My ipod nano 6th gen just blinking

my ipod nano 6th gen is completely dead, i charged it in but now it doesn't stop blinking and it is all it does..

Hello Joey,
I would be concerned too if my iPod nano was not powering on completely. I recommend following the steps below:
Will not turn on or screen remains dark
Connect iPod to power for at least ten minutes to ensure that the battery has enough charge to allow iPod to turn on.
If iPod does not turn on after ten minutes, try resetting the device while it is still connected to power. Reset the iPod by holding down the Sleep/Wake button and the Volume Down button for at least eight seconds or until you see the Apple logo appear.
If the Apple logo appears on the display, connect iPod to a computer and verify that it appears in iTunes and can play music. If iPod appears in iTunes and can play music, no further troubleshooting is needed.
If the screen remains dark and will not turn on, then your iPod may need service.
I got this information from the following article:
iPod nano (6th generation): Hardware troubleshooting
http://support.apple.com/kb/ts3474
Additionally, I recommend reviewing this article for steps to take when your iPod is not recognized in iTunes:
iPod not appearing in iTunes
http://support.apple.com/kb/TS3716
Thank you for using Apple Support Communities.
Best,
Sheila M.

Similar Messages

My ipod nano 6th gen just flashes the apple logo when plugged in but goes blank when not plugged in. i have tried changing format to fat32 but i can't on windows 7

i have recently recieved an ipod nano 6th gen after the 1st gen recall, and out of nowhere it just started flashing the apple logo when connected to computer. Help please!

Universal Serial Bus controllers
     Intel(R) ICH9 Family USB Universal Host Controller - 2934
     Intel(R) ICH9 Family USB Universal Host Controller - 2935
     Intel(R) ICH9 Family USB Universal Host Controller - 2936
     Intel(R) ICH9 Family USB Universal Host Controller - 2937
     Intel(R) ICH9 Family USB Universal Host Controller - 2938
     Intel(R) ICH9 Family USB Universal Host Controller - 2939
     Intel(R) ICH9 Family USB Universal Host Controller - 293A
     Intel(R) ICH9 Family USB Universal Host Controller - 293C
     USB Composite Device
     USB Root Hub
     USB Root Hub
     USB Root Hub
     USB Root Hub
     USB Root Hub
     USB Root Hub
     USB Root Hub
     USB Root Hub
I'm not sure if it charged when I hooked it up to my roommate's computer, but it definately didn't register either. If I put it on the dock it plays so the port is fine, but that still doesn't help me sync it to my computer.

New iPod Nano 6th Gen just got it going today and it won't stay on. It starts playing a song and pauses (shuts down?) after a few seconds. It's fully charged what do i do? Help please!!

New iPod Nano 6th generation just got it going today. It is fully charged but shuts off a few seconds into a song, what do I do?

I received mine yesterday as replacement for 1st generation and yes I had exactly the same problem.
I don't think it is anything to do with headphone plug [jack].
I played around with the settings and have just managed to listen to three hours without problem.
Music settings; shake to shuttle off, sound check off, double click - play/pause, audio cross fade and group compilation on. Can't be all these but trial and error as to which one - unfortunately it came without instructions.
The only other thing was that I had it in pocket while i was moving whereas yesterday I was sat at desk with nano at rest.
iPod nano, Mac 10.6.8

My ipod nano 6th gen fell out of my pockey and the screen cracked badly, is there any coverage for this under warranty? I just bought it a month ago. If not what are the options for getting it fixed

My ipod nano 6th gen fell out of my pocket and the screen cracked badly, is there any coverage for this under warranty? I just bought it a month ago. If not what are the options for getting it fixed? It is pretty frustrating, it fell from about 3 feet out of my pocket and now looks like it was beaten by a hammer.

