My Iphone4 speaker wont sound play any audio and all it says when i try turning it up is " Ringer" But doesent show the bars the turn up or down. Any help? :/

My Iphone4 speaker wont sound play any audio and all it says when i try turning it up is " Ringer" But doesent show the bars the turn up or down. Any help? :/

Hey Hype.Beast.187,
Here are some troubleshooting steps for not being able to hear sound through your iPhone speakers. I'd pay special attention to steps 8, 9, and 10 in your situation:
Resolution
Verify that there is nothing plugged in to the headset jack, including headsets, headphones, or adapters.
Make sure the Ring/Silent switch is not switched to silent.
While on the Home screen, adjust the volume buttons. If you see the icon below, indicating that headphones are attached, there may be debris or an object lodged in the headset jack:
Check the headset jack. If there is an object lodged in the headset jack that is not easily removed, have the iPhone serviced to remove object.
For Original iPhone: If there is light debris, such as lint, in the headset jack, try connecting a pair of headphones to the headset jack and then remove the headphones. Repeat this several times to remove the debris.
If you have installed a protective film on the display, either ensure that the receiver is not covered or remove the film completely.
Check the receiver mesh (which is on the top front of the device, above the display). If it appears blocked, use a clean, small, dry, soft-bristled brush to carefully and gently brush away any debris.
If you have paired with a Bluetooth headset that is nearby, either use the headset or turn Bluetooth off (choose Settings > General > Bluetooth).
Restart the iPhone.
If restarting the iPhone doesn't resolve the issue, try restoring the device.
If the issue persists, go to the Service Answer Center - iPhone for information on service.
iPhone: Can't hear through the receiver or speakers
http://support.apple.com/kb/TS1630
All the best,
David

Similar Messages

  • When i try to set a folder, it does not show up on the far left which doesn't allow me to enter any projects in the folder..

    In trying to set up a folder, it doesn't appear on the far left but it shows up directly under other projects.  Because it doesn't set up on the far left I can't put any projects in the folder.

    Currently what I'm doing to set up a folder is go to "new" to create a folder but what I get is a folder that is directly positioned under a symbol such as a project and not out to the left of the other symbols.
    Probably you get a folder directly beneath a project, because you have selected that project. But still you should be able to drag the folder to a higher level so that you can move projects into it.
    If nothing else helps, switch to "Projects" View (by clicking on the prject icon on top of the Library Inspector) before you select "File -> New -> Folder" . That should create the new Folder at the bottom of your folder list, far to the left, and you should be able to drag projects to it.

  • Portable Wireless Server WG-C10 doesn't stream any audio and some video content after updating phone to Android Lollipop 5.x

    The Portable Wireless Server WG-C10 I purchased in 2014 doesn't stream any audio and some video content after updating phone to Android Lollipop 5.x.
    The WG-C10 firmware is the last version which is available and the PWS Manager software is the last version available in Google Play Store.
    There are no updates for the WG-C10 firmware nor PWS Manager software since 2013 or for Android 5.x (Lollipop) and I don't know if the WG-C10 firmware is the problem or if the PWS Manager software is the problem.
    BTW, I am still able to stream this content on my tablet which is on KitKat (4.4.x) so the files are not corrupted.  The only problem is with Lollipop.
    PWS Manager in the Google Play Store says it supports Android 4.0+ which is no longer true.
    The audio file formats which fail to stream are:  mp3 and wav
    The video file formats which fail to stream are:  mp4, avi and 3gp
    JPEG Images appear to work fine, but I haven't tried other formats.
    I purchased the WG-C10 to stream audio and video primarily to my phone and now that this no longer works, the WG-C10 is useless to me.
    Any ideas?

    Hi juicespeare1,
    Welcome to the Sony Community!
    Upon checking your inquiry, the best division to respond to your concern is our Sony Mobile department.
    You can reach them at this site: http://www.sonymobile.com/global-en/support/contact-us/contact-info/.
    If my post answers your question, please mark it as "Accept as Solution"

  • Sound on my phone has gone so when someone calls me they can hear me but i cant hear them.The ticks cant be heard when you press the keyboard. I've checked the settings and they are ok. can still hear music thru headphones but not without. Any help pls.

    sound on my phone has gone so when someone calls me they can hear me but i cant hear them.The ticks cant be heard when you press the keyboard. I've checked the settings and they are ok. can still hear music thru headphones but not without. Any help pls.

