My iPad does not ring when I am getting a FaceTime call. And my volume is on. Also I have noticed when I charge my iPad at night I no longer hear that connection sound that it used to make. And lastly, my iPad will not flip when turned.
I no longer get a ring tone in face time when receiving an incoming call. My volume is turned on. Then I noticed when I charge my iPad at night, when I make the USB connection, it does not make tha connection sound any longer. And now my iPad will not flip. It only stays in one direction. Has anyone experienced these things? I do not know what to do about these issues. Thanks.
Have you tried resetting your iPad?
Reset: Press the Home and On/Off buttons at the same time and hold them until the Apple logo appears (about 10 seconds). Ignore the "Slide to power off"
Similar Messages
-
I have two hard drives on my mac 10.5.8 power pc and hear the clickking sounds of the first hard drive and think that it may be dying, can I install everything on the other hard drive also and wait for the first drive to die before i use the other drives? Or, what is the best way to handle this?
I do not know what you are waiting for.
I'd make a backup of your important stuff before cloning the entire disk.
Carbon Copy Cloner will copy your startup drive to an external firewire drive. You can boot from the external drive to verify that you have a good clone. When you upgrade your existing startup drive, you can at any time boot from your external drive and go back to your existing system.
http://www.bombich.com/software/ccc.html
SuperDuper is the wildly acclaimed program that makes recovery painless, because it makes creating a fully bootable backup painless. Its incredibly clear, friendly interface is understandable, easy to use, and SuperDuper's built-in scheduler makes it trivial to back up automatically. And it runs beautifully on both Intel and Power PC Macs! -
I have 2 games Words with Friends and Cityville that receives a Pop-up message form iTunes... "Connect to iTunes to use Push Notifications" and will not allow me to exit out of the app or play. How can I get this message to STOP?
Yes - I connected my phone to my computer / Itunes and went into the apps section, but from there I have no idea how to manage the push notifications. I even tryied going into itunes that is installed on my phone. I still cannot find anyplace to manage these popups. I have also gone into settings - notifiations - and tried turning all notifications for these apps all off but that didnt work either. Any guidance is MUCH appreciated - Im not sure where to go from here.
-
when i am connecting ipod with laptop, an error is coming that "this ipod cannot be used because the apple mobile device services is not started???
please revert.Did you try to restart the service, as described in this article?
http://support.apple.com/kb/TS1567 -
Everytime i connect my ipod to the computer, itunes says that this ipod cannot be used because the apple mobile device service is not started, what should i do?
See this article for how to restart this service.
http://support.apple.com/kb/TS1567
B-rock -
My songs that I purchased on my itunes account from my dad's computer will not play on my new computer, I have access to my entire account but can only play songs purchased using my new computer. Does anyone have any ideas?
Hi Kevin,
Have you authorized the Computer to your Apple ID?
If not, sign on to iTunes.
Then got to the Store menu option at the top of the screen (CTL+B if it is not showing), and click on it to display the dropdown, and select Authorize this computer.
If that doesn't work, then sign on your Dad's iTunes ID and repeat the Authorization process.
Cheers,
GB -
How to Create a Bootable Flash Drive to do a clean install of Lion. I have tried to use the InstallESD.dmg but it still will not do a clean install so that I do not have to do a reinstall from the Recovery (That just re downloads and takes over 6 hours)?
The system I'm have is a Mac-mini that had SL on it and no SuperDrive. I have also call Apple Support and they have really have not been to much help over 1st did my up grade to Lion and Installed the Lion Server.... it lost my SSL that I paid for and kill almost on of my server setting, plus kill all my web servers (using apache vhosts), and not to say the LDAP will even let remote users login to your laptops.
PS: There is no way that I'm going to buy a Install USB from Apple... They have over billed me over $300.00 because the Apps Store still has bugs (Glad I did not write that App/Service)
If there is anyone that can give in the information to create a USB install stick, I would be very thinkful.Here you are bro, courtesy of "softpedia.com"....brilliant site!!!
If you ever had problems with your Mac OS X installation you know that the first thing you should do is to check the startup volume using Disk Utility.
After the check has ended and, if the errors exceed a certain level of seriousness, the Disk Utility application will require you to restart your Mac and use its Mac OS X Install disc counterpart.
Other users may have to reinstall OS X altogether, but will find, or already know, that their SuperDrive (a CD/DVD reader and write combo drive) is not functioning properly and it will not be able to read the Install disc.
