MSE 3350 and WCS

Hi All,
I have the following getserver info from the MSE 3350,
The WCS ver. 7.0.172.0, the initial install documentation shows that the following ports needs to be opened on MSE to have successfull communications between WCS and MSE.
Can someone clarify this situation for me,.
1. From the MSE getserverinfo. the follwoing seems to be in "false" state.
HTTP : false
legacy HTTPS:false
but the communication between the MSE and WCS SOAP/XML needs HTTP/HTTPS opended.
Can I make any changes on the MSE through CLI to fix this issue. Unless this is not an issue.
2. I issued a netstat -tulpn command and I am not able to see certain ports not listening
Please see the attached text file.
Example :
TCP 443 for HTTPs
SNMP 161, 162
TCP 80
TCP 21 for FTP
TCP 16113 for MSE to WLC ( NSMP Protocol exchanges)
I am unable to see those.
Thanks
Let me know if this will cause an issue while i deploy the MSE into live production.

When you go throuh the script to install the MSE, it should ask you about using HTTP/HTTPS.
you can rerun the script from /opt/bin/setup.sh (please check my pathing on this)
HTH,
Steve
Please remember to rate helpful posts or to mark the quesiton as answered so that it can be found later.

Similar Messages

  • MSE 3350 is not come on GUI

    Hi
    I have configured MSE 3350 but it is unable to come up on GUI.
    Please help me to doing the initial troubleshoting.
    [root@Gig-1-MSE-1 ~]# rundiag
    11 Nov 2013 19:06:07,341 - ------------ Start Running Diagnostics --------------
    11 Nov 2013 19:06:07,346 - ------------ Start MSE diagnostics ----------------
    11 Nov 2013 19:06:07,433 - MSE Platform is down.
    11 Nov 2013 19:06:07,433 - ------------ End MSE diagnostics ----------------
    11 Nov 2013 19:06:07,433 - ------------ Start Location Server Info -------------
    11 Nov 2013 19:06:07,463 - Location Server is down.
    11 Nov 2013 19:06:07,463 - ------------ End Location Server Info ---------------
    11 Nov 2013 19:06:07,539 - ------------ Start /etc/hosts ----------------
    11 Nov 2013 19:06:07,545 -
    # /etc/hosts file generated by appliance setup
    # hostname=Gig-1-MSE-1
    # domain=uataxisb.com
    # eth0_ipaddress=10.101.2.8
    127.0.0.1               localhost.localdomain localhost
    10.101.2.8                Gig-1-MSE-1.uataxisb.com
    11 Nov 2013 19:06:07,545 - ------------ End /etc/hosts ----------------
    11 Nov 2013 19:06:07,545 - ------------ Start /sbin/ifconfig output ------------
    11 Nov 2013 19:06:07,557 -
    eth0      Link encap:Ethernet  HWaddr 34:40:B5:D7:9B:58
              inet addr:10.101.2.8  Bcast:10.101.2.255  Mask:255.255.255.0
              inet6 addr: fe80::3640:b5ff:fed7:9b58/64 Scope:Link
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
              RX packets:53618 errors:0 dropped:0 overruns:0 frame:0
              TX packets:4129 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000
              RX bytes:5778646 (5.5 MiB)  TX bytes:326864 (319.2 KiB)
              Interrupt:169 Memory:92000000-92012800
    eth1      Link encap:Ethernet  HWaddr 34:40:B5:D7:9B:5A
              BROADCAST MULTICAST  MTU:1500  Metric:1
              RX packets:0 errors:0 dropped:0 overruns:0 frame:0
              TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000
              RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
              Interrupt:130 Memory:94000000-94012800
    lo        Link encap:Local Loopback
              inet addr:127.0.0.1  Mask:255.0.0.0
              inet6 addr: ::1/128 Scope:Host
              UP LOOPBACK RUNNING  MTU:16436  Metric:1
              RX packets:72 errors:0 dropped:0 overruns:0 frame:0
              TX packets:72 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:0
              RX bytes:4932 (4.8 KiB)  TX bytes:4932 (4.8 KiB)
    sit0      Link encap:IPv6-in-IPv4
              NOARP  MTU:1480  Metric:1
              RX packets:0 errors:0 dropped:0 overruns:0 frame:0
              TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:0
              RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
    usb0      Link encap:Ethernet  HWaddr 36:40:B5:FC:89:FB
              BROADCAST MULTICAST  MTU:1500  Metric:1
              RX packets:0 errors:0 dropped:0 overruns:0 frame:0
              TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000
              RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
    11 Nov 2013 19:06:07,557 - ------------ End /sbin/ifconfig output --------------
    11 Nov 2013 19:06:07,557 - ------------ End Running Diagnostics ---------------
    [root@Gig-1-MSE-1 ~]#/etc/init.d/msed start
    Starting MSE Platform
    Flushing firewall rules: [  OK  ]
    Setting chains to policy ACCEPT: filter [  OK  ]
    Unloading iptables modules: [  OK  ]
    Starting Health Monitor, Waiting to check the status.
    Failed to start the MSE Platform.
    Starting Admin process...
    Started Admin process.
    why it is showing faild to start the MSE Platfrom.

