Or i just get inexpensive SATA drives and SoftRAID them. So RAID 0+1 is no problem in software RAID?
    Thank you guy for quick informed response

  • Suggestions for removing Apple RAID Card?

    After a year of dealing with problematic Apple RAID cards, and replacement batteries – we are ready to move on, without the RAID card.
    We have not yet used it as a RAID – all drives operate discretely, non-RAIDed.
    We propose to remove the RAID card to eliminate that point of common failure. Has anyone else faced this, done this? Any suggestions, warnings?
    TIA for your kind attention.

    Hi Michael,
    What issues are you having? I had an issue with a faulty battery on a new xserve but once that was swapped out it's been as good as gold. If the drives you have installed have not been raided then you could buy the SATA backplane for the Xserve and swap it out.. Takes about 10 mins to do.
    All the best
    Beatle

  • Is there a firmware update for the Apple RAID Card [early 2009 Xserve] that will take it beyond the E-1.3.2.0 version and allow it to see 4TB drives?

    Is there a firmware update for the Apple RAID Card [early 2009 Xserve] that will take it beyond the E-1.3.2.0 version and allow it to see 4TB drives?

    I have a few of these RAID cards in a couple servers, and then I have an earlier version of the RAID card in a few different servers.
    The earlier servers are running non-apple 1.5 TB drives. It will be interesting to learn if this firmware update will indeed allow me to boost the capacity by installing non-apple drives, as the firmware previously has not.
    Ohh I'm excited to update and try! This will greatly help out if it does!

  • Installing Apple RAID Card on original Mac Pro 1.1

    After months of waiting, I finally received my ordered Apple RAID Card suggested by Apple Italia per upgrading my Mac Pro station to handle HD editing. OK. Great. the problem is that the inside of my Mac Pro does not resemble the illustrations in the manual and I can't find any instructions for mounting the card (it's the right one, on this site I found it and ordered the right one, the blue card) but I DON'T have the PCI Slider illustrated in the manual. Since you clame that I CAN install this RAID card (otherwise I wouldn't have bought it!) but I don't know if the absence of ANY sliding element in the place of the PCI Slider mentioned means that I have to connect wires, change the inside, go to an Apple Authorized Dealer (where I bought the thing!)? Can anyone help me?

    The instructions can be found here for the first generation Mac Pro:
    http://manuals.info.apple.com/enUS/MacPro_RAIDCardInstallation.pdf.
    Not sure what you mean by 'PCI Slider'. If you can reference the step this component is mention in the manual it might help.

  • 2010 Mac Pro with Apple RAID card - "Drive carrier 00:03 removed"