Debbie:
deborahfromwindsor wrote:
he advises restarting by inserting the OSX disc and pressing down the C button to reboot from there then selecting disk utility, hard disk and repair.... Does he mean me to hold down the C key on the alpha keyboard or the ctrl key?
Should I just ask for my money back??? If it is a simple repair do I just literally push the disc in, push the power button and hold down the C button?
That's where I would begin, too, with
Repair Disk
Insert Installer disk and Restart, holding down the "C" key until grey Apple appears.
Go to Installer menu (Panther and earlier) or Utilities menu (Tiger) and launch Disk Utility.
Select your HDD (manufacturer ID) in the left panel.
Select First Aid in the Main panel.
(Check S.M.A.R.TStatus of HDD at the bottom of right panel, and report if it saysanything but Verified)
Click Repair Disk on the bottom right.
If DU reports disk does not need repairs quit DU and restart.
If DU reports errors Repair again and again until DU reports disk is repaired.
If DU reports errors it cannot repair you will need touse autility like TechTool Pro,Drive Geniusor DiskWarrior
First we need to determine if the issue you are experiencing with the computer is software or hardware based. Once we have gotten things sorted out there should be time enough to make you decision about keeping or returning it.
cornelius

My ipod nano 6th gen doesn't start. When I plug it, only blink the apple logo on the screen. I try to reset it holding by 8 seconds start button and volume down and doesn't work. My Ipod doesn't have any shock or water damage. How can I do?

My ipod nano 6th gen doesn't start. When I plug it, only blink the apple logo on the screen. I try to reset it holding by 8 seconds start button and volume down and doesn't work. My Ipod doesn't have any shock or water damage. How can I do?

Hey rulosrojos,
The article linked below details a number of troubleshooting steps that can help restore functionality to your iPod nano.
iPod nano (6th generation): Hardware troubleshooting
https://support.apple.com/en-us/TS3474
Sincerely,
Allen

I just got a ipod nano 6th gen, and ive been using it for 2 days, and it seems that the battery just lasts about half a day, on playing 1 to 3 songs in intervals of 1-2 hours. Whats wrong with my ipod?

I just got a ipod nano 6th gen, and ive been using it for 2 days, and it seems that the battery just lasts about half a day, on playing 1 to 3 songs in intervals of 1-2 hours. Whats wrong with my ipod?

Your nano would really have nothing to do with it at that point. It is really something between iTunes and whatever server out there on the internet that it is trying to connect to for the update.
Try posting this one in the iTunes forum, they might have a solution for you.
i

My ipod nano 6th Gen. bought 5th Jan 2011 suddenly cannot be switched on. Last use is just 3h ago and everything went perfect til then Even shows no reaction when connected to charging cable. Anyone who can help?

My ipod nano 6th Gen. bought 5th Jan 2011 suddenly cannot be switched on. Last use is just 3h ago and everything went perfect til then Even shows no reaction when connected to charging cable. Anyone who can help?

See the Will not turn or screen remains dark section of this Apple support document to start troubleshooting the issue.
iPod nano (6th generation): Hardware troubleshooting
B-rock

My ipod nano (6th gen) keeps connecting and disconnecting itself from my computer can anyone help?

I have read numerous posts online about the same problem but can't seem to sort mine out. I've tried changing power leads, restoring back till an older version of itunes, resetting the ipod, restarting my computer and tried every USB port in sight but still nothing.
I have plugged a friends ipod touch into my computer and it connects and appears in itunes fine, but with mine it wont stay connected long enough for me to try and restore anything with it on itunes its literally a 1 second interval between connected and ejecting. I thought maybe it could be the connection terminal on the ipod but i have had it connected to a wall charger and xbox with it staying connected with no problems.
I am running windows vista on the computer and the nano was previously synced to a different itunes could this be the problem and if so how do I go about fixing it??
Thanks

I too am having this same issue. I connect my iPod nano (6th gen), and it appears for anywhere between 1 to 10 seconds and then automatically ejects.
I'm running a macbook pro with OS X 10.6.8 and the most up to date version of iTunes. The strange thing is that the nano works fine on my old macbook from 2007; which also has the most up to date iTunes but is running OS X 10.5. Another thing is that my iPod touch works just perfectly on my MacBook Pro.
I have read up on a lot of forums, and have found little help for those who are running into this problem on a Mac. The majority of fixes are for PC. Any help would be greatly appreciated.