    Hi,
    I have done all the excercise but still the probplem is same.
    even i have configured secondary MSE as like same.. it is not shown that messeage.
    [root@Gig-1-MSE-1 ~]# /etc/init.d/msed start
    Starting MSE Platform
    Flushing firewall rules:                                   [  OK  ]
    Setting chains to policy ACCEPT: nat filter                [  OK  ]
    Unloading iptables modules:                                [  OK  ]
    Starting Health Monitor, Waiting to check the status.
    Failed to start the MSE Platform.
    Starting Admin process...
    Started Admin process.
    [root@Gig-1-MSE-1 ~]# /etc/init.d/msed stop
    Stopping MSE Platform
    Flushing firewall rules:                                   [  OK  ]
    Setting chains to policy ACCEPT: nat filter                [  OK  ]
    Unloading iptables modules:                                [  OK  ]
    [root@Gig-1-MSE-1 ~]# /etc/init.d/msed stop
    Stopping MSE Platform
    Flushing firewall rules:                                   [  OK  ]
    Setting chains to policy ACCEPT: filter                    [  OK  ]
    Unloading iptables modules:                                [  OK  ]
    [root@Gig-1-MSE-1 ~]# /etc/init.d/msed status
    STATUS:
    Health Monitor is not running
    [root@Gig-1-MSE-1 ~]# /etc/init.d/msed start
    Starting MSE Platform
    Flushing firewall rules:                                   [  OK  ]
    Setting chains to policy ACCEPT: filter                    [  OK  ]
    Unloading iptables modules:                                [  OK  ]
    Starting Health Monitor, Waiting to check the status.
    Failed to start the MSE Platform.
    Starting Admin process...
    Started Admin process.
    [root@Gig-1-MSE-1 ~]# /etc/init.d/msed status
    STATUS:
    Health Monitor is not running
    [root@Gig-1-MSE-1 ~]#
    Please help on it.

  • Adding a secure WLAN - WISM and WCS

    I have a setup including a WISM and WCS which currently only runs a guest service using webauth to get online. The service (by request) is not secured over the air. I would like to implement a second SSID with security but before going the whole way with 802.1x I wanted to implement a half way house. Service will still only be a guest service but I want the air traffic secured.
    So I guess my options are WEP (forget it) or WPA/WPA2.
    My question is do I have to run this service with a shared secret that I then need to inform all users of in order for them to be able to connect to the service or is there a way to implement a WPA service that uses some kind of credential check against the already configured RADIUS (ACS) servers?
    And if this is possible I assume there is no longer need for a webauth as this just seems to duplicate the login process.
    Thanks for any pointers in advance
    Paul

    The best thing you can do is start with the Configuration Guides.  If you don't have a test environment and have SMARTNET on the WiSMs/ WCS, utilize TAC to help you get up and going.  I would also suggest utilizing a Cisco Partner to help with the initial implementation as well.
    I would recommend upgrading your WiSMs and WCS to the latest versions and making sure configurations are the same across modules.  I upgraded our WiSMs from 4.x to 7.0.98.0 and WCS to 7.x.  Ran into a bug here and there but that is expected.  Just make sure the wireless devices support those versions.  If you are unsure, you can always work towards the AssureWave tested code.  WCS 7.x should be backwards compatible (check the release notes just to verify).  The Design Zone and Release Notes are your friend too.
    -Rick

  • Cisco CSM and WCS on same server

    Hi,
    Currently we are running Cisco CSM and Cisco WCS applications on different servers.
    Please let me know can it possible to install Cisco CSM and Cisco WCS on one server.
    Regards,

    As per their datasheet, both CSM and WCS support VMware or can run as virtual servers. So it should be possible to implement both as virtual servers and run on the same physical server.

