My ipod w/ clickwheel does not link after new iTunes install using dock

I have had this ipod for 5 1/2 years without problems; it even holds a good battery charge. After updating to the new iTunes, now for some reason my ipod will not be recognized when I plug the ipod into the dock that came along with this computer (this is when connected to the firewire 400 port on my iMac G5). There was no problems in the past and I only experienced this after updating to the new iTunes. Anyone else had this problem?

I really think this was just a problem with the new iTunes. After the update I did not experience this problem any longer.

Similar Messages

Updated touch ipod now it does not show up on itunes

updated my touch ipod now it does not show up on itunes----the ipod is showing itunes logo an arrow and the plug---and it just stays that way, can anyone help---PLEASE!!

I have the same

HT3917 My apple wireless keyboard is not working after new batteries installed

My apple wireless keyboard is not working after new batteries installed.

Do you get a steady green light to say there is a connection. If not, are the batteries the right way round. Do you have a monitor to tell the batteries strength. Is there a reading. Are the batteries good quality ones, Duracell, Energiser or Apple rechargeables.

EPrint does not work after new wifi router on Verizon DSL

I have been using ePrint on my iPod, iPad, and iPhone for a few months without a problem, but recently had to switch to a new wifi router on my Verizon DSL, as my wifi kept turning off and Verizon's solution was an updated wifi router. Since the switch, I cannot ePrint from my mobile devices. I can, after reconfiguration, print from my laptops. The ePrint app still finds the Deskjet 3050a, says "sending to printer", but will not print. The ePrint is turned on. I tried to delete the app and reinstall in hopes that I can start fresh, but it still does not work. I tried to add a new printer, with the email supplied on the ePrint screen on the printer, but nothing.
Any ideas?

Hi Honor Student
Is your printer connected to the new router as it sounds like it is still looking for the old one ? Maybe just disconnect it and reconnect it again to your new router and then the ePrint APP should pick it up.
I work for HP.
Thanks
Caroline
Although I am a HP employee, I am speaking for myself and not for HP.

Ipod touch will not sync after new itunes update

Ipod touch 4th generation will not sync after I updated the new itunes. Actually after I updated to the new itunes it deleted all my music from my ipod and refuses to reload. If someone could please help me that would be completely appreciated. I tried trying to sync each song individually but it didn't help (before it stopped syncing), then it stopped syncing, even though I have it hooked up it brings everything that I have on my ipod up but it won't do anything.

When I tried the first time it asked me if i wanted it to stop syncing and to restore. It gave the choices of yes and cancel, i didn't click either because the option box went away and it just stopped restoring on its own. I did the store again and now it is asking if i want to set up as a new ipod or to restore to Andrea's ipod. Should I set up as new?
Thank you Espeon for the article

Photoshop Elements 7 does not start (after 3 years i used it)

Yesterday, when i opened my Photoshop Elements 7 (I use it on my PC from 3 years), after the splash screen, an alert windows says to me that there is an error and suggested to restart PC or reinstall product. The program automatically closed itself.
I'm not able to write the exact sentence of the alert, because now PE7 does not start at all. Not even the alert with the error message.
I always used this product in this 3 years (from this PC), without problems.
PE7 was preinstalled and pre-registered by the constructor of PC (Sony-Vaio). So, now i have not even the registration key to reinstall PE7.
Furthermore, I tried to open Adobe Premiere Elements 7 (also, preinstalled and pre-registered, but never used), and after splash screen the program automatically close itself.
What can I do??!?
Thanks you all.

No result by disconnecting from the network. Even if I restart PC.
But.... I SOLVED the problem!!!!!
The problem was "FLEXnet Licensing Service"
Thanks to last tip, that leads to another failure... I remembered that 2 days ago I tried to optimize my PC by stopping some service with MSConfig. One of the disabled services was "FLEXnet Licensing Service".
Searching in google, now i know that "Flexnet Licensing service is used by most Adobe products to prevent piracy".
So, some Adobe products do not start, if Flexnet Licensing service is not running.
Thank you very much for tips, and help in general... very helpful (to investigate the nature of the problem).

Secondary monitor does not work after OS X install

My secondary monitor does not work well after OS X install. The image on my secondary monitor is different even the screen svaer image is different and the mouse can not be seen.

Try the easy thing first - NVRAM reset:
Shut down your Mac.
Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.
If that does not work, post back with more info, including the version of Mac OS you are running. How is the external monitor connected, did it ever work, and from what OS X to what was the "OS X install" in your title?