I plugged my ipod nano 6th gen in to the latest version of itunes today and as soon as i plugged it it it turned on automatically as it should when i came back to it 5 mins later, picked it up and it felt warm and it wouldnt turn on. what should i do?

I plugged my ipod nano 6th gen in to the latest version of itunes today and as soon as i plugged it it it turned on automatically as it should when i came back to it 5 mins later, picked it up and it felt warm and it wouldnt turn on. what should i do?

I have the same problem and can't seem to figure out what the problem is. I rebuilt my iTunes library and still my 6G nano crahes whenever I load an AAC tune onto it. MP3s and podcasts all work fine, it's just the AACs...
Just *loading* an AAC song will cause the Nano 6G to reboot as soon as it disconnects from Itunes. It will then reboot a few times and then go into recovery mode. :-(
Karen

Ipod nano 6th gen is not recognized by itunes on a PC running Windows XP professional SP3, itunes 10.2

Running Windows XP professional SP3 and itunes 10.2.
I have followed every troubleshooting page on the apple support site yet my ipod nano 6th gen is not recognized by itunes (but it shows on my pc as a hard disk) weirder still, my ipod nano 3rd gen works just fine on this computer.
Whats wrong? HELP!!!
I have spent 3 days messing with my pc and have made no real progress.

gltg wrote:
Running Windows XP professional SP3 and itunes 10.2.
I have followed every troubleshooting page on the apple support site yet my ipod nano 6th gen is not recognized by itunes
I have spent 3 days messing with my pc and have made no real progress.
Then it's time to call Apple tech support while you are still under warranty. Every iPod comes with complimentary, single-incident telephone technical support within 90 days of your iPod purchase. If you also purchased AppleCare, then your warranty is extended for technical support and hardware coverage for two years from the original purchase date of your iPod.
U.S. iPod and Mac technical support: 1-800-APL-CARE (1-800-275-2273)

Ipod nano 6th gen not recognized by itunes

I recently updated my version of itunes and now whenever I plug in my ipod nano 6th gen an error message pops up saying it doesn't recognize my ipod. Why odes this even happen?

For anyone else having this problem, I found this solution to work. Try this first:
a) Get Windows to restart the drivers:
    - disconnect your USB device and close ITunes
    - connect your USB device
    - if ITunes loads, close it.
b) File explorer:
Open File explorer and browse to
C:\Program Files\Common Files\Apple\Mobile Device Support\Drivers
In that folder there should be a set of files named "usbaapl64...."
right click on the one ending in "INF"
Select Install. It's very quick.
remove the USB device
c) Restart the computer.
When you login again, load ITunes before you attach your USB device.
d)If you just want to add some photos, songs and movies from computer to your devices, you can use an iTunes alternative to do the job.
f) If still not works, try re-install iTunes. Go into the Unstall Programs (in Control Panel) and uninstall everything that says Apple, and uninstall Bonjour. With the fresh install of iTunes, everything came back and is should work. Hope it helps.
<Link Edited By Host>

Ipod Nano 6th Gen damaged Apple won't repair...any options?

I have had my Ipod Nano 6th gen for about 8 months and used it religiously during work outs...unfortunately I sweat a lot and apparently this will damage Ipod Nano to the point that Apple considers this to be outside the guidelines of normal manufacturer warranty. I am a little frustrated by this as I spend a fair amount of money on Apple products every year. Any advice on what I can do other than just sell it as damaged on eBay?