Although this might happen to Mac OS X Leopard users due to faultyhardware, the vast majority of problematic SuperDrives will be encountered inside Snow Leopard running Macs.
This is due to the updated SuperDrive firmware included in either the Install disc or the software updates one has to install to reach the latest version of OS X, namely 10.6.6.
This can be fixed by flashing the SuperDrive’s stock firmware using free command line tools that one can find for free online (I will write about this process also, but at a later time because this article only focuses on allowing you to create your own alternative USB boot disc).
If you are reading this last bit of information with skepticism, than you should know that it happened to me too. Despite all my tries to make it work properly, the SuperDrive kept on munching any inserted DVDs and just popped them out in about twenty seconds.
The workaround to this issue was to create my own Leopard bootable USB memory stick. I am not suggesting a Snow Leopard bootable stick mainly because there are lots of users that have decided to buy the cheaper, Upgrade version, which I have not tested and, therefore, I’m not sure if it will work properly once written to a USB disk.
And now, here are the exact steps you should follow in order to obtain a fully bootable Leopard (or Lion) Install disc.
Step 1 (If you already have the Leopard install disc DMG file you can skip to Step 2)
Launch Disk Utility (you can find it inside /Applications/Utilities). Here select the Leopard Install disc in the list of drives on the left and click on the New Image menu entry at the top of the window. A save message will appear where you will have to select the Desktop as a destination.
Step 2
After Disk Utility has finished creating the Leopard DMG, insert your USB stick and erase all data and reformat the disk. To do this select the USB in the list of drives on the left and, after clicking on the Erase tab on the right side of the window, choose the Mac OS Extended (Journaled) format and click the Erase button beneath.
Step 3
After the USB has been reformatted, download the SuperDuper app from HERE and launch it. Once SuperDuper starts, you will only have to select the DMG in the Copy drop-down menu, your USB memory stick on the right and hit the “Copy Now” button.
One can also use Disk Utility for this task but creating a bootable USB stick failed 2 out 4 times when copying the DMG to the stick (with the exact same settings each time). Creating the bootable stick using SuperDuper proved to be the perfect way to do it because it worked each of the 4 times I tested it.
The steps above can also be used to create a bootable Mac OS X Lion USB by using the InstallESD.dmg image you can find inside the Lion installer (named “Install Mac OS X Lion.app”) downloaded from the Mac App Store in the /Applications folder.
To locate the InstallESD.dmg right click the Lion installer, select the “Show Package Contents” entry, go inside the “Contents” folder, and from there into the “SharedSupport” folder. Inside this folder you can find the InstallESD.dmg you can use to create your own bootable Mac OS X Lion USB stick. To do so, go to the third step described above and use the InstallESD.dmg as the DMG to be copied to your USB disc.
That’s it! Once the process ends you will have a fully bootable Leopard (or Lion) USB disk that you can use as an alternative to the Apple’s DVD Install disc that comes bundled with all Macs.
To use your newly created bootable disk you will have to restart the Mac, press and hold the OPTION key until the StartupManager appears. Here, select the Mac OS X Install disk using your keyboard arrows and press return to start from the selected drive. -
TS3367 My iPad doesn't ring, when I get a FaceTime call. How do I turn on the ringer,...???
My iPad doesn't ring, when I get a FaceTime call. How do I turn on the ringer,...???
This is very easy to resolve in 3 easy steps. goto
1. settings
2. general
3. where it says 'Use Side switch to' you will see two choices
a) Lock rotation
b) Mute
Mute will be ticked if you are not getting a ringtone when someone calls you on Facetime
Simply Click on 'Lock Rotation'
Lock Rotation will now be ticked
Mute will be unticked.
Facetime calls will now ring your iPad2 -
My TV has only 2 HDMI conections that are all ready in use for Directv and the Blueray. Can I use composed cables to conect Apple TV
I'm going to take a guess and say that if your TV has 2 HDMI ports, it also has a component input (5 wire). I'm also going to guess that either your DirecTv or your Blueray has a component output option. If I had this setup, I would put my DTV on the component option and use the open HDMI port for the ATV2.
I doubt you will be able to tell the difference on your DTV. Most of the stores that demo HD use component wiring on their store models. The only downside is that you may be giving up the highest sound (Dobly 5.1 or whatever they call it.)