  • 1230 Series LAP and WCS 6.0.199.0 Heatmap Problem

    I recently upgraded from WLC 4.2.207.0 to 6.0.199.0 (WiSM), and WCS 5.2.130.0 to 6.0.196.0. All my heatmaps that contain 1231G LAPs are solid "maroon" (-35 dBm) in color. If I remove the 1231 APs from the heatmap selection on the right hand side, my coexisting 1131 and 1142's display their heatmaps properly. My maps are all CAD format (dwg) converted to .png's using WCS. My goal is to migrate to 802.11n in small steps which our Cisco rep said we could do. Any ideas?

    Unfortunately, this is a bug in 6.0.199.0.  The "fix" is to upgrade to 7.0.98.0 or 6.0.199.4.  As you figured out, it only affects 1230 series APs, and only on the 802.11b/g side.  Bug ID was
    CSCti05687
    Incorrect power unit was used on AIR-AP1231G-A-K9 and IR-AP1220-IOS-UPGRD.

  • 802.11 n support in Wism and WCS

    Is the new wless standard 802.11n is supported in current shipments of Cisco WLC 44XX and WiSM ( 6500 wireless controller card) ?
    Also I need to know whether is is supported in WCS 4.1 ?

    Hi Nalaka,
    Yes, 802.11n is supported on the WISM and WCS starting with the following releases in the 4.2 train;
    Release Notes for Cisco Wireless LAN Controllers and Lightweight Access Points for Release 4.2.61.0
    http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn4200.html#wp302677
    The following new features are available in WCS 4.2.62.0
    802.11n support-The introduction of the Cisco Aironet 1250 series access point, a business-class access point based on the IEEE 802.11n draft 2.0 standard. The access point offers combined data rates of up to 600 Mbps to meet bandwidth requirements. Cisco WCS display screens include a listing for configuring, managing, and monitoring 802.11n access points and their associated wireless LAN controllers.
    The newest WLC and WCS 5.0 trains are now released as well :)
    Hope this helps!
    Rob

  • 2 4404's and WCS how to add an addition 4404

    We have two 4404's and WCS. The 4404's are almost maxed out. We have an addition 4404 which we would like to add to the group of 4404's. What is the best way to do this?
    Thanks

    If both on-line 4404 share the same configs (particulary the SSID and other stuffs) then copy the config into the new one (make sure the new one is off-line so IP addresses won't clash).
    Change the IP addresses of the new 4404.
    Add into WCS.

  • WLC and WCS licenses

    How many APs does wireless controller 5508 and WCS (version 7.0) supports?
    Cheers,

    Sorry for jumping in on the question with another question but it seemed the right place.
    I have an AIR-CT5508-25-K9 WLC and +25AP license : L-LIC-CT5508-25A.
    As far as I understand it the WLC should already have a 25AP license installed and with the adder license I should have a count of 50 APs.
    However, after installing the adder license the count is still 25.
    Could you please let me know if it's just something wrong in my reasoning or should a case be opened?
    Thank you,
    Barbara

  • Lms3.2 and wcs

    Sir:
    I want to install LMS3.2 and WCS in one server,but coundn't install both.
    Can I do so?

    I see
    Thank you！
    I stop the LMS’s service then can install the WCS,
    But when I started the LMS's service, the WCS cann't be started.
    infor:
    Starting WCS
    The Cisco Wireless Control System (4.2.62.11) service is starting...
    The Cisco Wireless Control System (4.2.62.11) service could not be started.
    A system error has occurred.
    System error 1067 has occurred.
    The process terminated unexpectedly.
    Failed to start WCS server.

  • Cisco BE6k with CUCM 10.X integration with Siemens with Hipath 3350 and 3550

    Dear Experts;
    We have one requirment from customer.
    They have 4 branches with Siemens Hipath 3350 and 3550  PBX and they want to integrate with cisco CUCM 10.x.
    The Head Quater with complete CUCM as IPT and branches with with Hipath 3350 and 3550  PBX.
    CIsco TAC says interoperability doc is not available and also I can see tehre is no doc.
    TAC Reply  As below.
    We do not have any documents about CUCM integration with Hipath 3350 and 3550 on our interoperability portal. This means that their integration with CUCM was never properly tested. So we can not confirm that all features will be working. But from CUCM perspective this is third-party device that can be integrated using SIP or ISDN (with Voice Gateway between them).
    Link for interoperability portal:
    http://www.cisco.com/c/en/us/solutions/enterprise/interoperability-portal/networking_solutions_products_genericcontent0900aecd805b561d.html#callmgr10
    Regards
    Debashis

    If the Siemens supports SIP or H323 you can attempt to simply create a trunk between the systems and route calls via it.  If IP integration is not an option then as pointed by TAC integrate via PRI circuit (preferably QSIG). From CUCM side it will be just another GW, similarly from Siemens side.  You'll need to select which side is going to be ISDN network (I always use Cisco side) and then make the other side user.

