My internet works fine with my wired cable modem, but when i connect to my extreme base station and setup my wireless network the internet no longer works and my apple tv by default

my cable modem works fine, but when I hook it up to my extreme base station and run through the prompts and set up my wireless network it doesnt work and neither does my apple tv by default. I am unsure how to correct this problem. It will come up saying that I dont have an IP address when I have it set to DCHP so I dont know what the problem is.

Push the reset button on the modem and power the modem off
Power off everything else....all devices....order is not important
Wait 15-20 minutes or longer
Connect the Ethernet cable from the modem to the WAN port (circle of dots icon) on the AirPort Extreme
Power up the modem and let it run for 5 minutes by itself
Power up the AirPort Extreme and let it run for 5 minutes
Power up each other device one at a time a few minutes apart
Check the network

Similar Messages

Our airport extreme network works fine with our 6 devices. But when someone comes over and tries to log on, they can't until we restart the airport. Then they can get on, but it knocks one of our devices off the network. Any ideas?

Our airport extreme network works fine with our 6 devices. But when someone comes over and tries to log on, they can't until we restart the airport. Then they can get on, but it knocks one of our devices off the network. Any ideas?

I have not done a factory reset, I was trying to find out if I had some setting configured wrong first. I figured I'd just make things worse if went through a reset!
Here is a couple of screen shots:

Multipmultiple Airport Extreme Base Stations: WDS Or "Extend Wireless Network" To Have Wired -- Wireless Bridge?

Hello there!
I've been looking for this info, but have as yet been unable to find it. Here's my scenario:
I have two Airport Extreme Base Stations (both are dual band) and 3 airport expresses. The main internet connection in my house is in one room, where I have an AEBS as the main wireless router. In another room, I have a bunch of ethernet-only devices. I'd like to use the 2nd AEBS in this room, plug the ethernet devices into it and have the 2nd AEBS act as a wired <--> wireless bridge (connected to the same wireless network as the 1st AEBS). I've attempted this via "extend a wireless network," but the ethernet devices don't get past the AEBS they're plugged into. Should I instead be implementing WDS?
I mention the airport expresses as I'd like to have airtunes & wireless signal in other areas, but would like to keep the set-up as simple as possible (i.e., not config the AXes for WDS unless it's required).
Thanks in advance for any help!

Unlike the 802.11n AirPort Express Base Station (AXn), the 802.11n AirPort Extreme Base Station (AEBSn) cannot be configured as a wireless Ethernet bridge.
However, there are at least two ways to configure it to provide wired clients access:
Connect the second AEBSn back to the first by Ethernet; reconfigure the second AEBSn as a bridge and disable its wireless radios, or
Reconfigure both AEBSns into an extended wireless network. For 802.11n AirPorts, this would be called a dynamic WDS. The AEBSn, connected to the Internet would be the "main" base station and it would only require that you enable the "Allow this network to be extended" option in the AirPort Utility. The extending AEBSn would need to be configured with the option, Wireless Mode = Extend a wireless network, enabled.
In both configurations, the second AEBSn's Ethernet ports would be enabled for wired clients.

I just created a new profile/user on my MacBook Pro. My pointer/mouse. It works fine in my older user profile, but when I go to the new profile my mac will not respond to clicks. Mouse moves but will not click. Already tried restarting and the pram zap.

I just created a new profile/user on my MacBook Pro. My pointer/mouse on my trackpad. It works fine in my older user profile, but when I go to the new profile my mac will not respond to clicks. The Mouse moves but will not click. Already tried restarting and the pram zap. The problem starts when I log out of my main profile. I get to the login screen and my laptop stops responding to clicks. When I manage to make my way back to my main profile the mouse works perfectly. Should I just delete the new profile and try again?

If the modem is also a router, either use the modem in bridge and run pppoe client on the TC.. that is assuming ADSL or similar eg vdsl. If it is cable service.. and the modem is a router, then bridge the TC.. go to internet page and select connect by ethernet and below that set connection sharing to bridge.
Please tell us more about the modem if the above gives you issues.