    I've got a 2010 Mac Pro with the Apple RAID card and 4 internal identical Seagate ST32000641AS 2TB drives inside.
    I've never had a problem with the RAID card (either battery or in operation) except for one thing:
    Almost every time I shut the machine down (which I try to do as rarely as possible), it keeps losing Drive 3, the spare.
    (See RAID Utility event log snippet below.)
    [I wish I could understand why this Apple RAID card keeps losing the spare across power-cycles/reboots, but I digress.]
    So I just adopted it as the spare and it spawns the rebuild and many hours later, everything's fine again.
    ... until the last time I rebooted (Jan. 2nd).
    After the usual "I lost the spare" message upon login, it began the rebuild.
    But this time, about 11 1/2 hours later the rebuild stopped and RAID Utility reported "Drive carrier 00:03 removed".
    Bay 3 is now missing in the Controller view.
    I powered off the system last night, and left it off overnight.  Today I took all the drives out, blew the dust off and reseated them.
    Same thing.  Drive 3 is still missing, and now the rebuild task aborted.
    The drive bay location shouldn't matter, right?  Can I swap the Bay 3 drive with the Bay 4 drive?
    I figure one of two things would happen:
    (1) It will report Bay 3 as being there but Bay 4 as being missing, same situation as is now.  Meaning the problem is in the Bay 3 spare drive.
    (2) It will report Bay 3 as being missing (despite a 'good' drive being present) and Bay 4 will be the (unattached) spare, and the RAID set will be unviable.  Meaning the problem is with the drive bay itself, not whatever drive is plugged into it.
    If "Drive carrier removed" is trying to tell me the disk is bad, why do I not see any log messages about it?  I suppose a spare that never gets used could go bad from lack of use, but ... no messages at all?
    Hesitant to plunk down $160 on a new spare disk if the present one isn't actually dead ...
    % sudo raidutil list raidsetinfo
                                         Total     Avail
    Raidsets      Type       Drives       Size      Size  Comments
    RS1           RAID 5     1,2,4      5.23TB    0.00MB  Rebuild: 0% complete            
    % sudo raidutil list driveinfo
    Drives  Raidset       Size      Flags
    Bay #1  RS1             2.00TB   IsMemberOfRAIDSet:RS1 IsReliable
    Bay #2  RS1             2.00TB   IsMemberOfRAIDSet:RS1 IsReliable
    Bay #4  RS1             2.00TB   IsMemberOfRAIDSet:RS1 IsReliable
    Event log snippet:
    Saturday, January 11, 2014 8:15:19 AM PT
    Background task aborted: Task=Rebuild,Scope=DRVGRP,Group=RS1
    informational
    Friday, January 3, 2014 3:50:28 AM PT
    Drive carrier 00:03 removed
    informational
    Thursday, January 2, 2014 4:29:37 PM PT
    Marked drive in bay 3 as a global spare
    informational
    Thursday, January 2, 2014 4:29:28 PM PT
    Adopted drive in bay 3
    informational
    Thursday, January 2, 2014 4:28:34 PM PT
    Degraded RAID set RS1 - No spare available for rebuild
    critical
    Saturday, December 7, 2013 5:35:17 PM PT
    Marked drive in bay 3 as a global spare
    informational
    Saturday, December 7, 2013 5:35:08 PM PT
    Adopted drive in bay 3
    informational
    Saturday, December 7, 2013 5:34:11 PM PT
    The "RedundancyScrub" command could not be executed. (Invalid request or invalid parameter in the request.)
    warning
    Saturday, December 7, 2013 5:34:03 PM PT
    Degraded RAID set RS1 - No spare available for rebuild
    critical
    Friday, December 6, 2013 4:56:47 AM PT
    Battery finished conditioning
    informational
    Thursday, December 5, 2013 9:53:44 PM PT
    Battery started scheduled conditioning cycle (write cache disabled)
    informational
    Friday, September 6, 2013 10:53:11 PM PT
    Battery finished conditioning
    informational
    Friday, September 6, 2013 3:41:33 PM PT
    Battery started scheduled conditioning cycle (write cache disabled)
    informational
    Saturday, June 8, 2013 3:41:35 PM PT
    Battery finished conditioning
    informational
    Saturday, June 8, 2013 8:37:49 AM PT
    Battery started scheduled conditioning cycle (write cache disabled)
    informational
    Thursday, May 30, 2013 4:09:51 PM PT
    Marked drive in bay 3 as a global spare
    informational
    Thursday, May 30, 2013 4:09:42 PM PT
    Adopted drive in bay 3
    informational
    Thursday, May 30, 2013 4:08:59 PM PT
    Degraded RAID set RS1 - No spare available for rebuild
    critical
    Thursday, May 30, 2013 3:32:29 PM PT
    Degraded RAID set RS1
    warning

    Power Pig wrote:
    "Hesitant to plunk down $160 on a new spare disk if the present one isn't actually dead ...
    % sudo raidutil list raidsetinfo
                                         Total     Avail
    Raidsets      Type       Drives       Size      Size  Comments
    RS1           RAID 5     1,2,4      5.23TB    0.00MB  Rebuild: 0% complete     
    I was talking about this.
    This looks like a RAID 5 setup without the parity to me. I would said it basically a RAID 0.
    Also you metioned "I guess that previous spare must really have gone 'bad', despite having never been used! "
    I wiped everything out, I selected the 3 disks and clicked on "Create RAID Set" with RAID5 selected and the "Use unassigned drives as spares" option checked.  The 3rd disk has always been marked as the spare ever since then.  You do not have a choice to create a "RAID5 setup without the parity".  If I wanted a RAID0 I would have chosen a RAID0!  raidutil now says
    % sudo raidutil list raidsetinfo
                                         Total     Avail
    Raidsets      Type       Drives       Size      Size  Comments
    RS1           RAID 5     1,2,3,4    5.23TB    0.00MB  No tasks running
    Every time the system would 'lose' Drive 3 on boot, I would just keep rebooting until it was 'found', and then manually re-assign the now-'floating' drive as the spare - and the RAID would rebuild.
    There was never a problem until the day that prompted this post - when it would not find Drive 3 no matter what I did.  I turned the Mac Pro off for several hours until the drives had all cooled down and it still did not find the drive.  I left the machine on but unmounted the degraded volume until I got the new replacement drive.
    I really don't understand what you are getting at. It's like you are trying to tell me I set it up as a 4-drive RAID5 with no parity(!) and that I was in grave danger because one of the disks was gone.  The actual RAID contents (spread across Drives 1, 2 and 4) were never in danger, unless a 2nd disk had failed while the spare was not seen by the Apple RAID card.  I wasn't too worried about that happening.

