My iPod has a white screen.  After holding down the middle and the menu button it goes black, then back white, and then beeps twice but stays white.  It never shows the apple logo, just stays white - help!

My iPod has a white screen.  After holding down the middle and menu button, the screen goes black then back to white and beeps twice.  I have returned to original settings and resorted content to no avail.  I still have a white screen.  I have plugged it up and tried resetting again and again, still a white screen with two beeps - help.

I have the same exact issue. Fifth generation iPod Nano, blank screen, Restore had no effect. I'm running Windows 7 Home, with all software up-to-date. I suspect hardware damage. Any clarification would be appreciated. Thank you in advance.

Similar Messages

  • I turned off my iPad, but when I went to turn it back on, the apple logo just stays there. It's been there for 10 minutes, and hasn't gone away. Help please.

    I turned off my iPad, but when I went to turn it back on, the apple logo just stays there. It's been there for 10 minutes, and hasn't gone away. Help please.

    First thing to try is to reset your device. Press and hold the Home and Sleep buttons simultaneously ignoring the red slider should one appear until the Apple logo appears. Let go of the buttons and let the device restart. See if that fixes your problem.

  • What does it mean when the apple logo just stays on my iPad?

    I turned off my iPad, but when I went to turn it back on, the apple logo just stays there. It's been there for 10 minutes, and hasn't gone away. Help please.

    If reset doesn't work, you'll have to force your iPad into Recover Mode.
    Recovery Mode
    1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
    2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
    3.While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
    4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
    Note: Data will be lost. You may have to repeat the above many times.

  • HT201412 my phone restore but does not starts it shows only apple logo please help me

    HI
    My i phone restore but does not start it shows only apple logo & charging it was not connect to i tune please help me

    See your other post on this Topic...
    https://discussions.apple.com/message/22315227#22315227

  • My MacBook pro is stuck on white screen after shut down. Now, neither this is turn on nor turn off. I had to do

    My MacBook pro is stuck on white screen after shut down. Now, neither this is turn on nor turn off.

    You should be able to turn off your MBP by pressing the power button down continously for about 5-10 sec. When you reboot it you are going to want to enter into a terminal screen. Hopefully the following YouTube video helps: http://www.youtube.com/watch?v=qKOX72xNmbo

  • HT1339 i plugged my ipod to outlet charger to charge, it was working fine before then, but i left it charge for maybe an hour. i went to check it, and the screen just stays white, no apple logo,  just a white screen. whats wrong with it?

    How do I change the name of my ipod? It was used, i purchased it from a friend.

    I have 4 pc's at home and an imac, but the ipod has the same error on all of them. sorry for not pointing that out, seems that it works only on a MAC OS X, cause my imac isn't an OS X and it can't read the ipod either, it recognizes it as an ipod,and gives me info on it, but it freezes up also when I try to open it...thanks for trying to help.

  • Zen 4Gb White screen after hold m

    Hi,
    I have this problem on my zen 4gb: when I put it in hold mode, everything works fine, but when I put it back to "normal mode", then the screen becomes white. The player works but I can't see anything because it's white, I have to switch it off and then on to have a normal situation. I tried to reinstall the firmware (ver. .20.02) but nothing changed.
    Someone has the same problem? Have you a solution?
    Thank you,
    Enrico

    Ahh. The white screen. Have you reformated the player? Under creative media explorer tools, there is an option to format. Try this. If not, send it back. Here is a good forum too.
    www.anythingbutipod.com

  • TS3474 My ipod will not start even after holding down the Sleep/Wake button and the Volume Down button for at least eight seconds.  What is my next step?

    I have a sixth generation ipod 16gb nano.  It will not turn on.  I have tried hoding down the power button with the down volumn button without results.
    Any other suggestions?

    i have the same problem...my ipod is 4th generation?uggghhhhh

  • White Screen after Upgraded

    I have upgraded Lion to Mavericks. After I restarted my iMac often because he had hanged himself, now i get after the Apple logo just a white screen.
    iMac (27-inch, Mid 2011)
    Intel Core i5 - 3.1 MHz
    AMD Radeon HD 6970M
    Memory 16GB

    nobody can help me?