HT4623 I have an iPhone 4S that i dont use anymore. It is locked with a password & i can't remember the password. i am wanting to let my child use this phone now but when i connect it to my computer it says that it cannot find the device driver. How can i

I have an iPhone 4S that is locked with a password & cant remember password. when I connect to my computer it says that it cannot find the device driver. How can i fix this?

Hello jlb1977,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
iOS: Forgotten passcode or device disabled after entering wrong passcode
http://support.apple.com/kb/ht1212
place the device in recovery mode and restore it to erase the device:
Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to shut down.
While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
Continue holding the Home button until you see the Connect to iTunes screen.
iTunes will alert you that it has detected a device in recovery mode. Click OK, and then restore the device.
Best of luck,
Mario

Strange behaviour of HDMI: with most tv's works fine, with LG I get video, but no sound.

HP dv6 with an ATI HD 5650. With most Tv's ,the notebooks works great when connected trhough HDMI. But with my LG tv, I dont get sound (video is perfect). Same LG tv works perfect with other notebooks. I have tried different cables, reinstalling drivers, and of course configuring Playback to HDMI as default. I have spent hours with HP support but they think its a compatibility issue.

I have done the changes. The DVD in PAL format works (video and audio).
However, in my opinion a user should get a warning about the standard discrepancies when iDVD starts and not wait until a burn process starts. Moreover, I think iDVD should not lose any information by the import of iMovie projects depending on the project settings (preferences), since a user can always switch between PAL and NTSC.
Anyway, thanks so much for your help!
Juergen

I recently upgraded my OS to Lion 10.7.4. I also just upgraded from a 1st Generation Time Capsule to a 4th Generation Time Capsule. I have an Airport Express (Version A1264) that I formerly used to extend my wireless network. AE no longer works.

I recently upgraded my OS to Lion 10.7.4. I also just upgraded from a 1st Generation Time Capsule to a 4th Generation Time Capsule. I have an Airport Express (Version A1264) that I formerly used to extend my wireless network. Airport Express no longer connects to my network. I have downloaded Airport Utility 5.6 to try and configure, but with no luck.

TC first gen was not simultaneous dual band. So.. it's probably best to factory reset your extreme and then tell it to extend again.

Java is not working with Firefox 4.0. It was working fine with Firefox 3.6

When uploading photos on Zenfolio, Java was working fine with Firefox 3.6. But when I upgraded it to Firefox 4.0, Java stopped working properly. When I try to upload photos, the Java text opens up with all the programming codes. With Firefox 4.0, I am not able to upload photos into Zenfolio.

Please read this thread:
http://support.mozilla.com/bs/questions/797708

TS1398 3GS IPhone will not recognize a Wi-Fi connection at home or work. We have tried turning it on/off as well as turning airplane mode to on while turning it off then back on again. My 3GS IPhone is working fine with our router at home. Thanks

My husband's 3GS IPhone will not recognize a Wi-Fi connection at home or work. We have tried turning it on/off as well as turning airplane mode to on while turning it off then back on again. My 3GS IPhone is working fine with our router at home. Please advise what our next step should be. Thank you for taking the time to read this post!!

Just to double check you tried eveyrthing take a look at this link http://support.apple.com/kb/TS1398 .
Can also try powering off the home router, then the phone, and then power up the router wait for the signal and then power up the phone and see if he can connect.