  • Good idea? . . . Moving the Apple Mail folder to your data volume

    Read the below quote from Mac Performance Guide. Is it a good idea? I know a bit of DOS, so I am used to command line commands but even after after Lloyd Chambers explanation, still not sure what is going to happen?
    ln -s /Volumes/Master/Mail Library/Mail
    The reason I want to move my Mail folder out of the home directory is because I plan to have a SSD as my boot drive and the home directory is on the boot drive, correct?
    "Moving the Apple Mail folder to your data volume
    This trick lets you move your Mail folder out of your home directory onto your data volume. I’ve used this technique for years so that I can forget about having to back up my home directory (default location for Apple Mail) and simply back up my one data volume: Master. The same trick can be used for any similarly irritating program that insists on storing its data in your home directory, rather than giving you a choice (a few programs are too brain-dead for this to work). Programs like iTunes let you choose where to put your music; use that option.
    Your Apple Mail folder is in the Library folder of your home directory.
    The trick requires starting Terminal. If that makes you uncomfortable, stop here! You are going to make a symbolic link.
    0. Quit Apple Mail, and make a backup of your mail folder.
    1. Copy the Mail folder to the top level of your data drive (or elsewhere, then modify step 3 appropriately).
    2. Rename the original mail folder to Mail.old as an additional backup.
    3. Start a Terminal window and type:
    ln -s /Volumes/Master/Mail Library/Mail
    This makes a symbolic link to the folder Mail on the volume Master (type the name of your volume, and use quotes around it if the volume name contains a space character). The resulting file Library/Mail is a tiny file that says “look over there on /Volumes/Master/Mail instead”.
    From here on out Apple Mail won’t know the difference! Launch Apple Mail and verify that it worked. If you encounter problems, simply copy your backup back into place."

    I just put the entire /Users/myaccount on another drive.
    Unlock Account control panel - advanced options -
    /Volumes/volname/Users/myaccount
    Move the whole enchilada instead of just mail. Definitely want to get Safari or web browsers cache which does a lot of I/O also. maybe put /Users on 2nd SSD or 10K VelociRaptor. Or just use your 640GB drive for /Users

  • Simple Apple RAID question...

    New MacPro, Apple RAID Card, 4 1TB drives, all included in the RAID 5 array that has been created and initialized in RAID Utility booted from the OS install disk. All looks well ATM.
    I now want to partition this array into two partitions. One 300 GB for OS/Apps, the other 2.x TBs for data. Someone mentioned I should partition using the RAID Utility, but can't figure out how to do this. Should I just be using Disk Utility to create the partitions on my new 4 drive, RAID 5 set?
    Thank you!! The RAID Utility user manual has no mention of this, and finding this answer on the internet is difficult.

    That explains the RAID setup, which I have created and successfully initialized. I never had the manual, but looking at it now that's exactly how I did it.
    Now that it has completed, I have a 4 disk RAID 5 "set", that is 2.x TBs in size, which is perfect. All I wanted to do was partition this set into two separate "volumes", just like you can do with any other "drive". I went into Disk Utility (booted to the install disk, the same disk that contained the RAID Utility), and created the partition in 2 minutes. I don't want to create two RAID sets, more drives in a RAID 5 set the faster, and didn't want to lose the HD space that 0+1 entails.
    I'm just wondering if this was correct, if doing it this way creates issues, etc...
    THANK YOU both for your responses!

Maybe you are looking for