  • Vlan management with WLC and WCS

    I'd like to know if it is possible to use the same vlan for the management of the WCS and for configuring a wlan?
    I try to make this lab and when I declare a dynamic interface that is in the same subnet as the WCS ip address, the reliability between controler and WCS is lost.

    I know that I should not put servers on the same vlan as wireless client but I just want to know if it is possible or if Cisco implemented something to avoid this to understand why my lab didn't work with this configuration.
    Thanks

  • WLC, WCS and WCS Navigator

    I would like to know what is the difference between the Wireless Lan Controller and the Wireless Controller System.
    Need I WLC if I want deploy WCS.
    Can I use WCS without Wireless LAN Controllers?.
    What is the diference between WCS and WCS Navigator?

    You don't need a WCS server however you will require WLC's to control your Wireless WAP's. The WCS allows you to add multiple WLC's into one view along with floor plans and floor layouts and alerts. Without a WCS server you would have to manually login to each WLC controller to see what the WAP's are doing. It really depends on how big your site is and how many WAP's you have to deploy after a site survey is done.

  • What MSE 3350 versions are compatible with PI 1.4.0.45?

    Sounds simple, but on CCO the latest MSE version I see listed for the 3350 is 7.3.101, and its release note compatibility matrix only says 1.2.0.103. Is the 3350 no longer supported with PI 1.3 and above?

    Thanks, that looks promising! I had looked at http://www.cisco.com/en/US/customer/docs/net_mgmt/prime/infrastructure/1.4/release/notes/cpi_rn_14.html#wp103402
    which seems to suggest the 3350 will not work with PI 1.4.

  • MSE added to WCS, cannot assign services to controller

    I have a 30 day trial license of WCS and have added my WLC controller and APs.
    I installed the new MSE virtual appliance and added it to the WCS, it shows up fine however I see no services.
    When I SSH to the MSE and do a /etc/init.d/msed status I see that the CAS is up and running!
    However when I try to synchronize services and add mobility services to a controller CAS is greyed out and won't let me check it
    Where should I go from here?

    Hello Pavel,
    I can provide some background for what you've faced - it's on my blog to-do list, but hasn't come out yet to have helped you.
    There was a change in the internals of User-UserGroup relationship handling between XI Release 2 and XI 3.x.
    Previously, the relationship was exposed via the SI_GROUP_MEMBERS property for the UserGroup InfoObject, tied to the Users property in BIPlatform Web Services.
    Now, the SI_GROUP_MEMBERS is read-only, listing all the members, but trying to change the value using getUsers() is ignored.
    New properties (all properties named SI_ENT_* for both User and UserGroup, check the Query Builder for their names) have been defined for User and UserGroup InfoObjects, specifically for Enterprise authentication UserGroups.  This is to separate the handling of Enterprise UserGroups from those created for third-party authentication UserGroups (such as Windows AD user groups), such that you can add/remove memberships only for Enterprise UserGroups.
    The Enterprise SDKs have been modified internally to make this change invisible when migrating from XI Release 2 -> XI 3.x.
    However, since the BIPlatform Web Services work more directly with the InfoObject properties (via the BIAR API), it exposes the SI_ENT_* properties explicitly.
    The gist is that, to affect User-UserGroup memberships, you have to use the getEnt*() methods for either User or UserGroup.
    Sincerely,
    Ted Ueda

  • How to create guest access in wireless by WISM and WCS and ACS?

    dear sir
    i neeed to know the steps of how we can make guest access to our network like hotels by using our WISM v 7.0.220 and wireless control system and ACS ?

    You need to define your requirements a little bit. The WLC can do WebAuth and an employee can access either the WLC or WCS to put in the username and password credentials, but you would need to figure out what's best for you.
    Here is a support doc that you can reference.
    https://supportforums.cisco.com/docs/DOC-13954
    Sent from Cisco Technical Support iPhone App

Maybe you are looking for