The best thing to do is consult Genius Bar. But as you have already said Apple does not honor the cause of damage and therefore not eligible for replacement. I recommend to visit an apple technical support to confirm the initial assessment.
You can try the out-of-warranty repair and determine how much it will cost you to repair. But try to weigh in cost of repair vs. a new replacement. Here is apple's statement about out-of-warranty repair.
If you want to set up your iPod for the Out-of-warranty service, we recommend that you take your iPod to a local Apple Retail Store. Alternatively, you can contact Apple Technical Support.
For more details, please refer to the Repair Pricing tab on the left.
If Apple determines that an iPod is not repairable, for example, if it has failed due catastrophic damage or the iPod has been disassembled into multiple pieces, then Out-of-Warranty Service is not available and the iPod will be returned. Please see Apple's Repair Terms And Conditions for further details.

IPod Nano 6th Gen - Functional but white screen on pressing wake/sleep button

Hi
I have an iPod Nano 6th Gen (out of warranty & applecare) - hasn't been dropped etc & never had any trouble.
This morning I got the white screen after unplugging it from charging.
I have tried hard reboot (power button + vol down). I have put it into disc mode (hard reboot + both volume buttons) and restored it to factory settings from itunes (10.6.3) . I've even put it into diagnostic mode and looked around to see if there were any tests I could do.
Functionally the ipod works ok - plays music, volume changes, and it will shuffle on shaking/ play pause on double pressing the power button.
The problem is when I switch off the screen by pressing the power button once - if I try to switch the screen on again I only get the white screen (although this doesn't affect music playing etc).
The way to get around this is either doing a hard reboot (which is a pain as it removes all my settings) or by switching off the ipod, waiting 5 minutes, then switching it on again (this preserves my settings). If I switch off the ipod and try to switch it back on within 5 mins, it's straight to the white screen.
The only other odd thing I noticed was that the screen was shaky/jolty and graphics not quite lining up etc, but this only lasted 10s and went once I started playing music...
Any ideas as to what is causing this? I'm guessing maybe a hardware problem but it seems strange that there is no white screen on switching on, just from waking.
It was a present from my dad and I'm very fond of it so would like to keep it/fix it if possible!
Thankyou!

Hello bfsf,
Welcome to the Apple Support Communities!
I understand that your iPod nano (6th generation) displays a white screen after waking from sleep. First let my say that you have completed some great isolation and troubleshooting steps on your own. Because the issue is still present after the fantastic troubleshooting you already completed, it may be necessary to have this iPod evaluated for service. If you would like more information on this process, please read over the information in the attached link.
Apple - Support - Service Answer Center
Cheers,
Joe

IPod nano 6th gen won't play my music.

My iPod nano 6th gen has worked fine for years and when I synced it recently it would play some tunes fine, cut some off mid-way through and skip some completely. The first thing I done was just tried to sync it again but this didn't make a difference so I reset my iPod through iTunes and synced it again but this made it worse, when I pressed play it comes up with the pause button but if I go to the next screen where you can see how far through the song is the bar wasn't moving, so the tunes aren't playing, so following this I formatted my iPod on my pc and then reset it on iTunes (I had to replace the folders I had removed during formatting) and that didn't do anything it still won't play anything. It's not my headphones as they work fine in my pc, and it's not my music as it worked fine before and they all play fine on my pc. What else can I do?

What do you mean by select tracks? It will only play particular tracks or repeatedly play a particular track? What format are these problem tracks in?
B-rock

Ipod nano 6th gen, wierd functionality problems

I got this ipod nano 6th gen refurbished from apple a year back. I just started using it and found that after I synced it with my itunes, i have the following problems :
1. The screen display is opposite than my previous ipod (landscape vs portrait).
2. I have to manually change to next song most of the time.
3. When I change songs, it plays a song a few seconds and then skips a few before stopping on a song.
4. The song playing is not the song displayed on the screen.
Tried restoring to factory settings. Same issues. Can someone help?

Hi zenpal1,
If you are having multiple issues with your iPod nano that persist after a factory restore, you may need to have your iPod evaluated or serviced. You may find the following page helpful:
Apple - Support - Service Answer Center
http://support.apple.com/kb/index?page=servicefaq&geo=United_States&product=ipod
Regards,
- Brenden

My ipod nano 6th gen just blinking

Similar Messages

Maybe you are looking for