Or you could just go to switching the HDMI cords from your BluRay to the ATV2 depending on which one you are watching. I think I use my BluRay about 5% or less of my viewing time. If I "tossed", I wouldn't shed a tear. -
when i plug my ipod 4g into my computer is says that "this ipod cannot be used because the apple mobile device service is not started" what do i do?
http://support.apple.com/kb/TS1567
There have been some problems accessing pages on the Apple web site. If the hyperlink gives you a "We're sorry" message, try again. -
my iphone is able to charge when i connect it to my computor, but no matter what i do, will not show up on itunes. i have tried resetting both the computer and the iphone and nothing is working.
Type "ipad not recognized in itunes" or similar into the search bar at the top of this page by "Support".
-
I updated my Apple Iphone 3GS this morning and now my charger will not work. I can use my boyfirends just fine but mine will not worl at all. Why is this and is there anything that I can do?
Something is wrong with your charger or cable.
If it works with another charger, then it is not the iphone -
the external GPS is used only for 911 but the device will not operate without it...this causes great inconvenience for me, having to run that cable to a window in the two houses I use it..is there a way to disable the GPS if I do not care about the 911 functionability..? this is the only downside I have with the network extender and it renders my device useless..
Nope, GPS is a Federal requirement for anything operating a cellular telephone signal. You don't ever plan to call 911 until you are in an emergency. I don't see that requirement changing any time soon.
If you are truly inconvenienced by the VZW network extender then perhaps you should disable you calling features in these areas and swap over to WiFi only. There are many services and apps out there that can route your phone services through internet service providers. -
My ipad says it is connected to WiFi, which is workingly perfectly for several other devices, will not connect to internet. It keeps giving the message 'Cannot Connect' or error has occurred or just blink off site or icon?
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
• Launch Settings app
• Tap on Wi-Fi
• Tap on the blue arrow of the Wi-Fi network that you connect to from the list
• In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
I am making my first keynote presentation. I transferred the slides from a power point. I did not use a 'theme' from keynote. Keynote will not let me 'name' the presentation and the 'save as' option will not come up in the menu. What have I done wrong
When it comes to Keynote, I try and start with a presentation that's 1680 x 1050 preset or something in that range. Most projectors that you'll get at a conference won't project much higher than that and if they run at a lower resolution, it's better to have the device downsize your Keynote. Anything is better than having the projector try and upsize your presentation... you work hard to make it look good, and it's mangled by some tired Epson projector.
As far as slides go, scan them in at 150 dpi or better, and make them at least the dimensions of your presentation. Keynote is really only wanting 72dpi, but I do them at 150, just in case I need to print out the presentation as a handout later, and having the pix at 150 dpi gives me a little help with their quality on a printer.
You'd probably have to drop in the 150 versions again if you output the Keynote to .pdf or Word or something, but at least you have the option.
And Gary's right (above) go ahead and scan them as TIFFs. Sooner or later you'll want to do something else with these slides (like make something for an iPad or the like) and having them as TIFFs keeps your presentation looking good.
Finally, and this is a big one, get to the location for your presentation ahead of time if you can, and plug the laptop in and see what you get. There's always connection problems. Don't let the AV bonehead tell you everything will work just fine ('... I don't have any adapters for a Mac...') . See it for yourself... you're the one that's standing up there. Unless it's your boss, then you better be really sure it works.
Maybe you are looking for
-
Internal hard drive won't mount
First off, thanks in advance to any who offer help with my frustrating problem. It would appear that my primary drive has come unmounted and will not remount. Yesterday I went to upgrade Corel Painter. The computer hung up when I launched the install
-
Hi, We have a requirement to send content in base64 encoded binary form. We have done all the encoding in ABAP and the BASE64 content is available in internal table. We need to use ABAP proxy to send the data to XI and further to target client via ht
-
Outlook mail being received but blank screen when I open the app
Outlook mail being received but blank screen when I open the app
-
Airport Extreme and Westell DSL modem
Hi all, I am a MCSE Certified Professional in Windows 2000. I got a new Apple Airport Extreme router to replace my Sister's Netgear router. I kept having to reset it all the time. In setting up the Airport I found out that the Westell modem actually
-
Edit DVCAM but output in HDV - possible?
Dear All I would be very interested in hearing any views in what many of you might find a very simple question. I have shot a project in Sony HDV. I would like to down convert and edit in DVCam (to save disk space and because I'm nt sure my Mac can e