DHCP Server does not work after Exporting and Importing Using Netsh Command

Hello Friends :
I had two dhcp servers in windows server 2003 server , I have upgraded one of them to windows server 2008 32 bit and again i installed a windows server 2008 R2 as an additional Domain Controller , the last scenario was like this :
srv-1 : windows server 2003 + DHCP = working with no problem
srv-2 : windows server 2003 + DC + DHCP = Worked without problem
srv-3 : windows server 2008 R2 + DC = worked without any problems
I exported the DHCP server configuration on the srv-2 using netsh dhcp server export and Imported them to srv-3 using the
netsh dhcp server import command , the command completed successfully and i can see all of the scopes without any problems and errors , i have authorized the new server without any problem , all scopes are activated without any problem so i
disabled the srv-2 DHCP service and unauthorized it from active directory , the problem is that the new server semms that does not lease any address to clients !!!
1- I have authorized it
2- I used Rogue Checker tool in client computers they see authorized server without any problems
3- The same tool in workgroup only shows srv-1 as the DHCP server and does not see other DHCP servers
4- Bindings are OK and DHCP servers only have one NIC installed on them
What can i do to make sure my srv-3 DHCP server will work on the network ?
thanks ...
MIMO

Are the clients on another network so you need to configure a DHCP relay agent?
If you load up perfmon on the dhcp server and remove all counters and then add DHCP counters. Do you see any dhcprequests when you reboot your dhcp clients? This will determine if your server actually receives any dhcp requests.
Have you check event viewer for any warnings or errors?
And the classic one restarted the dhcp server service (or reboot)?
Regards Per-Torben Sørensen http://pertorben.wordpress.com/

Itunes does not open after saying successfully installed

I have downloade the latest itunes. It says successfully installed but it does not open. I have restarted the computer but it still does not open. What can I do?

Try following steps one at a time:
1. Restart computer, right mouse click iTunes icon and select "Run As Administrator"
2. If that does not work, check to see if this file APSDaemon.exe is the problem here.
Close your iTunes.
Press Ctrl-Alt-Del key and choose Task Manager. In the "Processes" Tab, select the file APSDaemon.exe and click End Prosses button, then close the task manager window.
Now open itunes and see if it is working?
If that works, to prevent having to do the same process everytime you restart Windows, go to. START button, type in
MSCONFIG
Hit ENTER
Click STARTUP Tab, Uncheck "Apple Push", click OK.
Restart Windows.
3. If that fails or you don't see ApsDaemon.exe in the Processes, refer to following article to remove SC files:
http://support.apple.com/kb/TS2363
4. If that fails, repair or reinstall your Quicktime. START / CONTROL PANEL / PROGRAMS N FEATURES / hightlight QUICKTIME and click REPAIR.

Audiobooks not working after new iTunes installation

My hard drive recently crashed and I've had to setup all of my iTunes library again. The problem I am having is on my audiobooks. iTunes will not allow me to add them to my library and when I try to open the files manually I get the following error...
"Error -2048: Couldn't open the file **.m4b because it is not a file the QuickTime understands."
I made sure that my software was updated and it is. Any help would be appreciated.
Thanks.

The type of password protection you use to protect your wireless network, in your case WPA-PSK/TKIP, has no bearing on whether iTunes Home Sharing can work or not. That type of password protection is there to keep other people within the vicinity of your wireless network from being able to join your network and gain access to the files on your computers.
The key to Home Sharing is that every computer or device that wants to participate must be on the same network and that they are all using the same Apple ID. Provided you are all joining the same network, you will know you are if you are all joining a network of the same name, and using the same password, then Home Sharing should work. The other thing is that all the computers and devices have Home Sharing turned on using the same Apple ID.
If nothing else changed other than the router, the network name, the password to join the wireless network and the type of encryption used to secure that network then once those computers joined the wireless network Home Sharing should have continued to work as it did before.
What I suggest is that you turn Home Sharing off and then on again on each computer or device making sure you are using the same Apple ID.
Also, turn on Library Sharing, this is done in the preferences for iTunes, as see if you can access each others shared iTunes library that way. Library Sharing only works between computers, iPhones can't participate, and does not require Apple IDs or a link to iTunes to work.
See my post in the thread I've linked to below to learn how to turn on Home Sharing, Library Sharing and how to identify the difference.
https://discussions.apple.com/thread/3461734

Mac Pro not starting after new RAM install.