2 airport extreme base stations later and still no internet connection-

Sorry - yet another beginner with internet connection troubles! (I have read all the posts I could find relating, but without any help).
I have had a Demon broadband account now for about a month (I’m in the UK) and in that time I have purchased a D-Link DSL-300T Ethernet modem and an Airport Extreme Base Station. I got wireless internet working relatively easily – with a powerful range over the whole house and garden, but then one Sunday night, the internet connection via the base station suddenly ‘died’.
I spent the following 3 days scrutinising all of my settings of both the Modem and the Base station, re-setting both, and bought new Ethernet cables / micro filters etc but with no luck. (I’ll point out at this stage that my broadband account is still active, and if I connect the Ethernet modem directly to my iBook [wired] I can still get my broadband connection. Alternatively, I tried daisy chaining the modem to the base station and then via an Ethernet cable to an iBook, but no connection could be made).
When wireless, Airport Admin recognises there is a modem there, and under preferences > network under Airport it states I am connected to the internet – but I’m not.
I then phoned D-Link and they confirmed my firmware was up-to-date for use with Apple products and talked me through all of the modem settings and tweaked a few things, but there was still no connection to the base station. I then phoned Apple. They were incredibly helpful (as ever) and after 35 min. came to the conclusion the base station might not be re-setting itself properly. The replacement one came yesterday, and again I spent a number of hours trying to get it connected to the internet, but there is still no internet connection via airport and I can confirm this from both my eMac and iBook.
Reading through the forums on here, I understand that my particular modem is problematic with the base station, but I can’t work out why it use to work and now it doesn’t! One theory I have investigated is that the firmware of the base station is two advance for the modem following an update, but after reinstalling the original firmware I started with, I still have no luck.
- The eMac is running 10.3.9 / iBook is running 10.4.3. The base station is reinstalled with the latest firmware via system update. The first base station and the modem were delivered to me 31/10/05.
Any help or suggestions would be really appreciated if anyone has any ideas
Thanks for your time
Will.
UK.

http://discussions.apple.com/thread.jspa?threadID=2316
78&tstart=0
I think if you follow the instructions I gave in this
link you will be fine.
Remember, If you for any reason loose your
connection, it is normally always a Power Issue..Your
ISP is down for service ..or some other anomoly, If
you were good before your settings will still be
good...Good Luck...Don
Hi Don,
Thanks for you quick response. I printed off the instructions you posted on the support forum before, and ran through your procedue exactly, (twice) but I'm sorry to inform you that I haven't been able to re-establish my wireless internet connection. Would it be safe for me to assume at this stage that my modem is indeed fualty? It contines to work fine independantly, (I'm using it right now) but it can't seem to make contact with the basestation.
Will.

Define static IP for both LAN and W-LAN devices with an Airport Extreme Base Station

Hey guys,
I have a lot of different devices connected to my Airport Extreme Base Station (5th Gen) either wirelessly or via ethernet cable. Since I control some of them via VNC and currently have to find the corresponding IP-addresses through trial-and-error, I'd like to define static IP-addresses for the computers in question. My network consists of a cable modem connected to a TP-Link WR1043ND router in the basement, from which an ethernet cable leads to the WAN-port of the aforementioned Airport Extreme Base Station on the 2nd floor. Two of the devices I want to remote-access are wired to a D-Link DES-1005D switch, which in turn is connected to the 1st ethernet port of the Airport Base Station. The remaining 3 remote clients are connected over 802.11n. All computers run Windows.
My problem now is that even though I was able to define static IP-addresses employing the "DHCP only" router mode, this didn't seem to work for the two computers connected via ethernet. Not only did I lose any internet connectivity with those, I even lost the ability to remote-connect to them using the VNC-viewer.
The question now is: how do I specify static IP-addresses for my ethernet devices correctly?
I hope you can help me.

My network consists of a cable modem connected to a TP-Link WR1043ND router in the basement, from which an ethernet cable leads to the WAN-port of the aforementioned Airport Extreme Base Station on the 2nd floor.
If you read the information in the other post, my answer would be the same here.
The Router Mode of DHCP Only is rarely used, and would only really be appropriate if your ISP was providing you with a fixed bank of multiple fixed or static IP addresses to use. This does not appear to be the case in your post.
If this were the case, the first IP address would be used as a Static IP address for your connection, and other devices on your network would receive the other fixed IP addresses.
99%+ of the time, you would use the Router Mode setting of DHCP and NAT on a network when you want the AirPort to perform as the main router for the network.
But......your post also indicates that you have another router upstream on your network from the AirPort Extreme. You would not want to run two routers in series on a network. That explains the problems that you are having.
The AirPort Extreme needs to be configured in Bridge Mode. It cannot be the "main" router on your network when you already have another router on the network. That is a fundamental networking rule.

Using Airport Extreme base station as wireless Cable router and airtunes.