    Hey shahbazfromgbr,
    Thanks for the question, and welcome to Apple Support Communities.
    I understand you are having issues with sound output on your iPhone 4S. For troubleshooting steps, the following article provides the best information:
    iPhone: Can't hear through the receiver or speakers
    http://support.apple.com/kb/TS1630
    1. Verify that there is nothing plugged in to the headset jack, including headsets, headphones, or adapters.
    2. Make sure the Ring/Silent switch is not switched to silent.
    3. While on the Home screen, adjust the volume buttons. If you see the icon below, indicating that headphones are attached, there may be debris or an object lodged in the headset jack:
    4. Check the headset jack. If there is an object lodged in the headset jack that is not easily removed, have the iPhone serviced to remove object.
    5. For Original iPhone: If there is light debris, such as lint, in the headset jack, try connecting a pair of headphones to the headset jack and then remove the headphones. Repeat this several times to remove the debris.
    6. If you have installed a protective film on the display, either ensure that the receiver is not covered or remove the film completely.
    7. Check the receiver mesh (which is on the top front of the device, above the display). If it appears blocked, use a clean, small, dry, soft-bristled brush to carefully and gently brush away any debris.
    8. If you have paired with a Bluetooth headset that is nearby, either use the headset or turn Bluetooth off (choose Settings > General > Bluetooth).
    9. Restart the iPhone.
    10. If restarting the iPhone doesn't resolve the issue, try restoring the device.
    11. If the issue persists, go to the Service Answer Center - iPhone for information on service.
    Thanks,
    Matt M.

  • HT3275 My Time Capsule has been backing up without any problems and all of a sudden it stops reading on my computer. The external hard drive beeps three times and the motter wont run within. What happened?

    My Time Capsule has been backing up without any problems and all of a sudden it stops reading on my computer. The external hard drive beeps three times and the motter wont run within. The light that usually blinks while in use is no longer blinking and is on constant. What happened?

    abailey46 wrote:
    My Time Capsule has been backing up without any problems and all of a sudden it stops reading on my computer. The external hard drive beeps three times and the motter wont run within. The light that usually blinks while in use is no longer blinking and is on constant. What happened?
    Sorry we are unclear as to the external hard drive and its connection to the TC..
    For instance the light that blinks.. is that the TC or external hard disk or what.
    Did you try just rebooting / restart the whole network in correct order.. modem.. router / TC.. external drive.. clients with 2min gap between each.
    Are you actually running Snow Leopard as the profile states?
    How old is the TC?

  • TS1717 Itunes crashes when I try to playback iTunes purchased movies that have been burnt to Verbatim DVD-R discs.  Any thoughts?

    Itunes crashes when I try to playback iTunes purchased movies that have been burnt to Verbatim DVD-R discs.  Any thoughts?

    Try the following user tip with that one:
    iTunes for Windows 10.7.0.21: "iTunes has stopped working" error messages when playing videos, video podcasts, movies and TV shows

  • Why can't I update or load new apps on my iPhone and iPad. It does not ask me for my password. I tried to sync from my laptop now I am unable to connect to any sites from internet explorer. When I try to update or load any app it tells me it is corrupt

    Why can't I update or load new apps on my iPhone and iPad. It does not ask me for my password. I tried to sync from my laptop now I am unable to connect to any sites from internet explorer. When I try to update or load any app it tells me it is corrupt

    You need to ask Apple for assistance with getting back into your old ID. To do this, click here and pick a method; if that page doesn't list one for your country or you're unable to resolve this issue through the Account Security team, fill out and submit this form.
    (118441)

  • My mac air died, after i reinstall from dvd drive, when i boot up again, i saw a prohibit sign showing up on the screen, then get to my logon screen.  After logon, it takes very long time to load any application.  pls help

    my mac air died, after i reinstall from dvd drive, when i boot up again, i saw a prohibit sign showing up on the screen, then get to my logon screen.  After logon, it takes very long time to load any application.  pls help

    OK. If you believe that.
    When the disk is starting to die it can be bad for a moment and then be good for a while. If there was no problem while you were checking it of course it shows up good.
    I tell you those are the signs of a disk that is about to die.
    Allan

  • My e-mail has changed, but I purchashed some songs in iTunes using my old e-mail address as my account name... so when I try to play the sonngs I bought and paid for - it keeps asking me to authorize my PC first, but I don't remember the password!

    My e-mail has changed, but I purchashed some songs in iTunes using my old e-mail address as my account name... so when I try to play the sonngs I bought and paid for - it keeps asking me to authorize my PC first, but I don't remember the password! And since the old e-mail address is no longer active, I can't even chenge the password- becasue it's sends the link to do so via e-mail!  Even when I use the "ask personal questions" option to verify and it asks me for my date of birth, I put it in and it still won't acccept.

    Hello there, loupar.
    The following Knowledge Base article offers up just how to change your Apple ID for the App Store on your iOS device:
    iOS: Sign in with a different Apple ID in the iTunes Store, App Store, and iBooks Store
    http://support.apple.com/kb/ht1311
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

  • TS3938 Hi, I have a sign being advised Power PC Applications no longer supported when I try to go into Microsoft Word, Excel, Entourage & MSN Messenger, hoe do I resolve this? Any help appreciated.