  • White Screen after start up chime and Apple logo, any common issues/reasons?

    Hi all,
    I have a 2011 quadcore i7, 4GB RAM MacBook Pro which has recently and suddenly developed this annoying fault. A perminant white screen after the Apple logo and spinwheel. I have removed the hard drive (from my early 2011 MacBook Pro) and did a clean install of Lion (10.7) and I know the harddrive is fine and functional as my Mac Pro is able to boot from it and works perfectly, put the same drive back into the MacBook Pro and same, start up chime - Apple Logo - Flash, screen stays white. So its not Harddrive and most likely not a software problem (as the drive has been whiped and OSX reinstalled.) Any thoughts that it may be a bust motherboard or graphics card?
    Already tried:
    Safe Boot
    Single-user Mode
    Verbode Mode
    Resetting the NVRAM/PRAM
    Wiping and installing OSX
    Disc recovery
    Internet Recovery
    Many thanks in advance

    Hi all,
    I have a 2011 quadcore i7, 4GB RAM MacBook Pro which has recently and suddenly developed this annoying fault. A perminant white screen after the Apple logo and spinwheel. I have removed the hard drive (from my early 2011 MacBook Pro) and did a clean install of Lion (10.7) and I know the harddrive is fine and functional as my Mac Pro is able to boot from it and works perfectly, put the same drive back into the MacBook Pro and same, start up chime - Apple Logo - Flash, screen stays white. So its not Harddrive and most likely not a software problem (as the drive has been whiped and OSX reinstalled.) Any thoughts that it may be a bust motherboard or graphics card?
    Already tried:
    Safe Boot
    Single-user Mode
    Verbode Mode
    Resetting the NVRAM/PRAM
    Wiping and installing OSX
    Disc recovery
    Internet Recovery
    Many thanks in advance

  • IPod 4th Gen has white screen after replacement, and restore

    Okay. Here's the problem. A while ago, I dropped my iPod, and it's screen cracked. I've been living with it ever since perfectly, but just with a cracked screen. Now, I ordered a new screen, and I begin to replace it. I knew how, and like an easy job, I did it pretty quick compared to others. After both ribbon cables where in, I pressed the lock button, and my iPod had a white screen. I was a little worried about that, so, I tried to reattach the screen. Now it was just black, after even using the home and lock button restart method. Eventually I got it back up and to the white screen by draining the battery and recharging, and there I was again, stuck. I looked at some forums on the internet to try to see if anyone had my problem. After clicking on the first link, it turns out, alot of people had this problem as well as me. The solution they said was pressing the home button and lock button for about 10 or so seconds, and then it goes to the apple screen and is all better again. I tried it, and my home button broke. Great. So, now I had to use the little button that the home button was pressing down to try the solution. Tried it, and, nothing. Still the blank, plain, white screen. Looked some more and saw that pressing the home and lock buttons along with the volume up button worked for some people too. Tried it, worked just as good as the previous one. Nothing. I even tried some person's idea of doing home, then volume up, then lock, in different timed stages. Nothing. I also saw people begging for them not to restore their iPods and begging for a solution. I was fine with a restore, I just had games that I played on my iPhone as well. So, I went with it, and restored it, without any backups, just going to factory mode. Afterwards I heard my iPod make the iOS "plugged in" sound, and anxiously tried the lock button. Still had the white screen. STILL. Now, I'm here, begging for a solution like others, with an iPod that won't function properly. Can someone please help me?

    No nothing like that happened, I'm sure, but I actually spent the day looking for a fix. Luckily, I had the idea of taping the spring down because I though the screen didn't touch it. Turns out I was right, but however, I found out that the screen I ordered was broken in a way, because it still had the white screen after the taping. Just to make sure, I tried the other screen to clarify if the taping worked or not. I did the home and lock button restart, and up popped the apple logo. So, that means that the screen I got from the seller was either a rip-off, or was just broken somehow in process of making, or delivering in some matter. Unfortunately, I think I can't ship it back unless for alot of money because the person I got it from comes from China. I live in the USA. So that's gonna be a matter to work with myself. Thank you for trying to help.