Hey everyone,
I have a Mac Pro Mid 2010 2x2.66 GHz 6-core (12core) Mac Pro with OSX 10.7.5. I currently have 6gb 1333 MHz DDR3 ECC ram installed.
I ordered 16gb (2x8gb sticks) of RAM from newegg, specifically, 2 sticks of this ram:
Kingston 8GB DDR3 1333 ECC Registered Memory for Apple
I popped it in yesterday and when I try to start up, the LED light just flashes and the screen acts as if nothing the computer hasn't been turned on. It does not beep or make any startup sounds either.
As far as I can tell this memory is in spec. It is "Registered", could this be a potential problem? I have tried various configurations of which slots to put the ram in. The only thing I haven't tried is putting the 2x8gb sticks in by themselves to see if it might be a capacity or mixing of ram issue.
Does anyone have experience with this or know where I might be going wrong?

What you have not done is actually... what I would have done first to start with!
To make sure it works and works alone.
Mixing is suppose to work now, better, but as OWC found earlier, mix and match requires DIMMs that will.
There is more in depth on MacRumors about ranking, Registered and much more about using 3rd party and what to look for and does or does not work. Which is nice, they try and tend to keep everything in one place, one thread, easy to find and read.
And Newegg price isn't really different than say buying from MacSales.

IPod 1st gen does not work after upgrade to iOS 3.1.3. Does anyone know how to fix this?

I upgraded my iPod 1st Generation from 1.1.5 to iOS 3.1.3. through iTunes. After it went through the upgrading process, I received the error message, "iPod could not be restored. An unknown error occurred (6). I went to another PC and was able to restore to the original version. However, I would like to be able to upgrade to 3.1.3 so that I can buy some Apps that requires 3.1.3. Does anyone know how to fix this or have any suggestions? Thanks.

Error 2, 4 (or -4), 6, 40, 1000, 9006
Follow Troubleshooting security software. Often, uninstalling third-party security software will resolve these errors.
There may be third-party software that modifies your default packet size in Windows by inserting a TcpWindowSize entry into your registry. Your default packet size being set incorrectly can cause these errors. Contact the manufacturer of the software that installed the packet size modification for assistance or follow this article by Microsoft: How to reset Internet Protocol (TCP/IP).
Verify that access to ports 80 and 443 are allowed on your network.
Verify that communication to albert.apple.com or photos.apple.com is not blocked by a firewall, or other Internet security setting.
Discard the .ipsw file, open iTunes and attempt to download the update again. See the steps underAdvanced Steps > Rename, move, or delete the iOS software file (.ipsw) below for file locations.
Restore your device while connected to a different network.
Restore using a different computer.
http://support.apple.com/kb/TS3694#error6

Ipod Classic 160GB connects but does not sync to new itunes

I'm having a lot of trouble after installing the latest itunes. My iTunes picks up the ipod as a device but will not sync with it. I've tried to just sync it, ive shut down itunes and turned the ipod off and tried, i've ticked the box that says "convert higher bit rate songs to 128kps AAC" and tried to sync and unticked the box and tried as well. I have also tried going to File ->Devices->sync, and the sync button is shaded so i can't click on it. I have also reset it to factory settings and tried. I'm out of ideas, does anyone else have any?

Hello DeclanConky
Check out the article below to troubleshoot if it is software or hardware. Try starting up in Safe Mode or try it out in another user. Also when you removed iTunes, did you remove the other associated files Apple in the specific order indicated in the second article? Let me know if this works out or need to continue troubleshooting.
iTunes for Windows Vista, Windows 7, or Windows 8: Fix unexpected quits or launch issues
http://support.apple.com/kb/ts1717
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
http://support.apple.com/kb/ht1923
Regards,
-Norm G.

HT1386 I have one album on my IPod Touch that does not show up on ITunes.

I am trying to download my music to the libraries on my computer. I noticed that one of my albums is not showing on ITunes but is showing up on my IPod.

No problem. Glad to have helped.
Not sure as to why it happened. I just know this has been happening to a few users lately. It may be with how you have your iPod touch configured to sync Podcasts. So you may want to double check these settings as well as mess around with them a bit to figure out if that is the cause. Otherwise, I'm not entirely sure on this one. Sorry I cannot be of much help here.
B-rock

HT1937 My Iphone does not work after buying it and using it for 3 months how can I gert it fixed?

I brought my Iphone on the At and T site 3 months ago and it's not working how can I have it repaired?

I think that you should just contact the place you bought it from and have them take a look at it, and if you have the warrenty on your iPod you can get a new replacement too.

My ipod w/ clickwheel does not link after new iTunes install using dock

Similar Messages

Maybe you are looking for