    Hi, I have a sign being advised Power PC Applications no longer supported when I try to go into Microsoft Word, Excel, Entourage & MSN Messenger, hoe do I resolve this? Any help appreciated Sorry, this is for a Mac Air

    Most versions of Office 2008 use an Universal installer. A few have one which is PowerPC-only.
    In any case, Mac OS X Server 10.6 can be run in emulation, and Rosetta applications can be run in it. Saying that PowerPC-only applications won't run in Mac OS X 10.7 is correct. Saying that they won't run on a Mac which shipped with Mac OS X 10.7 is not.
    (66375)

  • I have iMac and lion OS. When I try to download (free or not) any program it always  message "There was an error in the App Store. Please try again later. (13)

    I have iMac and lion OS. When I try to download (free or not) any program it always  message "There was an error in the App Store. Please try again later. (13)

    http://www.apple.com/support/mac/app-store/contact.html?form=account

  • Tried to check on updates for CS6 64 bit - Received message saying application manager may be damaged - download and install new copy - when I try this I receive message ERROR 404 I have a PC - any help would be gratefully received - thanks - William

    Tried to check on updates for CS6 64 bit - Received message saying application manager may be damaged - download and install new copy - when I try this I receive message ERROR 404 I have a PC - any help would be gratefully received - thanks - William

    reset your preferences:
    dreamweaver:  http://helpx.adobe.com/dreamweaver/kb/restore-preferences-dreamweaver-cs4-cs5.html
    flash:  http://helpx.adobe.com/flash/kb/re-create-preferences-flash-professional.html
    indesign:  https://forums.adobe.com/thread/526990
    lightroom:  http://www.lightroomforums.net/showthread.php?14226-Resetting-%28or-Trashing-%29-the-Light room-Preferences-file
    photoshop:  https://forums.adobe.com/thread/375776
    if that fails, uninstall ps, clean (Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6) and reinstall.  then use the manual updates.

  • Whenever i try to watch one of my downloaded tv shows or movies the screen turns green and i can only hear audio

    when i try to watch a downloaded movie or tv show the screen turns green and only audio plays

    This forum is for questions from those managing sites on iTunes U, Apple's service for colleges and universities to post educational material in the iTunes Store. You'll be most likely to get help with this issue if you ask in the general iTunes for Mac forum.
    Regards.

  • I have buy 4s it's unlocked and its working with different carriers in Bahrain but in Pakistan I try to use different carriers's sims but its showing sim is not valid , not compatible? any one please help me out this

    I have buy 4s it's unlocked and its working ok with different carriers in Bahrain, but in Pakistan I try to use different carriers's sims but its showing sim is not valid , not compatible? any one please help me out this?

    Try restoring the iPhone to factory settings. If you are having difficult restoring, put the iPhone into Recovery Mode and see if that then works:
    http://support.apple.com/kb/ht1808
    If not, or if a restore to factory settings does not fix the problem, then your iPhone may have a hardware problem. You can only get the iPhone serviced by Apple in Canada, so you will have to take the iPhone there or send it to someone you know in Canada who can get the iPhone serviced and send it back to you. The only option for getting service in Pakistan would be to pay some unauthorized repair shop to attempt a repair, after which Apple will no longer provide any service even in Canada.
    Regards.

  • I have a iphone4s and an ipod 4th gen, they both share same itunes acc, the ipod has its own email but when people try to FT it also rings on my phone, how do i stop it ringing both devices

    i have a iphone4s and an ipod 4th gen, they both share same itunes acc, the ipod has its own email but when people try to FT it also rings on my phone, how do i stop it ringing both devices

    That's because you're using the same Apple ID on both devices. On your phone: Settings>FaceTime>You Can Be Reached at>Remove your Apple ID.

Maybe you are looking for

  • Uploading files using FTP(Linlyn class)

    I'm currently learning java right now on my own, and I'm having some trouble. I'm trying to upload a txt file using the linlyn class. How do you create a file then upload it on an applet?

  • Integrate Custom App in Fiori Launchpad - Duplicate ID Error

    Hey guys, I integrated a custom app in the fiori launchpad. The first launch works perfectly. But if I go back via the navigation button and try to start my application again I get following error message: 2015-04-23 23:40:28 adding element with dupl

  • OVM 3 manager Console doesnt load.. OVMAPI_6000E Internal Error

    I had deployed OVM manager 3 in my environment. I have a bunch of VMs running on the 2 OVS Servers which are managed by my OVM Manager 3 . I was having some issues with Restarting VMs., and hence restarted the OVM Manager.. Now My Manager console won

  • Batch management no ranges

    HI all               I want to create new no range for internal batch no assignment, there is one default range maintain and system picking that no range only. i wann use auto  batch generation during 101 all settings are done and batch no is creatin

  • How can i sync ringtones off my ipnone 4 onto itunes?

    i am helping my friends sync his iphone 4 to a new computer (orig one crashed) but we cannot find a way to sync or backup his ringtones off his iphone onto the new laptop. It keeps wanting to erase them since they are not on his new laptop. any help.