Can I replace my wired Roadrunner cable modem with a Apple Airport Extreme wireless 56g router removing the wired modem out of the picture?
I just have read and have not come to the complete conclusion that the Airport extreme base station is a standalone wireless router.
I would like this if it is a wireless standalone router as I want to but a pair of wireless airtunes router for music around the house keeping the Airport Extreme in my room where the airtunes routers would not be as I have the computer in my room and I have iTunes right there and would not need the airtunes routers in my computer room.
Leon.

Can I replace my wired Roadrunner cable modem with a Apple Airport Extreme wireless 56g router removing the wired modem out of the picture?
The AirPort Extreme Base Station (AEBS) does NOT have a built-in DSL/Cable modem. You will still require a Cable modem in order to access your ISP's Internet service.
I just have read and have not come to the complete conclusion that the Airport extreme base station is a standalone wireless router.
The AEBS IS a wireless router, but it is NOT a combination wireless router & cable modem.

Airport Extreme Base Station Internet Connection issue

I have a connection question for Airport Extreme Base Station.
I have Comcast cable broadband. I connect that to a Linksys router for
use with my Vonage phone, and then from the Linksys router I connect
via Ethernet to my iMac. I like the direct Ethernet connection for
performance reasons.
In order to set up a home network to connect my Tivo's (and eventually
my PC and printer), I have set up an Airport Extreme Base station and
connected it to the Linksys router from it's ethernet connection to the
WAN (cable modem) input on the Extreme.
I have connected to the Airport network with my iMac, but since I am
connected to the Internet via Ethernet, I cannot tell if my Airport is
connected to the Internet so that I can use it for my Tivo. My PC is
still in storage from a move, so I can't check with that.
My question: How can I tell if my Airport is connected to the Internet
without disabling my Ethernet connection on my iMac?
A few more info points/questions in case it helps answer:
1) I previously used this Airport to connect this iMac wirelessly.
2) Should I be connecting it to the LAN port since it's coming out of
the router?
3) If the connection issue is because I am going through the Linksys
first, can I connect the modem to the airport and then use the LAN port
to connect to the Linksys router?
4) If I have to disable the ethernet connection to test the Airport,
how do I do it? Just unplug it?
I appreciate any help as the online and manual help from Apple is not
quite up to par with such a complex configuration.
Regards
Bill

2) Should I be connecting it to the LAN port since it's coming out of
the router?
No, connecting to the WAN port is fine.
3) If the connection issue is because I am going through the Linksys
first, can I connect the modem to the airport and then use the LAN port
to connect to the Linksys router?
The issue is that you have two routers which effectively creates two networks. Unless this was your original intent, you will want to setup the AEBS as a bridge.
To set up the AirPort Extreme Base Station (AEBS) as a bridge, using the AirPort Admin Utility, connect your computer directly (using an Ethernet cable) to the LAN port of the AEBS, and then, make these settings:
Network tab
- Distribute IP addresses (unchecked)
- Apply the new settings.
- Wait at least 5 minutes.
4) If I have to disable the ethernet connection to test the Airport,
how do I do it? Just unplug it?
Well, that's certainly one way, but an easier way is to temporarily disable the "Built-in Ethernet" in your network configuration.
System Preferences > Network > Show > Network Port Configurations
- Built-in Ethernet (unchecked)

Printing wirelessly to MacBook Pro with Airport Extreme Base Station

I have an Airport Extreme Base Station that I used to use wirelessly until I got Verizon Fios. The Fios technicians said the base station couldn't be used and so it's been sitting unused for a few months. However, I really, really miss printing wirelessly, and was wondering if it was possible to use the Airport Extreme Base Station ONLY to print wirelessly, and not connect it any way to my internet (I don't want to mess with any of the fios stuff at all).
If it's not possible, is there any other way to print wirelessly without purchasing another product or special printer. I have a HP c4480 printer.
Thanks!