  • 7th generation iPod nano flashes apple logo with a white screen and won't play.  What is wrong with it?

    I have a 7th Generation iPod Nano that started flashing the Apple logo with a white background.  I have tried Diagnostics, restoring the iPod and even resetting it.  At one point it was in a Restore Loop.  I'm thinking maybe it has a virus but reading further says that I may be missing one of the drivers.  Is there any way to fix it without taking into a tech?? Please help...miss my music!!

    Hi jkjuarez2012,
    Thank you for visiting Apple Support Communities.
    It sounds like your iPod nano is only showing the Apple logo with a white background, and you've tried many good steps including resetting and restoring the device. I know I'd miss my music in this situation.
    Make sure that you followed the steps in this article when restoring your iPod:
    Restoring iPod to factory settings - Apple Support
    If the issue continues after restoring, your iPod nano may need to be serviced. You can use this link to find out more about iPod service:
    If the issue is still not resolved, please read this information on servicing your iPod.
    From:
    iPod nano (7th generation): Hardware troubleshooting - Apple Support
    Best Regards,
    Jeremy

  • My iPad won't charge after plugging into my computer and after holding down the power and home button at same time for 10 seconds- Can anybody help? Has IOS7.0 but the most up-to-date version

    My iPad won't charge after plugging into my computer and after holding down the power and home button at same time for 10 seconds… Can anybody help? Has IOS7.0 but not the most up-to-date version

    It's just the battery sign - nothing else. I've tried to reboot by holding down both power and home key for 10+ seconds, waiting for the apple logo - but nothing happens. It's plugged into the imac at the moment. I tried to recharge it overnight using the normal charger - but no luck. It went dead during a Skype call with a friend - even though it was powered into the mains - albeit at a low battery level at the time

  • IPod frozen white screen after cancelled wifi system update

    My iPod Touch 4g has a frozen white screen after cancelling wifi update to ios 5.1. My update bar was frozen middle way through when doing wifi update to ios 5.1. So i reset ipod and it displayed an apple logo which faded into a white screen. not jailbroken.

    I let battery drain, plugged into computer but when it booted up it booted to an apple logo with lines across the screen. It is frozen. iTunes did not recognise, it never showed up on iTunes. It is fading into a white screen.

  • TS3274 My iPad has a white screen after trying to restore.  I try and restore again and  the same thing happens and we are back at the white screen.  How can I get it back.

    My iPad has a white screen after trying to restore.  I try and restore again and  the same thing happens and we are back at the white screen.  How can I get it back?

    type HT4097 in the search bar. its unable to update or restore iOS. Follow the instructions and if that does not work then id go to the local apple store.

Maybe you are looking for

  • Tips/Hints re: using flash for live title graphics and visualisations

    Hi guys, this is my first post. I'm a design student from New Zealand, with a reasonably basic knowledge of flash, I've built a few relatively simple flash sites and applications for example. I got a job the other day to produce live title graphics f

  • ORA-7445 followed by ORA-472

    Hi All, My System Configuration is CPU: Intel Xeon Dual Core 2.5GHz. RAM: 8 GB Databse : Oracle 10.2.0.2 Interim Oracle Patch: 18 SAP: Solution Manager OS: Windows 2003 Standard Edition x86_64 I have install the system successfully. I stop the SAP sy

  • MAnaged system configuration error in solution manager

    Hi, While doing managed system configuration getting the error, below versions are using. MDM 7.1 SP10  Import server  and Solution manager 7.1 SP10. Can anyone help me?. Regards Chandra

  • C++ class question

    Hi, I have written a code for simulation of an N-body problem. The code compiles with a C++ compiler, but it is mainly plain C (no classes/objects, for now). The code uses a structure to encapsulate each particles' information (position, mass, etc.)

  • Adobe Reader 10.1.1.33 is crashing on Citrix/desktop since yesterday.

    Adobe 10.1.1.33 is crashing on Citrix/desktop. Getting error on all XenApp 6.5 Citrix on Windows 2008 server and Windows 7 desktops. Faulting application name: AcroRd32.exe, version: 10.1.1.33, time stamp: 0x4e64e4e2 Faulting module name: AcroRd32.dl