If your printer has a USB cable the easy way to go about this in my opinion is to plug that USB cable into your Extreme base station. I have the Extreme ABS that looks like a flying saucer. I plug the usb cable into the port that has the symbol that doe NOT look like this <--> rather it looks like a Saguaro cactus.
My computer then sends print documents to the Extreme via WiFi and then Extreme sends them to the printer via the USB cable.
If your Airport status is not showing in the Mac's menubar go to system Prefs/Network/Airport and check a little box so it will show up in the menu bar.
Now if your Extreme is plugged in the wall and powered up your Mac should be able to find it. Click on that menubar item for Airport and scroll down and select your Airport Extreme. I don't know for sure what its name will be. It should still be the same as it used to be when you used it last.
Now try printing a simple document. In the print dialog window you should be able to select what printer you want to use. If your new Extreme printer is listed select it. You may need to click on Print & Fax and figure out how to select it from there, and choose it to be the new default printer.
I think this info will do the job. Whenever you want to print you have to go to the Airport icon in the menubar and change your airport connection from your Verizon stuff to your Extreme. Then of course you have to change back when you are done. That is why it would be great to toss the Verizon WiFi radio out the window and just plug your Verizon modem into your Extreme WiFi radio transceiver (router). But I understand you cannot deal with that at this time.
If this does not do the job, if I have missed something, I will bet you 5 bucks that you can still figure it out if you just look at any error messages and/or look at the Print&Fax prefs and the Print dialog windows etc. and see what I may have missed. Maybe you have to go to SystemPrefs/Sharing and allow your printer to be shared. I don't think so. The way I figure any of this stuff out is to just look at stuff and think and try things and see what happens.
Your Verizon setup should be something like this.... a cable comes into your house and goes to a 'modem'. From there and ethernet cable (CAT-5 cable) goes from that modem to your Verizon router (WiFi radio transceiver).
As for getting rid of the Verizon router, when you are ready to give it a go, simply unplug the ethernet cable (it has a plug on the end that looks like the kind of plug that telephones use to plug into the wall, except it is a bit wider, but still has that same kind of snap-lock tab) that comes from the Verizon modem (the modem has the heavy round cable and probably many blinking lights) and plug it into the Extreme. Mine has an icon on the Extreme that is many dots in a circular pattern.
At this point you may have to unplug the Verizon modem form the wall AC power and the Extreme also. Then plug them back in, wait a minute, go to your Airport icon on your Mac menubar, Select Extreme and start surfing the web.
It really is that simple with a Mac. Maybe Verizon has found a way to make things difficult but my guess is no. Any password should be taken care of in your Airport Setup Utility program. It should be the same password(s) as you used before when you used your Extreme.

Bridging network with AP Extreme base station and AP Express

OK, here's the deal. I have an Airport Extreme Base Station on a WPA2 Personal network. Works great except that I want to boost the signal to the rest of the house. So, I bought an Airport Express. Airport Utility picks up both devices; but when I select the new Express to configure it, I get a msg asking to confirm that I want to switch networks. Well, I don't. I want to expand the network I have. Last night I did click "yes" and it was a disaster as I lost the Extreme altogether and the Express couldn't pick up a signal because - obviously - it wasn't connected to the ethernet cable as the base station, and also because (I think) the base station is configured to hide my SSID. I ended up working backwards and got the Extreme back to normal and put the Express back in its box until someone can tell me how to do this. I know Apple says it's easy; but it's a challenge for me. HELP!

A few things:
1. Please don't configure your base station to "hide its SSID". Doing this is absolutely useless as a security method. It will on the other hand complicate setup of your network, as well as the diagnosis of problems when they arise.
2. You must allow the Airport Utility to switch networks during the process. What is happening is that the Airport Utility must temporarily switch your Mac's wireless network connection from your existing base station to the wireless network created by your unconfigured Airport Express in order to communicate with and configure that Airport Express. After the Airport Express configuration is complete - if your Mac doesn't automatically switch your Mac's wireless network connection back again then just do so manually from the MacOS Airport menu.
3. To get a better understanding of what you are doing, start reading at page 42 of Apple's manual "Designing Airport Networks" found at:
http://manuals.info.apple.com/en/DesigningAirPort_Networks_Using_AirPortUtility.pdf

My internet works fine with my wired cable modem, but when i connect to my extreme base station and setup my wireless network the internet no longer works and my apple tv by default

Similar Messages

Maybe you are looking for